Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

新型的治疗阿尔茨海默氏症药物(1-二甲基磷酰基-2,2,2-三氯)-乙基-1-醇烟酸醋对体外神经细胞的作用

目的: 观察本实验室合成的一种治疗阿尔茨海默氏症(AD)的药物(1-二甲基磷酰基-2, 2, 2 -三氯)-乙基^-1-醇烟酸醋(NMF),对体外培养的皮层神经细胞活性的影响以及对海人藻酸(KA)所致的神经损伤的保护作用。方法: 采用体外培养皮层神经元的方法,解剖分离 15 d胚胎小鼠皮层神经细胞, 接种于 96孔板,48 h 后加药并培养 72 h,以 MIT 法 观察 NMF 对小鼠皮层神经细胞活性的影响;同时将接种于 24 孔板的细胞预先给予 NMF,d 3 时加或不加KA处理后,以台盼蓝染色鉴别并计数死、活细胞,可得出细胞的存活率。结果: NMF 明显促进胎鼠皮层神经元活性,其中 NMF1、0. 1、10nmol·L^-1促进神经元活性增殖率分别高达 34.7%、37.4%、36. 7%, NMF 明显促进正常胎鼠皮层神经元存活卒,与对照组比较,10nmol·L^-1 NMF 对皮层神经元的存活率分别提高 39.3%、73.5%。 NMF能显著 对抗 KA 所致的神经元损伤,与 KA 损伤组相比, NMF0.1、10、10nmol·L^-1对损伤皮层神经元的保护率分别为 77.30%、80.10%、84.15%。结论: NMF 明 显促进胎鼠皮层神经元的洁性、提高正常皮层神经元,的存活卒,并能有效地保护KA所致的神经元损伤,提示 NMF 是一种很有潜力的治疗 AD 的药物。     

Theoretical Analysis for the Motion and Temperature of Melt Droplets in Spray Degassing Process

The motion of melt droplets in spray degassing process was analyzed theoretically. The height of the treatment tank in spray degassing process could be determined by the results of theoretical calculation of motion of melt droplets. To know whether the melt droplets would solidify during spraying process, the balance temperature of melt droplets was also theoretically analyzed. Then proof experiments for theoretical results about temperature of melt droplets were carried. In comparison, the experimental results were nearly similar to the calculation results.     

Growth Kinetics of Single Inclusion Particle in Molten Melts

On the basis of the single-particle framework, a new theory on inclusion growth in metallurgical melts is developed to study the kinetics of inclusion growth on account of reaction and collision. The studies show that the early growth of inclusion depends on reaction growth and Brawnian motion collision, and where the former is decisive, the late growth depends on turbulence collision and Stokes＇ collision, and where the former is dominant; collision growth is very quick during the smelting process, lessened in the refining process, but nearly negligible in the continuous casting process.     

An Easy Way to Quantify the Adhesion Energy of Nanostructured Cu/X(X=Cr,Ta,Mo,Nb,Zr) Multilayer Films Adherent to Polyimide Substrates

An approach based on film buckling under simple uniaxial tensile testing was utilized in this paper to quantitatively estimate the interfacial energy of the nanostructured multilayer films(NMFs) adherent to flexible substrates. The interfacial energies of polyimide-supported NMFs are determined to be *5.0 J/m2 for Cu/Cr, *4.1 J/m2 for Cu/Ta,*2.8 J/m2 for Cu/Mo, *1.1 J/m2 for Cu/Nb, and *1.2 J/m2 for Cu/Zr NMFs. Furthermore, a linear relationship between the adhesion energy and the interfacial shear strength is clearly demonstrated for the Cu-based NMFs, which is highly indicative of the applicability and reliability of the modified models.     

High-Speed Friction Stir Welding of SiC_p/Al–Mg–Si–Cu Composite

A 17 vol% SiCp/Al–Mg–Si–Cu composite plate with a thickness of 3 mm was successfully friction stir welded(FSWed) at a very high welding speed of 2000 mm/min for the first time. Microstructural observation indicated that the coarsening of the precipitates was greatly inhibited in the heat-affected zone of the FSW joint at high welding speed, due to the significantly reduced peak temperature and duration at high temperature. Therefore, prominent enhancement of the hardness was achieved at the lowest hardness zone of the FSW joint at this high welding speed, which was similar to that of the nugget zone. Furthermore, the ultimate tensile strength of the joint was as high as 369 MPa, which was much higher than that obtained at low welding speed of 100 mm/min(298 MPa). This study provides an effective method to weld aluminum matrix composite with superior quality and high welding efficiency.     

