Friction and Wear Behaviors of Ag/MoS2/G Composite in Different Atmospheres and at Different Temperatures

Silver-based composite with 15?vol% MoS₂ and with 5?vol% graphite was prepared by powder metallurgy method. The impacts of the counterface materials, atmosphere, and temperature on the tribological behavior of the composite were investigated. It was found that when sliding against brass less effective lubricating film formed, causing a higher friction and wear comparing with ASTM-1045 steel. With the increasing proportion of oxygen in the O₂/N₂ atmosphere, the wear rate and friction coefficient ascended slightly. At 200?°C, the combination lubrication of graphite, MoS₂, and Ag contributed to a low friction coefficient (0.07) and wear rate (6.56?×?10^?6?mm³/Nm). At 400?°C, graphite lost its lubricating role, while silver became excessively soft. Large amount of MoS₂ was oxidized into MoO_3, and the residual MoS₂ formed some island-like lubricating films. Severe adhesive wear occurred on the contact surface, which led to a high friction coefficient (0.25) and a great increase of the wear rate (23.2?×?10^?6?mm³/Nm). At 600?°C, a relatively low friction coefficient (0.1) was obtained because of the formation of high-temperature solid lubricants, (Ag₂Mo₄O₁₃ and Ag₂Mo₂O₇) and liquid Ag₂Mo₂O₇. However, the wear rate at 600?°C was the highest (32.6?×?10^?6?mm³/Nm) due to the thick transfer layer.     

Boric Acid Self-Lubrication of B2O3-Filled Polymer Composites

Utility of boric oxide particles in PTFE and epoxy composite materials, in sliding contact with stainless steel, is explored. Boric oxide filler can provide PTFE with a two-decade reduction in wear rate, to 10^?5 mm₃/N-m. With adequate ambient humidity reduced wear rate can be achieved without inducing counterface abrasion, and the friction of PTFE is further reduced slightly. In such environments, boric oxide fillers can also reduce friction coefficient of epoxy from μ>0.7 to as low as μ=0.07. This lubrication mechanism results from replenishment of lubricous boric acid lamellar solid provided to the sliding interface by reaction of boric oxide with ambient water. Maintenance of the lubricating effect depends upon a sufficient rate of boric acid formation, relative to subsequent removal by wear. It is demonstrated that this formation/removal balance is affected by relative humidity and volume fraction of boric oxide filler, as well as normal load and sliding speed.     

Microstructure and lubrication mechanism of multilayered MoS2/Sb2O3 thin films

Multilayered MoS₂/Sb₂O₃ thin films were prepared by pulsed laser deposition on steel substrates. A rotary multi-target holder was used to switch the laser targets for alternative growth of MoS₂ and Sb₂O₃ layers providing nanometers thickness. The tribological properties of the films were measured in dry and wet environments and the wear scars were observed using a scanning electron microscope. The multilayer films showed a much longer wear life than pure MoS₂ films in wet air tribotests. Focused ion beam and transmission electron microscopies were used to investigate the cross-sectional microstructures of wear scars. Lubricious MoS₂/Sb₂O₃ tribofilms were built up on wear scar surfaces, and produced low friction. Micro-cracks occurred along the interface between the tribofilm and the neighboring/topmost Sb₂O₃ underlayer, where the Sb₂O₃ layer effectively inhibited the crack propagation perpendicular to the interface. The orientation of MoS₂ crystals in as-deposited films was mostly random and friction-induced stress oriented the MoS₂ basal planes parallel to the surface. The reorientation was confined to the topmost MoS₂ layer and was not observed below the first intact Sb₂O₃ layer.     

Improving the Tribological Behavior of Graphite/Cu Matrix Self-Lubricating Composite Contact Strip by Electroplating Zn on Graphite

