气体分布方式对带列管内构件的鼓泡塔流动规律的影响

在带列管内构件的鼓泡塔内测量了4种不同布气方式下的气含率和液速径向分布,并与无列管内构件的空塔中的分布进行了比较。结果表明：中心布气条件下气含率与液速的径向分布比空塔更为陡峭;环隙及近壁布气时呈现出环隙高、两边低的马鞍形分布;均匀布气时径向分布较空塔更为平坦。空塔内气体分布器的影响是局部性的,充分发展段在塔内占主要部分;而在列管塔中气体分布器的影响是全局性的,气含率与液速的初始分布决定着其全塔分布。在带列管的大型鼓泡塔中难以观察到充分发展段的存在,因此,气体分布器的设计具有比空塔更为重要的意义     

A structured catalytic bubble column reactor: hydrodynamics and mixing studies

This paper reports the results of a comprehensive experimental study of the hydrodynamics and mixing in two bubble column reactors of 0.1 and 0.24 m in diameter with KATAPAK-S^® as packing material. Total gas hold up and axial dispersion coefficients were measured in the structured bubble columns and the values were compared with experimental results obtained in the same work with empty bubble columns. The results reveal that the gas hold up in structured bubble columns is practically the same as in empty bubble columns when compared at the same superficial gas velocity based on open area available for gas–liquid dispersion. The presence of the structured elements in the bubble column reactor reduces the liquid phase backmixing by one order of magnitude.     

Hydrodynamics of an annulus airlift reactor

The hydrodynamics of an annulus airlift reactor (AALR) was studied and compared with that of a slurry bubble column reactor (SBCR) with silica sands of 75-125 μm in size as solids, city tapping water as liquid phase, and air as gas phase in the present investigation. The effects of superficial gas velocity and solids concentration on gas holdup and solids distributions were investigated. The results showed that the local average gas holdup decreased along the column height, and the average gas holdup decreased with the increasing solids concentration, but this tendency became less at higher solids concentrations. It was found that the effect of superficial gas velocity on axial solids distribution was negligible over the gas velocity range investigated, as long as the solids in the column could be suspended. Increasing solids concentration led to flatter axial solids holdup profiles. The axial distributions of solids concentration and gas holdup in the AALR were much more uniform than those in the SBCR, and slurry circulation in the AALR damped the effects of increasing solids concentration on the hydrodynamics. These advantages of an AALR over a SBCR are especially important for some catalytic reaction processes in three-phase systems such as Fischer-Tropsch synthesis and methanol synthesis.     

Experimental and numerical investigations of scale-up effects on the hydrodynamics of slurry bubble columns

Experiments and simulations were conducted for bubble columns with diameter of 0.2 m(180 mm i.d.), 0.5 m(476 mm i.d.) and 0.8 m(760 mm i.d.) at high superficial gas velocities(0.12–0.62 m·s-1) and high solid concentrations(0–30 vol%). Radial profiles of time-averaged gas holdup, axial liquid velocity, and turbulent kinetic energy were measured by using in-house developed conductivity probes and Pavlov tubes. Effects of column diameter, superficial gas velocity, and solid concentration were investigated in a wide range of operating conditions. Experimental results indicated that the average gas holdup remarkably increases with superficial gas velocity, and the radial profiles of investigated flow properties become steeper at high superficial gas velocities. The axial liquid velocities significantly increase with the growth of the column size, whereas the gas holdup was slightly affected. The presence of solid in bubble columns would inhibit the breakage of bubbles, which results in an increase in bubble rise velocity and a decrease in gas holdup, but time-averaged axial liquid velocities remain almost the same as that of the hollow column. Furthermore, a 2-D axisymmetric k–ε model was used to simulate heterogeneous bubbly flow using commercial code FLUENT 6.2. The lateral lift force and the turbulent diffusion force were introduced for the determination of gas holdup profiles and the effects of solid concentration were considered as the variation of average bubble diameter in the model. Results predicted by the CFD simulation showed good agreement with experimental data.     

Local hydrodynamic properties of gas phase in an internal-loop airlift reactor

The local hydrodynamic properties of the gas phase in an internal-loop airlift reactor were investigated in this study. The hydrodynamic properties including gas holdup, bubble velocity and bubble chord length were measured by dual electrical resistivity probes. The chord length distribution was then transformed to the bubble size distribution by modeling the bubbles as ellipsoids. It was found that the gas holdup increased with decreasing bubble velocity. In addition, most bubbles tended to rise along the riser central axis. Thus, the gas holdup in the axis was higher. The bubble size, bubble velocity and gas holdup were relatively constant in the axial direction of the riser except in the zones near the gas sparger and the gas–liquid separator. The bubble velocity became slower when the bubbles approached the gas–liquid separator. Moreover, the bubble size and bubble velocity for the three-phase system were relatively insensitive to the radial direction compared to those for the two-phase system. It was also found in this study that the bubble rise velocity and bubble size for the three-phase system were lower than that for the two-phase system. However, the gas holdup for the three-phase system were higher than that for the two-phase system due to bubble breakage caused by the solid particles.     

