改进型格尼襟翼对垂直轴风力机气动性能的影响

直线翼垂直轴风力机气动效率普遍较低，为此提出一种具有内侧、外侧、双侧格尼襟翼和凹槽格尼襟翼的翼型叶片以提升其气动性能。通过数值模拟研究6种新型叶片对垂直轴风力机风能利用率、力矩系数、流场结构和叶片切向力等气动性能的影响。结果表明：6种格尼襟翼叶片均可在一定尖速比（TSR）范围内提高风能利用率，外侧凹槽格尼襟翼最大风能利用率可提高17.92％；外侧格尼襟翼与双侧凹槽格尼襟翼相比原始叶片可有效降低风力机载荷波动并提高平均力矩系数；双侧dimple-GF可改善动态失速特性，明显抑制旋涡发展；单叶片切向力在上游区明显增大，有效提高了风力机气动性能。     

垂直轴风力机两种翼型气动性能比较研究

叶片是风力机最重要的组成部分,在不同的风能资源情况下,翼型的选择对垂直轴风力机气动特性有着重要的影响。文章分别以NACA0018翼型(对称翼型)和NACA4418翼型(非对称翼型)建立3叶片H型垂直轴风力机二维仿真模型。应用数值模拟的研究方法,从功率系数、单个叶片切向力系数等方面比较两种风力机模型在不同叶尖速比下的气动特性,并采用风洞实验数据验证了流场计算的准确性。CFD计算结果表明:在低叶尖速比下,NACA4418翼型风力机气动特性优于NACA0018翼型风力机,适用于低风速区域;在高叶尖速比下,NACA0018翼型风力机气动特性较好,适用于高风速地区。而且在高叶尖速比时,NACA0018翼型在上风区时,切向力系数平均值要高于NACA4418翼型,在下风区时,NACA418翼型切向力系数平均值高。该研究可为小型垂直轴风力机翼型的选择提供参考。     

基于复合形法的垂直轴风力机翼型优化设计

针对低速航空翼型不完全适合垂直轴风力机的问题,采用复合形法对小型垂直轴风力机常用的NACA0015翼型进行了优化设计。在复合形法优化设计过程中,选取翼型的弯度和厚度作为设计变量,以翼型最大切向力系数Ctmax和失速攻角αs的加权和作为目标函数。将XFOIL程序与Viterna-Corrignan失速后模型相结合,计算出优化前后翼型气动性能参数。结果表明,与NACAOO15翼型相比,新翼型的气动性能有了较大提高,最大升力系数增大了33.5%,失速攻角提高了3°,最大切向力系数增大了43.5%。     

新型变桨立轴风力机涡效应分析

该文旨在通过变桨来改善升力型立轴风力机叶片气动特性,提高风力机最大运行效率。针对设计尖速比下风能利用系数较低的问题,提出减小叶片小攻角范围,增大叶片大攻角工作范围,以重点改善叶片低性能区域的气动特性为出发点,提高风能利用系数新变桨思路。以采用NACA0012翼型、2 m高和2 m旋转直径的两叶片H型风力机为研究对象,从涡理论来分析和比较在最佳尖速比为5的条件下,附着涡、尾随涡、脱体涡和桨距角对攻角、切向力和功率输出的影响规律。研究结果表明:变桨后,叶片的攻角、切向力和输出功率在原最大值两侧均有明显提高,拓宽了叶片高性能的工作区域;涡系中脱体涡对叶片气动特性影响最大,其中在上盘面影响较小,在下盘面影响较大;变桨前后涡系对上盘面的差异较小,对下盘面的影响差异较明显;变桨后,下盘面的叶片的涡尾迹弯曲程度在加大。     

