粉土界面恒刚度循环剪切试验研究

竖向循环荷载作用下桩土界面的作用机理是研究桩土摩擦疲劳的关键。针对循环荷载作用下桩-粉土界面的剪切性能,使用改进的剪切试验装置在恒刚度条件下进行循环剪切试验,研究循环次数、累积位移和法向刚度对其摩擦疲劳性能、循环后单调剪切性能的影响。试验结果表明,粉土在循环剪切过程中,法向应力和剪应力在初始10个循环内随循环数增加快速衰减,随着循环进行,逐渐趋于稳定;单次循环内在剪切位移方向变化时,土体呈现表现出剪缩-剪胀-剪缩交替现象,总体变形呈现剪缩的趋势;循环荷载作用下,粉土界面的法向应力和剪应力随法向刚度增大衰减速率增大,达到稳定的累积循环位移越小;粉土循环后的单调剪切、法向应力恢复的单调剪切的剪应力比小于首次单调剪切试验值,且法向应力恢复的循环后剪切试验的剪胀程度较小,表明循环剪切过程中界面处粉土颗粒棱角破碎,颗粒变得光滑。在对试验数据分析的基础上,提出了与累积位移、法向刚度和初始应力相关的无量纲累积位移,建立了法向应力和界面摩擦角随累积位移的衰减方程。     

Experimental research on dynamic response of PZT-5H under impact load

In order to improve the stability of PZT-based sensors, the mechanical, dielectric, ferroelectric and piezoelectric properties of PZT-5H under impact load were studied experimentally by using the separated Hopkinson pressure bar (SHPB) with an electrical output measurement device. At the same time, the experimental study on the material properties of PZT-5H before and after the impact was carried out. The effect of impact cracks on the output voltage of PZT-5H was also analyzed. The results show that the dynamic piezoelectric constants of PZT-5H under low stress impact (10–50 MPa) are different from those under quasi-static state, and the empirical relationship between them and the peak stress is obtained through experiments. The dielectric properties of PZT-5H did not change under low stress impact, but micro-cracks occurred in the material and dielectric loss increased at high frequencies. Under short circuit, the residual polarization intensity of PZT-5H decreases sharply due to impact load. While the impact load causes the secondary polarization and the increase of the residual polarization intensity of PZT under open circuit. When the stress is over 45 MPa, the PZT-5H breaks. The formation of cracks causes abnormal discharge voltage and gap discharge.     

基于深度卷积神经网络的视觉里程计研究

视觉里程计利用视频信息来估计相机运动的位姿参数，实现对智能体的定位。传统视觉里程计方法需要特征提取、特征匹配/跟踪、外点剔除、运动估计、优化等流程，解算非常复杂，因此，提出了基于卷积神经网络的方法来实现端对端的单目视觉里程计。借助卷积神经网络对彩色图片自动学习提取图像帧间变化的全局特征，将用于分类的卷积神经网络转化为帧间时序特征网络，通过三层全连接层输出相机的帧间相对位姿参数。在KITTI数据集上的实验结果表明，提出的Deep-CNN-VO模型可以较准确地估计车辆的运动轨迹，证明了方法的可行性。在简化了复杂模型的基础上，与传统的视觉里程计系统相比，该模型的精度也有所提高。     

Structural,electrical, optical and dielectric properties of yttrium substituted cadmium ferrites prepared by Co-Precipitation method

The yttrium substituted cadmium ferrites having composition Cd_1-xY_xFe₂O₄ (X = 0.00, 0.125, 0.250, 0.375, 0.500) were synthesized by the co-precipitation method and sintered at 1100 °C for 6 h. Structural, morphological, electrical, optical and dielectric characteristics were explored by XRD, SEM, EDS, FTIR, I–V two probes, UV–Vis and LCR techniques.XRD results confirmed the cubic structure of spinel ferrites. A decrease in lattice constants of the prepared samples was observed with the substitution of Y ions and was attributed to the difference in ionic radii of Y³⁺ (0.95 Å) and Cd²⁺ (0.97 Å) ions. Cationic distributions, ionic radii of both tetrahedral and octahedral sites, tolerance factor, oxygen positional parameters, bond lengths, interatomic distances, positional parameters and bond length angles were calculated from XRD data. The morphology of the prepared ferrites was studied using SEM and results ratified the XRD results. EDS confirmed the presence of all inserted elements in Cd_1-xY_xFe₂O₄ composition. DC resistivity and drift mobility of soft-ferrites were found to be increased from 1.047 × 10⁸–4.822 × 10¹⁰ Ω-cm and 5.87 × 10⁻¹² – 1.045 × 10⁻¹⁴ cm²V⁻¹s⁻¹, respectively, at 523 K with yttrium content confirming the behavior of semiconductor materials. The optical band gap energy calculated from the UV–Vis pattern of the Cd_1-xY_xFe₂O₄ system was decreased from 3.6011 to 2.8153 eV. DC resistivity and optical band gaps exposed inverse relation. FTIR results revealed lower and upper-frequency absorption bands in the ranges of 419.31–417.01 cm⁻¹ and 540.95–565.70 cm⁻¹, respectively. Dielectric constant and dielectric losses were in decreasing order, while ac conductivity revealed rising behavior with increasing frequency. Results showed the potential of yttrium doped Cd nanoferrites for applications in high-frequency microwave absorbing devices.     

