Study on morphology of ternary polymer blends. I. Effects of melt viscosity and interfacial interaction

The morphology of some ternary blends was investigated. In all of the blends polypropylene, as the major phase, was blended with two different minor phases, ethylene–propylene–diene terpolymer (EPDM) or ethylene–propylene–rubber (EPR) as the first minor phase and high‐density polyethylene (HDPE) or polystyrene (PS) as the second minor phase. All the blends were investigated in a constant composition of 70/15/15 wt %. Theoretical models predict that the dispersed phase of a multiphase polymer blend will either form an encapsulation‐type phase morphology or phases will remain separately dispersed, depending on which morphology has the lower free energy or positive spreading coefficient. Interfacial interaction between phases was found to play a significant role in determining the type of morphology of these blend systems. A core–shell‐type morphology for HDPE encapsulated by rubber was obtained for PP/rubber/PE ternary blends, whereas PP/rubber/PS blends showed a separately dispersed type of morphology. These results were found to be in good agreement with the theoretical predictions. Steady‐state torque for each component was used to study the effect of melt viscosity ratio on the morphology of the blends. It was found that the torque ratios affect only the size of the dispersed phases and have no appreciable influence on the type of morphology. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1129–1137, 2001     

Effect of ultrasound on extrusion of PP/EPDM blends: Structure and mechanical properties

The effects of ultrasonic irradiation on the mechanical properties, morphology, and crystal structure of polypropylene (PP)/ethylene‐propylene‐diene terpolymer (EPDM) blends were examined. Results show that appropriate irradiation intensity can noticeably increase the toughness of the PP/EPDM blends without reducing rigidity. Scanning electron microscopic (SEM) observation shows that with ultrasonic irradiation, the morphology of a well‐dispersed EPDM phase is formed in the PP/EPDM blend. The glass transition temperatures of PP and EPDM phase approach each other as a result of ultrasonic irradiation. Differential Scanning Calorimetric (DSC) analysis indicates that the crystallinities of the PP and EPDM phases increase with ultrasonic irradiation, and β crystals of PP form in the PP/EPDM blend with ultrasonic irradiation, which is proven by wide angle X‐ray diffraction (WAXD) analysis. Polym. Eng. Sci. 44:1509–1513, 2004. © 2004 Society of Plastics Engineers.     

Morphology prediction and the effect of core‐shell structure on the rheological behavior of PP/EPDM/HDPE ternary blends

In this work, the morphologies of polypropylene (PP)/ethylene‐propylene‐diene (EPDM) rubber/high density polyethylene (HDPE) 70/20/10 blends were studied and compared with the predictions of the spreading coefficient and minimum free energy models. The interfacial tension of PP/HDPE, PP/EPDM, and HDPE/EPDM blends were obtained by fitting the experimental dynamic storage modulus data to Palierne's theory. The prediction results showed core‐shell morphology (core of HDPE and shell of EPDM) in PP matrix. The PP/EPDM/HDPE blends were respectively prepared by direct extrusion and lateral injection method. Core‐shell morphology (core of HDPE and shell of EPDM) could be obtained with direct extrusion corresponding to the predicted morphology. The morphology of PP/EPDM/HDPE blends could be effectively controlled by lateral injection method. For PP/EPDM/HDPE blend prepared by lateral injection method, HDPE and EPDM phase were dispersed independently in PP matrix. It was found that the different morphology of PP/EPDM/HDPE blends prepared by two methods showed different rheological behavior. When the core‐shell morphology (core of HDPE and shell of EPDM) appeared, the EPDM shell could confine the deformation of HDPE core significantly, so the interfacial energy contribution of dispersed phase on the storage modulus of blends would be weaken in the low frequency region. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Effect of ultrasound on extrusion of polypropylene/ethylene–propylene–diene terpolymer blend: Processing and mechanical properties

The effects of ultrasonic irradiation on extrusion processing and mechanical properties of polypropylene (PP)/ethylene–propylene–diene terpolymer (EPDM) blends are examined. Results show that appropriate irradiation intensity can prominently decrease die pressure and apparent viscosity of the melt, increase output, as well as increase toughness of PP/EPDM blends without harming rigidity. In case the blends are extruded with ultrasonic irradiation twice, the impact strength of the blend rises sharply at 50–100 W ultrasonic intensity, and amounts to more than 900 J/m, 1.5 times as high as that of blend without ultrasonic irradiation. Scanning electron microscopy observation shows that with ultrasonic irradiation, morphology of uniform dispersed EPDM phase and good adhesion between EPDM and PP matrix was formed in PP/EPDM blend. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3519–3525, 2003     

