High Density Polyethylene/Paraffin Composites as Form-stable Phase Change Material for Thermal Energy Storage

Abstract

This article focuses on the preparation and thermo-physical properties of paraffin/high density polyethylene (HDPE) composites as form-stable solid-liquid phase change material (PCM) for thermal energy storage. In the paraffin/HDPE blend, the paraffin (P) dispersed into the HDPE serves as a latent heat storage material when the HDPE, as a supporting material, prevents the melted paraffin leakage thanks to its structural strength. Therefore, this type composite is form-stable and can be used as a PCM without encapsulation for thermal energy storage. In this study, two paraffins with melting temperatures of 48°C–50°C and 63°C–65°C were used. The mass percentages of paraffins in the composites could go high as 76% without any seepage of the paraffin in melted state. The dispersion of the paraffin into the network of the solid HDPE was investigated using scanning electronic microscope (SEM). The melting temperatures and latent heats of the form-stable P1/HDPE and P2/HDPE composite PCMs were determined as 44.32°C and 61.66°C, and 179.63 and 198.14 Jg^?1, by the technique of differential scanning calorimetry (DSC), respectively. Furthermore, the thermal conductivity of the composite PCMs were improved as about 33.3% for the P1/HDPE and 52.3% for the P2/HDPE by introducing the expanded and exfoliated graphite to the samples in the ratio of 3 wt%. The results reveal that the prepared form-stable composite PCMs have great potential for thermal energy storage applications in terms of their satisfactory thermal properties, improved thermal conductivity and cost-efficiency because of no encapsulation for enhancing heat transfer in paraffin.     

Micro-encapsulated paraffin/high-density polyethylene/wood flour composite as form-stable phase change material for thermal energy storage

Six novel polymer-based form-stable composite phase change materials (PCMs), which comprise micro-encapsulated paraffin (MEP) as latent heat storage medium and high-density polyethylene (HDPE)/wood flour compound as supporting material, were prepared by blending and compression molding method for potential latent heat thermal energy storage (LHTES) applications. Micro-mist graphite (MMG) was added to improve thermal conductivities. The scanning electron microscope (SEM) images revealed that the form-stable PCMs have homogeneous constitution and most of MEP particles in them were undamaged. Both the shell of MEP and the matrix prevent molten paraffin from leakage. Therefore, the composite PCMs are described as form-stable PCMs. The differential scanning calorimeter (DSC) results showed that the melting and freezing temperatures as well as latent heats of the prepared form-stable PCMs are suitable for potential LHTES applications. Thermal cycling test indicated the form-stable PCMs have good thermal stability although it was subjected to 100 melt–freeze cycles. The thermal conductivity of the form-stable PCM was increased by 17.7% by adding 8.8 wt% MMG. The results of mechanical property test indicated that the addition of MMG has no negative influence on the mechanical properties of form-stable composite PCMs. Taking one with another, these novel form-stable PCMs have the potential for LHTES applications in terms of their proper phase change temperatures, improved thermal conductivities, outstanding leak tightness of molten paraffin and good mechanical properties.     

The micro‐/nano‐PCMs for thermal energy storage systems: A state of art review

With advancement in technology—nanotechnology, various thermal energy storage (TES) materials have been invented and modified with promising thermal transport properties. Solid‐liquid phase change materials (PCMs) have been extensively used as TES materials for various energy applications due to their highly favourable thermal properties. The class of PCMs, organic phase change materials (OPCMs), has more potential and advantages over inorganic phase change materials (IPCMs), having high phase change enthalpy. However, OPCMs possess low thermal conductivity as well as density and suffer leakage during the melting phase. The encapsulation technologies (ie, micro and nano) of PCMs, with organic and inorganic materials, have a tendency to enhance the thermal conductivity, effective heat transfer, and leakage issues as TES materials. The encapsulation of PCMs involves several technologies to develop at both micro and nano levels, called micro‐encapsulated PCMs (micro‐PCM) and nano‐encapsulated PCMs (nano‐PCM), respectively. This study covers a wide range of preparation methods, thermal and morphological characteristics, stability, applications, and future perspective of micro‐/nano‐PCMs as TES materials. The potential applications, such as solar‐to‐thermal and electrical‐to‐thermal conversions, thermal management, building, textile, foam, medical industry of micro‐ and nano‐PCMs, are reviewed critically. Finally, this review paper highlights the emerging future research paths of micro‐/nano‐PCMs for thermal energy storage.     