基于气泡群相间作用力模型的加压鼓泡塔流体力学模拟

目前,多数文献报道了冷态加压湍动鼓泡塔内流动特征,并且通过实验数据回归相关经验关联式。然而,此类关联式适用范围有限,难以直接外推到工业鼓泡塔反应器条件。因此,在FLUENT平台上建立了基于气泡群相间作用力的、动态二维加压鼓泡塔计算流体力学模型。通过数值模拟考察了操作压力为0.5~2.0 MPa,表观气速为0.20~0.31 m·s^-1,内径0.3 m鼓泡塔内流场特性参数分布,并且与冷态实验数据进行比较。结果表明,采用修正后的气泡群曳力模型、径向力平衡模型以及壁面润滑力模型描述气泡群相间作用力,能够较为准确地反映平均气含率和气含率径向分布随操作压力和表观气速变化的规律。     

鼓泡床反应器内流动与传质行为的研究进展

总结了有关浆态鼓泡床反应器内流动、混合用气液传质特性的研究成果,详细地介绍了鼓泡床反应器内气含率、液速、液体轴向扩散系数、传质系数的测量方法,阐述了鼓泡床反应器性能的主要影响因素,如系统压力、温度、气体表观气速、液体性质及固含率等对流动、液相混合和传质特性的影响,并对鼓泡床反应器的应用前景进行了详述.     

Hydrodynamics of a Tapered Bubble Column

The hydrodynamic behavior of a single‐stage tapered bubble column using an air‐water two‐phase system has been studied. The experimental results indicate that the holdup increases with increasing superficial gas velocity and bubble slip velocity, while it remains constant with increasing superficial liquid velocity. The gas flow rate has a subtle effect on pressure drop owing to the dynamic pressure recovery stemming from the increase in flow area in the axial direction. The results further suggest that the tapered bubble column shows higher holdup with lower energy dissipation than the conventional bubble columns under similar hydrodynamic conditions. The experimental values of the holdup are in excellent agreement with the well‐known Akita and Yoshida correlation available in the existing literature. Also, the performance of the tapered system has been shown to be much better than that of conventional columns under similar conditions in water/alkaline scrubbing of fly ash and SO₂ either alone or in combination.     

Flow behavior of wakes in a three-phase slurry bubble column with viscous liquid medium

Flow behavior of wakes has been investigated in a three-phase slurry bubble column of 0.102 m ID and 1.5 m in height. The dependence of wake characteristics such as rising velocity, frequency, holdup and equivalent size on the operating variables was examined by employing an electric resistivity probe method. The gas velocity, liquid viscosity and solid content in the slurry phase were chosen as independent parameters. The rising velocity of wake region increased with an increase in the gas velocity (4.0–12.0 cm/s), liquid viscosity (1.0–50.0 mPa·s) or solid content (0–25 wt%) in the slurry phase. The frequency and holdup of wake phase increased with increasing gas velocity, but decreased with increasing liquid viscosity or solid content in the slurry phase. The equivalent size of wake phase increased with increasing gas velocity, liquid viscosity or solid content in the slurry phase. The wake properties and holdup were well correlated with operation variables within these experimental conditions.     

MASS TRANSFER AND PHASE HOLDUP CHARACTERISTICS IN THREE-PHASE FLUIDIZED BEDS

The effects of liquid surface tension (42.6 ∼ 72,4 mN/m) and viscosity (1 ∼214mPa • sⁿ), liquid (0.01 ∼0.12m/s) and gas (0.01 ∼0.20m/s) velocities and particle sizes (1 — 8 mm) on phase holdup and mass transfer coefficient ( k_La) have been determined in a 0.142 m-I.D. × 2.0 m-high Plexiglas column. The gas phase holdup increases with liquid velocity, and the rate of increase in gas phase holdup sharply increases with gas velocity in the bed of surfactant solutions. In the beds of 1.0 and 1.7 mm glass beads, the bed contraction occurs whereas in the beds of 2.3 mm glass beads the bed contraction does not occur with an aqueous soltuion of ethanol (σ = 50.4 mN/m). The value of k_La increases with decreasing surface tension (σ ) but it decreases exponentially with increasing liquid viscosity in continuous bubble columns and three-phase fluidized beds. In three-phase fluidized beds with surfactant solutions, k_La increases with gas and liquid velocities and particle size. In three-phase fluidized beds of viscous or surfactant soltuions, k_L,a can be estimated in terms of the energy dissipation rate based on the isotropic turbulence theory and a flow regime map is proposed based on the drift flux theory.     

