Ultra-low friction and excellent elastic recovery of fullerene-like hydrogenated carbon film based on multilayer design

Multilayer fullerene-like hydrogenated carbon (FL-C:H) films were synthesized by using the chemical vapour deposition technique with a different flow rate of methane. The typical fullerene-like structure of as-prepared films was investigated by using transmission electron microscopy and Raman spectra. The prepared multilayered FL-C:H films showed a high elastic recovery (\({\sim }\)90\(\%\)), ultra-low friction coefficient (\({\sim }\)0.019) and low wear rate \(({\sim }3.0\times 10^{-9}\,\hbox {mm}^{3}\,\hbox {Nm}^{-1})\) in humid air.     

Calorimetric Observation of Single $$\hbox {He}_2^*$$ Excimers in a 100-mK He Bath

We report the first calorimetric detection of individual \(\hbox {He}_2^*\) excimers within a bath of superfluid \(^4\hbox {He}\). The detector used in this work is a single superconducting titanium transition edge sensor (TES) with an energy resolution of \({\sim }1~\hbox {eV}\), immersed directly in the helium bath. \(\hbox {He}_2^*\) excimers are produced in the surrounding bath using an external gamma-ray source. These excimers exist either as short-lived singlet or long-lived triplet states. We demonstrate detection (and discrimination) of both states: In the singlet case the calorimeter records the absorption of a prompt \({\approx }15~\hbox {eV}\) photon, and in the triplet case the calorimeter records a direct interaction of the molecule with the TES surface, which deposits a distinct fraction of the \({\approx }15~\hbox {eV}\), released upon decay, into the surface. We also briefly discuss the detector fabrication and characterization.     

Characterization and optical properties of $$\hbox {Pr}_{2}\hbox {O}_{3}$$-doped molybdenum lead-borate glasses

\(\hbox {Pr}^{3+}\) doped molybdenum lead-borate glasses with the chemical composition 75PbO?[25–(x \(+\) y)\(\hbox {B}_{2}\hbox {O}_{3}]\)–\(y\hbox {MoO}_{3}\)–\(x\hbox {Pr}_{2}\hbox {O}_{3}\) (where \(x = 0.5\) and 1.0 mol% and \(y = 0\) and 5 mol%) were prepared by conventional melt-quenching technique. Thermal, optical and structural analyses are carried out using DSC, UV and FTIR spectra. The physical parameters, like glass transition \((T_{\mathrm{g}})\), stability factor \((\Delta T)\), optical energy band gap \((E_{\mathrm{gopt}})\), of these glasses have been determined as a function of dopant concentration. The \({T}_{\mathrm{g}}\) and optical energy gaps of these glasses were found to be in the range of 290–350\({^{\circ }}\hbox {C}\) and 2.45–2.7 eV, respectively. Stability of the glass doped with \(\hbox {Pr}^{3+}\) is found to be moderate (\(\sim \)40). The results are discussed using the structural model of Mo–lead-borate glass.     

Enhanced infrared transmission characteristics of microwave-sintered $$\hbox {Y}_{2}\hbox {O}_{3}$$–$$\hbox {MgO}$$MgO nanocomposite

Infrared (IR) transparent ceramics are found to have applications in demanding defence and space missions. In this work, \(\hbox {Y}_{2}\hbox {O}_{3}\)–\(\hbox {MgO}\) nanocomposites were synthesised by a modified single-step combustion technique. The characterisation of the as-prepared powder by X-ray diffraction and transmission electron microscopy revealed the presence of cubic phases of ultra-fine nanostructured \(\hbox {Y}_{2}\hbox {O}_{3 }\) and MgO, with an average crystallite size of \({\sim }19 \hbox { nm}\). For the first time the resistive and microwave heatings were effectively coupled for sintering the sample, and it was found that the sintering temperature and soaking time were reduced considerably. The pellets were sintered to 99.2% of the theoretical density at \(1430{^{\circ }}\hbox {C}\) for a soaking duration of 20 min. The well-sintered pellets with an average grain size of \({\sim }200 \hbox { nm}\) showed better transmittance properties relative to pure yttria. The promising percentage transmission of 80% in the UV–visible region and 82% in the mid-IR region shown by \(\hbox {Y}_{2}\hbox {O}_{3}\)–\(\hbox {MgO}\) nanocomposites can be tailored and made cost-effective to fabricate high-quality IR windows for strategic defence and space missions.     

