Microwave plasma synthesis of TiN and ZrN nanopowders

This work demonstrates that TiN and ZrN nanopowders can be prepared by microwave plasma synthesis method. The effects of flow rate of plasma forming gas, flow rate of carrier gas and feeding rate of precursor raw material to the average particle size were studied. The TiN and ZrN nanopowders were characterized by means of transmission electron microscopy (TEM) and X-ray diffraction (XRD).     

Effect of epitaxial realignment on the leakage behavior of arsenic-implanted,as-deposited polycrystalline Si-on-single crystal Si diodes

When dopants are indiffused from a heavily implanted polycrystalline silicon film deposited on a silicon substrate, high thermal budget annealing can cause the interfacial “native” oxide at the polycrystalline silicon-single crystal silicon interface to break up into oxide clusters, causing epitaxial realignment of the polycrystalline silicon layer with respect to the silicon substrate. Anomalous transient enhanced diffusion occurs during epitaxial realignment and this has adverse effects on the leakage characteristics of the shallow junctions formed in the silicon substrate using this technique. The degradation in the leakage current is mainly due to increased generation-recombination in the depletion region because of defect injection from the interface.     

99Tcm-MDP scintigraphy in high-voltage electrical burn patients

In high-voltage electrical burn injuries (> 1000 V), it is difficult to identify the site and extent of non-viable deep tissue damage for debridement to avoid further tissue injury from wound infection and the risk of sepsis. This prospective study was designed to evaluate the usefulness of 99Tcm-methylene di-phosphonate (99Tcm-MDP) scintigraphy in detecting the extent of tissue injury and determining the level of amputation required for electrical burn patients. Over a 5 year period, 33 high-voltage electrical burn patients were studied. Blood flow and blood pool studies revealed absent perfusion in 37 limbs, all of which eventually were amputated. In addition to a routine three-phase bone scan, images were obtained at 30-60 min (early images) to evaluate whether soft tissue injury could be detected better at that time. For comparison of the detection rate from the early images and bone (delayed) images, 164 corresponding spot views of both images were reviewed. Eighty-three and 125 tissue necrotic lesions were demonstrated by the early images and bone images respectively. All of the 83 lesions found by the early images were more clearly identified by the bone images. All but one of the 125 lesions underwent surgical debridement or amputation. We concluded that the blood flow and blood pool images correlated well with the level of amputation required. The site and extent of tissue necrotic lesions can be clearly identified on 99Tcm-MDP bone scans. Because the early images were less sensitive in detecting tissue necrosis, we suggest that early imaging is not necessary.     

A unified group technology implementation using the backpropagation learning rule of neural networks

Two engineering problems in implementing Group Technology are part family formation and part classification. Regardless of the approach adopted for the formation and classification, a critical problem is how to maintain consistency. The consistency problem can be addressed most effectively if the formation and classification is a single procedure rather than two separate procedures. A feedforward neural network using the Backpropagation learning rule is adopted to automatically generate part families during the part classification process. The spontaneous generalization capability of the neural network is utilized in classifying the parts into the families and creating new families if necessary. A heuristic algorithm using the neural network is described with an illustrative example.     

Kinetics of AuSn4 migration in lead-free solders

The relatively fast diffusion of Au atoms in eutectic PbSn matrix is considered one of the contributing factors to the Au embrittlement problem. In this study, we further investigated the Au embrittlement problem in high-Sn solders. Experimentally, Sn3.5Ag (wt.%) spheres with 500-μm diameter were soldered over the Au/Ni soldering pads. It was found that some of the AuSn₄ needles that formed after reflow inside the solder migrated back to the solder/pad interface during thermal aging. However, the migration kinetics in high-Sn solders was slower compared to that in eutectic PbSn. The difference in migration kinetics of AuSn₄ in eutectic PbSn and SnAg was ascribed to the difference in the magnitudes of the Au flux and the Ni flux. In eutectic PbSn, the Au flux was much greater than that of the Ni flux, and the Au and Ni flux were in the same order of magnitude in eutectic SnAg. The relative magnitude of the Au and Ni flux changed in eutectic PbSn and SnAg because the homologous temperatures of PbSn and SnAg were different.     