Miscibility of blends of ethylene‐propylene‐diene terpolymer and polypropylene

The miscibility of polymers is not only an important basis for selecting a proper blending method, but it is also one of the key factors in determining the morphology and properties of the blends. The miscibility between ethylene‐propylene‐diene terpolymer (EPDM) and polypropylene (PP) was explored by means of dynamic mechanical thermal analysis, transmission electron microscopy (TEM), and differential scanning calorimetry (DSC). The results showed that a decrease in the PP content and an increase of the crosslinking density of EPDM in the EPDM/PP blends caused the glass‐transition temperature peaks of EPDM to shift from a lower temperature to higher one, yet there was almost no variance in the glass‐transition temperature peaks of PP and the degree of crystallinity of PP decreased. It was observed that the blends prepared with different mixing equipment, such as a single‐screw extruder and an open mill, had different mechanical properties and blends prepared with the former had better mechanical properties than those prepared with the latter. The TEM micrographs revealed that the blends were composed of two phases: a bright, light PP phase and a dark EPDM phase. As the crosslinking degree of EPDM increased, the interface between the phases of EPDM and PP was less defined and the EPDM gradually dispersed in the PP phase became a continuous phase. The results indicated that EPDM and PP were both partially miscible. The mechanical properties of the blends had a lot to do with the blend morphology and the miscibility between the blend components. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 315–322, 2002     

动态硫化对三元乙丙橡胶/聚丙烯共混体系等温结晶行为和形态结构的影响

研究了三元乙丙橡胶/聚丙烯(EPDM/PP)共混物和动态硫化EPDM/PP热塑性弹性体(TPV)的等温结晶行为及形态结构,并用Avrami方程对其进行等温结晶动力学分析。结果表明,EPDM/PP共混物和EPDM/PP TPV的等温结晶行为符合Avrami方程,在相同的结晶温度下,TPV比共混物的Avrami指数小,半结晶时间短,结晶速率常数大;EPDM/PP共混物为双连续相结构,而EPDM/PP TPV是以硫化的细小橡胶颗粒为分散相、PP为连续相的"海-岛"结构,橡胶颗粒尺寸约为0.5μm。     

Recycling of EPDM waste. II. Replacement of virgin rubber by ground EPDM vulcanizate in EPDM/PP thermoplastic elastomeric composition

Virgin ethylene propylene diene monomer (EPDM) rubber in a thermoplastic elastomeric blend of polypropylene (PP) and EPDM rubber was substituted by ground EPDM vulcanizate of known composition, after which the mechanical properties of the raw EPDM/waste EPDM/PP blends were determined. The ratio of the rubber content in the waste EPDM (r‐W‐EPDM) to the raw EPDM (R‐EPDM) in the blends was varied from 0 : 100 to 45 : 55. Attempts to replace higher amounts (>45%) of R‐EPDM by W‐EPDM failed because of processing difficulty. Although a drop in mechanical properties of the blends was observed at lower loadings of W‐EPDM, the properties showed improvement at intermediate W‐EPDM loadings. The R‐EPDM/W–EPDM/PP blends were found to be reprocessable. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3304–3312, 2001     

Response Surface Analysis of PS/EPDM/PA6 Ternary Blends: Effect of Mixing Sequence,Composition, and Viscosity Ratio on the Mechanical Properties

In this work, effect of three factors on the phase morphology and mechanical properties of ternary blends based on polystyrene (PS)/ethylene‐propylene‐diene terpolymer (EPDM)/polyamide6 (PA6) was investigated by response surface methodology (RSM). Results indicated that among the studied factors (i.e., mixing sequence, composition, and viscosity ratio of the minor phases), the first two have the greatest effect on the impact strength (75.6%) and tensile properties (tensile modulus (84.9%) and yield stress (88.9%); while EPDM/PA6 viscosity ratio has the least effect (≤ 2.1%) on the final mechanical properties. These achievements are, in fact, arising from the considerable changes in the phase morphology and the contribution share predicted by experimental design outputs. However, mixing sequences just affected on the size of dispersed particles, but samples with different compositions presented different morphology types. According to the mechanical characterization of PS/EPDM/PA6 blends, the maximum impact strength and tensile properties were not obtained simultaneously. Optimal levels of input factors, aimed to balance impact strength and tensile properties, are M1 simultaneous mixing sequence, C1 composition (70/10/20), and V1 viscosity ratio (PA6 with low viscosity). J. VINYL ADDIT. TECHNOL., 26:282–290, 2020. © 2019 Society of Plastics Engineers     