金属基相变材料的研究进展及应用

金属基相变材料由于具有储能密度高、热稳定性好、热导率高等优点,在潜热热能储存系统中具有极大的优势。本文回顾了金属基相变材料的发展历程,归纳了金属基相变材料的性能参数,总结了各种热物性的测量方法,探讨了金属基相变材料与容器材料的相容性问题,分析了金属基相变材料在太阳能热发电、工业余热回收和电力削峰填谷中的应用前景。金属基相变材料的高温腐蚀性是目前限制其在热控制中应用的主要因素。为了实现金属基相变材料的广泛应用,需要重点解决金属基相变材料的封装问题。     

Review on the low melting point alloys for thermal energy storage and heat transfer applications

低熔点合金具有导热系数高,储能密度大,使用温度范围广,性能稳定等特点,是一种潜在的宽温域传热工质和中低温相变储热材料.结合低熔点合金的相变温度,相变潜热,热导率及相变稳定性等热物理性能,综述了低熔点合金相变储热材料的研究进展;介绍了液态低熔点合金传热材料的蒸汽压,表面张力,黏度及比热容等性能,以及低熔点合金在高温下与容器材料的相容性;对低熔点合金传热储热材料的下一步研究进行了展望.     

Synthesis and Characterization of Disodium Hydrogen Phosphate Dodecahydrate-Lauric-Palmitic Acid Used for Indoor Energy Storage Floor Units

Organic and inorganic phase change materials(PCMs) are considered potential materials for thermal energy storage(TES) with different phase change characteristics. In this study, a novel organic-inorganic composite phase change material(PCM) called disodium hydrogen phosphate dodecahydrate-lauric-palmitic acid(D-LA-PACM) was prepared. Expanded graphite(EG) was selected as the support material, and the novel organic-inorganic form-stable PCM called D-LA-PAPCM/EG was prepared using the vacuum adsorption method. Differential scanning calorimetry, Fourier transform infrared spectroscopy, X-ray diffraction, leakage testing, melting and solidification cycle testing, thermal conductivity testing, scanning electron microscopy observation of the micromorphology, and other characterization methods were used to study the microstructure and morphology, thermal physical parameters, thermal conductivity, stability of the PCMs, and the comprehensive material properties of D-LA-PAPCM under the composite action of EG. Results indicated that the melting and freezing temperatures and latent heats of D-LA-PAPCM/EG were measured to be 31.6℃ and 34.3℃ and 142.9 and 142.8 J/g, respectively. Although some of the lauric-palmitic acid(LA-PA) and disodium hydrogen phosphate dodecahydrate(DHPD) separated in the multiple porous structures of EG after 1000 cycles, they could still absorb and release latent heats independently, with D-LA-PAPCM/EG still exhibiting good thermal stability. The thermal conductivity of D-LA-PAPCM/EG was 1.361 W/(m·K). Therefore, the material and thermal properties of the prepared D-LA-PAPCM/EG indicate that it could be well used as a feasible material for energy-saving phase change floor units in indoor TES systems.     

Cellulose-based solid-solid phase change materials synthesized in ionic liquid

A series of cellulose graft poly(ethylene glycol) (cellulose-graft-PEG) copolymers as phase change materials (PCMs) were synthesized in ionic liquid by using 4, 4-diphenylmethane diisocyanate as coupling reagent. FTIR and ¹H NMR characterized the structure of the copolymers. Differential scanning calorimetry (DSC) indicated that the copolymers showed phase transitions with large thermal storage density, and the phase change temperature is in the range of 40-60 °C. The transition temperature and enthalpy can be tailored by changing the molecular weight and the content of poly(ethylene glycol) (PEG) side chains. The copolymers are solid-solid PCMs with good thermal stability. Expanded graphite (EG) with 2, 5 and 10 wt% was added to the PCMs to improve the thermal conductivity. It was found that the thermal conductivity enhanced significantly with increasing EG content. The cellulose-graft-PEG/EG composite PCMs have potential applications in thermal energy storage and temperature control.     

