闭式内可逆中冷回热布雷顿循环的功率优化

考虑高低温侧换热器、回热器和中冷器的热阻损失,以功率为优化目标,对恒温热源条件下内可逆闭式布雷顿循环的高低温侧换热器、回热器和中冷器的热导率以及中间压比的分配进行了优化。借助数值计算,分析了一些主要循环特征参数对最大功率及相应热导率和中间压比分配、双重最大功率的影响。     

变温热源条件下内可逆闭式中冷回热布雷顿循环的功率优化

计入工质与高低浊侧换热器、回热器和中冷器的热阻损失以功率为优化目标，借助数值计算，研究了变温热源条件下内可逆闭式中冷回热布雷顿循环输出功率最大时，高低温侧换热器、回热器和中冷器的热导率分配以及中间压比与总压比的关系；分析了工质与热源间的热容率匹配对双重最大功率的影响。     

燃气轮机中冷循环功率和功率密度优化比较

计入高低温侧换热器和中冷器的热阻损失、压气机和涡轮机中的不可逆压缩和膨胀损失及管路中压力损失,用有限时间热力学方法导出了变温热源条件下不可逆闭式燃气轮机中冷循环功率和功率密度（功率与循环中最大比容之比）的解析式;分别以功率和功率密度为目标,优化了中间压比、高低温侧换热器及中冷器热导率分配,并对结果进行了比较.     

中冷回热燃气轮机循环换热器热导率最优分配——生态学性能优化

用有限时间热力学方法优化恒温热源条件下闭式中冷回热燃气轮机循环的生态学性能,计入工质与高低温侧换热器、回热器以及中冷器之间的热阻损失、压气机内不可逆压缩和涡轮内部不可逆膨胀损失,导出了循环生态学函数解析式,通过数值计算优化各换热器热导率分配以及中间压比和总压比,得到了循环最优生态学性能.     

不可逆中冷回热太阳能布雷顿循环系统的优化分析

建立了由太阳能集热器模型和不可逆中冷回热布雷顿循环模型组成的恒温热源条件下太阳能布雷顿循环系统,以系统总效率为目标函数,考虑了高低温侧换热器、回热器和中冷器的热阻损失以及压缩机和涡轮机的不可逆损失,借助数值计算对太阳能集热器的工作温度进行了优化,并分析了主要特征参数对总效率的影响．结果表明：太阳能布雷顿循环系统中存在一个最佳的太阳能集热器工作温度和相应的最大总效率及最大总输出功率;在此基础上,通过优化中间压比可使循环系统的总效率和相应的总输出功率达到双重最大值;系统总效率随着回热器传热有效度和光学效率的增加而提高;系统运行时存在一个最佳的总压比．     

不可逆中冷焦耳_布雷顿功热并供系统火用分析

运用热力学火用分析的方法,分别考虑了高低温侧换热器、热回收装置侧换热器和中冷器的热阻损失,以及压缩机和涡轮机中的内不可逆损失,以无因次总输出火用和火用效率为目标函数,借助数值分析的方法,研究了恒温热源条件下不可逆中冷焦耳—布雷顿功热并供系统的火用性能,分析了主要特征参数对无因次总输出火用及火用效率的影响。分析结果表明,当中间压比不变而总压比变化时,存在一组最佳运行参数,使无因次总输出火用达到最大,还存在最大的总输出火用和火用效率以及相对应的一组最佳运行参数。提高中冷器换热有效度可以增加无因次总输出火用和火用效率。     

恒温热源不可逆闭式中冷回热燃气轮机循环的生态学优化

考虑循环过程的内外不可逆性,以生态学函数为目标,优化了总压比和中间压比分配,分析了高低温侧换热器、中冷器和回热器的性能参数对最大生态学函数及其参数的影响,并与以功率为优化目标时的循环性能进行了比较.结果表明:以生态学函数为优化目标时比以功率为优化目标时具有更高的效率,但功率相差不太多,反映了输出功率和效率间的最佳匹配.     

闭式不可逆等温加热修正双布雷顿循环功率与效率特性分析

应用有限时间热力学理论,建立了闭式变温热源不可逆等温加热修正双布雷顿循环模型,推导出循环的无因次功率和效率的解析式。通过数值计算,分析了压气机压比、高低温侧换热器有效度、回热器有效度和燃烧室外侧流体入口温比等特征参数对循环性能的影响。研究结果表明,分别存在一对最优的顶循环压比和底循环压比使循环输出功率和效率取得最大值。提高高低温侧换热器有效度和燃烧室外侧流体入口温比均有利于提高系统输出功率和效率,同时还发现,回热器有效度对该循环功率有影响这一不同于经典热力学结论的新现象。     

闭式变温热源不可逆IFGT循环的生态学优化

计入工质与高、低温侧换热器和回热器的热阻损失、压气机和透平中不可逆压缩和膨胀及管路系统中的压力损失,用有限时间热力学理论和方法,导出了变温热源条件下闭式不可逆外燃式燃气轮机(IFGT,Indirectly Fired Gas Turbine,又称EFGT,Externally Fired Gas Turbine)无因次生态学函数的解析式,通过详细的数值计算,得到了最大生态学函数条件下高、低温侧换热器和回热器的热导率分配及工质和热源间的热容率匹配的全局最优解。     

不可逆变温热源斯特林热机的?生态学性能研究

基于?的生态学目标函数,使用一种新的指标——?生态指标对不可逆变温热源斯特林热机进行了分析。在热机高低温热源的热容均为有限的前提下,考虑斯特林热机的热阻、回热损失、内不可逆性以及热漏对其影响。研究了回热器的回热效率和高低温热源的热容的比值等参数对斯特林热机的功率、效率和?生态学指标的影响,并将结果与另一种生态目标函数的结果进行了比较,得到最佳功率输出功率和热效率。     