Thermo-transport properties of Zn-substituted layered Li-nickel oxide, $$\hbox {LiNiO}_{2}$$

The layered Li-TM-\(\hbox {O}_{2}\) materials have been investigated extensively due to their application as cathodes in Li batteries. The electrical properties of these oxides can be tuned or controlled either by non-stoichiometry or substitution. Hence the thermo-transport properties of Zn-substituted \(\hbox {LiNi}_{1-x}\hbox {Zn}_{x}\hbox {O}_{2}\) for \(0 \le x \le 0.16\) have been investigated in the temperature range of 300–900 K for potential application as a high-temperature thermoelectric material. For \(x < 0.08\), the compounds were of single phase belonging to the space group R-3mH while for \(x > 0.08\) an additional minority phase, ZnO forms together with the main layered phase. All the compounds exhibit a semiconducting behaviour with electrical resistivity, varying in the range of  \(\sim 10^{-4}\) to \(10^{-2}\,\,\Omega \hbox {m}\) between 300 and 900 K. The electrical resistivity is found to increase with increasing Zn-substitution predominantly due to a decrease in the charge carrier hole mobility. The activation energy remains constant, \(\sim \)10  meV, with Zn-substitution. The Seebeck coefficient of the compounds is found to decrease with increasing temperature and increase with increasing Zn-substitution. The Seebeck coefficient decreases from \(\sim \)95 to \(35\ \upmu \hbox {V K}^{-1}\) and the corresponding power factor is \(\sim \)12\(\ \upmu \hbox {W m}^{-1}\ {\hbox {K}}^{-2}\) for the \(x = 0.16\) compound.     

Plastic crystal-incorporated magnesium ion conducting gel polymer electrolyte for battery application

Studies on a novel composition of magnesium ion conducting gel polymer electrolyte (GPE), comprising a solution of Mg-salt, magnesium trifluoromethanesulfonate (Mg-triflate or \(\hbox {Mg(Tf)}_{2})\) in a plastic crystal succinonitrile (SN), entrapped in a host polymer poly(vinylidenefluoride–hexafluoropropylene) (PVdF–HFP) was reported. Small amount of an ionic liquid, 1-ethyl-3-methylimidazolium trifluoromethanesulfonate (EMITf) was added to stabilize the GPE composition. The electrolyte possesses excellent dimensional integrity in the form of free-standing thick film, which offers the ionic conductivity of \(4 \times 10^{-3} \hbox { S } \hbox {cm}^{-1}\) at room temperature \({\sim }26{^{\circ }}\hbox {C}\). The electrochemical potential window of the electrolyte, observed from the linear sweep voltammetry, is determined to be \({\sim }4.1 \hbox { V}\). The magnesium ion conduction in the GPE film is confirmed from cyclic voltammetry, electrochemical impedance spectroscopy and dc polarization techniques. Different structural, thermal and electrochemical studies demonstrate the promising characteristics of the polymer film, suitable as electrolyte in rechargeable magnesium batteries. The potential of the GPE as electrolyte/separator was ascertained by fabricating a prototype magnesium battery of the configuration Mg:graphite composite \(\hbox {anode}/\hbox {GPE}/\hbox {MnO}_{2}\)-cathode. The specific discharge capacity of \(40 \hbox { mAh g}^{-1}\) (with respect to the \(\hbox {MnO}_{2}\) cathode material) was obtained at the first discharge. The cell shows charge–discharge performance for eight cycles with a substantial fading in capacity.     