Hydrodynamics of air–kerosene bubble column under elevated pressure in homogeneous flow regime

A multiphase computational fluid dynamics(CFD) model coupled with the population balance equation(PBE) was developed in a homogeneous air–kerosene bubble column under elevated pressure(P). The specific pressure drop(DP/L), gas holdup(a_G), and Sauter mean diameter(d_(32)) were experimentally measured in the bubble column with 1.8 m height and 0.1 m inner diameter, which was operated at a superficial gas velocity of 12.3 mm·s~(-1), and P = 1–35 bar(1 bar = 10~5 Pa). A modified drag coefficient model was proposed to consider the effect of bubble swarm and pressure on hydrodynamics of the bubble column.The Luo breakage model was modified to account for liquid density, viscosity, surface tension and gas density. The DP/L, a_G, and d_(32) obtained from the CFD model were compared with experimental data,and the gas density-dependent parameters of the CFD model were identified. With increasing P from 1 to 35 bar, the aGvaried from 5.4% to 7.2% and the d_(32) decreased from 2.3 to 1.5 mm. The CFD-PBE model is applicable to predict hydrodynamics of pressurized bubble columns for gas–organic liquid in the homogeneous regime.     

Bubble and gas holdup characteristics in a bubble column of CMC solution

The local bubble behavior such as holdup, bubble frequency, bubble size and rising velocity in a bubble column of CMC solution was measured using the eleclroresislivity probe technique, and the effects of gas velocity and CMC concentration on the behavior were investigated. Also, the total gas holdup was measured from the liquid level in the column, and its relation with gas velocity and CMC concentration was studied. Two correlations of mean bubble size and total gas holdup with dimensionless groups, composed of gas velocity and physical properties of gas and liquid, were obtained from the experimental results.     

基于EMMS方法的鼓泡塔反应器CFD及群平衡模拟

能量最小多尺度（energy-minimization multi-scale,EMMS）方法已经被应用于气液体系中群平衡（population balance model,PBM）模型的改进。EMMS模型可计算气泡破碎聚并过程的能量,进而获得聚并速率的修正因子。应用这一模型对高气速鼓泡塔进行了模拟计算,并进一步对比了均一尺径模型、CFD-PBM模型以及CFD-PBM-EMMS模型的模拟结果与实验数据。结果表明,在高表观气速条件下,基于EMMS方法的群平衡模型可以更加准确地预测鼓泡塔中不同高度的气泡尺径分布和轴向液速,同时提高了对整体气含率和局部气含率的模拟准确性。在表观气速为0.16 m·s^-1和0.25 m·s^-1时,CFD-PBM-EMMS模型对气泡尺径分布的预测精度更高,同时整体气含率模拟的相对误差下降为5%和15%,局部气含率模拟平均相对误差下降为8%和17%。     

鼓泡塔中气泡尺寸分布和局部气含率研究

在内径为0.38 m的鼓泡塔中采用双电导探针法对不同通气速率下的气泡尺寸分布和局部气含率进行了实验研究,分析了气泡尺寸的概率密度分布。结果表明:气泡尺寸随轴向高度的增加而增大,随径向距离增加而减小;鼓泡塔中气液流动可分为过渡流域和充分发展流域,在过渡流域气含率随轴向高度增加而增大,在充分发展流域气含率趋于均值,径向局部气含率分布呈抛物线型下降。高气速下气泡尺寸概率密度分布比低气速下宽,且随轴向高度的增加分布变宽。     

Porous mullite–ZrO2 composites from reaction sintering of zircon and aluminum

Mullite–zirconia porous bodies were prepared by reaction sintering of zircon and alumina derived from oxidation reaction of Al at sintering temperatures between 1200 and 1600 °C. The results show that the incorporation of TiO₂ improves the oxidation reaction of Al, dissociation of zircon subsequently formation of mullite and zirconia. Composites containing TiO₂ obtain a high tetragonal concentration at 1500 °C, which reduces by increasing sintering temperature to 1600 °C. No tetragonal zirconia phase was detected at 1500 °C in TiO₂-free composites while tetragonal concentration was increased over this temperature. The major oxidation reaction of Al proceeds with a liquid–gas mechanism that is suitable for producing low dense ceramics. In spite of the higher porosity of the composites containing TiO₂, they possess almost the same flexural strength values as obtained from the TiO₂-free composites.     