Studies to explore the nature of friction, and in particular thermally activated friction in macroscopic tribology, have lead to a series of experiments on thin coatings of molybdenum disulfide. Coatings of predominately molybdenum disulfide were selected for these experiments; five different coatings were used: MoS₂/Ni, MoS₂/Ti, MoS₂/Sb₂O₃, MoS₂/C/Sb₂O₃, and MoS₂/Au/Sb₂O₃. The temperatures were varied over a range from −80 °C to 180 °C. The friction coefficients tended to increase with decreasing temperature. Activation energies were estimated to be between 2 and 10 kJ/mol from data fitting with an Arrhenius function. Subsequent room temperature wear rate measurements of these films under dry nitrogen conditions at ambient temperature demonstrated that the steady-state wear behavior of these coatings varied dramatically over a range of K = 7 × 10⁻⁶ to 2 × 10⁻⁸ mm³/(Nm). It was further shown that an inverse relationship between wear rate and the sensitivity of friction coefficient with temperature exists. The highest wear-rate coatings showed nearly athermal friction behavior, while the most wear resistant coatings showed thermally activated behavior. Finally, it is hypothesized that thermally activated behavior in macroscopic tribology is reserved for systems with stable interfaces and ultra-low wear, and athermal behavior is characteristic to systems experiencing gross wear.     

Multi-environmental lubrication performance and lubrication mechanism of MoS2/Sb2O3/C composite films

MoS₂–Sb₂O₃–C composite films exhibit adaptive behavior, where surface chemistry changes with environment to maintain the good friction and wear characteristics. In previous work on nanocomposite coatings grown by PVD, this type of material was called a “chameleon” coating. Coatings used in this report were applied by burnishing mixed powders of MoS₂, Sb₂O₃ and graphite. The solid lubricant MoS₂ and graphite were selected to lubricate over a wide and complementary range including vacuum, dry air and humid air. Sb₂O₃ was used as a dopant because it acts synergistically with MoS₂, improving friction and wear properties. The MoS₂–Sb₂O₃–C composite films showed lower friction and longer wear life than either single component MoS₂ or C film in humid air. Very or even super low friction and long wear-life were observed in dry nitrogen and vacuum. The excellent tribological performance was verified and repeated in cycles between humid air and dry nitrogen. The formation of tribo-films at rubbing contacts was studied to identify the lubricating chemistry and microstructure, which varied with environmental conditions. Micro-Raman spectroscopy and Auger electron spectroscopy (AES) were used to determine surface chemistry, while scanning electron microscopy and transmission electron microscopy were used for microstructural analysis. The tribological improvement and lubrication mechanism of MoS₂–Sb₂O₃–C composite films were caused by enrichment of the active lubricant at the contact surface, alignment of the crystal orientation of the lubricant grains, and enrichment of the non lubricant materials below the surface. Sb₂O₃, which is not lubricious, was covered by the active lubricants (MoS₂ – dry, C – humid air). Clearly, the dynamics of friction during environmental cycling cleaned some Sb₂O₃ particles of one lubricant and coated it with the active lubricant for the specific environment. Mechanisms of lubrication and the role of the different materials will be discussed.     

Tribological characteristics of low-pressure plasma-sprayed A12O3 coating from room temperature to 800 °C

The tribological characteristics of low-pressure plasma-sprayed (LPPS) Al₂O₃ coating sliding against alumina ball have been investigated from room temperature to 800 °C. These friction and wear data have been compared quantitatively with those of bulk sintered alumina to obtain a better understanding of wear mechanisms at elevated temperatures. The friction and wear of Al₂O₃ coating show a strong dependence on temperature, changing from a mild to a severe wear regime with the increase of temperature. The coefficient of friction at room temperature is approximately 0.17 to 0.42, depending on applied load. The tribochemical reaction between the coating surface and water vapor in the environment and the presence of the hydroxide film on the Al₂O₃ coating reduce the friction and wear at room temperature as contrasted to those of bulk sintered alumina. At intermediate temperatures, from 400 to 600 °C, the friction and wear behavior of Al₂O₃ coating depends on the inter-granular fracture and pull-out of Al₂O₃ grains. At above 700 °C, formation and deformation of fine grain layer, and abrasive wear in the form of removal of fine alumina grains further facilitate the friction and wear process of Al₂O₃ coating.     

Friction and Wear Properties of IF–MoS2 as Additive in Paraffin Oil

Inorganic fullerene-like (IF) MoS₂ nanoparticles with diameters ranging from 70 to 120 nm were synthesized by desulphurizing the MoS₃ precursor and characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Tribological properties of the IF–MoS₂, as lubricating oil additive, were evaluated using a MMW-1 four-ball tribotester. The wear scar was examined with an optical microscope and scanning electron microscopy (SEM). The wear resistance of the paraffin oil was improved and the friction coefficient of the oil was decreased by addition of the IF–MoS₂ nanoparticles. The mechanism of friction and wear of the IF–MoS₂ nanoparticles was discussed.     