Preparation and characterization of nano‐enhanced myristic acid using metal oxide nanoparticles for thermal energy storage

Fatty acids have been broadly used as phase change materials (PCMs) for thermal energy storage. However, low thermal conductivity limits their performances. This paper investigates the influence of metal oxide nanoparticle addition on myristic acid (MA) as nano‐enhanced PCM (NEPCM). Stability, chemical, and thermal properties were considered. Four types of nanoaprticles, TiO₂, CuO, Al₂O₃, and ZnO, were dispersed in MA at 0.1, 0.5, 1, and 2 wt%. Stability and dispersion were checked by sediment photograph capturing and scanning electron microscopy/energy‐dispersive spectroscopy. The Fourier‐transformed infrared (FTIR) and X‐ray diffraction analysis confirmed no chemical interaction between the nanoparticles and MA. The results revealed a ratio of thermal conductivity of 1.50, 1.49, 1.45, and 1.37, respectively, for 2 wt% of ZnO, Al₂O₃, CuO, and TiO₂. The T‐history method confirmed this enhancement. The latent heat thermal energy storage (LHTES) properties of the nano‐enhanced MA were evaluated using differential scanning calorimetry. The latent heat capacities of nano‐enhanced MA samples have dropped between 9.64 and 5.01 % compared with pure MA, and phase change temperature range was not affected significantly. The NEPCM was subjected to 500 thermal cycling, it showed a good thermal reliability as LHTES properties remained unchanged, while FTIR analysis showed similar characteristics compared with uncycled samples, indicating a good chemical stability. Based on the results regarding with the LHTES properties, cycling thermal reliability, and higher thermal conductivity improvement, it can be achieved that the MA/Al₂O₃ (2.0 wt%) and MA/ZnO (2.0 wt%) composites could be better PCMs for solar TES applications.     

Development of pentadecane/diatomite and pentadecane/sepiolite nanocomposites fabricated by different compounding methods for thermal energy storage

Global warming is one of the most important consequences of excess energy consumption. Phase change materials (PCMs) have prominent advantages in thermal energy storage owing to their high latent heat capacities and small temperature variations during the phase change process. However, leakage is a major problem that limits the use of PCMs. Leakage may occur in encapsulated PCMs or in composites where the PCM is attached to the surface of a supporting material or within the pores of that material. In this study, pentadecane/diatomite and pentadecane/sepiolite nanocomposites were fabricated by using unmodified and microwave‐irradiated diatomite and sepiolite samples and by using different compounding processes, such as direct impregnation, vacuum impregnation, and ultrasonic‐assisted impregnation methods. The microstructures and the chemical and thermal properties of the composites were characterized by scanning electron microscopy, Fourier‐transform infrared spectroscopy, and differential scanning calorimetry. Subsequently, the thermal reliability and stability and the thermal conductivity of the PCM composites were also investigated. A melting temperature of 9.25°C and a latent heat capacity of 58.73 J/g were determined for the pentadecane/diatomite composite that was prepared with the direct impregnation method using a microwave‐treated diatomite sample. The pentadecane/sepiolite composite prepared in the melting temperature range 7.98°C to 8.53°C and latent heat capacity range 41.05 to 46.02 J/g. The results of the thermal analysis indicate that fabricated diatomite‐based or sepiolite‐based PCM composites have good potential as thermal energy storage materials.     

Synthesis and thermal energy storage characteristics of polystyrene-graft-palmitic acid copolymers as solid-solid phase change materials

A series of polystyrene graft palmitic acid (PA) copolymers as novel polymeric solid-solid phase change materials (PCMs) were synthesized. In solid-solid PCMs, polystyrene is the skeleton and PA is a functional side chain that stores and releases heat during its phase transition process. The heat storage of copolymers is due to phase transition between crystalline and amorphous states of the soft segment PA in copolymer and the hard segment polystyrene restricted the free movement of molecular chains of the soft segments even above the phase transition temperature. The copolymers always remain in the solid state during the phase transition processing and therefore they are described as form-stable PCM. Fourier transform infrared spectroscopy (FT-IR) and polarization optical microscopy (POM) analyses were performed to investigate the chemical structures and crystalline morphology. Thermal energy storage properties, thermal reliability and thermal stability of the PCMs were investigated by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) methods. Thermal conductivities of the PCMs were also measured using thermal property analyzer. The analysis results indicated that the PA chains were successfully grafted onto the polystyrene backbone and the copolymers showed typical solid-solid phase transition properties. Moreover, thermal cycling test showed that the copolymers have good thermal reliability and chemical stability although they were subjected to 5000 heating/cooling cycling. The synthesized polystyrene-graft-PA copolymers as novel solid-solid PCMs have considerable potential for such as underfloor heating, thermo-regulated fibers and heating and cooling of agricultural greenhouses. Especially, the polystyrene-graft-PA copolymer including 75% PA is the most attractive PCM due to its highest latent heat storage capacity in the synthesized copolymer PCMs.     

