固定化脂肪酶选择性水解废弃鱼油富集DHA和EPA甘油酯

以鱼油下脚料为原料．以固定化Geotrichum sp．脂肪酶为催化剂,选择性水解粗鱼油,使目标脂肪酸EPA和DHA富集于甘油骨架上,显著提高了甘油酯中EPA和DHA的质量分数。通过单因素试验和响应面分析得出最佳水解条件：2g粗鱼油,2．5g水,221．3U脂肪酶,30℃,反应11．7h。最佳条件下的水解度为42．1％。EPA和DHA质量分数分别为7．8％和41．1％。经过二次水解后,水解度提高到45．9％,EPA和DHA质量分数分别提高到8．5％和42％。与初始鱼油相比,分别提高了2倍和2．2倍。     

Geotrichum sp．SYBC WU-3脂肪酶的双水相萃取和酶学性质

初步研究双水相体系对Geotrichum sp．SYBC WU-3脂肪酶的萃取分离效果,选用PEC4000／NaH2 PO4作为戍相系统进行系统研究,考察影响脂肪酶萃取的各种因素（如PEG相对分子质量及质量分数、NaH2PO4质量浓度、pH）,并采用正交实验进一步优化实验条件,确定双水相萃取体系为PEG质量分数为30％、NaH2PO4质量分数为20％、体系pH为6,在此条件下Geotrichum sp．SYBC WU-3脂肪酶经硫酸铵沉淀和双水相萃取两步纯化的纯化倍数达到最大,较Geotrichum sp．SYBC WU-3脂肪酶粗酶纯化了22倍。Geotrichum sp．SYBC WU-3脂肪酶纯酶为低温碱性脂肪酶,最适反应温度为15oC,最适pH为9．5,相对分子质量为3．58×10^4。     

有机相脂肪酶催化酮基各芬的立体选择性酯化

从５种脂肪酶中筛选出了具有较高催化活性和对映体选择性的脂肪酶Ｎｏｖｏｚｙｍ ４３５。进一步探讨了酶浓度、底物结构、底物浓度等因素对脂肪酶拆分酮基布洛芬（Ｋｅｔｏｐｒｏｆｅｎ）的影响。结果表明,以１０ｍＬ除水环己烷为反应介质,酶浓度为５ｍｇ／ｍＬ,Ｎｏｖｏｚｙｍ ４３５催化６．７ｍｍｏｌ／Ｌ Ｋｅｔｏｐｒｏｆｅｎ与２６．８ｍｍｏｌ／Ｌ丙醇进行酯化反应,反应３０ｈ,转化率为６８％时,Ｓ－酮基布洛芬对映     

利用麻风树油驯化筛选高活性脂肪酶产生菌及其催化酯化反应

以1株分解麻风树油的脂肪酶产生菌Pseudomonas sp. LP-1为出发菌株, 通过麻疯树油定向驯化筛选获得1株酶活较高且产酶稳定的菌株P. sp. X-2-45, 其水解酶活为29.79 U/mL, 比原始菌株提高了288%。对P. sp. X-2-45生长与产酶特征、对植物油脂水解能力及在有机相中催化脂肪酸和有机醇间的酯化反应研究发现, 该菌株生长速率和产酶速率明显加快, 培养30 h时生物量和酶活达到最大, 稳定期延长, 培养过程中脂肪酶在培养基中的稳定性提高。以麻疯树油诱导合成的P. sp. X-2-45脂肪酶对麻疯树油的水解能力比原始菌株提高了378%, 说明采用麻风树油定向驯化可提高脂肪酶对相应底物的水解能力。X-2-45脂肪酶可以催化月桂酸与正丁醇、正辛醇、月桂醇和丙三醇之间, 棕榈酸、硬脂酸与甲醇、正辛醇、月桂醇和丙三醇之间, 油酸与甲醇、正丁醇、正辛醇、月桂醇和丙三醇之间发生酯化反应。     