叶片最大厚度前部修型的垂直轴风力机气动性能

风力机叶片是使风能转化为机械能的原动机构,是风力机的重要部件,风力机风能利用系数的高低主要取决于其叶片的气动外形。保持直叶片垂直轴风力机使用的NACA0022翼型的对称性不变,改变其叶片最大厚度前部的形状,以期得到高风能利用系数的垂直轴风力机翼型。利用Fluent软件,采用k-ωSST湍流模型和SIMPLE算法,运用滑移网格技术,对由不同叶片构成的风力机进行数值计算。计算结果表明,当叶片最大厚度前部是长短轴比为3∶2的椭圆形状时,风力机的风能利用系数更高,而且处于高风能利用系数的尖速比范围更宽;在尖速比为1.72时,风能利用系数最高,为24.8%,此时的风能利用系数较基本翼型提高了28%。叶片修型提高风力机性能的物理机制是最大厚度点前移后的叶片在大攻角下的扰流流动分离强度减弱了。     

垂直轴风力机改进翼型气动及功率特性研究

为提高垂直轴风力机的风能利用率,基于CFD数值模拟技术,分析了常用典型垂直轴风力机翼型的气动及功率特性,并以NACA0012翼型为基础对其进行改进。对比改进前后翼型表明,增大翼型厚度可降低升阻比,增大翼型弯度可增强其失速特性;厚尾缘翼型、升阻互补型翼型可分别降低翼型失速性能、增加启动力矩,其中厚尾缘翼型的H型垂直轴风力机的功率系数较大,可提高风能利用率,为翼型优化设计提供了新思路。     

兆瓦级H型垂直轴风力发电机气动设计方案的数值模拟研究

为解决兆瓦级H型垂直轴风力发电机气动设计过程中实验和数值模拟方面耗费巨大的问题,基于升力线模拟方法完成了兆瓦级H型垂直轴风力发电机的气动设计,并利用该方法研究不同垂直轴风力机翼型设计方案对整机气动性能的影响,研究结果表明:基元翼型选用NACA0015和NACA0018对称翼型能够获得更高的风能利用率;整机叶片造型方案中,前掠翼型性能优于直叶片,前掠翼型方案的最大风能利用率随掠角增大而小幅上升,完整旋转周期内的风能利用率则随掠角增加先增大后减小,且在掠角3°时可取到整体最大风能利用率;后掠翼型性能差于直叶片,风能利用系数随掠角增大而减小;前掠与后掠组合翼型方案性能稍好于直叶片,但不如前掠叶片;不同方案之间存在性能差异的原因可能在于不同翼型的叶片分离涡在竖直方向上的旋涡脱落顺序方面存在差异,其中上部较早脱落的前掠方案有助于风能利用系数提升,下部较早脱落的后掠方案则会对风能利用系数产生负面影响。     

不同小翼对H型垂直轴风力机叶片压力分布的影响

以翼型为NACA0012的单叶片H型垂直轴风力机为研究对象,采用数值模拟的研究方法,分析叶片两端未安装小翼和安装3种不同叶尖小翼对H型垂直轴风力机叶片表面压力分布和叶尖涡的影响。结果表明:安装小翼均可提高H型垂直轴风力机的最大转矩系数,其中安装Winglet可提高H型垂直轴风力机起动力矩;增加叶尖小翼均对消除叶尖涡有利;H型垂直轴风力机叶片两端安装Winglet小翼较其他两种小翼效果好。     

高效低载的三维风力机叶片外形优化设计方法

常规风力机叶片的优化设计都是从二维翼型开始的,且翼型总是以升阻比最大为优化目标。然而,二维翼型的升阻比最大和三维叶片的高风能利用率与低气动载荷有本质的不同,采用以往的叶片优化方法常常会在提高风能利用率的同时,使叶片所受的气动载荷也提高。针对这一问题,提出基于多岛遗传算法和动量叶素理论,在给定风况条件下,以加权风能利用率最高与气动载荷最小为目标函数,以叶片各个截面的翼型型线及扭角作为设计变量,对三维叶片开展多目标优化方法设计研究。并对某实际NREL Phase VI叶片进行优化设计,结果表明：在给定风况下相比原叶片,优化叶片在风能利用率提升了3.06%的基础上,叶根弯矩降低了11.68%。在变转速与变风况下,优化叶片的气动效率整体提升,叶根弯矩明显降低。     