Processing of polyolefin blends

The morphology of binary and ternary polyolefin blends of polypropylene (PP), ethylene-propylene-diene terpolymer (EPDM) and polyethylene (PE) following processing by injection and compression molding has been examined by optical and scanning electron microscopy. Internal surfaces were generated by low temperature fracture and etching with cyclohexane. In binary blends, droplets of EPDM are elongated in the flow direction within 400μm of the mold surface in injection molding, yielding a skin region which is distinct from an isotropic core containing spherical EPDM inclusions. Spherical droplets of EPDM or PE in binary blends with PP increase in size with increasing compression molding time. In ternary blends, spherical inclusions containing both EPDM and PE are dispersed in PP. With increasing compression molding time, EPDM separates from PE and concentrates at the outer edges of the PE inclusion, effectively isolating PE from the PP matrix.     

Dynamic mechanical properties of polypropylene‐g‐maleic anhydride and ethylene–propylene–diene terpolymer blends: Effect of blend preparation methods

In this work, we attempted two different ways of processing to improve interfacial adhesion of polypropylene (PP) and ethylene–propylene–diene terpolymer (EPDM) by introducing maleic anhydride (MAH); In one way, the in situ grafting and dynamic vulcanization (ISGV) were performed simultaneously from PP and EPDM with MAH in the presence of dicumyl peroxide (DCP) in an intensive mixer. In another way, PP was first grafted with MAH and then the PP‐g‐MAH was blended with EPDM in the intensive mixer in the presence of DCP by the dynamic vulcanization (DV). It was found that the glass transition temperatures (T_gs) of both PP and EPDM phases were shifted to higher temperature as the EPDM content increased for the blends prepared by both IGSV and DV methods, mainly due to the crosslinking of EPDM. The higher T_gs and larger storage moduli were observed for the blends prepared by the ISGV method than those prepared by the DV method, while the morphology showed that the size reduction of dispersed particles in latter blends was larger than that of the former blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2777–2784, 2000     

Effects of blend composition and dynamic vulcanization on the morphology and dynamic viscoelastic properties of PP/EPDM blends

The morphology and dynamic viscoelastic properties of isotactic polypropylene (PP) blended with oil-free/oil-extended ethylene–propylene–diene (EPDM) rubbers were studied. Unvulcanized and dynamically vulcanized blends with the compositions PP/EPDM = 50/50 and = 30/70 were investigated. The morphology was observed by phase contrasted atomic force microscopy. The dynamic viscoelastic properties were determined with a rheometer of plate–plate configuration. It was shown that the rheological behavior was strongly affected by both the composition and the morphology of the blends. Significant improvement in the flowability of the dynamically vulcanized blends was observed when oil-extended EPDM was used instead of the oil-free version. It was demonstrated that the rheological properties are mostly controlled by the elastomer phase at low frequencies, while in the high-frequency range the influence of PP becomes dominant. The peculiarities in the rheological behavior of the thermoplastic elastomers (uncured blends, TPE) and thermoplastic dynamic vulcanizates (TPV, dynamically cured blends) containing oil-extended EPDMs were traced to a limited compatibility between the PP and EPDM components in the melt. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synergetic toughness and morphology of poly(propylene)/nylon 11/maleated ethylene‐propylene diene copolymer blends

Polypropylene (PP)/nylon 11/maleated ethylene‐propylene‐diene rubber (EPDM‐g‐MAH) ternary polymer blends were prepared via melt blending in a corotating twin‐screw extruder. The effect of nylon 11 and EPDM‐g‐MAH on the phase morphology and mechanical properties was investigated. Scanning electron microscopy observation revealed that there was apparent phase separation for PP/EPDM‐g‐MAH binary blends at the level of 10 wt % maleated elastomer. For the PP/nylon 11/EPDM‐g‐MAH ternary blends, the dispersed phase morphology of the maleated elastomer was hardly affected by the addition of nylon 11, whereas the reduced dispersed phase domains of nylon 11 were observed with the increasing maleated elastomer loading. Furthermore, a core‐shell structure, in which nylon 11 as a rigid core was surrounded by a soft EPDM‐g‐MAH shell, was formed in the case of 10 wt % nylon 11 and higher EPDM‐g‐MAH concentration. In general, the results of mechanical property measurement showed that the ternary blends exhibited inferior tensile strength in comparison with the PP matrix, but superior toughness. Especially low‐temperature impact strength was obtained. The toughening mechanism was discussed with reference to the phase morphology. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of EPDM‐g‐MAH on the morphology and properties of PA6/EPDM/HDPE ternary blends