High latent heat storage and high thermal conductive phase change materials using exfoliated graphite nanoplatelets

Using exfoliated graphite nanoplatelets (xGnP), paraffin/xGnP composite phase change materials (PCMs) were prepared by the stirring of xGnP in liquid paraffin for high electric conductivity, thermal conductivity and latent heat storage. xGnP of 1, 2, 3, 5 and 7 wt% was added to pure paraffin at 75 °C. Scanning electron microscopy (SEM) morphology showed uniform dispersion of xGnP in the paraffin wax. Good dispersion of xGnP in paraffin/xGnP composite PCMs led to high electric conductivity. The percolation threshold of paraffin/xGnP composite PCMs was between 1 and 2 wt% in resistivity measurement. The thermal conductivity of paraffin/xGnP composite PCMs was increased as xGnP loading contents. Also, reproducibility of paraffin/xGnP composite PCMs as continuous PCMs was manifested in results of electric and thermal conductivity. Paraffin/xGnP composite PCMs showed two peaks in the heating curve by differential scanning calorimeter (DSC) measurement. The first phase change peak at around 35 °C is lower and corresponds to the solid-solid phase transition of the paraffin, and the second peak is high at around 55 °C, corresponding to the solid-liquid phase change. The latent heat of paraffin/xGnP composite PCMs did not decrease as loading xGnP contents to paraffin. xGnP can be considered as an effective heat-diffusion promoter to improve thermal conductivity of PCMs without reducing its latent heat storage capacity in paraffin wax.     

Improving indoor thermal comfort by using phase change materials: A review

Phase change materials (PCMs) have great potentials to be used in modern building materials to stabilize indoor temperature fluctuations for improving thermal comfort. This paper presents a comprehensive review on the use of PCMs in buildings to improve thermal comfort without increasing energy consumption. Concise discussions of the experimental and computational works reported in literature are presented. A special focus of this review is devoted to discussing different analysis methods and models used to test, characterize, and measure the performance of PCMs in modern building applications under different conditions. This detailed review also highlights the special attention given to organic PCMs, such as paraffin, due to their favorable properties, such as low price, chemical stability, non‐corrosiveness, and high latent heat of fusion. The review shows the scarcity of literature reporting the use of eutectic PCMs in building applications, despite their high volumetric storage density.     

High-chain fatty acid esters of myristyl alcohol with even carbon number: Novel organic phase change materials for thermal energy storage—1

High-chain fatty acid esters have not been investigated for their thermal properties as phase change materials (PCMs) in thermal energy storage. A series of high-chain fatty acid esters of myristyl alcohol (1-tetradecanol) were synthesized via esterification of lauric, myristic, palmitic, stearic and arachidic acids under vacuum and in the absence of any catalyst. The esterification reactions were studied by FT-IR spectroscopy. A differential scanning calorimeter (DSC) and a thermo-gravimetric analyzer (TGA) were intensively used to determine the thermal properties of the introduced thermal storage materials. The thermal properties were given in terms of phase change temperature, enthalpy, specific heat (C_p) and thermal decomposition temperature with related statistical data. The thermal reliability of the novel organic PCMs was investigated by thermal cycling with 1000 thermal cycles with respect to the thermal properties of the original synthesized PCMs. In addition to the synthesized esters, one commercial product was also investigated. The DSC analyses indicated that the melting points of the novel organic PCMs were between 38 and 53 °C with phase change enthalpy above 200 kJ/kg. The effect of chemical structure of the materials on thermal properties was also discussed. The results showed that these materials were favorable for low temperature heat transfer applications with superior thermal properties and reliability.     

Synthesis and thermal properties of poly(styrene-co-ally alcohol)-graft-stearic acid copolymers as novel solid–solid PCMs for thermal energy storage

