Analysis on Ground Surface Deformation and Influence of Construction Parameters Caused by Two Different Shield Machines in Double-tube Tunnelling北大核心CSCD

Based on a shield-driven running tunnel project of Hangzhou Metro Line 2, this paper carries out field measuring of the ground surface deformation caused by two different shield machines in double-tube tunnelling in soft soil areas, obtains the laws of the surface deformation caused by shield-driven double-tube tunnelling and verifies the applicability of the modified Peck formula to double-tube tunnelling. The results show that in soft soil areas the impacts on ground surface deformation caused by different shield construction parameters in the previously and subsequently excavated tunnels are different, while the surface deformation changes sharply before and after the shield machine passing through the cutting face, and a rebound phenomenon occurs when the shield tail passes through the cutting face due to the influence of the grouting; The cutterhead torque of the shield machine in soft soil areas can be composed of five calculation factors, and the calculation results are in good agreement with the measured values. The larger the opening rate of the shield cutterhead is, the larger the average torque value will be, the higher the percentage of large ground loss rate will be, and the larger the maximum ground surface settlement will be; The ratio of cutterhead torque T to mucking volume per ring Q is used as the control parameter for analyzing the ground surface settlement, and a certain positive correlation between the ratio and the surface settlement value is determined, the smaller the cutterhead opening rate is, the more accurate the fitting results will be. © 2022, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Correcting injection pressure maladjustments to reduce NOX emissions by marine diesel engines

Emissions from the exhausts of marine diesel engines comprises several different gases including NO_X. These are currently regulated at the international level under Regulation 13 of ANNEX VI of MARPOL 73/78, but this regulation only applies to new engines and is based on bench tests, for only a single engine designated the “parent engine”. Here, the need to take measurements from across their whole range and once in operation on board a vessel is examined. This would not only improve assessment of new equipment against the current regulation, but would also detect defects in the functioning of the engine.     

Implementation of discharging/charging current sensorless state-of-charge estimator reflecting cell-to-cell variations in lithium-ion series battery packs

This paper offers novel insights to the design and implementation of an innovative state-of-charge (SOC) estimator for the lithium-ion (Li-Ion) series battery pack. The most interesting feature of this approach is that it can utilize information from each filtered terminal voltage of the Li-Ion cells connected in series for SOC estimation of the battery pack. Without actual sensing each discharging/charging current (DCC) applied to the Li-Ion cells, it is possible to extract each DCC estimation from the corresponding filtered terminal voltages with an equivalent electrical circuit model (EECM) identification of all Li-Ion cells in the battery pack. There are two advantages to SOC estimation of the battery pack with this approach. First, the proposal can be implemented simply and effectively, reducing the computational steps required for SOC estimation. By reducing computational steps, the proposal is expected to be more cost-effective. Second, the approach guarantees an improved SOC performance, even if the battery pack results in inevitable cell-to-cell variation among Li-Ion cells. Accordingly, there are fewer differences to previously estimated DCCs among Li-Ion cells. Specifically, all values from the estimated DCCs are properly compensated for by simultaneous parameter modification according to each cell’s electrochemical characteristics. Experimental results clearly demonstrate that our DCC sensorless SOC estimator provides robust SOC performance for the battery pack. This approach considered an experimental battery pack (12S1P) connected in series using 2.6 Ah LiCoO2 cells produced by Samsung SDI.     

Experimental study on a model azimuthing podded propulsor in ice

The objective of this study was to investigate the performance of a model azimuthing podded propulsor in ice-covered water. Model tests were carried out with two different depths of cut into the ice (15 and 35 mm), two different ice conditions (presawn and pack ice conditions), and four different azimuthing angles. The depth of cut is the maximum penetration depth of the propeller blade into the ice block. The 0.3-m-diameter model propeller was operated in a continuous ice milling condition. Ice loads were measured by several sensors which were installed in various positions on the model. Six one-axis pancake-style load cells on the top of the model measured the global loads and two six-component dynamometers were installed on the shaft to measure the shaft loads. One six-component dynamometer was attached to the one of the propeller blades inside the hub to measure the blade loads. The pod unit and propeller performance in ice are presented. Ice-related loads, which were obtained when the blade was inside the ice block, are introduced and discussed. During the propeller–ice interaction, a blade can experience the path generated by the previous blade, which is called the shadowing effect. The effects of shadowing, depth of cut, azimuthing angle, and advance coefficient on propulsor performance are presented and discussed.     

Improving pollutant emissions in diesel engines for heavy-duty transportation using retarded intake valve closing strategies

A combined theoretical and experimental study has been carried out to determine the real potential of reducing pollutant emissions in a HD diesel engine by means of retarding the intake valve closing. The effects produced by this alteration of the basic operation cycle have been examined by a preliminary modelling study, and from the obtained results, a modified camshaft was manufactured with a delayed intake valve closing of 60 crank angle degrees. Single-cylinder engine tests were carried out with this modified camshaft, and the emissions and fuel consumption were recorded. The results showed that the retarded intake valve closing can enhance the premixed combustion phase, and thus simultaneously reduce soot and NOx emissions. Moreover, the combustion process attained is extremely tolerant to exhaust gas recirculation, and by adoption of this measure, Euro-5 emissions limits can be achieved at the tested conditions without after-treatment.     

