退火条件对Sn掺杂ZnO薄膜光电性能的影响

采用溶胶-凝胶法在普通载玻片上制备Sn掺杂ZnO薄膜(SZO薄膜)。研究空气退火、低真空退火、高真空退火、氮气退火、三高退火、循环退火6种不同退火条件对SZO薄膜光电性能的影响。结果表明:6种不同的退火条件制备的SZO薄膜均为纤锌矿结构且具有c轴择优取向生长的特性。高真空退火下,SZO薄膜的结晶状况和电学性质最优,最低电阻率可达到5.4×10~(-2)Ω·cm。薄膜的可见光区平均透过率均大于85%。薄膜在390nm和440nm附近(325nm光激发下)都出现光致发光峰,在空气、氮气、低真空中退火后薄膜440nm处发光强度最为显著。     

溅射Cu-Zn-Sn金属预制层后硫(硒)化法制备Cu2ZnSn(SxSe1-x)4薄膜及其光伏特性

采用溅射工艺制备Cu-Zn-Sn金属预制层并尝试在多种退火方案(硫化退火、硒化退火、不同温度下硫化后硒化)下对其进行退火处理,探索出一种只需采用金属预制层即可完成CZTSSe制备的退火工艺制度.通过扫描电镜对比研究了不同退火制度下Cu2ZnSn(SxSe1-x)4薄膜的形貌差异,发现低温硫化后硒化工艺可以有效减少因硫化温度过高引起的薄膜中孔洞较多的问题,有利于薄膜的平整与致密化.在此基础上,采用 X射线荧光光谱、扫描电镜、X 射线衍射及拉曼光谱对不同硫化温度(200 ℃、300℃、400 ℃、500 ℃)下硫化后硒化工艺制备的Cu2ZnSn(SxSe1-x)4薄膜的成分、形貌、物相结构及结晶性能进行了表征和分析.结果表明,300 ℃下硫化后硒化获得的Cu2ZnSn(SxSe1-x)4较其他温度下硫化后硒化获得的产物有着更好的形貌及结晶性能,其器件的光电转换效率为2.09%,远高于500 ℃下硫化后硒化工艺所得薄膜器件的效率(0.94%).     

溅射Cu-Zn-Sn金属预制层后硫(硒)化法制备Cu2ZnSn(SxSe1-x)4薄膜及其光伏特性

采用溅射工艺制备Cu-Zn-Sn金属预制层并尝试在多种退火方案(硫化退火、硒化退火、不同温度下硫化后硒化)下对其进行退火处理,探索出一种只需采用金属预制层即可完成CZTSSe制备的退火工艺制度。通过扫描电镜对比研究了不同退火制度下Cu_2ZnSn(S_xSe_(1-x))_4薄膜的形貌差异,发现低温硫化后硒化工艺可以有效减少因硫化温度过高引起的薄膜中孔洞较多的问题,有利于薄膜的平整与致密化。在此基础上,采用X射线荧光光谱、扫描电镜、X射线衍射及拉曼光谱对不同硫化温度(200℃、300℃、400℃、500℃)下硫化后硒化工艺制备的Cu_2ZnSn(S_xSe_(1-x))_4薄膜的成分、形貌、物相结构及结晶性能进行了表征和分析。结果表明,300℃下硫化后硒化获得的Cu_2ZnSn(S_xSe_(1-x))_4较其他温度下硫化后硒化获得的产物有着更好的形貌及结晶性能,其器件的光电转换效率为2.09%,远高于500℃下硫化后硒化工艺所得薄膜器件的效率(0.94%)。     

退火处理对掺锑Zn-Sn-O薄膜的特性的影响

首次在低温下采用磁控射频溅射技术在玻璃衬底上制备出具有多晶结构的掺锑锌-锡-氧(Zn-Sn-O:Sb)透明导电膜.研究了在通氧气氛制备薄膜的特性以及退火处理对制备薄膜结构和光电性能的影响.经真空退火后,氩氧混合气体溅射制备的Zn-Sn-O:Sb透明导电膜的最小电阻率为4×10-2Ω·cm,相应载流子浓度和霍尔迁移率分别为2.1×1019cm-3,8cm2·V-1·s-1.薄膜的可见光平均透过率达到了92.4%.薄膜具有较高的热稳定性和化学稳定性,对玻璃衬底有良好的附着性.     

