Hydrogen storage properties of nanocrystalline Mg2Ni prepared from compressed 2MgH2Ni powder

In the present work, nanocrystalline Mg₂Ni with an average size of 20–50 nm was prepared via ball milling of a 2MgH₂Ni powder followed by compression under a pressure of 280 MPa. The phase component, microstructure, and hydrogen sorption properties were characterized by using X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), pressure-composition-temperature (PCT) and synchronous thermal analyses (DSC/TG). Compared to the non-compressed 2MgH₂Ni powder, the compressed 2MgH₂Ni pellet shows lower dehydrogenation temperature (290 °C) and a single-phase Mg₂Ni is obtained after hydrogen desorption. PCT measurements show that the nanocrystalline Mg₂Ni obtained from dehydrogenated 2MgH₂Ni pellet has a single step hydrogen absorption and desorption with fairly low absorption (?57.47 kJ/mol H₂) and desorption (61.26 kJ/mol H₂) enthalpies. It has very fast hydrogen absorption kinetics at 375 °C with about 3.44 wt% hydrogen absorbed in less than 5 min. The results gathered in this study show that ball milling followed by compression is an efficient method to produce Mg-based ternary hydrides.     

In situ preparation of N doped orthorhombic Nb2O5 nanoplates /rGO composites for photocatalytic hydrogen generation under sunlight

The synthesis of nitrogen doped orthorhombic niobium oxide nanoplates/reduced graphene oxide composites (NNb₂O₅/rGO) and their photocatalytic activity towards hydrogen generation from water and H₂S under natural sunlight has been demonstrated, uniquely. Nanostructured NNb₂O₅/rGO is synthesized by in situ wet chemical method using urea as a source of nitrogen and optimized by varying percentage of graphene oxide (GO). X?ray diffraction (XRD) study reveals that NNb₂O₅ have orthorhombic crystal structure with crystalline size, 35 nm. Further, X?ray photoelectron spectroscopy (XPS) confirm the presence of nitrogen and rGO in NNb₂O₅/rGO nanocomposite. Morphological features of (NNb₂O₅/rGO) were examined by FE?SEM and FE?TEM showed Nb₂O₅ nanoplates of diameter 25–40 nm anchored on 2D rGO. Diffuse reflectance spectra depicts the extended absorbance in the visible region with band gap of 2.2 eV. Considering the band gap in the visible region, the photocatalytic hydrogen generation from water and H₂S has been performed. The 1 wt % rGO hybridized NNb₂O₅ (S2) exhibited superior photocatalytic hydrogen generation (537 μmol/h) from water and (1385 μmol/h) from H₂S under sunlight. The improved photocatalytic activity is attributed due to an extended absorbance in the visible region, modified electronic structure upon doping and formation of well defined NNb₂O₅/rGO interface, provides large surface area, accelerates the supression of electron and hole pairs recombination rate. In our opinion, this works may provides facile route for energy efficient and economic approach for fabrication of NNb₂O₅/rGO nanocomposites as a visible light active photocatalyst.     

Study on steam reforming of coal tar over NiCo/ceramic foam catalyst for hydrogen production: Effect of Ni/Co ratio

The effect of Ni/Co ratio on the catalytic performance of NiCo/ceramic foam catalyst for hydrogen production by steam reforming of real coal tar was studied. The NiCo/ceramic foam catalyst was synthesized by deposition-precipitation (DP) method and characterized with different methods. The experiments were conducted in a two-stage fixed-bed reactor. The results showed that the reducibility of the metallic oxides in bimetallic NiCo/ceramic foam catalysts was influenced obviously by the Ni/Co ratio.Both gas and hydrogen yield increased first and then decreased with the decline of Ni/Co ratio, and the highest hydrogen yield of 31.46 mmol g^?1 was obtained when the Ni/Co ratio was 5/5. The lowest coke deposition of 0.34 wt% was generated at the same Ni/Co ratio. The lifetime test showed the catalyst maintained catalytic activity after 14 cycles (28 h), indicating the coal tar steam reforming on NiCo/ceramic foam catalyst is a promising method for hydrogen production.     

