Assessment of local strain field in adhesive layer of an unsymmetrically repaired CFRP panel using digital image correlation

The present study focuses on experimental investigation of through the thickness displacement and strain field in thin adhesive layer in single sided (unsymmetrical) patch repaired CFRP (carbon fiber reinforced polymer) panel under tensile load. Digital image correlation (DIC) technique is employed to acquire the displacement and strain (longitudinal, peel and shear) field. Experimental determination of shear transfer length based on shear strain field obtained from DIC is introduced to estimate the optimum overlap length which is an essential parameter in patch design for the repair of CFRP structures. Further, DIC experiment with magnified optics is performed to get an insight into complex and localized strain field over thin adhesive layer especially at critical zones leading to damage initiation. The failure mechanism, load displacement behavior, damage initiation and propagation are closely monitored using DIC. The influence of patch edge tapering on strain distribution in adhesive layer is also investigated. The DIC successfully captures the global and localized strain field at critical zones over thin adhesive layer and further helps in monitoring the damage based on strain anomalies. Strains are found to have maximum magnitude at the patch overlap edge and the shear strain level in adhesive layer is higher than the peel strain. Normal tapering increases the peel strain and has negligible influence on shear strain level in adhesive layer. The recommended overlap length is found to be consistent with the recommendation in the literature. Whole field strain pattern and the overlap length obtained from experiment are further compared with the finite element analysis results and they appear to be in good coherence.     

Simultaneous accommodation of Dy3+ at the lattice site of β-Ca3(PO4)2 and t-ZrO2 mixtures: Structural stability,mechanical, optical,and magnetic features

Structurally stable β-Ca₃(PO₄)₂/t-ZrO₂ composite mixtures with the aid of Dy³⁺ stabilizer were accomplished at 1500°C. The precursors comprising Ca²⁺, P⁵⁺, Zr⁴⁺, and Dy³⁺ have been varied to obtain five different combinations. The results revealed the fact that complete phase transformation of calcium-deficient apatite to β-Ca₃(PO₄)₂ occurred only at 1300°C, whereas the evidence of t-ZrO₂ crystallization is obvious at 900°C. The dual occupancy of Dy³⁺ at β-Ca₃(PO₄)₂ and t-ZrO₂ structures was evident; however, Dy³⁺ initially prefers to occupy β-Ca₃(PO₄)₂ lattice until its saturation limit and thereafter accommodates at the lattice site of ZrO₂. The typical absorption and emission behavior of Dy³⁺ were noticed in all the systems and, moreover, the surrounding symmetry of Dy³⁺ domains has been determined from the luminescence study. All the systems ensured paramagnetic response that is generally contributed by the presence of Dy³⁺. A gradual increment in the phase content of t-ZrO₂ in the composite mixtures ensured a significant improvement in the hardness and Young's modulus of the investigated compositions.     

户内热转印粉末涂料用混合型聚酯树脂的合成研究

通过分析热转印性能的影响因素合成了不同结构的聚酯树脂，研究了树脂酸值对热转印性能的影响，同时研究了部分单体对聚酯树脂热转印性能的影响。采用 DSC热分析法研究了固化促进剂对粉末涂料固化行为的影响，结果表明：选择合适的固化促进剂对涂层转印性能的提高有至关重要的作用。     

复合外加剂改性盐石膏的研究

盐石膏的主要成分为无水硫酸钙,其活性差、凝结硬化慢、强度低,需要添加活性剂来激发盐石膏的活性。通过复合外加剂对盐石膏加以改性,并通过XRD和SEM对其作用机理做了分析。结果表明,单掺脱硫石膏和建筑石膏均能缩短盐石膏的凝结时间,建筑石膏的效果较好,但掺量不宜过高。复掺建筑石膏和缓凝剂时,两者比例要控制得当,适宜的建筑石膏和缓凝剂掺量分别为50%和0.10%~0.12%（质量分数）。分析可知,大掺量建筑石膏会增加盐石膏硬化体中二水相和针棒状晶体的含量;缓凝剂掺量的增加,会降低盐石膏硬化体中二水相的含量,棱形晶体增多,从而降低了盐石膏的强度。     

垦71井区三维VSP资料波场分离方法应用研究

三维VSP资料是多偏移距VSP资料，资料中多种类型的波叠合在一起形成复杂波场。从复杂波场中分离出单一的保幅反射波波场是三维VSP波场分离的重要工作。常规二维VSP波场处理方法单一，难以适用于复杂的三维波场处理。针对三维VSP资料的波场特点，以分离上行反射P波为例，将单一波场分离方法加以适当组合，对垦71井区三维VSP实际资料进行了应用研究。结果表明，波场分离处理中叠加消去法和中值滤波相结合以及F—K滤波和中值滤波相结合的方法克服了单一方法的缺陷，波场处理后获得了波组特征明显、波场清晰单一的上行反射P波保幅波场，取得了较好的波场分离效果。     

人工颅骨用复合材料中微量甲基丙烯酸甲酯的气相色谱法测定

采用氢气焰离子化检测器(FID),以正丁醇为外标物,PEG-20M为固定相,甲醇作为溶剂,气相色谱法测定复合材料人工颅骨中微量MMA的含量。其相对标准偏差<0.022,平均回收率(n=4)为98.0％～99.1％。此方法操作简便,用于实际样品分析可得到满意的结果。     

复合材料的最新进展与应用

叙述了复合材料的发展概况 ,详细介绍了增强材料的种类、性能、形式及加工技术 ,指出了复合材料具有广阔的应用前景     

Ni-Al2O3纳米复合电镀工艺的初步研究

初步研究了复合电镀各工艺条件：电流密度、镀液pH值和温度以及搅拌方式对Al2O3纳米微粒在镍基复合镀层中含量的影响。研究表明：电流密度增大不利于提高镀层中纳米微粒的含量；pH值增大也明显使复合量降低;镀液温度升高，镀层中微粒的复合量随之略有改变；电镀时，加强搅拌或适当改变搅拌方式，可以使复合镀居中的纳米微粒含量提高。还利用扫描电镜及能谱对Ni-Al2O3镀层表面进行了观察与分析。     

陶瓷及陶瓷基复合材料微缺陷的超声检测

为研究陶瓷及陶瓷基复合材料微缺陷的超声检测能力，针对一些人工缺陷试样进行了超声检测试验。试验主要采用了纵波垂直入射法和泄漏瑞利波法。通过试验结果，比较了两种方法的检测能力。     

负载型复合载体及其镍基催化剂的性能

采用溶胶-凝胶法制备了负载型ZrO_2/Al_2O_3和ZrO_2/Al_2O_3-SiO_2复合载体,研究了不同复合载体对Ni基催化剂CO_2重整甲烷反应和性能的影响,并用XRD、IR、TPR、TPD和BET等方法对复合载体及催化剂进行了表征。结果表明,ZrO_2负载在基载体后比表面积、碱性、活性组分Ni的分散度和Ni与ZrO_2的相互作用增大。NiO在复合载体表面的分散容量与ZrO_2的负载量有关,ZrO_2的负载量为37．5%时NiO的分散容量达最高值(24．0%)。与Ni/ZrO_2相比,Ni/ZrO_2/Al_2O_3-SiO_2和Ni/ZrO_2/Al_2O_3催化剂对CO_2的吸附能力增大,CO_2吸附量增加,酸强度降低,CO_2重整CH_4反应活性提高,其中以Ni/ZrO_2/Al_2O_3催化剂的活性最好。