La2O3掺杂AgSnO2电接触材料的制备及性能研究

以Ag、Sn、La₂O₃粉为原料,采用机械合金法制备复合粉体。结合氧化法与粉末冶金工艺,对复合粉体进行氧化、压制、烧结。采用扫描电镜(SEM)和能谱仪、硬度计、金相显微镜、金属电导率测量仪等对复合粉体氧化前后的形貌以及电接触材料烧结前后的性能进行表征。结果表明：烧结后,电接触材料硬度较于烧结前明显下降。同时电接触材料随Sn含量增大,电阻率升高,密度反而下降。在一定的La₂O₃(0wt.%、0.75wt.%、1.5wt.%、2.25wt.%、3wt.%)含量范围内,La₂O₃掺杂量越高,密度越低。同时电接触材料经烧结后,随La₂O₃含量增加,其电阻率先降后升,在La₂O₃含量为0.75wt.%时,电接触材料的电阻率最低。     

网孔结构La2Sn2O7粉体的制备及其在Ag-电接触材料的制备及性能研究

以五水四氯化锡和硝酸镧为原料,采用化学共沉淀法在烧结温度920℃条件下合成了锡酸镧粉体。通过高能球磨法+成型烧结工艺制得Ag-La₂Sn₂O₇电接触复合材料。重点考察了胶凝剂浓度、烧结工艺对La₂Sn₂O₇粉体形貌及物相的影响,并对Ag- La₂Sn₂O₇电接触材料的物理性能进行了分析。研究结果表明：以碳酸氢铵为胶凝剂,于烧结温度920℃,2h条件下获得具有网孔结构的La₂Sn₂O₇粉体;于成型压力1200MPa,烧结温度900℃,6h条件下制得的Ag-La₂Sn₂O₇电接触材料表现出较佳的电阻率和硬度值。经过热挤压工艺,Ag-La₂Sn₂O₇电接触材料发生了大塑性变形,颗粒在热挤压过程中发生流动变形,形成类纤维状结构的排列分布状态,表现出更低的电阻率。     

SnO2 增强相对AgCuOIn2O3 电触头材料显微组织与性能的影响

采用反应合成法结合塑性变形工艺制备了不同SnO₂含量的AgCuOIn₂O₃SnO₂电触头材料,利用扫描电镜和金相显微镜表征了材料的微观形貌及显微组织,分析对比了不同SnO₂含量的材料金相组织及其增强相的分布均匀性,并利用X射线衍射分析了材料的物相结构。测量了材料的抗拉伸强度、硬度、电阻等性能。结果表明：添加适量的SnO₂能使组织中的孔隙尺寸缩小、其他缺陷明显减少。氧化物弥散分布在银基体中,极大地改善了AgCuOIn₂O₃电触头材料的显微组织均匀性。在SnO₂含量不变时,材料的电阻率随塑性变形程度增加而有所降低;随着SnO₂含量增多,电阻率呈现先降低后升高的趋势,最后趋于定值,约为2.4 μΩ·cm。添加SnO₂后各试样材料的硬度均显著升高,SnO₂含量为1%（质量分数）的材料具有最优的抗拉伸强度和延伸率。     

SnO2@TiO2核-壳纳米线的制备及其光催化性能研究

本文通过固-液-气(VLS)生长机制,利用化学气相沉积法(CVD)制备SnO₂纳米线。利用原子层沉积(ALD)以钛酸四异丙酯为前驱体在SnO₂纳米线表面沉积不同厚度的TiO₂壳层,形成SnO₂@TiO₂核-壳纳米线结构。通过中间Al₂O₃插层,分别制备出金红石和锐钛矿两种不同晶型的TiO₂,从而制备出两种不同复合结构的SnO₂@TiO₂核-壳纳米线。实验研究该复合结构中TiO₂的厚度与晶型对紫外光下光催化降解甲基橙溶液活性的影响。     