Fabrication of Pt-doped carbon aerogels for hydrogen storage by radiation method

A radiation method was investigated to fabricate Pt-doped carbon aerogels (CAsPt). The physicochemical properties of the pristine CAs and CAsPt were systematically characterized by X-ray diffraction, scanning electron microscope, transmission electron microscopy, and nitrogen adsorption measurements. The results showed that not only a great number of Pt nanospheres but also many Pt nanoparticles presented in the network of CAs after radiation. The influence of Pt doping on the hydrogen uptake capacity of CAs was studied. In comparison with the pristine CAs, it was remarkable that the hydrogen uptake capacity of the CAsPt had been significantly enhanced, which was contributed by the hydrogen spillover of Pt.     

Numerical analysis of H2 formation during partial oxidation of H2SH2O upon activation of oxidizer by an electric discharge

The numerical analysis of H₂ production during partial oxidation of H₂SH₂O in a plug-flow reactor at atmospheric pressure and a rather low temperature (T₀ = 500 K) was conducted, when the oxidizer (oxygen or air) was preliminarily activated by an electrical discharge with different values of reduced electric field and input energy. It was shown that a significant hydrogen yield in flow reactor can be obtained only after ignition of the mixture. The ignition delay length depends on the reduced electric field E/N and input energy E_s in the discharge and is minimal at E/N～8–10 Td for the discharge in oxygen and at E/N～4–10 and 120–150 Td in air discharge, when O₂(a¹Δ_g) mole fraction in the discharge products is maximal. If the H₂SH₂OO₂(air) mixture ignites inside the flow reactor, the mole fraction of hydrogen and its relative yield do not depend on E/N. The relative hydrogen yield increases monotonically with an addition of water to H₂S. It was found, that the approach based on the partial oxidation of the H₂SH₂O mixture upon activation of oxygen by an electric discharge can ensure very low energy cost for H₂ production. The minimum specific energy requirement, obtained for the H₂SO₂ mixture, was found to be 0.83 eV/(molecule H₂) and 0.18 eV/(molecule H₂S) at atmospheric pressure and can be further decreased if the energy released during partial oxidation of H₂S is spent on heating the reagents. The use of air as an oxidizer requires higher energy costs and seems to be less promising.     

Hydrogen evolution in the dehydrogenation of methylcyclohexane over Pt/CeMgAlO catalysts derived from their layered double hydroxides

Pt/CeMgAl layered double hydroxides with different Ce contents were prepared by one-step co-precipitation method, which underwent calcination and reduction with hydrogen and were finally converted into Pt/CeMgAlO catalysts. These catalysts were tested in the dehydrogenation of methylcyclohexane (MCH) into toluene to produce hydrogen. The addition of CeO₂ promoted the dispersion of Pt and decreased the Pt particle size. During the dehydrogenation reaction, toluene was the only liquid product and its selectivity was higher than 99.9%. MCH conversion increased with the reaction temperature rising. The conversion and hydrogen evolution rate on Pt/Ce₁₄MgAlO350 reached up to 98.5% and 1358.6 mmol/g_Pt/min at 350 °C. Moreover, Pt/CeMgAlO catalysts exhibited no acidity and presented a high anti-coking ability and good stability. These results suggest that Pt/CeMgAlO catalysts have potential industrial application for hydrogen energy utilization.     

Catalytic transformation of H2S for H2 production

Hydrogen sulfide (H₂S) gas is a by-product from natural gas refining, hydrodesulfurization of various fossil fuels, and syngas cleaning from pyrolysis and gasification. Catalytic pyrolysis of H₂S provides an alternative and effective pathway to recover both H₂ and sulfur. Catalysts from hydrotalcite of ZnAl, ZnNiAl, and ZnFeAl were employed for H₂S pyrolysis and compared with TiO₂ and MoS₂ at atmospheric pressure and temperatures in the range of 923–1123 K. Kinetic analysis was carried out in a packed bed reactor which revealed the effect of H₂S partial pressures to be of the order of 0.8–1 with respect to H₂S. The developed novel catalysts showed improved performance with significantly reduced activation energy compared to TiO₂ by 30 kJ/mol as well as higher H₂S conversion during pyrolysis (17% at 1173 K) than with MoS₂ catalyst, even at high H₂S partial pressure which is necessary for viable hydrogen production. The new approach showed an alternate economical and efficient pathway of catalyst design to obtain high activity and stability for simultaneous H₂ energy and pure sulfur recovery from unwanted H₂S resources.     