功率和退火对磁控溅射生长ZnO∶Ga薄膜的影响

采用射频磁控溅射法在玻璃衬底上制备了ZnO∶Ga透明导电薄膜(GZO)。通过X射线衍射(XRD)、四探针电导率测试、紫外可见分光光度等表征方法研究了溅射功率对薄膜结晶特性及光电性能的影响。结果表明:当溅射功率180W时制备的GZO薄膜光电性能最优,方块电阻为9.8Ω/sq,电阻率为8.6×10-4Ω·cm,霍尔迁移率为12.5cm2/V·s,载流子浓度为5.8×1020cm-3,可见光透过率超过92%。另外,研究了最优制备条件下的GZO薄膜的高温稳定性,在氩气、氧气和真空气氛下分别对薄膜进行退火处理。结果表明,氩气退火的薄膜电学性能显著提高,是显著改善GZO薄膜性能的有效方法之一;氧气退火不利于薄膜的导电性;真空退火介于两者之间。     

PdSe2半导体薄膜的真空硒化法制备研究

PdSe₂薄膜主要通过机械剥离法和气相沉积法制得, 本研究采用一种简单有效的可在SiO₂/Si衬底上制备PdSe₂薄膜的方法。通过高真空磁控溅射技术在SiO₂/Si衬底上沉积一层Pd金属薄膜, 将Pd金属薄膜与Se粉封在高真空的石英管中并在一定的温度下进行硒化, 获得PdSe₂薄膜。根据截面高分辨透射电镜(HRTEM)照片可知PdSe₂薄膜的平均厚度约为30 nm。进一步研究硒化温度对PdSe₂薄膜电输运性能的影响, 当硒化温度为300 ℃时, 所制得的PdSe₂薄膜的体空穴浓度约为1×10¹⁸ cm^-3, 具有最大的室温迁移率和室温磁阻, 分别为48.5 cm²·V^-1·s^-1和12%(B=9 T)。值得注意的是, 本实验中通过真空硒化法获得的薄膜空穴迁移率大于通过机械剥离法制得的p型PdSe₂薄膜。随着硒化温度从300 ℃逐渐升高, 由于Se元素容易挥发, Pd薄膜的硒化程度逐渐减小, 导致薄膜硒含量、迁移率和磁电阻降低。本研究表明：真空硒化法是一种简单有效地制备PdSe₂薄膜的方法, 在贵金属硫族化合物的大面积制备及多功能电子器件的设计中具有潜在的应用价值。     

退火对硼掺杂微晶硅薄膜性能的影响

采用射频等离子体增强化学气相沉积(RFPECVD)法制备了不同硼烷掺杂比例的微晶硅薄膜.随后在不同温度、不同气氛下,对沉积得到的P型微晶硅薄膜进行了退火处理.研究发现,对初始晶化率较高的薄膜,退火后其晶化率发生下降;初始晶化率较低的薄膜,退火后其晶化率则有所提高;并且,在高真空中退火更有利于薄膜的晶化.退火后,薄膜表面...     

铜铟铝硒薄膜离子束溅射制备与表征

采用离子束溅射方法,在玻璃衬底上沉积Cu,In,Al和Se,在同一真空环境下进行退火处理,制备得到铜铟铝硒(CIAS)太阳电池吸收层薄膜。利用扫描电镜、X射线衍射仪、能谱仪、四探针系统、分光光度计分别对薄膜的表面形貌、物相结构、晶粒尺寸、元素含量、电阻率和禁带宽度等特性进行分析。结果表明:通过控制铜铟、Cu、Al、Se各靶材的镀膜时间,实现在Cu In Se2薄膜上掺杂Al元素,制备的CIAS薄膜呈现黄铜矿结构。薄膜(112)衍射峰峰位,表面电阻率和禁带宽度随着铝含量的增加而增加,调节Al元素的含量可以使薄膜表面均匀。当Al的原子分数比X(Al)=14.47%时,(112)衍射峰最强,半高宽最小,结晶最好。当X(Al)=11.8%,N(Al)/(N(In)+N(Al))=0.37,禁带宽度为2.12 e V,薄膜表面形貌最均匀。     

退火对ZnO/Cu/ZnO透明导电薄膜性能的影响

室温下利用磁控溅射制备了ZnO/Cu/ZnO透明导电薄膜,采用X射线衍射(XRD)、原子力显微镜(AFM)、扫描电子显微镜(SEM)、霍尔效应测量仪和紫外-可见分光光度计研究了薄膜的结构、形貌、电学及光学等性能与退火温度之间的关系。结果表明:退火前后薄膜均具有ZnO(002)择优取向,随着退火温度的升高,薄膜的晶化程度、晶粒粒径及粗糙度增加,薄膜电阻率先降低后升高,光学透过率和禁带宽度先升高后降低。150℃下真空退火的ZnO/Cu/ZnO薄膜的性能最佳,最高可见光透光率为90.5%,电阻率为1.28×10-4Ω·cm,载流子浓度为4.10×1021cm-3。     