Bootstrap in semi-functional partial linear regression under dependence

This paper deals with the semi-functional partial linear regression model \(Y={{\varvec{X}}}^\mathrm{T}{\varvec{\beta }}+m({\varvec{\chi }})+\varepsilon \) under \(\alpha \)-mixing conditions. \({\varvec{\beta }} \in \mathbb {R}^{p}\) and \(m(\cdot )\) denote an unknown vector and an unknown smooth real-valued operator, respectively. The covariates \({{\varvec{X}}}\) and \({\varvec{\chi }}\) are valued in \(\mathbb {R}^{p}\) and some infinite-dimensional space, respectively, and the random error \(\varepsilon \) verifies \(\mathbb {E}(\varepsilon |{{\varvec{X}}},{\varvec{\chi }})=0\). Naïve and wild bootstrap procedures are proposed to approximate the distribution of kernel-based estimators of \({\varvec{\beta }}\) and \(m(\chi )\), and their asymptotic validities are obtained. A simulation study shows the behavior (on finite sample sizes) of the proposed bootstrap methodology when applied to construct confidence intervals, while an application to real data concerning electricity market illustrates its usefulness in practice.     

Resistance-switching properties of Bi-doped $$\hbox {SrTiO}_{3}$$ films for non-volatile memory applications with different device structures

\(\hbox {SrTiO}_{3}\) and Bi-doped \(\hbox {SrTiO}_{3}\) films were fabricated with different device structures using the sol–gel method for non-volatile memory applications, and their resistance-switching behaviour, endurance and retention characteristics were investigated. \(\hbox {SrTiO}_{3}\) and \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films grown on Si or Pt have the same phase structure, morphologies and grain size; however, the grain size of the \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films grown on Si is slightly larger than those of the \(\hbox {SrTiO}_{3}\) films grown on Si and the \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films grown on Pt. The \(\hbox {SrTiO}_{3}\) or \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films grown on Si or Pt all exhibit bipolar resistive-switching behaviour and follow the same conductive mechanism; however, the \(\hbox {Ag}/\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}/\hbox {Si}\) device possesses the highest \(R_{\mathrm{HRS}}{/}R_{\mathrm{LRS}}\) of \(10^{5}\) and the best endurance and retention characteristics. The doping of Bi is conducive to enhance the \(R_{\mathrm{HRS}}{/}R_{\mathrm{LRS}}\) of the \(\hbox {SrTiO}_{3}\) films; meanwhile, the Si substrates help improve the endurance and retention characteristics of the \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films.     

Measurement of Out-of-Plane Thermal Conductivity of Epitaxial $$\hbox {YBa}_{2}\hbox {Cu}_{3}\hbox {O}_{7-{\delta }}$$ Thin Films in the Temperature Range from 10 K to 300 K by Photothermal Reflectance

We measured the out-of-plane (c-axis) thermal conductivity of epitaxially grown \(\hbox {YBa}_{2}\hbox {Cu}_{3}\hbox {O}_{7-{\delta }}\) (YBCO) thin films (250 nm, 500 nm and 1000 nm) in the temperature range from 10 K to 300 K using the photothermal reflectance technique. The technique enables us to determine the thermal conductivity perpendicular to a thin film on a substrate by curve fitting analysis of the phase lag between the thermoreflectance signal and modulated heating laser beam in the frequency range from \(10^{2}\,\hbox {Hz}\) to \(10^{6}\,\hbox {Hz}\). The uncertainties of measured thermal conductivity of all samples were estimated to be within \({\pm }9\,\%\) at 300 K, \({\pm }12\,\%\) at 180 K, \({\pm }16\,\%\) at 90 K and \({\pm }20\,\%\) below 50 K. The experimental results show that the thermal conductivity is dependent on the thickness of the thin films across the entire temperature range. We also observed that the thermal conductivity of the present YBCO thin films showed \(T^{1.4}\) to \(T^{1.6}\) glass-like dependence below 50 K, even though the films are crystalline solids. In order to explain the reason for this temperature dependence, we attempted to analyze our results using phonon relaxation times for possible phonon scattering models, including stacking faults, grain boundary and tunneling states scattering models.     

