A 0.8‐V supply bulk‐driven operational transconductance amplifier and Gm‐C filter in 0.18 µm CMOS process

A low voltage bulk‐driven operational transconductance amplifier (OTA) and its application to implement a tunable Gm‐C filter are presented. The linearity of the proposed OTA is achieved by nonlinear terms cancelation technique, using two paralleled differential topologies with opposite signs in the third‐order harmonic distortion term of the differential output current. The proposed OTA uses 0.8 V supply voltage and consumes 31.2 μW. The proposed OTA shows a total harmonic distortion of better than ?40 dB over the tuning range of the transconductance, by applying 800 mV_ppd sine wave input signal with 1 MHz frequency. The OTA has been used to implement a third‐order low‐pass Gm‐C filter, which can be used for wireless sensor network applications. The filter can operate as the channel select filter and variable gain amplifier, simultaneously. The gain of the filter can be tuned from ?1 to 23 dB, which results in power consumptions of 187.2 to 450.6 μW, respectively. The proposed OTA and filter have been simulated in a 0.18 µm CMOS technology. Simulations of process corners and temperature variations are also included in the paper. Copyright © 2014 John Wiley & Sons, Ltd.     

Analysis and design of highly linear triode‐mode based OTA and its application to a wide tunable Gm‐C filter

In this paper, a new highly linear operational transconductance amplifier (OTA) based on triode‐mode input transistors is introduced. An analysis based on theoretical relations and simulation results is presented that aims to obtain the best operating points of triode‐mode and cascode transistors to achieve the highest linearity. The proposed analysis is utilized to design a linear pseudo‐differential OTA, benefiting a linear common mode feedforward and an appropriate common mode feedback circuit. The common mode feedforward circuit is also regulated in the same manner as main the transconductor to stabilize the output common mode voltage during tuning action and achieve higher common mode rejection ratio. Proposed OTA is used to implement a tunable low‐power linear Gm‐C filter. The cutoff frequency of the filter is tunable from 2.7 to 44 MHz while its power consumption changes from 3.5 to 8.5 mW in the entire tuning range. By applying input voltages up to 1.1 Vp‐p, the filter's IM3 remains less than −48 dB for various cutoff frequencies. The proposed OTA and filter are simulated in 0.18‐μ m CMOS technology with Hspice simulator. Copyright © 2017 John Wiley & Sons, Ltd.     

Multiple output differential OTA with linearizing bulk‐driven active‐error feedback loop for continuous‐time filter applications

A CMOS circuit realization of a highly linear multiple‐output differential operational transconductance amplifier (OTA) has been proposed. The presented approach exploits a differential pair as an input stage with both the gate and the bulk terminals as signal ports. For the proposed OTA, improved linearity is obtained by means of the active‐error feedback loop operating at the bulk terminals of the input stage. SPICE simulations of the OTA show that, for 0.35 µm AMS process, total harmonic distortion at 1.36Vpp is less than 1% with dynamic range equal to 60.1 dB at power consumption of 276 μW from 3.3 V supply. As an example, both single output and dual differential OTAs are used to design third‐order elliptic low‐pass filters. The cut‐off frequency of the filters is 1 MHz. The power consumption of the OTA‐C filter utilizing the dual output differential OTA is reduced to 1.24 mW in comparison to 2.2 mW consumed by the single output differential OTA‐C filter counterpart. Copyright © 2014 John Wiley & Sons, Ltd.     

Analysis and implementation of a fourth‐order bandpass filter for R‐wave detection of an implantable cardiac microstimulator