Aqueous phase reforming of polyols for hydrogen production using supported PtFe bimetallic catalysts

3-D cubic ordered mesoporous carbon (CMK-9) supported PtFe bimetallic catalysts with a range of PtFe compositions were applied to the aqueous phase reforming (APR) of polyols for hydrogen production. The catalytic performance with respect to the polyol and support used was also studied. The catalysts and supports were characterized via X-ray powder diffraction (XRD), transmission electron microscopy (TEM), N₂ sorption, temperature programmed reduction (TPR), and CO chemisorption techniques. The polyols investigated include ethylene glycol (EG), glycerol, xylitol, and sorbitol. It was found that the addition of Fe to the Pt/CMK-9 catalyst significantly improved catalytic performance, with the optimum Pt:Fe ratio for APR activity being 1:3. It was also observed that, in the PtFe (1:3) system, the CMK-9 support demonstrated better catalytic performance than commercially available activated carbon or alumina. In addition, the catalytic activity of the PtFe/CMK-9 catalyst was successfully increased by both the effect of the water-gas shift reaction, promoted by Fe addition to Pt, and by the structural properties and nature of the CMK-9 support. Moreover, the PtFe (1:3)/CMK-9 catalyst showed efficient catalytic activity for different biomass derivatives (EG, glycerol, xylitol, and sorbitol), with the activity decreasing with increase in the number of carbon atoms.     

Effects of silicon concentration in SOFC alloy interconnects on the formation of oxide scales in hydrocarbon fuels

Oxide scale formations on FeCr alloy interconnects were investigated in anode gas (mixtures of CH₄ and H₂O) atmospheres for solid oxide fuel cells. The silicon concentration in FeCr alloy changed the microstructures of oxide scales, elemental distribution and oxide scale growth rates. Oxide scale is composed of the following phases from surface to inner oxides: FeMn spinel, Cr₂O₃, oxide scale/alloy interface and internal oxides of Si and Al. With decreasing the Si concentration from 0.4 to 0.01 mass%, formation of thin Si and Mn layer was observed inside the FeCr alloy. Oxide scale growth rate constants decreased by lowering the Si concentration in FeCr alloy from 4.2 × 10⁻¹⁸ to 2.1 × 10⁻¹⁸ m² s⁻¹ at 1073 K. Diffusivity of Fe and Cr was changed by the concentration of Si in FeCr alloy, which affects the growth rates of oxide scale. The electrical conductivity of oxidized FeCr alloy shows almost same level regardless the Si concentration (in the orders of 10 S cm⁻² at 1073 K).     

One-pot synthesis of ultrasmall PtAg nanoparticles decorated on graphene as a high-performance catalyst toward methanol oxidation

A one-pot synthesis method is utilized for the fabrication of ultrasmall platinum-silver nanoparticles decorated on graphene (PtAg/G) catalyst. This method has several advantages such as inexpensiveness, simplicity, low temperature, surfactant free, reductant free, being environmentally friendly and greenness. In this work, graphene and silver formate were dispersed in ultrapure water in an ultrasonic bath at 25 °C followed by through a galvanic displacement reaction; to prepare PtAg/G, PtCl₂ was added to the suspension under mild stirring condition. The morphology, crystal structure and chemical compositions of the as-fabricated PtAg/G and Pt/C catalysts were characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD) and Energy dispersive X-ray spectroscopy (EDS) techniques. Electrochemical techniques, including cyclic voltammetry (CV) and chronoamperometry (CA) measurements were used to analyze the electrochemical activity of the PtAg/G and Pt/C catalysts. The TEM images illustrate the uniform distribution of ultrasmall PtAg nanoparticles with the average size of 2–3 nm on the graphene nanosheets. The PtAg/G promoted the current density 2.46 times as much as Pt/C with a negative shift in onset oxidation potential and peak potential for oxidation reaction of methanol. Besides, the novel PtAg/G catalyst shows large electrochemically active surface area, lower apparent activation energy, and higher levels of durability in comparison to the Pt/C catalyst for the oxidation of methanol. The PtAg/G catalyst depicts extraordinary catalytic performance and stability to those of the Pt/C catalyst toward methanol oxidation in alkaline media.     