Study of the Choice of Excitation Frequency for Sub Surface Defect Detection in Electrically Thick Conducting Specimen Using Eddy Current Testing

Understanding the scope and limitations of non-destructive testing procedure is essential for selecting the appropriate test parameters for material inspection. This paper presents the scope of material (\( \delta_{s} \)) and probe dependent (\( \delta_{t} \)) penetration depths for determining the optimal test frequency (\( f_{opt} ) \) for detection of sub surface defects in electrically thick conducting specimens. Numerical modelling is carried out for a pancake coil above an electrically thick aluminium plate, \( t/\delta_{t} \)?>?1, to study the influence of the EC probe and defect location (\( t_{df} \)) on the test frequency for near and deep sub surface defects. The study concludes that the optimal test frequency, \( f_{opt} \) for detection of deep sub surface defects (\( t_{df} /t \approx 1 \)) is determined by the probe dependent skin depth, \( \delta_{t} \), and the plate thickness is related to \( f_{opt} \) by, \( t \propto 1/\sqrt {f_{opt} } \). The numerical observations were experimentally validated for machined sub surface notches on a 10 mm thick (\( t \)) aluminium plate.     

Synthesis,characterization and catalytic application of Ni catalysts supported on alumina–zirconia mixed oxides

Alumina and alumina–zirconia mixed oxides were compared as supports to prepare nickel catalysts. The oxides were prepared by the sol–gel method using aluminum tri-sec-butoxide and zirconium (IV) propoxide as precursors, and its physicochemical properties were determined by BET, TGA, DTA, XRD, SEM and TEM. The catalysts of nickel were obtained by the impregnation of the supports with nickel nitrate (10 wt%) and were heat-treated at \(700{^{\circ }}\hbox {C}\). The specific area of the supports and catalysts decreased with the increase in the zirconia content in agreement with the crystalline phase formed. TEM micrographs of nickel catalysts revealed particles in the size range of 10–30 nm. The \(\hbox {Ni/Al}_{2}\hbox {O}_{3}\)–\(\hbox {ZrO}_{2}\) catalysts were tested in the steam reforming reaction of ethanol (SRE) at \(500{^{\circ }}\hbox {C}\), and the obtained results suggest that the differences in catalytic activities depended on the content of \(\hbox {ZrO}_{2}\). The selectivity towards \(\hbox {H}_{2}\) was \({\sim }56\%\) for the named catalyst Ni–Al–0.25Zr.     

Study of $$\upbeta $$-phase development in spin-coated PVDF thick films

A study was conducted to ascertain the effect of variation in spin speed and baking temperature on \(\upbeta \)-phase content in the spin-coated poly(vinylidene fluoride) (PVDF) thick films (\({\sim }4{-}25\,\upmu \hbox {m}\)). Development of \(\upbeta \)-phase is dependent on film stretching and crystallization temperature. Therefore, to study the development of \(\upbeta \)-phase in films, stretching is achieved by spinning and crystallization temperature is adjusted by means of baking. PVDF films are characterized using Fourier transform infrared spectroscopy, X-ray diffraction, differential scanning calorimetry, and scanning electron microscopy. It is observed that crystallization temperature lower than \(60^{\circ }\hbox {C}\) and increase in spin speed increases the \(\upbeta \)-phase content in PVDF films. Crystallization temperature above \(60^{\circ }\hbox {C}\) reduces \(\upbeta \)-phase content and increases \(\upalpha \)-phase content. It was also observed that viscosity of the PVDF solution affects the \(\upbeta \)-phase development in films at a particular spin speed.     