This paper presents an ultra‐low‐power fourth‐order bandpass operational transconductance amplifier‐C (OTA‐C) filter for an implantable cardiac microstimulator used to detect the R‐wave of intracardiac electrograms. The OTA‐C filter fabricated by TSMC 0.35‐µm complementary metal–oxide–semiconductor (CMOS) technology is operated in the subthreshold region to save power under a supply voltage of 1 V. The current cancellation technique is adopted to reduce the transconductance of the amplifier. Through this, the low‐frequency OTA‐C filter can be realized by ultra‐low transconductance with on‐chip capacitors. Direct comparison to conventional RLC ladders replaced by OTA‐C circuits shows that the method of reducing the number of OTAs further diminishes power consumption. Design issues, including ultra‐low transconductance, linearity, and noise, are also discussed. Measurement results show that the low‐voltage, low‐power filter has a bandwidth between 10 and 50 Hz, third inter‐modulation distortion of ?40 dB, dynamic range of 43 dB, and power consumption of only 12 nW. The real electrocardiography signal is fed into the bandpass filter to verify the function of signal processing with the distribution of the R‐wave. Copyright © 2012 John Wiley & Sons, Ltd.     

0.5‐V bulk‐driven OTA and its applications

A new 0.5‐V bulk‐driven operational transconductance amplifier (OTA), designed in 50 nm CMOS technology, is presented in the paper. The circuit is characterized by improved linearity and dynamic range obtained for MOS devices operating in moderate inversion region. Some basic applications of the OTA such as a voltage integrator and a second‐order low‐pass filter have also been described. The filter is compared to other low‐voltage filters presented in the literature. Copyright © 2013 John Wiley & Sons, Ltd.     

Explicit design formulas for current‐mode leap‐frog OTA‐C filters and 300 MHz CMOS seventh‐order linear phase filter

The leap‐frog (LF) configuration is an important structure in analogue filter design. Voltage‐mode LF OTA‐C filters have recently been studied in the literature; however, general explicit formulas do not exist for current‐mode LF OTA‐C filters and there is also need for current‐mode LF‐based OTA‐C structures for realization of arbitrary transmission zeros. Three current‐mode OTA‐C structures are presented, including the basic LF structure and LF filters with an input distributor or an output summer. They can realize all‐pole characteristics and functions with arbitrary transmission zeros. Explicit design formulas are derived directly from these structures for the synthesis of, respectively, all‐pole and arbitrary zero filter characteristics of up to the sixth order. The filter structures are regular and the design formulas are straightforward to use. As an illustrative example, a 300 MHz seventh‐order linear phase low‐pass filter with zeros is presented. The filter is implemented using a fully differential linear operational transconductance amplifier (OTA) based on a source degeneration topology. Simulations in a standard TSMC 0.18µm CMOS process with 2.5 V power supply have shown that the cutoff frequency of the filter ranges from 260 to 320 MHz, group delay ripple is about 4.5% over the whole tuning range, noise of the filter is 420nA/√Hz, dynamic range is 66 dB and power consumption is 200 mW. Copyright © 2008 John Wiley & Sons, Ltd.     

Rail-to-rail input/output operational transconductance amplifier (OTA) with high CMRR and PSRR

This paper introduces a low-voltage CMOS operational transconductance amplifier (OTA) with rail-to-rail input/output stages. Input stage uses floating gate transistors to realize rail-to-rail scheme. However, this scheme gives rise to reduction in transconductance of the OTA. To increase transconductance (G _m), an effective partial positive feedback is used. Class AB output stage is so designed that improves the gain, slew rate, common mode rejection ratio and maximum swing of the OTA. With ±0.75 v power supply, this OTA consumes the low power of 397.5?μw. G _m variation of input stage is 0.004% for rail-to-rail (±0.75 v) variation in common mode input signals and reaches to 0.036% beyond the rail-to-rail range (±1 v) which is a superior result compared with previously reported works. As is proved by theoretical relations and simulation results, proposed auxiliary circuit for rail-to-rail operation results in both high CMRR due to fixing common source node of input differential pair and high linearity due to attenuation of input signals. Simulation results show that CMRR in DC frequency is 259.5 dB and HD3 is ?46 dB for 2.15 v_P-P differential output voltage signal with applying a 0.48 v_P-P input signal at 1 MHz. Proposed OTA is simulated in TSMC 0.18 μm CMOS technology with Hspice. Monte Carlo simulation results are included to forecast mismatch effects after fabrication process.     

