川北某黑色页岩型铼矿工艺矿物学研究

通过矿相显微镜、扫描电镜、电子探针、X射线能谱元素面分析等多种手段综合研究了川北某黑色页岩型铼矿中铼的赋存状态。样品为黑色页岩,有机碳含量较高。粘土矿物总量为14.6%,黄铁矿含量16.2%,石英含量37.7%。样品具典型的粘土结构,矿物粒度微细。铼有两种赋存状态,一种呈类质同象形式赋存于黄铁矿内,另一种则以分散形式存在。典型黄铁矿测点Re平均含量为0.024%。黄铁矿是Re的重要载体矿物。建议通过浮选分离黄铁矿,从而实现Re的富集。      

浅析混凝土搅拌站的防雷

近年来,我市因雷击而导致搅拌站系统瘫痪停产、影响工程进度的事件时有发生,在针对混凝土搅拌站配料秤的实际检定工作中,也常发现配料秤的称重传感器因雷击损坏而影响计量准确性。因此,对混凝土搅拌站防雷的研究具有重要意义。本文阐述了雷电对混凝土搅拌站的主要危害,分析了混凝土搅拌站常见的雷击原因及其防护措施,旨在引起生产方、安装方以及使用方对混凝土搅拌站防雷的共同重视。     

磷酸高效分解磷矿实验研究

为改进湿法磷酸生产工艺,提高副产石膏的品质,减少湿法磷酸固体副产物磷石膏堆存产生的经济和环保压力,进行了磷酸分解磷矿制磷酸的实验研究。采用贵州某磷矿为主要原料,研究了湿法磷酸预分解磷矿的反应条件。通过单因素实验确定了湿法磷酸分解磷矿最优反应条件：反应温度为75 ℃,磷酸与磷矿的质量比（液固比）为9,反应时间为3 h,磷酸质量分数为30%（以五氧化二磷计）。在此条件下,磷矿的分解率为98.62%。     

Control of the particle microstructure during the synthesis of bulk-polymerized transparent methacrylate-acrylonitrile-butadiene-styrene resin

A series of methacrylate-acrylonitrile-butadiene-styrene (MABS) resins was prepared using bulk polymerization. The polarity of the continuous phase and the compatibility of two phases were changed by adjusting the methyl methacrylate (MMA) content, choosing values that were close to styrene-butadiene rubber solubility value. The possibility of controlling the microstructure of the MABS resin by changing the polarity of the components and the compatibility of two phases was assessed. The dynamic mechanical analysis shows that the compatibility of two phases varies with the MMA content. The morphological analysis shows that increasing MMA contents results in a gradual decrease in the sub-inclusion structure with a network skeleton of rubber particles, and that all the particles become solid rubber when the MMA content reaches 75%. The sub-inclusion structure reappears but does not have a network skeleton when the MMA content is 90%. The impact strength and morphological analysis indicate that the solid rubber particles and the sub-inclusion structure with a network skeleton provide excellent toughness, while the sub-inclusion structure without a network skeleton does not. In contrast, the transmittance of the ABS resin first increased and then decreased with increasing MMA content.     

A handheld sensor assay for the identification of grouper as a safeguard against seafood mislabeling fraud

Increases in international trade and global seafood consumption, along with fluctuations in the supply of different seafood species, have resulted in fraudulent product mislabeling. Grouper species, due to their high demand and varied commercial availability, are common targets for mislabeling by exploiting inefficient inspection practices. Compounding this problem is the fact that there are currently 64 species of fish from eleven different genera allowed to be labeled “grouper” per U.S. Food and Drug Administration guidelines. This wide diversity makes it difficult for regulators to discern legally salable groupers from restricted species. To obviate taxonomic misidentification when relying on external phenotypic characteristics, regulatory agencies are now employing genetic authentication methods which typically offer species-level resolution. However, standard genetic methods such as DNA barcoding require technical expertise and long turnover times, and the required instrumentation is not amenable for on-site analysis of seafood. To obviate some of these limitations, we have developed a handheld genetic sensor that employs a real-time nucleic acid sequence-based amplification assay (RT-NASBA) previously devised in our lab, for the analysis of fish tissue in the field. The base RT-NASBA assay was validated using a lab-based, benchtop RNA purification method as well as non-portable, commercial RT-NASBA analyzer. Described herein, is an uncomplicated method for purifying RNA from fish tissue in the field, which had similar efficiency to the benchtop method demonstrated through direct comparisons. We have also demonstrated that the field sensor is only slightly less sensitive than the benchtop instrument, and could discern 80.3% of groupers (no target sequence available for three species) on the 2014 FDA Seafood List from potential impostors. The complete field assay requires fewer than 80 min for completion and can be performed outside of the lab in its entirety.     