有机相脂肪酶催化酮基布洛芬的立体选择性酯化*

从５种脂肪酸中筛选出了具有较高催化活性和对映体选择性的脂肪酶Ｎｏｖｏｚｙｍ ４３５。进一步探讨了酶浓度、底物结构、底物浓度等因素对脂肪酶拆分酮基布洛芬（Ｋｅｔｏｐｒｏｆｅｎ）的影响。结果表明,以１０ｍＬ除水环己烷为反应介质,酶浓度为 ５ｍｇ／ ｍＬ, Ｎｏｖｏｚｙｍ ４３５催化 ６．７ｍｍｏｌ／ Ｌ Ｋｅｔｏｐｒｏｆｅｎ与２６．８ｍｍｏｌ／ Ｌ丙醇进行酯化反应,反应 ３０ｈ,转化率为 ６８％时,Ｓ－酮基布洛芬对映作过剩值可达 ９２％。     

非水介质中脂肪酶催化亚油酸油醇酯合成的研究

利用实验室自制及购买的几种脂肪酶制剂催化的酯化反应来制备亚油酸油醇酯,其中本实验室制备的丝孢酵母脂肪酸酯化效果最好,作为进一步研究的实验用酶。以正己烷为反应溶剂,在微水系统中对影响亚油酸油醉酯合成的各种因素进行了研究,确定酯化反应合成的最适温度为３５℃,０～１００℃反应１０ｈ的酯化率均可达到９０％,最适酯化ｐＨ为８．０,最适底物浓度为０．２５ｍｏｌ／Ｌ,最适水含量为０．０５％,在选用的１１种有机溶剂中,以环己烷的酯化率最高,二甲亚砜最低。     

脂肪酶的固定化及其性质研究

采用吸附与交联相结合的方法国定化脂肪酶,研究了脂肪酶固定化的工艺条件,并考察了固定化脂肪酶的催化性能和稳定性。试验结果表明,WA20树脂固定化脂肪酶的最适条件是：酶液pH7．0、给酶量300IU／g树脂、固定时间8h,所得固定化脂肪酶的活力约为165IU／g树脂;固定化酶稳定性较高,在冰箱内贮存6个月活力没有下降,操作半衰期约为750h,而未用戌二醛文联的固定化脂肪酶操作半衰期仅约290h;固定化脂肪酶催化橄榄油水解的最适条件是：PH8．0、温度55℃、底物浓度60％（V／V）、搅拌转速500r／m。     

脂肪酶催化有机硅化合物的生物转化

C.cylindracea脂肪酶可催化有机介质中有机硅醇与脂肪酸的酯化反应。微水有机介质比水-水不溶有机介质更有利于酶的反应,有机硅醇是比其碳结构类似物更好的酰基受体。对不同有机硅醇底物,当其空间障碍大时,不利于酶催化酯化反应,对不同脂肪酸底物,有机硅醇未影响该脂肪酶的脂肪酸底物特异性。     

有机溶剂中固定化脂肪酶催化硅醇的酯化反应

固定化Mucor miehei脂肪酶可催化有机硅醇和脂肪酸的酯化反应．对固定化酶用量、脂肪酸链长、不同有机硅醇底物、有机溶剂极性和水含量等影响因素进行了初步研究．     

非水相脂肪酶催化有机硅醇的酯化反应

非水相酶催化是酶工程研究热点之一。本文介绍了来自Ｃ．ｃｙｌｉｎｄｒａｃｅａ的脂肪酶催化有机硅醇和脂肪酸的酯化反应。该酶可催化有机硅醇与脂肪酸的酯化反应,并对不同链长的脂肪酸底物、有机溶剂极性及水含量等进行了初步研究。     

低温脂肪酶产生菌的筛选、产酶发酵及粗酶性质研究

利用含有Tween 80的琼脂平板和摇瓶发酵法,从若尔盖高原土壤中筛选产脂肪酶菌株.通过菌落形态和菌体特征观察初步对菌种进行鉴定,得到一株产低温脂肪酶的适冷菌Pseudomonassp.DL-B,并设计正交试验对该菌株的产酶发酵培养条件进行了优化.摇瓶实验表明,该菌株最适产酶发酵培养基为:蔗糖10 g/L,蛋白胨20 ...     