Effect of annealing treatment on optical properties and microstructural variation of $$\hbox {WO}_{3}/\hbox {Ag}/\hbox {WO}_{3}$$ multilayer nano-films

Structural and optical properties of \(\text {WO}_{3}/\text {Ag}/\text {WO}_{3}\) nano-multilayer composites were investigated for heat mirror applications. \(\text {WO}_{3}/\text {Ag}/\text {WO}_{3}\) thin films were fabricated through a physical vapour deposition method by using electron-beam evaporation at the vacuum chamber at 10\(^{-5}\) Torr. \(\text {WO}_{3}\) nano-layer was fabricated at 40 nm. Annealing treatment was carried out at 100, 200, 300 and 400\(^{\circ }\)C for 1 h after the deposition of first layer of \(\text {WO}_{3}\) on the glass. On \(\text {WO}_{3}\) film, Ag nano-layers with 10, 12 or 14 nm thickness were deposited. Individual layers morphology was investigated using atomic force microscopy (AFM) and deduced that a smoother layer can be achieved after the annealing at 300\(^{\circ }\)C. Ellipsometry analysis was executed to determine both layers, Ag film thickness and inter-diffusion between the \(\text {WO}_{3}\)–Ag–\(\text {WO}_{3}\) layers. It was inferred that there was almost no interfering among the \(\text {WO}_{3}\)–\(\text {WO}_{3 }\) layers in the samples with 12 and 14 nm Ag thickness; while silver was deposited on the annealed \(\text {WO}_{3}\) layer at 300\(^{\circ }\)C. UV–visible spectrophotometer showed that the annealing treatment of the first \(\text {WO}_{3}\) layer enhanced the transparency of films in the visible region. The innovations of the present study have been based on the annealing of the films and finding an optimum thickness for the Ag film at 12–14 nm. Heat mirrors efficiency was assessed according to the principle of their optical behaviour and optimum performance obtained for 14 nm of Ag film, deposited on annealed tungsten oxide at 300\(^{\circ }\)C.     

Structural,microstructural and optical properties of $$\hbox {Cu}_{2}\hbox {ZnSnS}_{4}$$ thin films prepared by thermal evaporation: effect of substrate temperature and annealing

Thin films of \(\hbox {Cu}_{2}\hbox {ZnSnS}_{4}\) (CZTS), a promising solar cell absorber, were grown by thermal evaporation of ZnS, Sn and Cu precursors and subsequent annealing in sulphur atmosphere. Two aspects are chosen for investigation: (i) the effect of substrate temperature (\(T_{\mathrm{S}})\) used for the deposition of precursors and (ii) (\(\hbox {N}_{2}{+}\hbox {S}_{2})\) pressure during annealing, to study their impact on the growth of CZTS films. X-ray diffraction analysis of these films revealed the structure to be kesterite with (112) preferred orientation. Crystallite size is found to slightly increase with increase in \(T_{\mathrm{S}}\) as well as pressure during annealing. From optical absorption studies, the direct optical band gap of CZTS films is found to be \({\sim }\)1.45 eV. Room temperature electrical resistivity of the films obtained on annealing the stacks at 10 and 100 mbar pressures is found to be in the ranges 25–55 and 5–25 \(\Omega \) cm, respectively, depending on \(T_{\mathrm{S}}\). Films prepared by annealing the stack deposited at 300\({^{\circ }}\)C under 100 mbar pressure for 90 min are slightly Cu-poor and Zn-rich with compact grain morphology.     