南水北调中线工程受水区二期需调水量预测研究

2002年12月国务院批复了《南水北调工程总体规划》，明确中线工程分两期建设。目前，一期工程已经通水。近年来，随着社会经济的快速发展，受水区的人口、生产规模、节水水平、人们对环境的要求都发生了变化，因此有必要根据新的情况对受水区的用水需求重新预测。分析了城市化发展和城镇用水变化的新形势，依据流域、区域水资源规划成果，提出了中线二期工程受水区需调水量，并与《南水北调中线工程规划》提出的二期需调水量进行对比，以供各方参考。     

Sensor network design based on system-wide reliability criteria. Part I: Objectives

Reliability based criteria are quite popular for optimal sensor network design. We present a modified definition of system reliability for sensor network design for two applications: reliable estimation of variables in a steady state linear flow process, and reliable fault detection and diagnosis for any process. Unlike the weakest-link based definition of system reliability in the literature, the proposed definition considers the entire system and is consistent with the reliability concept used in classical reliability literature. For each application, dual approaches for defining system reliability are proposed, and their analogy with the reliability problem in the classical reliability literature is established. Using examples and stochastic simulations, the advantage of using the proposed system reliability in contrast to the existing definition is illustrated. Part II of this series of articles presents methods for efficient generation of the system reliability function and its use in optimization-based approaches for designing optimal sensor networks.     

基于词法特征的恶意域名快速检测算法

针对互联网中恶意域名攻击事件频发，现有域名检测方法实时性不强的问题，提出一种基于词法特征的恶意域名快速检测算法。该算法根据恶意域名的特点，首先将所有待测域名按照长度进行正则化处理后赋予权值；然后利用聚类算法将待测域名划分成多个小组，并利用改进的堆排序算法按照组内权值总和计算各域名小组优先级，根据优先级降序依次计算各域名小组中每一域名与黑名单上域名之间的编辑距离；最后依据编辑距离值快速判定恶意域名。算法运行结果表明，基于词法特征的恶意域名快速检测算法与单一使用域名语义和单一使用域名词法的恶意域名检测算法相比，准确率分别提高1.7%与2.5%，检测速率分别提高13.9%与6.8%，具有更高的准确率和实时性。     

一种北斗联合低轨星座的导航增强方法研究

单纯依靠北斗导航系统提供定位导航授时服务,存在卫星信号落地功率低、易受遮蔽和阻断的不足。针对此问题,研究了一种北斗联合低轨星座实现导航增强的系统架构;提出了一种新的适应严重遮蔽或干扰条件下,基于到达时间(TOA)和到达频率(FOA)联合观测的定位解算算法;对高中低轨混合星座条件下的覆盖特性和精度衰减因子进行了仿真分析。分析结果表明,用户可见星数平均增加了64.2%,位置精度衰减因子(PDOP)平均改善了28.7%。研究结果可为下一代北斗的论证设计与研制建设提供参考借鉴。     

基于滑模的运载器主动段俯仰通道姿控系统设计

与传统比例-积分-微分（PID）控制方法相比，滑模控制（SMC）方法可以比较容易地将不确定性纳入控制器设计中，从而增强系统的鲁棒性。探索了SMC技术在运载器主动段姿态控制中的工程应用，首先通过分析基于趋近律的SMC系统，提出了降低不连续切换项系数的需求，然后研究了基于干扰上界的SMC方法。三通道小偏差仿真结果验证了两种方法的控制效果，表明第2种控制器的鲁棒性更好，稳态误差小，同时发动机喷管摆角需求较小。