三元共晶成分Al2O3/YAG/ZrO2粉体及陶瓷的制备与组织性能研究

本文采用醇水共沉淀法制备了三元共晶成分Al₂O₃/YAG/ZrO₂粉体,在600-1350_oC温度范围煅烧后研究其物相转变过程。经1300_oC煅烧后Al₂O₃/YAG/ZrO₂共晶成分粉体的物相由α-Al₂O₃、c-ZrO₂和YAG构成,且具有α-Al₂O₃相包裹c-ZrO₂相的特殊结构。将煅烧粉体在1550_oC下热压烧结,制备具有内晶型结构的共晶成分Al₂O₃/YAG/ZrO₂复相陶瓷,其致密度、室温抗弯强度、断裂韧性和高温(1000_oC)抗弯强度分别为98.8%、420 MPa、3.69 MPa.m_1/2和464 MPa,并对复相陶瓷组织结构的形成机理进行了探讨。     

Al2O3/Ti2AlN复合材料在900℃,1000℃和1100℃空气中的氧化行为

利用综合热分析仪、背散射扫描电镜(BSE)和能谱分析(EDS)对Al₂O₃/Ti₂AlN复合材料在900 ℃,1 000 ℃和1 100 ℃/20 h空气中连续氧化20h后的氧化增重及氧化层截面进行了研究。结果表明：Al₂O₃/Ti₂AlN复合材料在空气中的氧化行为符合抛物线规律,在900 ℃,1 000 ℃和1 100 ℃/20 h氧化增重分别为2.78×10_-2 kg/m₂、10.4 ×10_-2 kg/m₂、21.9 ×10_-2 kg/m₂,抛物线速率常数相应为1.08×10_-8 kg₂/m₄s、1.44×10_-7 kg₂/m₄s、6.56×10_-7 kg₂/m₄s,氧化激活能为274 kJ/mol。氧化层主要由TiO₂和Al₂O₃组成的,连续的Al₂O₃次外层可以提高其抗氧化性能。氧化层结构的改变是由于氧化温度对Ti₄₊、Al₃₊由基体表面向外扩散和O_2-向内扩散的影响,以及TiO₂和Al₂O₃在不同温度下的形核生长速率导致的。对Al₂O₃/Ti₂AlN而言,控制材料与氧化气氛的界面是提高该材料抗氧化性能的关键。     

Fe2O3-CaO-TiO2 体系下铁酸钙的合成过程及TiO2 和CaTiO3 的影响

为了确定高钛型钒钛磁铁矿烧结过程中铁酸钙的生成是受TiO₂还是TiO₂和CaO形成的CaTiO₃影响,首先利用Fe₂O₃和CaO的纯试剂合成了铁酸钙,并研究了TiO₂和CaTiO₃对钛铁酸钙 （FCT） 形成的影响。在Factsage 7.0软件进行热力学计算的基础上,通过在空气气氛下进行烧结,获得了在1023~1423 K温度范围内、不同烧结时间的不同样品。通过X射线衍射和扫描电镜-能谱分析等表征手段,对烧结样品的物相转变和微观结构变化进行了表征。发现FCT的形成过程主要分为2个阶段：前一阶段为1023~1223 K温度范围内Fe₂O₃与CaO之间的反应,合成产物为Ca₂Fe₂O₅,反应方程式为“Fe₂O₃(s)+ 2CaO(s)= Ca₂Fe₂O₅(s)”;后一阶段为1223~1423 K温度范围内Ca₂Fe₂O₅和Fe₂O₃的反应,主要产物为CaFe₂O₄,反应为“Ca₂Fe₂O₅(s)+ Fe₂O₃(s)= 2CaFe₂O₄(s)”,该阶段尤其是温度为1423 K时,反应速率显著加快,随温度的升高CaTiO₃显著增加。然而,Ti元素在铁酸钙中的固溶很难实现,TiO₂与铁酸钙之间的反应不是形成FCT的有效途径。随着保温时间的延长,CaTiO₃和FCT相界中Fe元素含量增加。FCT主要是通过Fe组分在CaTiO₃中固溶形成的,主要反应是“Fe₂O₃+CaTiO₃(s)=FCT(s)”。     