High load AFM friction and wear experiments on V2O5 thin films

High load friction and wear experiments by means of atomic force microscopy were carried out at the surface of highly (0 0 1) oriented vanadium oxide V₂O₅ thin films deposited on silicon by reactive magnetron sputtering. Microscopic friction coefficient was estimated for wide range of loads. The nature of surface wear due to multiple, high load scanning is presented and discussed.     

Improvement of tribological performance of steel by solid lubricant shot-peening in dry rolling/sliding contact wear tests

The effect of shot-peening treatment with the particulate MoS₂ solid lubricant on the wear resistance of steel in the dry rolling/sliding contact wear tests was investigated. The duplex shot-peening treatment with ceramic balls and the particulate MoS₂ solid lubricant provided excellent wear resistance under a severe loading and sliding condition because the uniform and minute surface roughness given by shot-peening treatment with ceramic balls could keep shot-peened MoS₂ particles with a low friction coefficient on the sample surface. Furthermore, the sample surface was covered with shot-peened MoS₂ particles by a MoS₂ layer formed during the rolling/sliding contact wear test.     

The effect of Al2O3 on the friction performance of automotive brake friction materials

This study consists of two stages. In the first stage, bronze-based break linings were produced and friction-wear properties of them were investigated. In the second stage, 0.5%, 1%, 2% and 4% alumina (Al₂O₃) powders were added to the bronze-based powders and Al₂O₃ reinforced bronze-based break linings were produced. Friction–wear properties of the Al₂O₃ reinforced samples were aslo investigated and compared to those of plain bronze-based ones. For this purpose, friction coefficient and wear behaviour of the samples were tested on the grey cast iron disc. The hardness and density of the samples were also determined. Microstructures of the samples before and after the sintering and the worn surfaces of the wear specimens were examined using a scanning electron microscope (SEM). The sample compacted at 350 MPa and sintered at 820 °C exhibited the optimum friction–wear behaviour. With increase in friction surface temperature, a reduction in the friction coefficient of the samples was observed. The lowest reduction in the friction coefficient with increasing temperature was for the 2% and 4% Al₂O₃ reinforced samples. The SEM images of the sample indicated that increase in Al₂O₃ content resulted in adhesive wear. With increase in Al₂O₃ content, a reduction in mass loss of the samples was also observed. Overall, the samples reinforced with 2% and 4% Al₂O₃ exhibited the best results.     

Study on the tribological properties of surfactant-modified MoS2 micrometer spheres as an additive in liquid paraffin

Tribological properties of MoS₂ micrometer spheres modified by self-prepared surfactant as an additive in liquid paraffin (LP) are studied and compared with those of the commercial colloidal MoS₂ on a four-ball tester and an Optimol SRV oscillating friction and wear tester. The worn surfaces are examined with SEM and XPS, respectively. Results show that MoS₂ micrometer sphere is a much better extreme-pressure additive and anti-wear and friction-reducing additive in LP than the commercial colloidal MoS₂. The boundary lubrication mechanism can be deduced as an effective chemical adsorption protective film formed by the long chain alkyl and active elements (S and N) in the prepared surfactant and tribochemical reaction film composed of the tribochemical reaction products of the additive. Moreover, sliding and rolling frictions exist simultaneously in the MoS₂ micrometer spheres /LP lubricating system, which also do more contributions to the good tribological properties.     

Tribological properties of NiCr–Al2O3 cermet-based composites with addition of multiple-lubricants at elevated temperatures

The tribological properties of NiCr-40 wt% Al₂O₃ (NC40A) cermet-based composites containing SrSO₄ and other lubricant (graphite, MoS₂ and Ag) against alumina ball were evaluated to identify their self-lubrication mechanisms from room temperature to 800 °C. The composites demonstrated distinct improvements in effectively reducing friction and wear, as compared to NC40A cermet. The best results were observed for NC40A–10SrSO₄–10Ag composite, which exhibited satisfactory reproducibility of friction coefficient over a wide temperature range (200–800 °C) through high temperature cyclic friction tests due to the formation of synergistic lubricating films SrAl₄O₇, NiCr₂O₄ and Ag on the contact surface.     