A series of poly(styrene-co-allyalcohol)-graft-stearic acid copolymers were synthesized as novel polymeric solid–solid phase change materials (SSPCMs). The graft copolymerization reactions between poly(styrene-co-allyalcohol) and stearoyl chloride were verified by Fourier transform infrared (FT-IR) and Proton Nuclear Magnetic Resonance (¹H NMR) spectroscopy techniques. The crystal morphology of the SSPCMs was investigated using polarized optical microscopy (POM) technique. Thermal energy storage properties of the synthesized SSPCMs were measured using differential scanning calorimetry (DSC) analysis. The POM results showed that the crystalline phase of the copolymers transformed to amorphous phase above their phase transition temperatures. Thermal energy storage properties of the synthesized SSPCMs were investigated by differential scanning calorimetry (DSC) and found that they had typical solid–solid phase transition temperatures in the range of 27–30 °C and high latent heat enthalpy between 34 and 74 J/g. Especially, the copolymer with the mole ratio of 1/1 (poly(styrene-co-allyalcohol)/stearoyl chloride) is the most attractive one due to the highest latent heat storage capacity among them. The results of DSC and FT-IR analysis indicated that the synthesized SSPCMs had good thermal reliability and chemical stability after 5000 thermal cycles. Thermogravimetric (TG) analysis results suggested that the synthesized SSPCMs had high thermal resistance. In addition, thermal conductivity measurements signified that the synthesized PCMs had higher thermal conductivity compared to that of poly(styrene-co-allyalcohol). The synthesized copolymers as novel SSPCMs have considerable potential for thermal energy storage applications such as solar space heating and cooling in buildings and greenhouses.     

Galactitol hexa stearate and galactitol hexa palmitate as novel solid-liquid phase change materials for thermal energy storage

Galactitol has a melting point of 187.41 °C and a fusion enthalpy of 401.76 J g⁻¹. Its melting temperature is not suitable for many thermal energy storage applications although it has good latent heat storage capacity compared to the several traditional phase change materials (PCMs). The galactitol also has high supercooling degree as about 72 °C. These unfavorable properties limit the usage potential of galactitol in thermal energy storage applications. However, the phase change temperature and supercooling degree of galactitol can be reduced to a reasonable value and therefore its feasibility for energy storage systems can be increased. For this aim, in this study, galactitol hexa stearate (GHS) and galactitol hexa palmitate (GHP) were prepared as novel solid-liquid PCM by means of esterification reaction of the galactitol with palmitic acid and stearic acid. The GHP and GHS esters were characterized chemically using FT-IR and ¹H NMR techniques. By using DSC analysis method, the melting temperature and latent heat value of the PCMs were determined as 31.78 °C and 201.66 J g⁻¹ for GHP ester and 47.79 °C and 251.05 J g⁻¹ for GHS ester. Thermal cycling test showed that the prepared PCMs had good thermal reliability after thermal 1000 melting-freezing cycles. Thermogravimetric analysis (TGA) results revealed that the PCMs have good thermal stability over their working temperatures. In addition, thermal conductivity of the prepared PCMs was increased as about 26.3% for GHP and 53.3% for GHS by addition of 5 wt.% expanded graphite. Based on all results it can be concluded that the prepared GHP and GHS esters can be considered as promising solid-liquid PCMs for many energy storage applications such as solar energy storage, indoor temperature controlling in buildings, production of smart textile and insulation clothing due to their good energy storage properties.     

有机相变储能材料的研究进展

有机相变储能材料（PCMs）具有储能密度高、腐蚀性小、性能稳定、毒性小、不易出现相分离和过冷现象等优点,成为目前蓄能技术领域主流应用材料之一。本文主要综述了各类有机PCMs的材料特性,针对其导热系数普遍较低的共性问题,介绍了通过添加高热导率材料和封装PCMs两种强化传热途径的最新研究成果,并浅谈了有机PCMs在建筑节能、太阳能利用及冷却电子设备等中低温储能技术中的实际应用情况。最后,总结了有机PCMs目前存在的一些瓶颈问题及未来研究的重点方向。     

Thermal conductivity and latent heat thermal energy storage characteristics of paraffin/expanded graphite composite as phase change material

This study aimed determination of proper amount of paraffin (n-docosane) absorbed into expanded graphite (EG) to obtain form-stable composite as phase change material (PCM), examination of the influence of EG addition on the thermal conductivity using transient hot-wire method and investigation of latent heat thermal energy storage (LHTES) characteristics of paraffin such as melting time, melting temperature and latent heat capacity using differential scanning calorimetry (DSC) technique. The paraffin/EG composites with the mass fraction of 2%, 4%, 7%, and 10% EG were prepared by absorbing liquid paraffin into the EG. The composite PCM with mass fraction of 10% EG was considered as form-stable allowing no leakage of melted paraffin during the solid–liquid phase change due to capillary and surface tension forces of EG. Thermal conductivity of the pure paraffin and the composite PCMs including 2, 4, 7 and 10 wt% EG were measured as 0.22, 0.40, 0.52, 0.68 and 0.82 W/m K, respectively. Melting time test showed that the increasing thermal conductivity of paraffin noticeably decreased its melting time. Furthermore, DSC analysis indicated that changes in the melting temperatures of the composite PCMs were not considerable, and their latent heat capacities were approximately equivalent to the values calculated based on the mass ratios of the paraffin in the composites. It was concluded that the composite PCM with the mass fraction of 10% EG was the most promising one for LHTES applications due to its form-stable property, direct usability without a need of extra storage container, high thermal conductivity, good melting temperature and satisfying latent heat storage capacity.     