On the input common‐mode voltage range of CMOS bulk‐driven input stages

In this paper the response of a bulk‐driven MOS Metal‐Oxide‐Semiconductor input stage over the input common‐mode voltage range is discussed and experimentally evaluated. In particular, the behavior of the effective input transconductance and the input current is studied for different gate bias voltages of the input transistors. A comparison between simulated and measured results, in standard 0.35‐µm CMOS Complementary Metal‐Oxide‐Semiconductor technology, demonstrates that the model of the MOS transistors is not sufficiently accurate for devices operating under forward bias conditions of their source‐bulk pn junction. Therefore, the fabrication and the experimental evaluation of any solution based on this approach are highly recommended. A technique to automatically control the gate bias voltage of a bulk‐driven differential pair is proposed to optimize the design tradeoff between the effective input transconductance and the input current. The proposed input stage was integrated as a standalone block and was also included in a 1.5‐V second‐order operational transconductance amplifier (OTA)‐C lowpass filter. Experimental results validate the effectiveness of the approach. Copyright © 2010 John Wiley & Sons, Ltd.     

A novel feed-forward compensation technique for single-stage fully-differential CMOS folded cascode rail-to-rail amplifier

This paper presents a novel active and passive mixed feed-forward compensation technique for single-stage CMOS folded-cascode rail-to-rail operational trans-conductance amplifiers (OTA). Simulations using 0.5 μm Agilent CMOS process parameters indicate a phase margin of around 82° with an unity gain bandwidth of 320 MHz (@1.17 pF capacitive load including the device parasitics). Also, the compensated OTA provided over 60 dB DC-gain with rail-to-rail output voltage swing as well as wide input common-mode range. This ensures optimum step response (fast and accurate settling without ringing) for the feedback amplifier in switched-capacitor signal processing applications. An improved ``fast sensing' common-mode feedback circuit with high common-mode gain is also used for the single-stage cascode OTA.     

Design methodology for common‐mode stability of OTA‐based gyrators

This paper presents a design methodology for common‐mode (CM) stability of operational transconductance amplifier (OTA)‐based gyrators. The topology of g_m ? C active inductors is briefly reviewed. Subsequently, a comprehensive mathematical analysis on the CM stability of OTA‐based gyrators is presented. Sufficient requirements for the gyrator's CM stability, which easily can be considered during the design process of common‐mode feedback (CMFB) amplifiers, are defined. Based on these stability requirements, a design methodology and a design procedure are proposed. Finally, in order to validate the proposed procedure, a resonator with 20 MHz resonance frequency and a quality factor of 20 is fabricated with UMC 180 nm complementary metal‐oxide‐semiconductor technology, and its CM stability is examined. Copyright © 2015 John Wiley & Sons, Ltd.     

High-gain,high-CMRR class AB operational transconductance amplifier based on the flipped voltage follower

A novel class AB operational transconductance amplifier (OTA) topology is proposed, based on a class AB flipped voltage follower. The OTA has class AB behavior, with current boosting both for the load and the compensation capacitors. It has a high gain of (g_mr₀)⁴ , obtained using a two-stage structure with cascoded stages, and is a two-stage Miller-compensated amplifier employing multipath to remove the positive zero. It has close to rail-to-rail output swing (limited by cascoding) and very low common-mode gain thanks to a replica technique (allowing the use of low-power common-mode feedback [CMFB] loops). Ninety-two decibels of gain and 176 dB of common-mode rejection ratio (CMRR) without CMFB are achieved using a 40-nm complementary metal-oxide semiconductor (CMOS) process. The OTA is used to design a low-power sample-and-hold amplifier (SHA) operating at 5 MSps, a typical application for CMOS OTAs, which has been chosen to verify the proposed circuit's performance and to show that the OTA is robust in Monte Carlo simulations under process variations and mismatches in an actual application.     