AuCu alloys deposited on titanium dioxide nanosheets for efficient photocatalytic hydrogen evolution

This work first reports AuCu alloys deposited on the surface of TiO₂ nanosheets (TiNs) to form heterojunction. A simple deposition-precipitation method was used to construct a new type of AuCu/TiNs heterostructures through gradually depositing Au and Cu nanoparticles on TiNs. Such structures served the dual advantage of constructing a heterostructure which can improve visible light absorption, and the formation of a Schottky barrier between AuCu alloys (lower Fermi level) and TiNs (higher Fermi level) which can suppress the recombination of photo-generated charge carriers to improve the overall photocatalytic activity. The mass ratio of Au and Cu in the AuCu/TiNs heterostructures and the sequence and method of their deposition are found to be the important factors which affect the photocatalytic performance. When the mass ratio of Au to Cu was determined to be 1: 1, the AuCu/TiNs heterostructure exhibited the best photocatalytic performance for hydrogen production from water splitting (over 9 times than TiNs, 1.47 times than Au/TiNs, and 1.75 times than Cu/TiNs).     

Noble metal-free FeN-CNFs as an efficient electrocatalyst for oxygen reduction reaction

Carbonaceous materials containing non-precious metal atoms and doped with nitrogen have enthralled stunning attention in the field of electrochemical energy conversion systems. Herein, we demonstrated a facile method to fabricate iron and nitrogen doped carbon nanofiber (FeN-CNFs) catalyst material from ferric chloride and interfacial synthesized polyaniline (PANI) nanofibers, by carbonization process in an inert atmosphere at 800 °C. Further, synthesized material was characterized by elemental analysis and X-ray photoelectron spectroscopy (XPS) that confirms the presence of FeN bonds. The structural and morphological features are studied using various microscopy and spectroscopy techniques. The oxygen reduction reaction (ORR) activity of synthesized catalyst materials was examined by rotating disk electrode experiments in 0.1 M KOH. Among all these synthesized materials FeN-CNFs material showed enhanced ORR activity regarding current density and onset potential. Also, FeN-CNFs catalyst exhibited tolerance to methanol and durability in comparison to commercial Pt/C catalyst. The superior performance of FeN-CNFs may be attributed due to the introduction of Fe and formation of FeN bond in catalyst material.     

Efficient visible-light-driven hydrogen evolution over ternary MoS2/PtTiO2 photocatalysts with low overpotential

By surface-decorating PtTiO₂ hybrid catalyst with MoS₂ nanosheets, we prepared a new MoS₂/PtTiO₂ ternary system as high-performance photocatalysts. The ternary MoS₂/PtTiO₂ outperforms both the binary MoS₂TiO₂ and PtTiO₂ systems in photocatalytic hydrogen evolution with an AQY (apparent quantum yield) value of 12.54% at 420 nm, owing to the unique ternary design that creates more efficient electron transport path and electron-hole separation mechanism. Electrochemical characterization showed that the MoS₂/PtTiO₂ ternary electrode afford an efficient pathway of photo-excited electrons from TiO₂ to surface-decorated Pt nanoparticles using MoS₂ and internal Pt nanoparticles as bridges, thus significantly promoting electron transfer, reducing the system overpotential and leading to the activation of more reactive sites. This internal electron transfer pathway (TiO₂ → Pt (internal) → MoS₂ → Pt (surface)) eliminates the need of other metal cocatalysts because the Pt nanoparticles play two roles of storing the conduction band electrons of TiO₂ and acting as co-catalyst for reduction of protons to hydrogen. This unique ternary metal-semiconductor heterojunction for efficient photocatalytic hydrogen evolution provides a meaningful reference for reasonable design of other hybrid photocatalysts.     