产脂肪酶菌株C7828-5的筛选、鉴定以及产酶条件的优化

以花生油为唯一碳源,从海口市各地被油脂污染土样中分离筛选出1株中温碱性脂肪酶菌株C7828-5。形态学、生理生化特征和分子生物学鉴定结果表明,该菌株为铜绿假单胞菌(Pseudomonas aeruginosa)。该菌所产脂肪酶的最适温度为37℃,最适pH为8.0。优化了菌株的产酶条件,最适产酶培养基(g/L)为:蔗糖5、牛肉膏20、(NH_4)_2SO_41、MgSO_4·7H_2O 0.5、CaCl_20.5,聚乙烯醇花生油乳化液120 mL,发酵72 h,获得高达8.08 U/mL的脂肪酶表达量。     

Enrichment of polyunsaturated fatty acids from tuna oil using immobilized Pseudomonas fluorescens lipase

Immobilized Pseudomonas fluorescens lipase enzyme was used to enrich the important polyunsaturated fatty acid (PUFA), docosahexaenoic acid (DHA) and eicosapentaenoic acid (EPA) from tuna oil. Hydrolysis, esterification, and transesterification reactions were studied in detail to find out the fractionation pattern of DHA and EPA during these processes due to preferential selectivity for or against these PUFA. Hydrolysis with P. fluorescens biotype I lipase with stoichiometric amount of water content gave more than 80% of DHA and EPA in the free fatty acid (FFA) form after around 60% of hydrolysis. After some preferential specificity during the early stages of hydrolysis, P. fluorescens lipase exhibits nonselective characteristics on extended hydrolysis. Esterification of FFA extracted from the completely hydrolyzed mixture of tuna oil was found to be better with long chain fatty alcohol like octanol which lead to good enrichment (44.5% for DHA and 11.3% for EPA) and yields of the PUFA in the FFA form. Transesterification (ethanolysis) with immobilized P. fluorescens lipase enzyme resulted in good enrichment and recovery of DHA and EPA in the glyceride mixture. After around 60% of ester synthesis, 74% of (DHA + EPA) enrichment was achieved with yields of more than 90% in the glyceride mixture.     

Concentrates of DHA from fish oil by selective esterification of cholesterol by immobilized isoforms of lipase from Candida rugosa

Two lipases (Lip A and Lip B), were purified from a commercial lipase preparation produced by Candida rugosa and partially characterized. The purified lipases were immobilized on Duolite A 568 and used in the selective esterification of cholesterol with free fatty acids from sardine fish oil. The results showed that Lip A and Lip B preferentially esterified saturated and monounsaturated fatty acids allowing a 3.4-fold (Lip B, 24 h) and 4-fold (Lip A, 10 h) enrichment of docosahexaenoic acid in the remaining free fatty acid fraction. Selectivity towards eicosapentaenoic acid was less pronounced. By this selective esterification docosahexaenoic acid was concentrated from 7.4 to 32% with a recovery of 95% of its initial content in sardine fish oil.     

Fatty acid preference of mycelium-bound lipase from a locally isolated strain of <Emphasis Type="Italic">Geotrichum candidum</Emphasis>

Mycelium-bound lipase (MBL) was prepared using a strain of Geotrichum candidum isolated from local soil. At the time of maximum lipase activity (54 h), the mycelia to which the lipase was bound were harvested by filtration and centrifugation. Dry MBL was prepared by lyophilizing the mycelia obtained. The yield of MBL was 3.66 g/l with a protein content of 44.11 mg/g. The lipase activity and specific lipase activity were 22.59 and 510 U/g protein, respectively. The moisture content of the MBL was 3.85%. The activity of free (extracellular) lipase in the culture supernatant (after removal of mycelia) was less than 0.2 U/ml. The MBL showed selectivity for oleic acid over palmitic acid during hydrolysis of palm olein, indicating that the lipase from G. candidum displayed high substrate selectivity for unsaturated fatty acid containing a cis-9 double bond, even in crude form. This unique specificity of MBL could be a direct, simple and inexpensive way in the fats and oil industry for the selective hydrolysis or transesterification of cis-9 fatty acid residues in natural triacylglycerols.     