Three-Dimensional Growth of Coherent Ferrite in Austenite: A Molecular Dynamics Study

Coherent second phase often exhibits anisotropic morphology with specifi c orientations with respect to both the second and the matrix phases. As a key feature of microstructure, the morphology of the coherent particles is essential for understanding the second-phase strengthening eff ect in various industrial alloys. This letter reports anisotropic growth of coherent ferrite from austenite matrix in pure iron based on molecular dynamics simulation. We found that the ferrite grain tends to grow into an elongated plate-like shape, independent of its initial confi guration. The fi nal shape of the ferrite is closely related to the misfi t between the two phases, with the longest direction and the broad facet of the plate being, respectively, consistent with the best matching direction and the best matching plane calculated via the Burgers vector content(BVC) method. The strain energy calculation in the framework of Eshelby's inclusion theory verifi es that the simulated orientation of the coherent ferrite is energetically favorable. It is anticipated that the BVC method will be applicable in analysis of anisotropic growth and morphology of coherent second phase in other phase transformation systems.     

A STUDY OF TEMPERATURE-DEPENDENT VALENCE BOND STRUCTURE OF TITANIUM

On the basis of energy and shape method for the determination of the valence bond (VB) structures of crystal, the valence bond structure of titanium is redetermined at room temperature and calculated in the whole temperature range of 0-1943K. The outer shell electronic distribution of Ti is e_c~(2.9907) · (s_c~(0.4980) d_c~(2.4927)) ef1.0093 in crystal. The temperature dependences of the VB structures of hcp and bcc phases are the same. The VB structures of hcp and bcc phases monotonically increase or decrease with the increase in temperature, but show discontinuous changes at the phase-transformation temperature 1155K.     

Structural Optimization of Electromagnetic Swirling Flow in Nozzle of Slab Continuous Casting

During the slab continuous casting process, the flow field of molten steel in the mold plays a decisive role in the quality of the slab. In this paper, electromagnetic swirling flow in nozzle technology is proposed to control the flow field in mold.This technology can drive molten steel to rotate inside the submerged entry nozzle by electromagnetic force, thereby controlling the flow field. This research shows that it can reduce the impact of molten steel on the bottom of nozzle and partly reduce the negative pressure at the upper part of nozzle outlet which is even eliminated by optimizing the structure and angle of nozzle. The area of heat flux of the mold wall becomes larger, and the crest value of heat flux gets lower than that without swirling in nozzle and any nozzle optimization. The meniscus fluctuates smoothly, and the flow velocity at the top surface is within a reasonable range. The temperature field distribution in the mold is uniform which was beneficial to the growth of equiaxed crystal and decreased element segregation.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

FE Simulation of Center Crack Occurrence in Tube Rounds During Two-Roll Rotary

With the aid of FE (finite element) code MSC.Superform 2005, 2-D coupled thermo-mechanical simulation of center-crack occurrence in round billet during 2-roll rotary rolling process was presented using Oyane ductile fracture criteria. A simple modeling is put forward based on the spiral motion of the workpiece as an essential characteristic in movement. The influence of the feed angle and the entry cone angle of the main roll on the process was taken into account in the modeling. The soundness for simplifying the 3-D rotary rolling into a 2-D problem was discussed. By adopting the parameters of Diescher piercer in 140mm mandrel mill of Bao Steel, the distribution and development of strain / stress were analyzed, and the eigen value of ductile fracture as well. The critical percentage of diameter reduction was obtained from the simulation. The result showed a good agreement with the experimental value, and therefore was of widely guiding significance to the practical process for rationally formulating the deformation parameters of steel tube piercing.     

EFFECTS OF TREATMENT TIME ON CORROSION OF DIFFUSION-ALLOYED COATINGS OF PURE MAGNESIUM

The corrosion resistance of pure magnesium with surface alloying layer obtained by a solid diffusion alloying technique has been analyzed. To establish the optimum treatment time, the experiments were performed at 480℃ for different solid diffusion time (8, 16, and 24h). The diffusion interaction effectiveness between Zn, Al mix powder and the sample surface, depending on the treatment time for diffusion at given temperatures, has an obvious influence on corrosion resistance and corrosion mechanism. Corrosion properties were studied using the constant immersion test (in 3.0% NaCl solution, temperature is (28±1)℃, and time is 96h). Optical microscopy (OM) and EDS (energy dispersive spectrum) composition analysis were used to examine the cross-sectional microstructural characteristics of alloyed layer of treated samples. It is shown that in comparison with the untreated samples, the treated ones possess a better corrosion resistance. The Al5Mg11Zn4 phase, which formed as a continuous phase due to the diffusion of Al, Zn, and Mg elements and subsequent interaction on the outermost layer of diffusion alloying zones (especially the samples treated for 24h at 480℃), was inert to the chloride solution compared with pure magnesium and acted as a corrosion barrier, and therefore the best corrosion resistance was obtained. This protective action of A_(l5)Mg_(11)Zn_4 phase was found to change with its amount, which was controlled by the diffusion time at given temperature. It was concluded that the continuous A_(l5)Mg_(11)Zn_4 phase (WP-zone) of the reacted layer in pure magnesium was beneficial from the point of view of corrosion resistance.     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