Hydrogen-iodide decomposition over PdCeO2 nanocatalyst for hydrogen production in sulfur-iodine thermochemical cycle

A highly active and stable catalyst for hydrogen-iodide decomposition reaction in sulfur-iodine (SI) cycle has been prepared in the form of PdCeO₂ nanocatalyst by sol-gel method with different calcination temperatures (300 °C, 500 °C, and 700 °C). XRD and TEM confirmed a size around 6–8 nm for PdCeO₂ particles calcined at 300 °C. Raman study revealed large number oxygen vacancies in PdCeO₂-300 when compared to PdCeO₂-500 and PdCeO₂-700. With increase in calcination temperature, the average particle size increased whereas the specific surface area and number of oxygen vacancies decreased. Hydrogen-iodide catalytic-decomposition was carried out in the temperature range of 400°C–550 °C in a quartz-tube, vertical, fixed-bed reactor with 55 wt % aqueous hydrogen-iodide feed over PdCeO₂ catalyst using nitrogen as a carrier gas. PdCeO₂-300 showed hydrogen-iodide conversion of 23.3%, which is close to the theoretical equilibrium conversion of 24%, at 550 °C. It also showed a reasonable stability with a time-on-stream of 5 h.     

Mechanistic insights into tandem amine-borane dehydrogenation and alkene hydrogenation catalyzed by [Pd(NHC)(PCy3)]

The mechanism of tandem dimethylamine-borane (NHMe₂BH₃, DMAB) dehydrogenation and alkene hydrogenation catalyzed by [Pd(NHC)(PMe₃)] are investigated by density functional theory (DFT) calculations [NHC = N,N′-bis(2,6-diisopropylphenyl) imidazole-2-ylidene]. Four possible DMAB dehydrogenation mechanisms have been carefully investigated involving concerted BH/NH activation, sequential BH/NH activation, sequential NH/BH activation, and proton transfer mechanism. DFT studies show that the NH proton transfers to ligated carbene carbon and sequential CH/BH activation is the most kinetically favorable pathway with the lowest activation barrier of 23.8 kcal/mol. For hydrogenation, it was found that a trans-dihydride Pd(II) complex, [Pd(H)₂(NHC)(PMe₃)], formed in the dehydrogenation process, serves as an effective catalyst for reduction of trans-stilbene.     

Electrodeposition of NiMoCu coatings from roasted nickel matte in deep eutectic solvent for hydrogen evolution reaction

It is attractive to design and develop a low-cost and environment friendly material preparation route for the catalysts used in alkaline hydrogen evolution reaction. Mineral reconstruction in chlorination roasting and electrodeposition in deep eutectic solvent have been combined in this work. The electrodeposition of NiMoCu coatings from roasted nickel matte precursor in choline chloride (ChCl)-urea deep eutectic solvent (DES) has been investigated. Cyclic voltammetry (CV) implies that the electrodeposition process of NiMoCu coatings in ChCl-urea DES consists of a one-step reaction of Ni(II), a two-step reaction of Cu(II) and Ni/Mo inductive co-deposition. The hydrogen evolution performance parameters of deposited NiMoCu coatings have been systematically studied in alkaline solution by linear sweep voltammetry (LSV), and the electrochemical surface area (ECSA) has been tested by CV. The hydrogen evolution kinetics of deposited NiMoCu coatings has been further investigated by electrochemical impedance spectroscopy (EIS). Owing to its high electrochemical surface area, the NiMoCu coating deposited on Ni foam at −1.2 V can deliver a current density of 10 mA cm⁻² at an overpotential of 93 mV in 1 M KOH. It is suggested that NiMoCu coating can be a promising candidate for water splitting in alkaline solution.     

PtPd nanoparticles supported on sulfonated nitrogen sulfur co-doped graphene for methanol electro-oxidation

In this paper, sulfonated nitrogen sulfur co-doped graphene (S-NS-GR) nanocomposite, i.e., nitrogen sulfur co-doped graphene functionalized with SO₃H group as a novel catalyst support material was prepared. PtPd nanoparticles (PtPd NPs) were deposited on the surface of S-NS-GR by a facile electrochemical approach. The morphology and structure of Pd-PtNPs/S-NS-GR were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDS) and electrochemical impedance spectroscopy (EIS), respectively. In addition, the electrocatalytic performance of catalyst for methanol oxidation reaction (MOR) was systematically studied by cyclic voltammetry and chronoamperometry in alkaline media. Compared with PtPd NPs supported on nitrogen sulfur co-doped graphene (Pt-PdNPs/NS-GR), the excellent performance of Pd-PtNPs/S-NS-GR is mainly ascribed to the embedding of abundant functional groups (SO₃H) into the NS-GR layers, which not only facilitate the homogeneous distribution of metal NPs, but also strengthen the interaction between metals and support material, thus improve the stability of catalyst in MOR.     