On keys' meanings and modes: the impact of different key solutions on children's efficiency using a mobile phone

The present study investigates the impact of different key solutions of mobile phones on users' effectiveness and efficiency using the devices. In the first experiment, 36 children (9 - 14 years) and in the second experiment 45 young adults (19 - 33 years) completed four common phone tasks twice consecutively on three simulated phones that had identical menus, but different key solutions. An approach was undertaken to quantify the complexity of keys in three models, incorporating different factors contributing to the keys' complexity (number of key options, number of modes and number of modes with a semantically dissimilar meaning), in order to predict users' performance decrements. As a further main factor, the degree of the users' locus of control (LOC) was measured and interactions with performance outcomes were studied. As dependent measures, the number of inefficient keystrokes, the number of tasks solved and the processing time were determined. Results showed a significant effect of control key solutions on users' efficiency and effectiveness for both children and young adults. Moreover, children's LOC values significantly interacted with performance: children with low LOC values showed the lowest performance and no learnability, especially when using keys with a high complexity. From the three factors contributing to the complexity of keys, keys exerting different functions with semantically inconsistent meanings had the worst effect on performance. It is concluded that in mobile user interface design keys with semantically inconsistent meanings should be generally avoided.     

Annealing effects on structural and electrical properties of fluorinated amorphous carbon films deposited by plasma enhanced chemical vapor deposition

The annealing effects on the structural and electrical properties of fluorinated amorphous carbon (a-C:F) thin films prepared from C₆F₆ and Ar plasma are investigated in a N₂ environment at 200 mTorr. The a-C:F films deposited at room temperature are thermally stable up to 250 °C, but as the annealing temperature is increased beyond 300 °C, the fluorine incorporation in the film is reduced, and the degree of crosslinking and graphitization in the film appears to be enhanced. At the annealing temperature of 250 °C, the chemical bond structures of the film are unchanged noticeably, but the interface trapped charges between the film and the silicon substrate are reduced significantly. The increased annealing temperature contributes the decrease of both the interface charges and the effective charge density in the a-C:F film. Higher self-bias voltage is shown to reduce the charge density in the film.     

石化装置蒸汽发生系统的仪表工程设计

主要探讨了某石化装置蒸汽发生系统的仪表工程设计，提出了复杂控制方案、联锁方案设计，同时也详述了影响系统设计的因素，如测量补偿和迁移等。     

环氧树脂及其增强材料回顾

本文回顾了PCB制造常用的环氧树脂及其增强材料的性能和用途。同时,还介绍了代用树脂材料和代用增强材料的最新进展,如改性环氧树脂、无卤树脂、Thermount、PTFE、氰酸酯等,并就其性能进行了探讨。     

高坝通航技术在水口工程的新发展

水口水电站坝高101m,航运过坝采用一线三级船闸和一线垂直升船机。水口升船机是当时国内已建和在建同类升船机中总体规模最大的升船机,也是我国第一座自行设计、制造、施工和安装的大型升船机。在塔楼结构动力分析和试验研究、塔楼滑框倒模施工、升船机整体模型试验研究、承船厢整体制造和浮运、船厢安全锁定装置和船厢对接密封装置试验研究、整机安装及联调试验等方面充分体现了水口升船机的建成是高坝通航技术的新发展。     

甲基叔戊基醚合成反应的热力学分析

利用戊烯与甲醇合成甲基叔戊基醚(TAME)反应的热力学平衡实验数据, 选择不同的混合活度模型,分别计算得到了该反应体系的平衡常数,并与理论计算得到的平衡常数相比较,筛选出了适合该反应体系的活度计算模型.