格尼襟翼垂直轴风力机风场研究

为研究垂直轴风力机风场中机组气动性能受格尼襟翼的影响,采用TSST湍流模型对直线翼垂直轴风力机进行数值模拟研究。结果表明：风场上游风力机组尖速比越大,机组间流体加速效果越显著,使风力机组气动性能高于单风力机;在中低尖速比时,格尼襟翼可有效提升单个风力机气动效率,在尖速比较高时,提升效果并不明显;在风力机组中安装格尼襟翼且可优化上游风力机组尾迹流场并提高机组间流体的加速效果,使下游风力机获得更高的风能利用率;当格尼襟翼风力机组采用交错排布方式时,下游风力机可利用阻塞效应和格尼襟翼的双重优势,叶片平均切向力较单风力机大幅提升,且风场中3台风力机切向力的平均值高于单台风力机,风场中机组整体性能得到提高。     

Performance assessment of some ice TES systems

In this paper, a performance assessment of four main types of ice storage techniques for space cooling purposes, namely ice slurry systems, ice-on-coil systems (both internal and external melt), and encapsulated ice systems is conducted. A detailed analysis, coupled with a case study based on the literature data, follows. The ice making techniques are compared on the basis of energy and exergy performance criteria including charging, discharging and storage efficiencies, which make up the ice storage and retrieval process. Losses due to heat leakage and irreversibilities from entropy generation are included. A vapor-compression refrigeration cycle with R134a as the working fluid provides the cooling load, while the analysis is performed in both a full storage and partial storage process, with comparisons between these two. In the case of full storage, the energy efficiencies associated with the charging and discharging processes are well over 98% in all cases, while the exergy efficiencies ranged from 46% to 76% for the charging cycle and 18% to 24% for the discharging cycle. For the partial storage systems, all energy and exergy efficiencies were slightly less than that for full storage, due to the increasing effect wall heat leakage has on the decreased storage volume and load. The results show that energy analyses alone do not provide much useful insight into system behavior, since the vast majority of losses in all processes are a result of entropy generation which results from system irreversibilities.     

Effect of co-cultivation of Chlamydomonas reinhardtii with Azotobacter chroococcum on hydrogen production

Chlamydomonas reinhardtii cc124 and Azotobacter chroococcum bacteria were co-cultured with a series of volume ratios and under a variety of light densities to determine the optimal culture conditions and to investigate the mechanism by which co-cultivation improves H₂ yield. The results demonstrated that the optimal culture conditions for the highest H₂ production of the combined system were a 1:40 vol ratio of bacterial cultures to algal cultures under 200 μE m^?2 s^?1. Under these conditions, the maximal H₂ yield was 255 μmol mg^?1 Chl, which was approximately 15.9-fold of the control. The reasons for the improvement in H₂ yield included decreased O₂ content, enhanced algal growth, and increased H₂ase activity and starch content of the combined system.     

Exergetic evaluation of 5 biowastes-to-biofuels routes via gasification

This paper presents the exergy analysis results for the production of several biofuels, i.e., SNG (synthetic natural gas), methanol, Fischer–Tropsch fuels, hydrogen, as well as heat and electricity, from several biowastes generated in the Dutch province of Friesland, selected as one of the typical European regions. Biowastes have been classified in 5 virtual streams according to their ultimate and proximate analysis. All production chains have been modeled in Aspen Plus in order to analyze their technical performance. The common steps for all the production chains are: pre-treatment, gasification, gas cleaning, water–gas-shift reactions, catalytic reactors, final gas separation and upgrading. Optionally a gas turbine and steam turbines are used to produce heat and electricity from unconverted gas and heat removal, respectively. The results show that, in terms of mass conversion, methanol production seems to be the most efficient process for all the biowastes. SNG synthesis is preferred when exergetic efficiency is the objective parameter, but hydrogen process is more efficient when the performance is analyzed by means of the 1st Law of Thermodynamics. The main exergy losses account for the gasification section, except in the electricity and heat production chain, where the combined cycle is less efficient.     