BN/Al2O3 复合粉末及其聚合物基复合材料的制备与导热性能

采用固-液相共混法制备了多种BN/Al₂O₃复合粉末,通过冻融法和表面修饰法对BN进行了改性处理,改变表面修饰剂类型和摩尔比得到了前驱体和烧结态BN/Al₂O₃复合粉末,并利用机械混合法制备了聚合物基BN/Al₂O₃复合材料,并测试分析了其导热性能。结果表明,经冻融处理的BN分散性和界面相容性明显优于未经冻融处理的BN。多巴胺对BN的改性效果优于聚乙二醇。采用多巴胺作为表面修饰剂且BN与Al(NO₃)₃的摩尔比为1:1时,能够得到纳米Al₂O₃均匀包覆的微米BN粉末,即BN/Al₂O₃微纳复合粉末,其聚合物基复合材料的导热系数可达0.62 W·m^-1·K^-1,是纯聚合物导热系数的3倍,是采用纯微米BN粉末制备的聚合物基复合材料导热系数的1.5倍。在BN表面附着的Al₂O₃可以形成层状热传导通道,能够有效提高聚合物基BN/Al₂O₃复合材料的热导率。     

新型AgZrB2 触头材料的制备及电气性能

采用超声、球磨和放电等离子烧结相结合的方法制备了不同ZrB₂含量（3%,5%,7%,质量分数）的新型AgZrB₂触头材料,并通过电接触试验研究了触头材料的电弧侵蚀和材料转移行为。结果表明,ZrB₂含量显著影响AgZrB₂触头材料的耐电弧侵蚀性能。Ag-3% ZrB₂触头材料具有稳定的闭合/分断燃弧能量和持续时间,表现出较好的耐电弧侵蚀性能。但是,过多的ZrB₂会导致更高的闭合燃弧能量和更长的闭合燃弧时间,并且分断燃弧能量和时间会产生较大的波动,电弧侵蚀较为严重,这说明过量的ZrB₂不利于提高触头材料的耐电弧侵蚀性能。此外,Ag-3% ZrB₂和Ag-5% ZrB₂触头材料具有相同的材料转移模式——从阳极向阴极转移,而Ag-7% ZrB₂触头材料则呈现出相反的转移模式——从阴极向阳极转移。     

β-Ga2O3：B3+蓝色长余辉性能的研究

利用高温固相法制备了蓝色长余辉材料β-Ga₂O₃: B₃₊. β-Ga₂O₃: B₃₊在 260 nm紫外光辐照5分钟后,撤去紫外光,在380-600nm光谱范围内呈现宽带的蓝色余辉,余辉时间超过0.5小时。通过激发光谱,发射光谱,余辉衰减曲线,热释光谱等实验手段对样品进行表征。实验结果表明,B₃₊的掺入能够提高β-Ga₂O₃的发光性质。β-Ga₂O₃: 80% B₃₊的热释光谱表明B₃₊的掺入能够增加陷阱数目及陷阱深度。     

Effects of K2O-Li2O doping on surface and catalytic properties of Fe2O3/Cr2O3 system

The effects of K₂O and Li₂O-doping (0.5, 0.75 and 1.5 mol%) of Fe₂O₃/Cr₂O₃ system on its surface and the catalytic properties were investigated. Pure and differently doped solids were calcined in air at 400-600 °C. The formula of the un-doped calcined solid was 0.85Fe₂O₃:0.15Cr₂O₃. The techniques employed were TGA, DTA, XRD, N₂ adsorption at −196 °C and catalytic oxidation of CO oxidation by O₂ at 200-300 °C. The results revealed that DTA curves of pure mixed solids consisted of one endothermic peak and two exothermic peaks. Pure and doped mixed solids calcined at 400 °C are amorphous in nature and turned to α-Fe₂O₃ upon heating at 500 and 600 °C. K₂O and Li₂O doping conducted at 500 or 600 °C modified the degree of crystallinity and crystallite size of all phases present which consisted of a mixture of nanocrystalline α- and γ-Fe₂O₃ together with K₂FeO₄ and LiFe₅O₈ phases. However, the heavily Li₂O-doped sample consisted only of LiFe₅O₈ phase. The specific surface area of the system investigated decreased to an extent proportional to the amount of K₂O and Li₂O added. On the other hand, the catalytic activity was found to increase by increasing the amount of K₂O and Li₂O added. The maximum increase in the catalytic activity, expressed as the reaction rate constant (k) measured at 200 °C, attained 30.8% and 26.5% for K₂O and Li₂O doping, respectively. The doping process did not modify the activation energy of the catalyzed reaction but rather increased the concentration of the active sites without changing their energetic nature.     