Evaluation of the elastic properties of monovalent oxides using $$\hbox {TeO}_{2}$$-based glasses

Quaternary tellurite glasses with composition \(75\hbox {TeO}_{2}\)–\(5\hbox {WO}_{3}\)–\(15\hbox {Nb}_{2} \hbox {O}_{5}\)–\(5\hbox {M}_{x} \hbox {O}_{y}\) in mol%, where \(\hbox {M}_{x}\hbox {O}_{y}\) = (\(\hbox {Na}_{2}\hbox {O}, \, \hbox {Ag}_{2}\hbox {O}\), ZnO, MgO, CuO, NiO, \(\hbox {TiO}_{2}\), \(\hbox {MnO}_{2}\)), were prepared by the normal melt-quenching method. The ultrasonic velocities (longitudinal and shear) were measured in these glasses using the pulse-echo technique at room temperature. Their elastic moduli, microhardness and Debye temperature were calculated and discussed in terms of the modifier’s ionicity and quantitatively in terms of number of bonds per unit volume and the cross-link density. In this study, the values of ultrasonic velocities, elastic moduli, Debye temperature and microhardness were found to be strongly dependent on three factors, namely: (i) modifier’s ionicity; (ii) trigonal pyramid (\(\hbox {TeO}_{3}\))/trigonal bipyramid (\(\hbox {TeO}_{4}\)) ratio; and (iii) glass transition temperature \(T_\mathrm{g}\). We used the Makishima and Mackenzie’s model to calculate the theoretical elastic moduli and to indicate that the experimental values were in good agreement with the theoretical values.     

Rectifying resistance-switching behaviour of Ag/SBTO/STMO/$$\hbox {p}^{+}$$-Si heterostructure films

The \(\hbox {Sr}_{0.88}\hbox {Bi}_{0.12}\hbox {TiO}_{3}/\hbox {SrTi}_{0.92}\hbox {Mg}_{0.08}\hbox {O}_{3}\) (SBTO/STMO) heterostructure films were prepared on \(\hbox {p}^{+}\hbox {-Si}\) substrates by sol–gel spin-coating technique, and the films had good crystallinity and uniform grain distribution. The heterostructure films with a structure of Ag/SBTO/STMO/\(\hbox {p}^{+}\hbox {-Si}\) exhibited a bipolar, remarkable resistance-switching characteristic, and \(R_{\mathrm{HRS}}/R_{\mathrm{LRS}}\,\,{\sim }10^{4}\). More importantly, the heterostructure films showed rectifying characteristic in the low resistance state (LRS), and the rectification ratio can reach \(10^{2 }\) at \(\pm 1\hbox { V}\). The dominant resistive-switching conduction mechanism of high resistance state (HRS) was Ohmic behaviour, and the LRS changed to space charge-limited current (SCLC).     

In situ synthesis and properties of self-reinforced $$\hbox {Si}_{3} \hbox {N}_{4}\textendash \hbox {SiO}_{2}\textendash \hbox {Al}_{2} \hbox {O}_{3}\textendash \hbox {Y}_{2}\hbox {O}_{3} \ (\hbox {La}_{2}\hbox {O}_{3}$$) glass–ceramic composites