液压系统常见的故障诊断及处理

任何工程机械式液压设备使用时出现故障是不可避免的。但是怎样确定故障的原因及找到好的解决方法，这是使用者最关心的问题。讲述了液压系统常见的故障及其排除方法。     

Natural-gas fueled spark-ignition (SI) and compression-ignition (CI) engine performance and emissions

Natural gas is a fossil fuel that has been used and investigated extensively for use in spark-ignition (SI) and compression-ignition (CI) engines. Compared with conventional gasoline engines, SI engines using natural gas can run at higher compression ratios, thus producing higher thermal efficiencies but also increased nitrogen oxide (NO_x) emissions, while producing lower emissions of carbon dioxide (CO₂), unburned hydrocarbons (HC) and carbon monoxide (CO). These engines also produce relatively less power than gasoline-fueled engines because of the convergence of one or more of three factors: a reduction in volumetric efficiency due to natural-gas injection in the intake manifold; the lower stoichiometric fuel/air ratio of natural gas compared to gasoline; and the lower equivalence ratio at which these engines may be run in order to reduce NO_x emissions. High NO_x emissions, especially at high loads, reduce with exhaust gas recirculation (EGR). However, EGR rates above a maximum value result in misfire and erratic engine operation. Hydrogen gas addition increases this EGR threshold significantly. In addition, hydrogen increases the flame speed of the natural gas-hydrogen mixture. Power levels can be increased with supercharging or turbocharging and intercooling. Natural gas is used to power CI engines via the dual-fuel mode, where a high-cetane fuel is injected along with the natural gas in order to provide a source of ignition for the charge. Thermal efficiency levels compared with normal diesel-fueled CI-engine operation are generally maintained with dual-fuel operation, and smoke levels are reduced significantly. At the same time, lower NO_x and CO₂ emissions, as well as higher HC and CO emissions compared with normal CI-engine operation at low and intermediate loads are recorded. These trends are caused by the low charge temperature and increased ignition delay, resulting in low combustion temperatures. Another factor is insufficient penetration and distribution of the pilot fuel in the charge, resulting in a lack of ignition centers. EGR admission at low and intermediate loads increases combustion temperatures, lowering unburned HC and CO emissions. Larger pilot fuel quantities at these load levels and hydrogen gas addition can also help increase combustion efficiency. Power output is lower at certain conditions than diesel-fueled engines, for reasons similar to those affecting power output of SI engines. In both cases the power output can be maintained with direct injection. Overall, natural gas can be used in both engine types; however further refinement and optimization of engines and fuel-injection systems is needed.     

Economie d'énergie en trigénération

Trigeneration is defined as the production of three useful forms of energy—heat, cold and power—from a primary source of energy such as natural gas or oil. For instance, trigeneration systems typically produce electrical power via a reciprocating engine or gas turbine and recover a large percentage of the heat energy retained in the lubricating oil, exhaust gas and coolant water systems to maximize the utilization of the primary fuel. The heat produced can be totally or partially used to fuel absorption refrigerators. Therefore, trigeneration systems enjoy an inherently high efficiency and have the potential to significantly reduce the energy-related operation costs of facilities. In this paper, we describe a model of characterization of trigeneration systems trough the condition of primary energy saving and the quality index, compared to the separate production of heat, cold and power. The study highlights the importance of the choice of the separate production reference system on the level of primary energy saving and emissions reduction.     

Mineralogical characterization of the intraseam layers of Lofoi lignite deposits in Florina basin (western Makedonia,northwest Greece)

The mineralogical composition of intraseam layers from Lofoi lignite deposits (northwest Greece) is the subject of the present study. The samples were examined by means of X-ray diffraction (XRD), thermo-gravimetric (TG/DTG) and differential thermal analysis (DTA), and Fourier transform infrared (FT-IR) spectrometry. The clay minerals prevail in most samples, with illite-muscovite being the dominant phase, and kaolinite and chlorite being the other major clay components. No smectite was found. Quartz and feldspars, dominate in two cases. The studied materials are characterized as clays to clayey sands, showing significant similarities with the intraseam layers of the adjacent Achlada lignite deposits.     

