纳米聚N-异丙基丙烯酰胺微凝胶的光引发聚合

选择具有温敏性的高分子单体N－异丙基丙烯酰胺（N－isopropylacrylamide，NIPAM）为主单体，N，N′－亚甲基双丙烯酰胺（methylenebisacrylamide，MBA）为交联剂，运用光引发无皂乳液聚合的方法合成出粒径小于100nm的高分子微凝胶，并研究了在改变体系组成和条件时微凝胶粒径的变化。结果显示，在乳化剂临界胶束浓度以下，随着乳化剂浓度的提高，微凝胶粒子的粒径不断关小且趋向稳定；相比于热引发，产生的微凝胶具有较高的单分散性而且粒径较小。     

用废旧橡胶生产精细胶粉的空气涡轮制冷低温粉碎法

利用先进的空气涡轮制冷系统，在低温条件下，将废旧橡胶进行冷冻，粉碎，制成60目以上细度的精细胶粉，此法简称ATCG法，它的冷冻能耗成本仅为国际上通用的液氮法的十分之一，整个工艺过程不产生二次污染，为精细胶粉的制取开辟了一条新途径。     

Separation of di- and tripeptides with solvent extraction and an emulsion liquid membrane

The extraction equilibria of various di- and tripeptides with di-2-ethylhexylphosphoric acid (D2EHPA) were studied at low pH values. The complex extracted to organic phase consisted of one molecule of peptide and two molecules of D2EHPA dimer. The extraction constants of the peptides correlated well with the distribution coefficients of peptides between 1-octanol and water, which is a measure of hydrophobicity. The permeation rates of peptides through an emulsion liquid membrane were examined by using D2EHPA as a carrier, Span 80 as an emulsifier and kerosene as a diluent. The rates varied considerably with peptide type, depending upon the hydrophobicity.     

抗坏血酸对核乳胶性能的影响

文章介绍抗坏血酸对核乳胶灵敏度、灰雾密度及潜影衰退性能的影响，并与日本富士ＥＴ－７Ｂ型乳胶的潜影稳定性能在不同温度和相对湿度条件下作相应比较。     

用二甲基二氯硅烷水解物代替混合环体生产107甲基室温硫化硅橡胶

分析了１０７甲基室温硫化硅橡胶生产中造成粘度波动和收率较低的因素，通过改变原料，用二甲基二氯硅烷水解物代替甲基混合环体，提高了产品收率、降低了成本，粘度也易于控制     

马来酸酐在乙丙橡胶上的接枝共聚

马来酸酐在乙丙橡胶上的接枝共聚,用过氧化苯甲酰为引发剂的效果优于偶氮二异丁腈。研究了温度、马来酸酐用量和引发剂用量等对接枝率的影响。用红外光谱和薄层色谱证明了接枝物的存在。用接触角技术测定了接枝物的表面性能。     

乳化炸药的高温化学发泡

文中在阐述ＮＨ４ＮＯ３－ＮａＮＯ２－Ｈ２Ｏ发泡体系的发泡机制的基础上，推导出了就获得较低的反应速率ｒＲ和气体生成量ｎ的高ｐＨ值对高温的平衡关系，从而提出了高温发泡技术。     

Stabilization of bioethanol recovery with silicone rubber‐coated ethanol‐permselective silicalite membranes by controlling the pH of acidic feed solution

In order to produce highly concentrated bioethanol by pervaporation using an ethanol‐permselective silicalite membrane, techniques to suppress adsorption of succinic acid, which is a chief by‐product of ethanol fermentation and causes the deterioration in pervaporation performance, onto the silicalite crystals was investigated. The amount adsorbed increased as the pH of the aqueous succinic acid solution decreased. The pervaporation performance also decreased with decreasing pH when the ternary mixtures of ethanol/water/succinic acid were separated. Using silicalite membranes individually coated with two types of silicone rubber, pervaporation performance was significantly improved in the pH range of 5 to 7, when compared with that of non‐coated silicalite membranes in ternary mixtures of ethanol/water/succinic acid. Moreover, when using a silicalite membrane double‐coated with the two types of silicone rubber, pervaporation performance was stabilized at lower pH values. In the separation of bioethanol by pervaporation using the double‐coated silicalite membrane, removal of accumulated substances having an ultraviolet absorption maximum at approximately 260 nm from the fermentation broth proved to be vital for efficient pervaporation. Copyright © 2005 Society of Chemical Industry     

浮体门设计的探索与实践

水电站泄水道破坏修复工程,是一项风险高、难度大、前景广阔的系统工程。刘家峡水电站泄水道2号孔破坏修复的关键,是采用人工深水软导向浮体闸门封堵孔口,形成门后洞内旱地施工条件;龚嘴水电站10号冲砂底孔破坏修复的关键,增设浮体闸门采用自动潜行式浮体闸门封堵孔口,形成门后洞内旱地施工条件;哈萨克斯坦CHARDARA水电站SYNAS项目泄水底孔修复的关键,采用分次降水安装浮体闸门侧支承的方法,挡住引水发电机组的下游尾水,在泄水道进口检修门和流道出口之间形成门旱地施工。此3项泄水道修复工程在行业内没有先例,难度很大。整体方案具有创新性,并且均已高质量竣工并投入正常运行。     

坨五站中间乳化层快速增长原因及治理方案

胜利采油厂坨五站高含水(95％)原油化学预脱水中，二级沉降罐内油水相之间的中间乳化层增长迅速，引起了一系列问题。现场调查和大量室内测试结果表明，产生这一现象的原因有：油溶性破乳剂WD-1加入点不合理。有2／3的含水原油在通过油水分离器之后才与破乳剂混合；二级沉降罐进油口伸入油相内，油流的冲击达不到中间层；WD-1对坨五站混合原油中的稠油破乳脱水性能欠佳，不能适应坨五站混合原油组成和含水的变化。针对上述各种原因筛选出了性能更好的一种破乳剂1916。根据确定的几种原因采取了相应的措施：将破乳剂加入点改在3个并联油水分离器之前；将二级沉降罐的进油口移到水相内；改用筛选出的破乳剂1916，结果使中间乳化层的增长受到了抑制。图2表4参2。