Analytical synthesis and comparison of voltage‐mode Nth‐order OTA‐C universal filter structures

Complementary single‐ended‐input operational transconductance amplifier (OTA)‐based filter structures are introduced in this paper. Through two analytical synthesis methods and two transformations, one of which is to convert a differential‐input OTA to two complementary single‐ended‐input OTAs, and the other to convert a single‐ended‐input OTA and grounded capacitor‐based one to a fully differential OTA‐based one, four distinct kinds of voltage‐mode nth‐order OTA‐C universal filter structures are proposed. TSMC H‐Spice simulations with 0.35µm process validate that the new complementary single‐ended‐input OTA‐based one holds the superiority in output precision, dynamic and linear ranges than other kinds of filter structures. Moreover, the new voltage‐mode band‐pass, band‐reject and all‐pass (except the fully differential one) biquad structures, all enjoy very low sensitivities. Both direct sixth‐order universal filter structures and their equivalent three biquad stage ones are also simulated and validated that the former is not absolutely larger in sensitivity than the latter. Finally, a very sharp increment of the transconductance of an OTA is discovered as the operating frequency is very high and leads to a modified frequency‐dependent transconductance. Copyright © 2010 John Wiley & Sons, Ltd.     

Super class AB OTA without open‐loop gain degradation based on dynamic cascode biasing

A scheme to achieve simultaneously extremely high slew‐rate improvement and avoiding open‐loop gain degradation in one‐stage super class AB op‐amps is introduced. It overcomes the serious shortcoming of super class AB operational transconductance amplifiers that shows very high‐output current enhancement factors at the expense of degrading the open‐loop gain. The proposed scheme uses dynamically biased cascode transistors to avoid gain and slew‐rate degradation. Experimental results of a super class AB operational transconductance amplifier in 180‐nm complementary metal‐oxide semiconductor technology with open‐loop gain of 67 dB, a factor 2 improvement in GBW , and a current enhancement factor of 270 verify the proposed scheme. Copyright © 2017 John Wiley & Sons, Ltd.     

A 40 M–1000 MHz 77.2‐dB spurious free dynamic range CMOS RF variable gain amplifier for digital TV tuner ICs

In this paper, a 40 M–1000 MHz 77.2‐dB spurious free dynamic range (SFDR) CMOS RF variable gain amplifier (VGA) has been presented for digital TV tuner applications. The proposed RFVGA adopts a wideband operational‐amplifier‐based VGA and a wideband buffer with differential multiple gated transistor linearization method for wideband operation and high linearity. The SFDR of the proposed RFVGA is also analyzed in detail. Fabricated in a 0.13‐µm CMOS process, the RFVGA provides 31‐dB gain range with 1‐dB gain step, a minimum noise figure of 7.5 dB at a maximum gain of 27 dB, and maximum in‐band output‐referred third‐order intercept point of 27.7 dBm, while drawing an average current of 27.8 mA with a supply voltage of 3.3 V. The chip core area is 0.54 mm × 0.4 mm. Copyright © 2014 John Wiley & Sons, Ltd.     

高速流水线ADC中跨导放大器设计及误差分析

应用于8 bit,1.5 bit/级,100 M采样率,高速流水线型ADC的OTA放大器设计及实现,重点分析OTA放大器的非线性,如增益非线性、不完全建立误差对高速、低功耗ADC性能的影响,并使用MATLAB建模验证分析结果。OTA放大器采用功耗较低的套筒型共源共栅放大器基本结构,通过增益提高技术提高放大器增益,采用共模反馈消除各类不匹配带来的误差。从仿真结果上看,OTA放大器增益大于80 dB,单位增益带宽为960.5 MHz,建立时间为4.87 ns。实现的高速流水线型ADC,经仿真测试DNL为0.7 LSB,INL为1.02 LSB,符合设计要求。     

Low‐voltage rail‐to‐rail switched buffer topologies

This paper presents some CMOS rail‐to‐rail low‐voltage (1.2 V) switched buffer topologies, to be used as input stages in switched‐opamp circuits. The main buffer is based on the use of an op‐amp featuring rail‐to‐rail input and output swing with constant transconductance over the input common mode voltage. The designed buffer exhibits a total harmonic distortion of about ‐61 dB for 5 MHz clock frequency with 2 V_pp input amplitude. Its characteristics have been compared with those of other rail‐to‐rail switched buffers, based on the main CMOS OTA (simple, symmetrical, Miller), showing good distortion even at frequencies in the MHz range and satisfying the requirements for the series switches. Copyright © 2001 John Wiley & Sons, Ltd.     