Ash-forming elements in four Scandinavian wood species. Part 1: Summer harvest

Woody biomass in Finland and Sweden comprises mainly four wood species: spruce, pine, birch and aspen. To study the ash, which may cause problems for the combustion device, one tree of each species were cut down and prepared for comparisons with fuel samples. Well-defined samples of wood, bark and foliage were analyzed on 11 ash-forming elements: Si, Al, Fe, Ca, Mg, Mn, Na, K, P, S and Cl. The ash content in the wood tissues (0.2–0.7%) was low compared to the ash content in the bark tissues (1.9–6.4%) and the foliage (2.4–7.7%). The woods’ content of ash-forming elements was consequently low; the highest contents were of Ca (410–1340 ppm) and K (200–1310), followed by Mg (70–290), Mn (15–240) and P (0–350). Present in the wood was also Si (50–190), S (50–200) and Cl (30–110). The bark tissues showed much higher element contents; Ca (4800–19,100 ppm) and K (1600–6400) were the dominating elements, followed by Mg (210–2400), P (210–1200), Mn (110–1100) and S (310–750), but the Cl contents (40–330) were only moderately higher in the bark than in the wood. The young foliage (shoots and deciduous leaves) had the highest K (7100–25,000 ppm), P (1600–5300) and S (1100–2600) contents of all tissues, while the shoots of spruce had the highest Cl contents (820–1360) and its needles the highest Si content (5000–11,300). This paper presented a new approach in fuel characterization: the method excludes the presence of impurities, and focus on different categories of plant tissues. This made it possible to discuss the contents of ash element in a wide spectrum of fuel-types, which are of large importance for the energy production in Finland and Sweden.     

Innovative methodologies in renewable energy: A review

This paper is concerned with innovative approaches to renewable energy sources computation methodologies, which provide more refined results than the classical alternatives. Such refinements provide additional improvements especially for replacement of fossil energy usages that emit greenhouse gas (GHG) into the atmosphere leading to climate change impact. Current knowledge gap among each renewable energy source calculation is rather missing fundamentals of plausible, rational, and logical explanations for the interpretation of results. In the literature, there are rather complicated and mechanically applicable methodologies, which require input and output measurement data match with missing physical explanations. The view taken in this review paper is to concentrate on quite plausible, logical, rational, and effectively applicable innovative energy calculation methodologies with simplistic fundamentals. For this purpose, a set of renewable energy methodological approaches is revisited with their innovative structures concerning solar, wind, hydro, current, and geothermal energy resources. With the increase in the renewable energy utilizations to combat the undesirable impacts of global warming and climate change, there is a need for better models that will include physical environmental conditions and data properties in the probabilistic, statistical, stochastic, logical, and rational senses leading to refined and more reliable estimations with application examples in the text. Finally, new research directions are also recommended for more refined innovative energy system calculations.     

Decomposition of limestone in a solar reactor

The thermal decomposition of limestone has been selected as a model reaction for developing and testing an atmospheric open solar reactor. The reactor consists of a cyclone gas/particle separator which has been modified to let the concentrated solar energy enter through a windowless aperture. The reacting particles are directly exposed to the solar irradiation. Experimentation with a 60 kW reactor prototype was conducted at PSI's 90m² parabolic solar concentrator, in a continuous mode of operation. A counter-current flow heat exchanger was employed to preheat the reactants. Eighty five percent degree of calcination was obtained for cement raw material and 15% of the solar input was converted into chemical energy (enthalpy).The technical feasibility of the solar thermal decomposition of limestone was experimentally demonstrated. The use of solar energy as a source for high-temperature process heat offers the potential of reducing significantly the CO₂ emissions from lime producing plants. Such a solar thermochemical process can find application in sunny rural areas for avoiding deforestation.