The formation of core‐shell morphology within the dispersed phase was studied for composite droplet polymer‐blend systems comprising a polyamide‐6 matrix, ethylene‐propylene‐diene terpolymer (EPDM) shell and high density polyethylene (HDPE) core. In this article, the effect of EPDM with different molecular weights on the morphology and properties of the blends were studied. To improve the compatibility of the ternary blends, EPDM was modified by grafting with maleic anhydride (EPDM‐g‐MAH). It was found that core‐shell morphology with EPDM‐g‐MAH as shell and HDPE as core and separated dispersion morphology of EPDM‐g‐MAH and HDPE phase were obtained separately in PA6 matrix with different molecular weights of EPDM‐g‐MAH in the blends. DSC measurement indicated that there may be some co‐crystals in the blends due to the formation of core‐shell structure. Mechanical tests showed that PA6/EPDM‐g‐MAH/HDPE ternary blends with the core‐shell morphology exhibited a remarkable rise in the elongation at break. With more perfect core‐shell composite droplets and co‐crystals, the impact strength of the ternary blends could be greatly increased to 51.38 kJ m^?2, almost 10 times higher than that of pure PA6 (5.50 kJ m^?2). POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Morphologies of polyethylene–ethylene/propylene/diene monomer particles in polypropylene‐rich polyolefin blends: Flake structure

Morphologies of polyethylene–ethylene/propylene/diene monomer (PE/EPDM) particles in 93/7 polypropylene (PP)/PE blends were investigated. SEM micrographs of KMnO₄‐etched cut surfaces and fracture surfaces of the blends revealed the existence of the “flake” structure. In the particles, crystalline PE formations with flake shape, which remain after etching, are called flakes. In addition to the PE‐crystalline flakes, amorphous PE, located between PE crystalline lamellae and EPDM rubber, complement the flake structure. The flakes are usually linked with the PP matrix, as seen in the heptane‐treated cut surfaces. These links, although observed with compatibilized samples, originate from the crystalline nature of PE particles, if no compatibilizer is added. Separately, the morphology of Royalene (consisting of high‐density PE and EPDM rubber, used as a PP/PE compatibilizer) was investigated by low‐voltage scanning TEM. The interaction of the components in the PE/EPDM blends can explain the formation of the flakes and toughening of the PP/PE blends. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3087–3092, 2003     

Carbon black‐reinforced dynamically cured EPDM/PP thermoplastic elastomers. I. Morphology,rheology, and dynamic mechanical properties

The structure development, rheological behavior, and viscoelastic properties of carbon black‐filled dynamically vulcanized thermoplastic elastomers based on the ethylene–propylene–diene terpolymer (EPDM) and polypropylene (PP) with the ratio range of 50/50 to 80/20 were studied and compared with similar but unfilled samples. Two‐phase morphology was observed at all ratios for the dynamically cured samples in which rubber particles are dispersed in the thermoplastic matrix. Carbon black distribution in each phase and damping behavior was found to be dependent upon the mixing condition and route of carbon black feeding. However, carbon black tends to stay mainly in the rubber phase, which leads to increase in the viscosity difference and, therefore, increase in the rubber particle size. Tensile strength and rupture energy increased with carbon black loading. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1127–1137, 2000     

Application of phase dispersion–crosslinking synergism on recycling commingled plastic wastes

A tetra‐component blend, consisting of low‐density polyethylene (LDPE), polyvinyl chloride (PVC), polypropylene (PP), and polystyrene (PS), was studied as a model system of commingled plastic wastes (LDPE/PVC/PP/PS, mass ratio: 70/10/10/10). Effects of chlorinated polyethylene (CPE), ethylene–propylene–diene monomer (EPDM), styrene–butadiene–styrene (SBS), and their mixture (CPE/EPDM/SBS, mass ratio: 2/2/2) on the mechanical properties and morphology of the system were investigated. With addition of several elastomers and their mixture, the tensile strength of the blends decreased slightly, although both the elongation at break and the impact strength increased. Among these elastomers, EPDM exhibited the most significant impact modification effect for the tetra‐component blends. SBS and the mixture have a good phase‐dispersion effect for the tetra‐component blend. By adding a crosslinking agent [dicumyl peroxide (DCP)], the mechanical properties of the tetra‐component blends also increased. When either SBS or the mixture was added to the blend together with DCP, the probability that the crosslinking agent (DCP) would be at the interface improved because of the phase‐dispersion effect of SBS. Therefore, more co‐crosslinked products will form between LDPE and other components. Accordingly, remarkable improvement of the interfacial adhesion and hence the mechanical properties of the tetra‐component blends occurred. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2947–2952, 2001     