Solar thermal energy discharging from a multiple phase change materials storage tank

In this work we have studied numerically the charging and the discharging of solar thermal energy stored (TES) using latent heat from a storage unit contains PCMs. We have also studied the improvement of the heat transfer between fluid which is the water and the PCMs by adding the fins to our storage unit with various configurations, including in-line fins and staggered fins. Then, we studied the assembly of two PCMs in our storage unit. In addition, an experimental work has been validated. The ANSYSFLUENT 15 code was used to solve the formulation of the fusion/solidification processes, where three users define have been developed to describe the thermo-physical properties of the PCMs.     

Medium‐ and high‐temperature latent heat thermal energy storage: Material database,system review,and corrosivity assessment

Latent heat thermal energy storage refers to the storage and recovery of the latent heat during the melting/solidification process of a phase change material (PCM). Among various PCMs, medium‐ and high‐temperature candidates are attractive due to their high energy storage densities and the potentials in achieving high round trip efficiency. Although a few review studies on high‐temperature PCMs have emerged in the past few years, the quantity, completeness, and accuracy of the presented data are relatively poor. Also, an efficient indexing methodology for retrieving useful PCM data is missing in the open literature. In this article, we created an up‐to‐date PCM database following a holistic review of the PCMs in medium‐ and high‐temperature applications over a temperature range of 100°C to 1680°C. Such effort then allows us to develop an accurate indexing tool for the fast selection of suitable PCM candidates and extraction of the related property data. More specifically, the created PCM database covers 496 entries of PCM materials, which are extracted from the scattered research works published during the year 1956 to 2017. The collected information includes both the basic thermo‐physical properties of PCMs (eg, melting temperature, heat of fusion, and thermal conductivity) and crucial design factors during construction and engineering phases (eg, energy storage density, volume expansion, liquid/solid densities, and cost). The reviewed PCMs comprise a wide variety of materials, including fluorides, chlorides, hydrates, nitrates, carbonates, metals and alloys, and other uncommon compounds and salts. In addition, the current work presents a brief review on high‐temperature latent heat thermal energy storage systems categorized into metallic and non‐metallic systems. The corrosivity and stability of PCMs, which are commonly ignored in previous studies, are also examined.     

Fatty acid/poly(methyl methacrylate) (PMMA) blends as form-stable phase change materials for latent heat thermal energy storage

Fatty acids such as stearic acid (SA), palmitic acid (PA), myristic acid (MA), and lauric acid (LA) are promising phase change materials (PCMs) for latent heat thermal energy storage (LHTES) applications, but high cost is the most drawback which limits the utility area of them in thermal energy storage. The use of fatty acids as form-stable PCM will increase their feasibilities in practical LHTES applications due to reduced cost of the energy storage system. In this regard, a series of fatty acid/poly(methyl methacrylate) (PMMA) blends, SA/PMMA, PA/PMMA, MA/PMMA, and LA/PMMA were prepared as new kinds of form-stable PCMs by encapsulation of fatty acids into PMMA which acts as supporting material. The blends were prepared at different mass fractions of fatty acids (50, 60, 70, 80, and 90% w/w) to reach maximum encapsulation ratio. All blends were subjected to leakage test by heating the blends over the melting temperature of the PCM. The blends that do not allow leakage of melted PCM were identified as form-stable PCMs. The form-stable fatty acid/PMMA (80/20 wt.%) blends were characterized using optic microscopy (OM), viscosimetry, and Fourier transform infrared (FT-IR) spectroscopy methods, and the results showed that the PMMA was compatible with the fatty acids. In addition, thermal characteristics such as melting and freezing temperatures and latent heats of the form-stable PCMs were measured by using differential scanning calorimetry (DSC) technique and indicated that they had good thermal properties. On the basis of all results, it was concluded that form-stable fatty acid/PMMA blends had important potential for some practical LHTES applications such as under floor space heating of buildings and passive solar space heating of buildings by using wallboard, plasterboard or floor impregnated with a form-stable PCM due to their satisfying thermal properties, easily preparing in desired dimensions, direct usability without needing an add encapsulation and eliminating the thermal resistance caused by shell and thus reducing cost of LHTES system.