MoS2 single sheet lubrication by molybdenum dithiocarbamate

The mechanisms by which Modtc reduces friction in the centirange under boundary lubrication have been investigated using analytical tribometry. First, the SRV friction test was coupled with energy-filtering TEM on wear fragments and spatially-resolved XPS inside the wear scars. Second, we performed UHV friction tests on Modtc tribofilms previously created on a large area. The overall data demonstrate that the mechanisms of friction-reduction by Modtc is attributed to the effect of sliding between single layers of MoS₂ only, and not to intra-sliding in MoS₂ 3-D crystal. Highly-dispersed MoS₂ sheets are present in a carbon matrix in the tribofilm material. The growth of the 2-D MoS₂ single sheets is thought to be formed by degradation of the Modtc molecule by electron transfer mechanisms activated by the friction process. The lubrication of the uncoated, stationary counterface is attributed to successive transfer of individual sheets towards the friction surface. Practically, in these conditions only a few per cent of dispersed MoS₂ is sufficient to lubricate at the same level as pure MoS₂.     

Wear and friction behavior of alloyed gray cast iron with solid lubricants under boundary lubrication

Friction and wear behavior of MoS₂, boric acid, graphite and TiO₂ has been compared under extreme boundary lubrication condition. Boundary lubrication was simulated for the study. Results show that MoS₂ and graphite were 30-50% more effective than other two lubricants. Friction coefficient shows a decreasing trend with increase in sliding speed due to increasing temperature and higher shear force. High friction coefficient values were recorded for all the lubricants (0.2-0.5). This is due to predominating solid interactions during boundary lubrication condition. Boric acid and TiO₂ were not much effective in lubrication.     

Wear and frictional behaviour of MoS2 pellets and steel lubricated with MoS2 powder

The wear and frictional behaviour of compressed pellets of molybdenum disulphide (MoS₂) were measured when the pellets were slid against a 0.45% C steel disk in air. The wear of the MoS₂ pellets decreased with increasing sliding velocity and increasing contact pressure. These factors are indicated by a parameter μPV which corresponds to the frictional heat. A thin deformed surface layer on the sliding surface of an MoS₂ pellet was different from the MoS₂ substrate.The wear of a bearing steel slider against mild steel was reduced by an MoS₂ film in air and in vacuum. The specific wear rate of the slider and the coefficient of friction were influenced by the degree of vacuum.     

Lubrication at 750°C in a vacuum by a transfer film from self‐lubricating composites for roll/slide contact of Si3N4

Roll/slide friction tests were carried out at a temperature of 750°C in a vacuum. Disc specimens were made of Si₃N₄ with or without a sputtered MoS₂ film. A pin specimen was rubbed against one disc to supply a lubricating transfer film. With a pin made of an MoS₂‐based composite, the friction coefficient was around 0.3 and almost no wear of the discs was observed after 24 h of operation at a load of 50 N, a rotating speed of 0.5 m/s, and a slip ratio of 10%. Transferred patchy MoS₂ films were observed on the friction track. With a pin made of Ni‐based composite containing BN and graphite, the friction coefficient increased from 0.2 to 0.7 over a test time of about 8 h and severe disc wear was found. In an additional test using Si₃N₄ discs with a sputtered MoS₂ film without a pin, the friction coefficient was about 0.3, and no wear of the discs was found after 24 h of operation. The appearance of the friction track was similar to that in the test using the MoS₂‐based composite pin. It seems that the sputtered MoS₂ film wore, but wear particles reattached on the friction path to develop an effective lubricating film. These results demonstrate the effectiveness of transfer film lubrication for long‐term operation in a high‐temperature vacuum, and the superior ability of MoS₂ to develop an effective transfer film.     

Effect of cutting atmosphere on dry machining performance with Al2O3/ZrB2/ZrO2 ceramic tool

In this paper, Al₂O₃/ZrB₂/ZrO₂ ceramic cutting tool was produced by hot pressing. Dry cutting tests in air and nitrogen atmospheres were carried out on normalized AISI 1045 steel. The tool wear, cutting temperature, cutting force, and friction coefficient were measured. Compared in nitrogen, the friction coefficient in air was reduced when the cutting speed was higher than 160 m/min. Scanning electron microscopy and energy dispersive X-ray analysis techniques were employed to observe the worn surfaces of the ceramic tools, and the wear mechanisms were simultaneously discussed. Experimental data and observations revealed the formation of oxide film under air in dry machining, which related to the decrease of the friction coefficient and the improvement of cutting performance.     