Closed intercooled regenerator Brayton-cycle with constant-temperature heat-reservoirs

The performance of an irreversible closed intercooled regenerator Brayton-cycle coupled to constant-temperature heat reservoirs is analyzed by using the theory of finite-time thermodynamics (FTT). Analytical formulae for dimensionless power and efficiency are derived. Especially, the intercooling pressure-ratio is optimized for the optimal power and the optimal efficiency, respectively. The effects of component (the intercooler, the regenerator, and the hot- and cold-side heat-exchangers) effectivenesses, the compressor and turbine efficiencies, the heat-reservoir temperature-ratio, and the temperature ratio of the cooling fluid in the intercooler and the cold-side heat reservoir on the optimal power and the corresponding efficiency and corresponding intercooling pressure ratio, as well as the optimal efficiency and the corresponding power and corresponding intercooling pressure-ratio are analyzed by detailed numerical examples.     

变温热源内可逆中冷回热布雷顿循环功率密度优化

以功率密度为目标，用有限时间热力学的方法，通过数值计算，对变温热源条件下的内可逆中冷回热布雷顿循环的高、低温侧换热器的热导率分配和中间压比、循环总压比和工质与热源间的热容率匹配进行优化。分别得到了最大功率密度、双重最大功率密度和三重最大功率密度，并分析了热力学参数对高低温侧换热器的热导率最优分配、最佳中间压比、最大功率密度和双重最大功率密度的影响。     

A Parametric Study of an Irreversible Closed Intercooled Regenerative Brayton Cycle

Entropy generation minimization technique is used in the analysis of an irreversible closed intercooled regenerative Brayton cycle coupled to variable-temperature heat reservoirs. Mathematical models are developed for dimensionless power and efficiency for a multi-stage Brayton cycle. The dimensionless power and efficiency equations are used to analyze the effects of total pressure ratio, intercooling pressure ratio, thermal capacity rates of the working fluid and heat reservoirs, and the component (regenerator, intercooler, hot- and cold-side heat exchangers) effectiveness. Using detailed numerical examples, the optimal power and efficiency corresponding to variable component effectiveness, compressor and turbine efficiencies, intercooling pressure ratio, total pressure ratio, pressure recovery coefficients, heat reservoir inlet temperature ratio, and the cooling fluid in the intercooler and the cold-side heat reservoir inlet temperature ratio are analyzed.     

Power optimization of an endoreversible closed intercooled regenerated Brayton cycle

In this paper, power is optimized for an endoreversible closed intercooled regenerated Brayton cycle coupled to constant-temperature heat reservoirs in the viewpoint of finite-time thermodynamics (FTT) or entropy generation minimization (EGM). The effects of some design parameters, including the cycle heat reservoir temperature ratio and total heat exchanger inventory, on the maximum power and the corresponding efficiency are analyzed by numerical examples. The analysis shows that the cycle dimensionless power can be optimized by searching the optimum heat conductance distributions among the hot- and cold-side heat exchangers, the regenerator and the intercooler for fixed total heat exchanger inventory, and by searching the optimum intercooling pressure ratio. When the optimization is performed with respect to the total pressure ratio of the cycle, the maximum dimensionless power can be maximized again.     

Power optimization of an endoreversible closed intercooled regenerated Brayton-cycle coupled to variable-temperature heat-reservoirs

In this paper, in the viewpoint of finite-time thermodynamics and entropy-generation minimization are employed. The analytical formulae relating the power and pressure-ratio are derived assuming heat-resistance losses in the four heat-exchangers (hot- and cold-side heat exchangers, the intercooler and the regenerator), and the effect of the finite thermal-capacity rate of the heat reservoirs. The power optimization is performed by searching the optimum heat-conductance distributions among the four heat-exchangers for a fixed total heat-exchanger inventory, and by searching for the optimum intercooling pressure-ratio. When the optimization is performed with respect to the total pressure-ratio of the cycle, the maximum power is maximized twice and a ‘double-maximum’ power is obtained. When the optimization is performed with respect to the thermal capacitance rate ratio between the working fluid and the heat reservoir, the double-maximum power is maximized again and a thrice-maximum power is obtained. The effects of the heat reservoir’s inlet-temperature ratio and the total heat-exchanger inventory on the optimal performance of the cycle are analyzed by numerical examples.     

恒温热源不可逆闭式中冷回热燃气轮机循环的功率和效率

用有限时间热力学方法首次研究了恒温热源条件下不可逆闭式中冷回热燃气轮机循环的功率、效率以及中间压比特性，导出了无因次功率及效率的解析式。通过数值计算方法，分析了中冷度、回热度对循环最优功率、最优效率及其对应的中间压比分配的影响。     

回热式变温热源空气制冷循环容积制冷率优化

考虑热阻损失、压缩机与膨胀机的内损失及管路系统的压力损失，研究一个比较接近实际装置的回热式交温热源空气制冷循环，得出了循环容积制冷率制冷系数的解析关系式。由数值计算分析了压比、热导率分配以及工质与热源间的热容率匹配等参数对容积制冷率的影响。     

Cycle improvements to steam injected gas turbines

The efficiency and specific power of the steam injected gas turbine is analysed by modelling the thermodynamic cycle. In this model special attention is paid to the blade cooling. The basic cycle as well as cycles with improvements such as intercooling, heat recovery by regenerator and blade cooling using steam are studied. The different cycles are compared with the combined cycle and the intercooled regenerative cycle. The conclusion is that the steam injected cycles have high efficiency and specific power. Adding heat exchangers to the cycle is not beneficial. Using steam as coolant for the blades offers interesting perspectives. Copyright © 2000 John Wiley & Sons, Ltd.