高速公路礫石隧道設計之探討

礫石隧道之設計施工與岩石隧道有著明顯的不同,如在岩體分類方面無法使用岩石隧道常用的南非CSIR-RMR及挪威Barton-Q值之定量評估方法.另其工址調查也常因粒徑及採樣不易,無法進行室内試驗而影響力學參數的評估.近年來雖有部分礫石隧道個案完成,然而礫石隧道所估比例仍屬稀少,因此礫石隧道之施工經驗仍較缺乏,對於高速公路等級而言更是首例.由於礫石隧道地質之特殊,致隧道設計之前應對台灣礫石地層之成因及類型等有基本認識,充分瞭解礫石層之地質特性與力學性質,才能進一步探討礫石隧道之相關課題.首先針對上述因素加以探討,然後以一礫石隧道設計實例來說明設計之實際考量及過程,最後進行隧道之支撐設計及數值模擬比較,俾供後續類似地層設計之參考.     

DETECTOR: A knowledge-based system for injection molding diagnostics

A knowledge-based system (KBS) for diagnosis of multiple defects in injection molding is presented. The general scheme for knowledge representation based on fuzzy set theory has been shown useful in representing inexact and incomplete information for developing the KBS. An optimality criterion is created for selecting a simple and best cover to explain the given problem. An efficient search algorithm for finding such cover is also discussed.     

Solving the bi-objective personnel assignment problem using particle swarm optimization

A particle swarm optimization (PSO) algorithm combined with the random-key (RK) encoding scheme (named as PSORK) for solving a bi-objective personnel assignment problem (BOPAP) is presented. The main contribution of this work is to improve the f₁_f₂ heuristic algorithm which was proposed by Huang et al. [3]. The objective of the f₁_f₂ heuristic algorithm is to get a satisfaction level (SL) value which is satisfied to the bi-objective values f₁, and f₂ for the personnel assignment problem. In this paper, PSORK algorithm searches the solution of BOPAP space thoroughly. The experimental results show that the solution quality of BOPAP based on the proposed method is far better than that of the f₁_f₂ heuristic algorithm.     

Physical properties of transition to chaos in RF-driven Josephson junction analog

An analog circuit is used to investigate the behavior of the transition to chaos in the rf-driven Josephson junction under the variation of excitation amplitude and frequency with McCumber parameter >1. A series of transitions is observed, including a hysteretic jump, symmetry breaking, period doubling, and intermittency prior to chaos, and the transition boundaries are given in a state diagram in the vs. parameter space. Thus, the sequence of transitions to chaos can be inferred from this diagram. Based on these results, the harmonic balance method and Floquet theory are applied to study the instability of the transition series. It is suggested that all these transitions to chaos can be explained as parametric excitations. In addition, the transition boundaries in the state diagram can be satisfactorily computed from the conditions with a Floquet multiplier =±1.     

Conductivity enhancement in transparetn ZnO films via Al-dopping produced by CW-CO2 laser-induced evaporation

Highly conductive transparent aluminium-doped ZnO (ZnO:A1) films were successfully deposited by CW-CO₂ laser-induced evaporation. Optimisation of evaporation parameters was based on laser power, substrate temperature, O₂ partial pressure in the vacuum chamber and amount of Al in the ZnO source pellet. ZnO:A1 films with an electrical resistivity as low as 6.6 × 10⁻²Ω·cm and an optical transmission of 80% at 500nm were obtained at laser power of 15 W, substrate temperature of about 200°C, O₂ partial pressure of 6—7 × 10⁻⁴ Torr and 5wt.% Al. Conductivity of ZnO films can be increased one order via Al-doping in ZnO films. The films obtained by laser-induced evaporation have compared quite favorably with the high quality films obtained by sputtering.