热蒸发制备CdSe薄膜的退火工艺研究

采用真空热蒸发技术在光学玻璃基底上制备了CdSe薄膜,研究了真空下不同退火温度和退火时间对CdSe薄膜晶体结构和表面形貌的影响。XRD结果表明,在400~500℃范围下退火2h、5h的CdSe薄膜晶型不发生改变,结晶性随退火温度升高而增强,其晶粒尺寸从32nm增加至50nm。SEM结果表明,在450℃下退火2h后的CdSe薄膜表面颗粒分布均匀且排列规则、无裂纹。AFM结果表明,在450℃下退火2h后的CdSe薄膜致密性好,表面粗糙度低(5.19nm)。因此采用真空热蒸发制备的CdSe薄膜的热处理条件确定为:退火温度450℃,退火时间2h。     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Effect of Permeable Crystalline Material on Steel Reinforcement Corrosion of Concrete

Permeable crystalline materialcan permeate into pores and cracks of concrete and catalyze the reaction between Ca(OH) 2and unhydrated cement to generate a great quantity needle non-soluble crystals, which can stop up the pores and cracks of concrete, and increase the impermeability of concrete. This paper reported the results of a study conducted to evaluate steel reinforcement corrosion of concrete specimens uncoated and coated with permeable crystalline material as well as mixed with the permeable crystalline material. The properties evaluated for corrosion test were water impermeability, water absorption, compressive strength and potential. The results of water impermeability, water absorption, compressive strength clearly showed that the permeable crystalline material could prohibit water, any soluble salts and moisture from penetrating the concrete to cause corrosion, leaking, and other problems, and it did increase the compressive strength, which was favorable for protection of corrosion of reinforcing steel. Moreover, it was concluded from the potential-time curve that the steel reinforcement of uncoated specimen was in the state of activation whereas that of other specimens coated and mixed with the permeable crystalline material was in the state of inactivation. Above all, it was indicated that the permeable crystalline materialis very effective to protect the steel reinforcement of concrete from corrosion.     

The Research and Application About "Dry Peeling Off" Technology for Airplane Surface Paint Layer

In this paper, the principle of spurting take off lacquer were introduced; and with orthogonal method the unsaturate polyester was prepared ;it was easy to peel airplane paint layer off with this material and equipment.     

Quality Study of Honeycomb Core Shaping Without Wax Stabilization

Sandwich panels utilizing honeycomb cores result in lightweight, high-strength units that are very rigid. Indeed, they give honeycomb panels the best strength-to-weight ratio of any construction type available. Conventionally, the wax is poured into the cell of the core to strengthen the structure and prevent the core from being crushed during milling. Much time and labor is required to wax, mill, and clean the cores. In this study, the process of pouring wax into the core was skipped. In other words, the cutter directly milled the core. Experiments showed that the compressive strength of the core produced without wax stabilization was only 3% lower than that of cores produced using the traditional method. In addition, the drum peel strengths of cores produced without wax stabilization were 38.4% higher than cores produced using the traditional method, in which residual wax seriously polluted the adhesive. It was also found that eliminating the wax process can reduce costs.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

In-process thermal treatment of polylactic acid in fused deposition modelling

Polylactic acid (PLA) is one of the most widely used open source fused filament fabrication materials due to its ease of extrusion, biodegradability, and mechanical strength. The mechanical strength of PLA largely depends on the proper growth of its semi-crystalline structure, which can be severely impaired by a low rate of crystallization, particularly in open source printers. This can be further aggravated by the non-uniform thermal distribution of heat that causes improper curing among the extruded beads of the printing material. As a result, PLA printed on open source printers does not achieve the best mechanical properties. This research, for the first time, proposes an additive-free solution implemented through a detailed set of experimentation to improve the curing rate through in-process temperature variations to cure the joints among the beads. Scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy is used to confirm the improvements in the bead joints. This work is conducted in two phases of experiments. In the first phase, a full factorial ANOVA is used to investigate various process parameters and the important variables are used in the second phase to print test specimens in four different sets.