Trip generation of vulnerable populations in three Canadian cities: a spatial ordered probit approach

This paper provides an analysis of trip generation of three vulnerable groups: single-parent families, low income households, and the elderly. It compares the mobility of these groups to that of the general population in three Canadian urban areas of Hamilton, Montreal and Toronto, based on data from large-sample metropolitan transport surveys. An ordered probit model with spatially expanded coefficients is used for the analysis. Spatial expansion shows that there are spatial mobility trends for elderly populations and low-income populations even after socio-economic attributes are accounted for. Such spatial differences are not generally found for single parent families. This novel spatial analysis provides clues as to where vulnerable populations may experience greater degrees of social exclusion. It provides information to help prioritize transportation infrastructure projects or other social programs to take into account the needs of vulnerable populations with the lowest levels of mobility.     

Assessment of diesel combustion noise overall level in transient operation

Combustion noise in passenger cars powered with direct injection (DI) diesel engines is frequently the main reason why end-users are reluctant to drive this type of vehicle. Thus, the great potential of diesel engines for environment preservation — due to their lower CO₂ emissions — could be missed. This situation worsens with the current design trends (engine downsizing) and the emerging new diesel combustion concepts (Homogeneous Charge Compression Ignition-HCCI, Premixed Charge Compression Ignition-PCCI, etc.), which are intrinsically noisy. This negative feature can be even more critical in transient operation due to the contribution of the temporal changes of both source and transmission path on engine noise. Therefore, combustion noise must be considered as an additional essential factor in engine development, together with performance, emissions and driveability. Thus, suitable evaluation procedures that can be integrated into the global engine development process in a timely and cost-effective manner are imperative. Regarding the evaluation procedures, most of the work available in the literature addressed combustion noise at steady operation. To surpass this limitation, two possible approaches — adapted from the classical and multiple regression methods — for the overall level assessment of combustion noise in transient conditions are evaluated in this paper.     

Adapting the light · biomass (BZI) models of phytoplankton primary production to shallow marine ecosystems

Several authors have reported a strong linear relationship between daily phytoplankton production and the product of chlorophyll biomass, photic depth, and incident irradiance for a variety of estuaries. This “light · biomass” (BZ_pI_o) formulation has been proposed as an alternative to traditional mechanistic approaches for computing phytoplankton production in numerical estuarine models. One limitation to their application in shallow systems is that the BZ_pI_o models have been developed in relatively deep estuaries where light does not reach the bottom. We propose a nonlinear correction factor to adapt the BZ_pI_o relationship to shallow systems where light does reach the bottom. Our function takes into account variations in incident irradiance, attenuation coefficient for light, photosynthetic efficiency, and maximum rate of photosynthesis. A series of correction polynomials are proposed for various ranges of incident irradiance, and are integrated into a single multiple polynomial which applies across all irradiance levels. Our new correction factor was tested against a ¹⁴C-based productivity dataset from shallow stations in Narragansett Bay, RI and an O₂-based dataset from shallow (1.1 m) lagoon mesocosms at the University of Rhode Island. Results showed that our polynomials accurately correct BZ_pI_o-predicted rates of production in shallow water columns. Application of our correction factor to a series of shallow water productivity datasets from the literature together with theoretical calculations show how significant the shallow water correction can be, especially in very shallow water columns with low turbidity.     

Biologically induced differences in erodibility and aggregation of subtidal and intertidal sediments: a possible cause for seasonal changes in sediment deposition

This study was carried out to describe the difference in erodibility and aggregation in a tidal basin including both subtidal and intertidal study sites and to use these results to explain the shifting erosion/deposition cycles at the sites. Erosion thresholds, erosion rates and settling velocities of the eroded material were measured at a mudflat transect and at sediment cores taken from a nearby tidal channel during surveys made in May 2000 and March 2002. Surface samples were analysed for grain-size, chl. a content, faecal pellet content, dry bulk density and organic content. Additionally, surface samples were taken at eight occasions in the period January 2002 to May 2003 from shallow tidal channels in the area. These samples were analysed for mud content and showed that major shifts in sediment distribution occurred in the period. The erodibility of the mudflat was generally high due to pelletization by the mudsnail Hydrobia ulvae but close to the salt marsh much lower erodibility was found, probably due to stabilisation by microphytobenthos. In contrast, the erodibility of the channel bed seemed to be very little influenced by biological activity and the relatively low erodibility found here was caused by physical characteristics of the sediment. The sediment eroded from the mudflat was generally strongly pelletized and showed high settling velocities whereas less aggregation and lower settling velocities were found for the channel bed sediments. Temporal variations of the mudflat stability and hydrodynamics resulted in temporal variations of deposition and erosion and the changing stability at the mudflat is likely to be one of the main reasons for a general transport of fine-grained sediment from the mudflat to the channel in the cold seasons and vice versa during the rest of the year.