Wear properties of two-phase Al2O3/ZrO2 (Y2O3) ceramics at temperatures from 296 to 1073 K

Reciprocating sliding friction experiments were conducted with various two-phase, directionally solidified Al₂O₃/ZrO₂ (Y₂O₃) pins sliding on B₄C flats in air at temperatures of 296, 873, and 1073 K under dry sliding conditions. Results indicate that all the Al₂O₃/ZrO₂ (Y₂O₃) ceramics, from highly Al₂O₃-rich to ZrO₂-rich, exceed the main wear criterion requirement of 10⁻⁶ mm³ N⁻¹ m⁻¹ or lower for effective wear-resistant applications. Particularly, the eutectics and Al₂O₃-rich ceramics showed superior wear properties. The composition and microstructure of Al₂O₃/ZrO₂ (Y₂O₃) ceramics played a dominant role in controlling the wear and friction properties. The controlling mechanism of the ceramic wear, friction, and hardness was an intrinsic effect involving the resistance to shear fracture of heterophase bonding and cohesive bonding and the interlocking microstructures at different scales in the ceramics.     

A study on friction and wear characteristics of nanometer Al2O3 /PEEK composites under the dry sliding condition

The friction and wear properties of the polyetheretherketone (PEEK) based composites filled with 5 mass% nanometer or micron Al₂O₃ with or without 10 mass% polytetrafluroethylene (PTFE) against the medium carbon steel (AISI 1045 steel) ring under the dry sliding condition at Amsler wear tester were examined. A constant sliding velocity of 0.42 m s⁻¹ and a load of 196 N were used in all experiments. The average diameter 250 μm PEEK powders, the 15 or 90 nm Al₂O₃ nano-particles or 500 nm Al₂O₃ particles and/or the PTFE fine powders of diameter 50 μm were mechanically mixed in alcohol, and then the block composite specimens were prepared by the heat compression moulding. The homogeneously dispersion of the Al₂O₃ nano-particles in PEEK matrix of the prepared composites was analyzed by the atomic force microscopy (AFM). The wear testing results showed that nanometer and micron Al₂O₃ reduced the wear coefficient of PEEK composites without PTFE effectively, but not reduced the friction coefficient. The filling of 10 mass% PTFE into pure PEEK resulted in a decrease of the friction coefficient and the wear coefficient of the filled composite simultaneously. However, when 10 mass% PTFE was filled into Al₂O₃/ PEEK composites, the friction coefficient was decreased and the wear coefficient increased. The worn scars on the tested composite specimen surfaces and steel ring surfaces were observed by scanning electron microscopy (SEM). A thin, uniform, and tenacious transferred film on the surface of the steel rings against the PEEK composites filled with 5 mass% 15 nm Al₂O₃ particles but without PTFE was formed. The components of the transferred films were detected by energy dispersive spectrometry (EDS). The results indicated that the nanometer Al₂O₃ as the filler, together with PEEK matrix, transferred to the counterpart ring surface during the sliding friction and wear. Therefore, the ability of Al₂O₃ to improve the wear resistant behaviors is closely related to the ability to improve the characteristics of the transfer film.     

The Effects of Dopants on the Chemistry and Tribology of Sputter-Deposited MoS2 Films

The fact. that dopants improve the friction and wear properties of sputtered MoS₂ films is well known. However, the role of dopants in the mechanisms governing friction and wear are not well understood. The purpose of this work is to gain a fundamental understanding of their role by co-depositing a number of materials, i.e., Ni, Fe, Au, and. Sb₂O₃, with MoS₂ and evaluating their effects on film chemistry, crystallinity, microstructure, and tribology. Friction and wear measurements were collected, using ball-on-flat and dual-rub shoe tribom-eters. Other physical and chemical properties were obtained using SEM, XPS, XRD) and Raman spectroscopy. Crystalline MoS₂ was seen in all of the films. In Sb₂O₃-doped films, an amorphous phase was also observed. The presence of dopants caused film densification and affected crystallite size. They had little effect on the overall crystallite orientation. In addition, dopants caused a reduction in the mean and. variance of the friction coefficient and an increase in wear life. The correlation between dopants, film properties, and tribology is discussed in detail.