0.6-V CMOS cascode OTA with complementary gate-driven gain-boosting and forward body bias

An innovative low-voltage low-power complementary metal-oxide-semiconductor (CMOS) gain boosting approach is presented. It exploits complementary gate-driven gain boosting and adopts forward body bias, resulting in the minimum possible supply requirement of one threshold plus two saturation voltages, without requiring any additional current branch. The solution is also exploited in a rail-to-rail high-performance single-stage cascode operational transconductance amplifier (OTA). Simulations using a 40-nm process with thresholds around 0.45 V show that 0.6 V and 50 μA are adequate to supply the designed OTA, which exhibits a 60-dB direct current (DC) gain, a 45-MHz unity-gain frequency, and an 18-V/μs slew rate, under a 1-pF load.     

Using MOS current dividers for linearization of programmable gain amplifiers

Two highly linear, digitally programmable gain amplifiers are presented and compared in terms of linearity, frequency, area and power consumption. High linearity and wide gain tuning range with moderate area consumption are the main benefits of both configurations. Furthermore, constant bandwidth is achieved by means of switched compensation capacitor arrays. Three‐bit prototypes were integrated in a 0.35 µm–3.3 V CMOS process with 2.5 V supply voltage. Experimental distortion levels are better than ?68 dB for 1 MHz and 1 V_p?p output signals in both configurations; hence, the suitability of the linearization technique based on MOS current dividers is shown. Copyright © 2007 John Wiley & Sons, Ltd.     

0.5‐V bulk‐driven differential amplifier

A new 0.5‐V fully differential amplifier is proposed in this article. The structure incorporates a differential bulk‐driven voltage follower with conventional gate‐driven amplification stages. The bulk‐driven voltage follower presents differential gain equal to unity while suppressing the input common‐mode voltage. The amplifier operates at a supply voltage of less than 0.5 V, performing input transconductance almost equal to a gate transconductance and relatively high voltage gain without the need for gain boosting. The circuit was designed and simulated using a standard 0.18‐µm CMOS n‐well process. The low‐frequency gain of the amplifier was 56 dB, the unity gain bandwidth was approximately 3.2 MHz, the spot noise was 100 nV/√Hz at 100 kHz and the current consumption was 90 μΑ. Copyright © 2012 John Wiley & Sons, Ltd.     

Global impedance attenuation network for multistage OTAs driving a broad range of load capacitor

Advanced multistage amplifiers suffer from load-dependent stability issues, which limit the load capacitor range they can drive. In this work, the concept of global impedance attenuation (GIA) network is introduced to improve an amplifier's stability in the presence of significant load capacitor variations. Composed of multiple parallel resistor-capacitor (RC) branches, the equivalent high-frequency output impedance of gain stages is shaped by the GIA network such that a desired frequency spectrum is obtained over a wide range of load capacitor. The parasitic poles at the output of the gain stages are nullified by the proposed network, thereby simplifying the amplifier's transfer function and reducing the minimum load capacitor it can drive. The idea is applied to design a three-stage operational transconductance amplifier (OTA) with cascode global impedance attenuation (CGIA). Small-signal analysis shows that the OTA is stable regardless of the load capacitor, and it can drive very small to ultra-large load capacitors. This feature is verified by the post-layout simulations of a CGIA amplifier in 0.18-μm complementary metal-oxide semiconductor (CMOS) process. The core occupies a die area of 0.0053 mm² while consuming a static current of 10.97 μA from 1.8-V voltage supply. The unity-feedback configuration is unconditionally stable for any load capacitor higher than 10 pF. To the best of our knowledge, this corresponds to the widest range of load capacitance reported for prior-art three-stage amplifiers.