Effects of crack position on fatigue life of large seamless storage vessels made of 4130X for hydrogen refueling station

Fatigue property of CrMo steel is significantly degraded by hydrogen embrittlement (HE), which probably influences the fatigue life of hydrogen storage vessels made of CrMo steel. In this study, tests of fatigue crack growth rate (FCGR) for specimens extracted from the cylinder, juncture and shoulder of a seamless storage vessel made of 4130X for hydrogen refueling station were performed in 45 MPa hydrogen gas. Based on the test results, a finite element method (FEM) based on adaptive grid technique was applied to calculate fatigue life of the vessel with an initial crack at different positions. 3D laser scanning technology was used to build the model which can well conform to the actual vessel. Results indicate that the FCGR of 4130X in 45 MPa hydrogen is approximately 10–15 times of the FCGR in air. The FCGR of specimens from the shoulder is approximately 1.2–1.5 times of that from the cylinder and juncture. However, as the influence of stress distribution, the fatigue life of a vessel with a crack in the middle of the cylinder is lower than that of the vessel which exists crack with the same size at the juncture and shoulder.     

Mesocrystalline Ta2O5 nanosheets supported PdPt nanoparticles for efficient photocatalytic hydrogen production

We successfully synthesized mesocrystalline Ta₂O₅ nanosheets supported bimetallic PdPt nanoparticles by the photo-reduction method. The as-prepared mesocrystalline Ta₂O₅ nanosheets in this work showed amazing visible-light absorption, mainly because of the formation of oxygen vacancy defects. And the as-prepared bimetallic PdPt/mesocrystalline Ta₂O₅ nanaosheets also showed highly enhanced UV–Vis light absorption and highly improved photocatalytic activity for hydrogen production in comparison to that of commercial Ta₂O₅, mesocrystalline Ta₂O₅ nanosheets, Pd/mesocrystalline Ta₂O₅ nanosheets and Pt/mesocrystalline Ta₂O₅ nanosheets. The highest photocatalytic hydrogen production rate of PdPt/mesocrystalline Ta₂O₅ nanaosheets was 21529.52 g^?1 h^?1, which was about 21.2 times of commercial Ta₂O₅, and the apparent quantum efficiency of PdPt/mesocrystalline Ta₂O₅ nanaosheets for hydrogen production was about 16.5% at 254 nm. The highly enhanced photocatalytic activity was mainly because of the significant roles of PdPt nanoparticles for accelerating the charge separation and transport upon illumination. The as-prepared PdPt/mesocrystalline Ta₂O₅ nanaosheets in this work could serve as an efficient photocatalyst for green energy production.     

Theoretical evaluation of PdAg membrane reactor performance during biomass steam gasification for hydrogen production using CFD method

In recent years, biomass has been introduced as a promising solution for environmental crisis. Biomass steam gasification is a valuable process for hydrogen production. Main problem of this process is low conversion and low partial pressure of hydrogen in product stream. PdAg membrane reactor (MR) can be used in biomass steam gasification to improve the process efficiency. Hence, Computational fluid dynamic (CFD) method was used in this study for a detail modeling and analyzing the biomass steam gasification in a two-dimensional PdAg MR. After good agreement of CFD model results with literature experimental data, simulation results was indicated that the PdAg MR has better efficiency compared with traditional reactor (TR). Biomass conversion of near 100%, CO selectivity in the range 0–14 and H₂ recovery of 70% in the best condition were achieved. In addition, different flow patterns (cocurrent and counter-current modules) were compared for MR and overall efficiency (biomass conversion) of counter-current model was obtained higher than co-current model. In summary, for all operating conditions and modules, PdAg MR was showed better efficiency compared with TR.