SnO2含量对AgCuOSnO2电接触性能的影响

采用反应合成法制备了不同SnO2含量的AgCuOSnO2电接触材料。本文采用FQR-7501型涡流电导率仪测量抛光AgCuOSnO2的电导率。用扫描电镜(SEM)观察和研究了AgCuOSnO2电接触表面侵蚀形貌。JF04C直流数字电阻测试仪用于进行10000点测试。结果表明,AgCuO(10)SnO2(5)和AgCuO(10)SnO2(8)电触头材料在U=12V和I=15A时的接触电阻小于1.3mΩ,波动最小;当I=10A时,AgCuO(10)SnO2（x,x=2,5,8）的焊接力小于8cN,AgCuO(10)SnO2(5)电触头的焊接力较小当电流增大时稳定;当AgCuOSnO2电触头材料发生电弧烧蚀时,材料从阳极向阴极转移。随着SnO2含量的增加,材料传输过程中的损耗得到抑制和降低。所转移的电触头表面存在较少的气孔和微裂纹,表面形貌较为平坦。     

CaO-Bi2O3-MoO3-xNb2O5复合掺杂对高磁导率Mn-Zn铁氧体的微观结构和电磁性能的影响

采用高温固相反应制备了CaO-Bi_2O_3-MoO_3-XNb_2O_5(X=0.000%~0.075%,质量分数,步长:0.015%)复合掺杂的高磁导率Mn-Zn铁氧体材料,利用XRD、SEM、四探针电阻测试仪、阻抗分析仪、和软磁测试仪等分析测试手段对材料结构和性能进行表征,研究了复合掺杂剂中Nb_2O_5掺杂量对高磁导率Mn-Zn铁氧体材料的结构和电磁性能的影响。结果表明:当Nb_2O_5少量掺杂时,Nb_2O_5可以改善材料的微观结构,提高其密度、频率稳定性和品质因数,提高其电阻率,降低其体积功耗;当Nb_2O_5过量掺杂时,Nb_2O_5将恶化材料的微观结构,导致材料的电磁性能变差。当Nb2O5掺杂量为0.030%时材料的综合电磁性能最佳。     

Mechanochemical synthesis of Al2O3-TiB2 nanocomposite powder from Al-TiO2-H3BO3 mixture

Alumina-titanium diboride nanocomposite (Al₂O₃-TiB₂) was produced using mixtures of titanium dioxide, acid boric and pure aluminum as raw materials via mechanochemical process. The phase transformation and structural characterization during mechanochemical process were utilized by X-ray diffractometry (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and thermogravimetric analyses (TG-DTA) techniques. A thermodynamic appraisal showed that the reaction between TiO₂, B₂O₃ and Al is highly exothermic and should be self-sustaining. XRD analyses exhibited that the Al₂O₃-TiB₂ nanocomposite was formed after 1.5 h milling time. The results indicate that increasing milling time up to 40 h had no significant effect other than refining the crystallite size.     

CuInSe2 nano-crystallite reaction kinetics using solid state reaction from Cu2Se and In2Se3 powders

The reaction mechanism and CuInSe₂ formation kinetics using a solid state reaction from Cu₂Se and In₂Se₃ powders synthesized using a heating up process were investigated using X-ray diffractomy (XRD) and transmission electron microscopy (TEM). It was observed that the CuInSe₂ phase increased gradually, accompanied with a decrease in γ-In₂Se₃ with no intermediate phase as the calcination temperature and soaking time were increased. The reaction kinetics was analyzed using the Avrami and polynomial kinetic model, suggesting that CuInSe₂ formation from Cu₂Se and In₂Se₃ powders follows a diffusion-controlled reaction with an apparent activation energy of about 122.5-182.3 kJ/mol. Cu₂Se and In₂Se₃ phases react and directly transform into CIS without the occurrence of any intermediate phase and the size of the newly formed CuInSe₂ crystallites was close to that of the Cu₂Se reactant particle based on the TEM results, which indicated that the solid reaction kinetics may be dominated by the diffusion of In³⁺ ions.     