乙丙橡胶增韧聚丙烯共混物中橡胶相形态

通过电子扫描电镜(SEM),研究了乙丙橡胶增韧聚丙烯共混物中作为分散相的橡胶粒子的形态。结果表明,在交联剂等助剂的作用下进行过动态硫化的共混物中橡胶相的粒子形状、粒径、粒径分布以及橡胶粒子与连续相聚丙烯所形成的界面形态与单纯的橡塑共混物和PP/EPDM反应器共混物相比有着截然不同的区别。正是由于这些区别,提高了经过动态硫化的共混物的冲击性能。     

Influences of component ratio of minor phases and charge sequence on the morphology and mechanical properties of PP/PS/PA6 ternary blends

In this study, influences of both component ratio of minor phases and charge sequence on the morphology and mechanical performance in typical ternary blends, polypropylene (PP)/polystyrene (PS)/polyamide-6 (PA6), have been studied. Reactive compatibilization of the blends has been carried out using multi-monomer melt grafted PP with anhydride groups and styrene segments. For uncompatibilized blends, scanning electron microscope (SEM) and selective solvent extraction showed that the blends presented a core–shell morphology with PS as shell and PA6 as core in the PP matrix, in spite of the component ratio and charge sequence. The shell thickened and droplet size decreased with increasing the PS/PA6 component ratio. While for compatibilized blends, the addition of compatibilizers resulted in a significant reduction of the dispersed droplet size and the phase structure of the dispersed phases was greatly dependent on the charge sequence. When the blending of PA6, g-PP, and PP are preceded, the encapsulation structure reversed into the structure of PS phase encapsulated by PA6 phase, which led to better tensile and flexural strength of the blends.     

Tensile properties and morphology of the dynamically cured EPDM and PP/HDPE ternary blends

The tensile properties and morphology of the polyolefin ternary blends of ethylenepropylene–diene terpolymer (EPDM), polypropylene and high density polyethylene were studied. Blends were prepared in a laboratory internal mixer where EPDM was cured in the presence of PP and HDPE under shear with dicumyl peroxide (DCP). For comparison, blends were also prepared from EPDM which was dynamically cured alone and blended with PP and HDPE later (cure–blend). The effect of DCP concentration, intensity of the shear mixing, and rubber/plastics composition was studied. The tensile strength and modulus increased with increasing DCP concentration in the blends of EPDM-rich compositions but decreased with increasing DCP concentration in blends of PP-rich compositions. In the morphological analysis by scanning electron microscopy (SEM), the small amount of EPDM acted as a compatibilizer to HDPE and PP. It was also revealed that the dynamic curing process could reduce the domain size of the crosslinked EPDM phase. When the EPDM forms the matrix, the phase separation effect becomes dominant between the EPDM matrix and PP or HDPE domain due to the crosslinking in the matrix.     

Dynamic vulcanization of polyethylene‐based thermoplastic elastomer blends

In this investigation, the effects of blending with ethylene–propylene–diene terpolymer and subsequent dynamic curing with sulfur on the macromolecular structure and properties of pure low‐density polyethylene and high‐density polyethylene were studied. The crosslinking efficiency of polyethylene‐based ethylene–propylene–diene terpolymer blends upon dynamic curing was assessed with torque and gel content measurements. The curing of dispersed ethylene–propylene–diene terpolymer in a polyethylene matrix improved both the mechanical and thermomechanical properties as a result of the formation of a crosslink structure in the rubber phase. In view of the electrical applications of this cured blend material, the volume resistivity was measured. The thermal stability of vulcanized polyethylene/ethylene–propylene–diene terpolymer blends was found to be superior to that of unvulcanized blends. In scanning electron microscopy analysis, good interface bonding between the polyethylene matrix and dispersed ethylene–propylene–diene terpolymer was observed for the cured blends. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010