渗透压调控对裂殖壶菌发酵产DHA的影响

考察了不同渗透胁迫(0、10、20、30和40 g/L NaCl)对裂殖壶菌HX-308发酵产DHA及脂肪酸构成的影响。结果表明:20 g/L NaCl最有利于裂殖壶菌生长和DHA积累,生物量、总脂肪酸含量、DHA产量及DHA占生物量的比值分别为73 g/L、10.7 g/L、5.0 g/L和68 mg/g,并且DHA在总脂肪酸中所占百分比最高,为45.2%。此外,在低渗透压(10 g/L NaCl)条件下,添加40 mmol/L甘氨酸甜菜碱,DHA产量与未添加相比提高了28.21%;在高渗透压(40 g/L NaCl)条件下添加40 mmol/L海藻糖,DHA产量提高了46.84%;表明添加适量的外源相容性溶质能有效地促进裂殖壶菌积累DHA。     

白地霉ch-3脂肪酶Ⅰ基因在大肠杆菌中的表达

构建了白地霉脂肪酶Ⅰ的基因工程菌,为进一步进行蛋白质工程改造和脂肪酶应用奠定了基础。从新疆昌吉市油脂化工厂含油冻土中分离得到1株低温脂肪酶产生菌-白地霉ch-3。该菌发酵上清液中的脂肪酶最适作用温度为35℃,在0℃仍可保持66%的相对酶活力。应用PCR技术从白地霉ch-3基因组DNA中克隆得到脂肪酶Ⅰ基因lip1,将该基因与原核表达质粒载体pET-22b（＋）连接,构建重组质粒pETl-ip1,转化E.coliBL21（DE3）,酶切鉴定,筛选得到重组菌。十二烷基磺酸钠-聚丙希酰胺（SDS-PAGE）显示重组脂肪酶Ⅰ的相对分子质量约为5.8×10^4,酶活为2.73 U/mL,表明lip1基因的表达产物具有正常的生物学活性。白地霉ch-3脂肪酶Ⅰ基因lip1能够在大肠杆菌中有效地表达。     

Lipase specificity towards eicosapentaenoic acid and docosahexaenoic acid depends on substrate structure

The fatty acid specificity of five lipases towards eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA) was evaluated in the hydrolysis of fish oil, squid oil and a model system. The model system contained methyl esters of EPA, DHA and palmitic acid. All the investigated lipases discriminated against both EPA and DHA more in the model system than in the natural oils. Thus both EPA and DHA were more easily hydrolysed from a glyceride than from a methyl ester. In the model system, the lipase from Candida rugosa showed the highest discrimination against DHA, while the lipases from Pseudomonas fluorescens and Pseudomonas cepacia discriminated against EPA the most. In a glyceride, the fatty acid specificity of lipases towards EPA and DHA was affected by the positional distribution of the fatty acids and the glyceride structure due to the regiospecificity and triglyceride specificity of the lipase. In the oils, the Pseudomonas lipases also discriminated against EPA the most, while DHA was initially discriminated the most by the lipase from Thermomyces lanuginosus. However, after longer reaction times the enrichment of DHA in the glyceride fraction of the oils was greatest for the lipase from C. rugosa.     

L-抗坏血酸洛芬酯非水相酶促合成的动力学与热力学

对酶法合成L-抗坏血酸洛芬酯(芬维C酯)的反应动力学与热力学进行研究,确定了最有效的酶促反应环境。合成布洛芬维C酯的最优条件:转速200r/min,温度65℃,加酶量5%(以底物的质量分数计),底物浓度1mol/L,平衡所需时间66h,平衡时产物质量分数为19.07%;合成酮洛芬维C酯的最优条件:200r/min,60℃,加酶量7.5%,底物浓度600mmol/L,平衡时间132h,产物质量分数为10.63%;合成氟比洛芬维C酯的最优条件:200r/min,65℃,加酶量5%,底物浓度400mmol/L,平衡时间144h,产物质量分数为6.76%。对底物进行了比较,得到了各自的动力学与热力学参数。布洛芬米氏常数为0.101μmol/L,vmax=32.68μmol/(min.g),热力学平衡常数为0.166;酮洛芬的分别为0.144μmol/L,12.97μmol/(min.g),0.091;氟比洛芬的分别为0.185μmol/L,9.35μmol/(min.g),0.055。