In-situ TiB2 and Al2O3 formation by DC plasma spraying

In-situ plasma spraying (IPS) is a promising process to fabricate composite coatings with in-situ formed thermodynamically stable phases. In the present study, mechanically alloyed Al-12Si, B₂O₃ and TiO₂ powder was deposited onto an aluminum substrate using atmospheric plasma spraying (APS). It has been observed that, during the coating process, TiB₂ and Al₂O₃ are in-situ formed through the reaction between starting powders and finely dispersed in hypereutectic Al-Si matrix alloy. Also, obtained results demonstrate that in-situ reaction intensity strongly depends on spray conditions.     

Modification of TiO2 nanorods by Bi2MoO6 nanoparticles for high performance visible-light photocatalysis

In this work, TiO₂ nanorods were prepared by a hydrothermal process and then Bi₂MoO₆ nanoparticles were deposited onto the TiO₂ nanorods by a solvothermal process. The nanostructured Bi₂MoO₆/TiO₂ composites were extensively characterized by X-ray diffraction, scanning and transmission electron microscopy, X-ray photoelectron spectroscopy and UV-vis diffuse reflectance spectroscopy. The photocatalytic activity of the Bi₂MoO₆/TiO₂ composites was evaluated by degradation of methylene blue. The Bi₂MoO₆/TiO₂ composites exhibit higher catalytic activity than pure Bi₂MoO₆ and TiO₂ for degradation of methylene blue under visible light irradiation (λ > 420 nm). Further investigation revealed that the ratio of Bi₂MoO₆ to TiO₂ in the composites greatly influenced their photocatalytic activity. The experimental results indicated that the composite with Bi₂MoO₆:TiO₂ = 1:3 exhibited the highest photocatalytic activity. The enhancement mechanism of the composite catalysts was also discussed.     

SNDC/La2Mo2O9复合电解质材料的制备及性能表征

本文采用甘氨酸-硝酸盐法(GNP)和溶胶凝胶法分别合成了Sm_0.1Nd_0.1Ce_0.8O_1.9(SNDC) 和La₂Mo₂O₉(LAMOX)粉末,并用常压烧结的方法制备了不同比例的SNDC和LAMOX的复合材料,通过XRD和SEM等手段表征了不同复合比例样品的物相和表面形貌并测试了烧结样品的电导率。结果表明,复合样品的电导率在相变点前后随着复合量增加变化趋势相反,其中LAMOX含量为20mol%的样品在550℃时的电导率能达到0.01S/cm,高于同温度下SNDC电导率。     

CVD deposition and characterization of coloured Al2O3/ZrO2 multilayers

Coloured Al₂O₃/ZrO₂ multilayers have been deposited onto WC-Co based inserts by a CVD process. Through physical as well as optical analysis of such multilayers, colour is believed to originate from interference. The coatings are obtained with good process reproducibility. It was found that the ZrO₂ process used in the multilayer, with ZrCl₄ as the only metal chloride precursor, results in a mixture of tetragonal and monoclinic ZrO₂ phases. However by adding a relatively small amount of AlCl₃ during such a process results in ZrO₂ layers being composed of predominantly tetragonal ZrO₂ phase. Corresponding multilayers seem to have a more fine grained and smoother morphology whereas multilayers containing monoclinic ZrO₂ phase seem to be less perfect with existence of larger grains of ZrO₂ which are believed to scatter light and alter the reflectance of such a multilayer. In addition to this, such multilayers were found to be free of or with greatly reduced amount of thermal cracks, normally present in pure CVD grown Al₂O₃ layers.It is believed that, in the studied Al₂O₃/ZrO₂ multilayers, the observed tetragonal ZrO₂ phase is the result of a size effect, where small enough ZrO₂ crystallites energetically favor the tetragonal phase. However as the ZrO₂ crystallite size distribution is shifted to larger sizes it is believed that a mixture of crystallites with both stable and metastable tetragonal phases as well as a stable monoclinic phase is obtained. The proposed metastable tetragonal ZrO₂ phase may in fact explain the absence of thermal cracks in such multilayers through a transformation toughening mechanism, well known in ZrO₂ based ceramics.