In-situ-grown \(\upbeta \!\hbox {-Si}_{3}\hbox {N}_{4}\)-reinforced \(\hbox {SiO}_{2}\textendash \hbox {Al}_{2}\hbox {O}_{3}\textendash \hbox {Y}_{2}\hbox {O}_{3}\) \((\hbox {La}_{2}\hbox {O}_{3})\) self-reinforced glass–ceramic composites were obtained without any \(\upbeta \!\hbox {-Si}_{3}\hbox {N}_{4}\) seed crystal. These composites with different compositions were prepared in a nitrogen atmosphere for comparison of phase transformation and mechanical properties. The results showed that \(\hbox {SiO}_{2}\textendash \hbox {Al}_{2}\hbox {O}_{3}\textendash \hbox {Y}_{2}\hbox {O}_{3}\) \((\hbox {La}_{2}\hbox {O}_{3})\) glass can effectively promote \(\upalpha \)- to \(\upbeta \!\hbox {-Si}_{3}\hbox {N}_{4}\) phase transformation. The crystallized \(\hbox {Y}_{2}\hbox {Si}_{2}\hbox {O}_{7}\textendash \hbox {La}_{4.67}\hbox {Si}_{3}\hbox {O}_{13}\) phases with a high melting point significantly benefited the high-temperature mechanical properties of the composites. The \(\hbox {Si}_{3}\hbox {N}_{4}\textendash \hbox {SiO}_{2}\textendash \hbox {Al}_{2} \hbox {O}_{3}\textendash \hbox {Y}_{2}\hbox {O}_{3}\) \((\hbox {La}_{2}\hbox {O}_{3})\) glass–ceramic composites exhibit excellent mechanical properties compared with unreinforced glass–ceramic matrix, which is undoubtedly attributed to the elongated \(\upbeta \!\hbox {-Si}_{3}\hbox {N}_{4}\) grains. These glass–ceramic \(\hbox {Si}_{3}\hbox {N}_{4}\) composites with excellent comprehensive properties might be a promising material for high-temperature applications.     

Influence of $$\hbox {TiO}_{2}$$ particle size and conductivity of the CuCrO$$_{2}$$2 nanoparticles on the performance of solid-state dye-sensitized solar cells

Solid-state dye-sensitized solar cells have been fabricated with mesoporous \(\hbox {TiO}_{2 }\) photoanode and N719 dye as photosensitizer. First, \(\hbox {TiO}_{2}\) and non-doped, Zn- and Mg-doped CuCrO\(_{2}\) nanoparticles have been synthesized by sol–gel method. In addition, the \(\hbox {TiO}_{2}\) pastes have been prepared through Pechini-type sol–gel method. The effect of \(\hbox {TiO}_{2}\) particle size, mesoporous \(\hbox {TiO}_{2}\) photoanode thickness and solid-state electrolyte thickness on the efficiency of the fabricated devices has been investigated. Our results show that in spite of the low amount of dye loading for photoanode with large \(\hbox {TiO}_{2}\) nanoparticles (80–180 nm), the dye-sensitized solar cell made from it has higher efficiency than that constructed from the photoanode comprising of small particles about 10–15 nm in size. The higher efficiency is attributed to the longer diffusion length of electrons because of a better electron transport and penetration of a large amount of \(\hbox {CuCrO}_{2 }\) nanoparticles in the porous structure of \(\hbox {TiO}_{2}\) photoanode. By using the doped \(\hbox {CuCrO}_{2}\) nanoparticles, the efficiency has been increased from 0.027% for \(\hbox {TiO}_{2}\)/N719 dye/CuCrO\(_{2}\) to 0.033% for \(\hbox {TiO}_{2}\)/N719 dye/CuCrO\(_{2}\):Zn and further increased to 0.042% for \(\hbox {TiO}_{2}\)/N719 dye/CuCrO\(_{2}\):Mg. The efficiency enhancement by doping is ascribed to the conductivity improvement due to the presence of impurity atoms.     

Electrochemical impedance studies of capacity fading of electrodeposited ZnO conversion anodes in Li-ion battery

Electrodeposited ZnO coatings suffer severe capacity fading when used as conversion anodes in sealed Li cells. Capacity fading is attributed to (i) the large charge transfer resistance, \(R_{\mathrm{ct}}\) (300–700 \(\Omega \)) and (ii) the low \(\hbox {Li}^{+}\) ion diffusion coefficient, \(D_{\mathrm{Li}}^{+}\ (10^{-15}\) to \(10^{-13}\hbox { cm}^{2}\hbox { s}^{-1})\). The measured value of \(R_{\mathrm{ct}}\) is nearly 10 times higher and \(D_{\mathrm{Li}}^{+}\) 10–100 times lower than the corresponding values for \(\hbox {Cu}_{2}\hbox {O}\), which delivers a stable reversible capacity.