网格和数值格式对TBPBM-CFD模型模拟鼓泡塔的影响

基于气泡动力学属性的现有认识,把气泡分成大、小气泡,首次建立了完整的双气泡相-群平衡模型(TBPBM)以预测气泡尺寸.通过编写用户自定义程序实现了TBPBM模型、Luo破碎模型以及Prince 聚并模型,并耦合TBPBM与CFD双流体模型对直径440 mm鼓泡塔进行数值模拟,详细考察了网格与数值格式对TBPBM-CFD模型模拟结果的影响.结果表明,网格与数值格式对各物理变量的模拟结果影响非常大,特别是网格和体积分数方程对流项离散格式的影响最为显著.随着计算精度的提高,湍流耗散率和整体气含率分布梯度增大,气泡平均直径减少,大气泡所占气相比率降低,液相速度及气含率径向分布与实验值更趋吻合.     

Structured multiphase reactors based on fibrous catalysts: nitrite hydrogenation as a case study

A new reactor concept designed as a bubble column staged with fibrous catalytic layers is tested on pilot-scale for the reduction of nitrite to nitrogen by hydrogen. Carbon dioxide is used to neutralize the hydroxide ions produced during hydrogenation of nitrite. The effective reaction rate was found to depend on the superficial gas velocity u_g0. The fibrous catalysts demonstrated a high selectivity towards nitrogen. The influence of the mass transport on the effective kinetics is discussed and the volumetric liquid–solid mass transfer coefficient k_Sa_S is estimated as a function of the superficial gas velocity u_g0. The selectivity was found to be independent of the hydrodynamics.     

Axial dispersion in a rectangular bubble column

This paper presents the results of an experimental study on the gas holdup and the liquid phase axial dispersion coefficient in a narrow packed and unpacked rectangular bubble column. In both cases the gas and liquid flow rates were varied and the data were obtained by employing standard tracer technique. The gas holdup and the axial dispersion coefficient for both the packed and unpacked columns were found to be dependent on the gas and liquid flow rates. For given gas and liquid velocities and a given packing size in the case of the packed column, the rectangular column gave significantly higher dispersion coefficients than a cylindrical column of the equivalent cross sectional area. This result agrees very well with the one predicted by the velocity distribution model. The correlations for the Peclet number, the axial dispersion coefficient, and the fluid holdup for both the unpacked and packed bubble columns are presented.     

Behavior of gas bubbles in a concentric cylindrical airlift column

Using a light transmission optical probe, the effect of superficial gas velocity on bubble properties(bubble size, bubble rising velocity, bubble frequency and local gas holdup) at axial and radial positions was determined in the riser and the downcomer of a concentric cylindrical airlift reactor. The vertical bubble length, the bubble rising velocity and the bubble frequency at axis in the riser increased with increasing superficial gas velocity and the bed height. The radial distribution of the local gas holdup, vertical bubble length and bubble frequency in the riser and the downcomer were found to be non-uniform. The profiles of the local gas holdup, vertical bubble length and bubble rising velocity in the riser were shown as parabolic shapes. The local gas holdup, the vertical bubble length and the bubble frequency in the downcomer changed with superficial gas velocity and the distance from the top of the draft tube.     

HYDRODYNAMICS, MIXING AND MASS TRANSFER IN A LARGE DIAMETER JET BUBBLE COLUMN

Experimental measurements for the axial and radial variations in gas holdup, axial and radial dispersion coefficients, volumetric gas-liquid mass transfer coefficient and liquid phase circulation velocity in a cone of a large diameter (122 cm) jet bubble column are presented. Two diameters of the inlet nozzle, namely 10.16 cm and 15.24 cm, three superficial gas velocities (based on cylinder diameter), 3 cm/sec, 6 cm/sec and 8 cm/sec and two superficial liquid velocities, 0.3 cm/sec and 0.6 cm/sec, are examined. The experimental data are obtained for two different bed heights.

The experimental data showed significant axial and radial variations in the gas holdup. The volumetric average gas holdup was higher at higher gas velocity and larger nozzle diameter and somewhat higher at lower liquid velocity. The axial dispersion was high while the radial dispersion was low. The volumetric gas-liquid mass transfer coefficient was larger at higher gas velocity and larger nozzle diameter. The liquid recirculation begins only at the upper end of the cone. In general, experimental data indicate that a jet bubble column provides a high degree of mixing and transport rates.