Horizontally Solidified Al–3 wt%Cu–(0.5 wt%Mg) Alloys: Tailoring Thermal Parameters,Microstructure, Microhardness,and Corrosion Behavior

In the present experimental investigation, Al–3 wt%Cu and Al–3 wt%Cu–0.5 wt%Mg alloys castings are produced by a horizontal solidification technique with a view to examining the interrelationship among growth rate(G_R), cooling rate(C_R), secondary dendrite arm spacing(λ_2), Vickers microhardness(HV), and corrosion behavior in a 0.5 M NaCl solution.The intermetallic phases of the as-solidified microstructures, that is, h-Al_2Cu, S–Al_2CuMg, and x-Al_7Cu_2 Fe, are subjected to a comprehensive characterization by using calculations provided by computational thermodynamics software, optical microscopy, and scanning electron microscopy/energy-dispersive spectroscopy. Moreover, electrochemical impedance spectroscopy and potentiodynamic polarization tests have been applied to analyze the corrosion performance of samples of both alloys castings. Hall–Petch-type equations are proposed to represent the HV dependence on λ_2. It is shown that the addition of Mg to the Al–Cu alloy has led to a considerable increase in HV; however, the Al–Cu binary alloy is shown to have lower corrosion current density(i_(corr)) as well as higher polarization resistance as compared to the corresponding results of the Al–Cu–Mg ternary alloy.     

INDUSTRY NEWS

CITIC Dicastal aluminum wheel project launches in North America On Sept. 10, 2014, CITIC Group Corporation formally approved the aluminum wheel factory project of CITIC Dicastal Co., Ltd. in North America. Then, on Sept. 17, the incentive clauses of the project were approved by the State of Michigan, which signifies the project entering a comprehensive preparatory stage.     

SHENYAIV RESEARCH INSHTUTE OF FOUNDRY

正Established in 1957,Shenyang Research Institute of Foundry(SRIF)is the largest foundry institute in China.Foundry Institution of Chinese Mechanical Engineering Society,National Technical Committee 54 on Foundry of Standardization Administration of China(TC54),Productivity Promotion Center of Foundry Industry of China,and Supervision and Inspection Center of Molding Materials     

Information for Contributors

The Transactions of Nonferrous Metals Society of China, founded in 1991 and sponsored by The Nonferrous Metals Society of China, is published monthly now and mainly contains reports of original research which reflect the new progresses in the field of nonferrous metals science and technology, including mineral processing, extraction metallurgy, metallic materials and heat treatments, metal working, physical metallurgy, powder metallurgy, with the emphasis on fundamental science. It is the unique preeminent publication in English for scientists, engineers, under/post-graduates on the field of nonferrous metals industry. This journal is covered by many famous abstract/index systems and databases such as SCI Expanded, Ei Compendex Plus, INSPEC, CA, METADEX, AJ and JICST.     

Information for Contributors

The Transactions of Nonferrous Metals Society of China, founded in 1991 and sponsored by The Nonferrous Metals Society of China, is published monthly now and mainly contains reports of original research which reflect the new progresses in the field of nonferrous metals science and technology, including mineral processing, extraction metallurgy, metallic materials and heat treatments, metal working, physical metallurgy, powder metallurgy, with the emphasis on fundamental science. It is the unique preeminent publication in English for scientists, engineers, under/post-graduates on the field of nonferrous metals industry. This journal is covered by many famous abstract/index systems and databases such as SCI Expanded, Ei Compendex Plus, INSPEC, CA, METADEX, AJ and JICST.     

A Comparative Study of Artificial Neural Network and Response Surface Methodology for Optimization of Friction Welding of Incoloy 800 H

This article deals with the optimization of process parameters for friction welding of Incoloy 800 H rod and compares the results obtained by response surface methodology(RSM) and artificial neural network(ANN).The experiments were carried out on the basis of a five-level,four-variable central composite design.The output parameters were the tensile strength and burn-off length(BOL).They were considered as a function of four independent input variables,namely heating pressure(HP),heating time,upsetting pressure(UP),and upsetting time.The RSM results showed that the quadratic polynomial model depicted the interconnection between individual element and response.For optimizing the process parameters,ANN analysis was used,and the optimal configuration of the ANN model was found to be 4–9–2.For modeling aspect,a requisite trained multilayer perceptron neural network was rooted,and a quick propagation training algorithm was used to train ANN.The purpose of optimization was to decide the maximum tensile strength and minimum burn-off length of the welded joint which was done by varying the friction welding process variables.The order of importance of input parameters for friction welding of Incoloy 800 H was HP [ UP [ N [ BOL.After predicting the model using RSM and ANN,a comparison was made for predicting the effectiveness of two methodologies.By analyzing the results,it was observed that as compared to RSM,ANN model was more specific.