The role of methyl methacrylate on branching and gel formation in the emulsion copolymerization of BA/MMA

The effect of the monomer ratio on the microstructure of BA/MMA emulsion copolymers was investigated. Monomer ratios spanned from pure BA used for adhesives to 50/50 wt/wt BA/MMA copolymers used for coatings. The gel content varied from 55% for pure BA to nil for the 50/50 copolymer. The branching level was reduced from 2.6% for pure BA to 0.3% for a 75/25 BA/MMA copolymer. The mechanisms responsible for the reduction of gel content can be found in the lower reactivity of the MMA terminated chains for hydrogen abstraction, the absence of abstractable hydrogens in the MMA units and the fact that MMA radicals terminate predominantly by disproportionation. The reduction of the level of branches is mainly due to the lower reactivity of MMA for intramolecular transfer and the lower instantaneous conversions that favored propagation over backbiting.     

Adsorption of IgG on spacer‐arm and L‐arginine ligand attached poly(GMA/MMA/EGDMA) beads

This work presents data on human immunoglobulin G (HIgG) adsorption onto L ‐arginine ligand attached poly(GMA/MMA/EGDMA)‐based affinity beads which were synthesized from methyl methacrylate (MMA) and glycidiyl methacrylate (GMA) in the presence of a crosslinker (i.e., ethylene glycol dimethacrylate; EGDMA) by suspension polymerization. The epoxy groups of the poly(GMA/MMA/EGDMA) beads were converted into amino groups after reaction with ammonia or 1,6‐diaminohexane (i.e., spacer‐arm). With L ‐arginine as a ligand, it was covalently immobilized on the aminated (poly(GMA/MMA/EGDMA)‐ AA) and/or the spacer‐arm attached (poly(GMA/MMA/EGDMA)‐SA) beads, using glutaric dialdehyde as a coupling agent. Both affinity poly(GMA/MMA/EGDMA)‐based beads were used in HIgG adsorption/desorption studies under defined pH, ionic strength, or temperature conditions in a batch reactor, using acid‐treated poly(GMA/MMA/EGDMA) beads as a control system. The poly(GMA/MMA/EGDMA)‐SA affinity beads resulted in an increase in the adsorption capacity to HIgG compared with the aminated counterpart (i.e., poly(GMA/MMA/EGDMA)‐AA). The maximum adsorption capacities of the poly(GMA/MMA/EGDMA)‐AA and poly(GMA/MMA/EGDMA)‐SA affinity beads were found to be 112.36 and 142 mg g^?1, and the affinity constants (K_d), evaluated by the Langmuir model, were 2.48 × 10^?7 and 6.98 × 10^?7M, respectively. Adsorption capacities of the poly(GMA/MMA/EGDMA)‐AA and poly(GMA/MMA/EGDMA)‐SA were decreased with HIgG by increasing the ionic strength adjusted with NaCl. Adsorption kinetic of HIgG onto both affinity adsorbents was analyzed with first‐ and second‐order kinetic equations. The first‐order equation fitted well with the experimental data. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 672–679, 2007     

Simultaneous interpenetrating networks of a polyurethane and poly(methyl methacrylate). II. Partitioning of MMA monomer in the last stages of polymerization

In a model polyurethane/poly(methyl methacrylate) (PU/PMMA) system, the partitioning of unreacted methyl methacrylate monomer (MMA) is studied in the late stages of its polymerization, simulated by incorporating controlled amounts of MMA in otherwise fully cured simultaneous interpenetrating networks (SIN) samples. Glass transitions temperatures (T_g) were determined using dynamic mechanical spectroscopy and differential scanning calorimetry as a function of MMA content of the SINs. The lowering of T_g in each phase due to the plasticization effect of MMA is used to calculate a plasticization coefficient for each phase, finally allowing calculation of the partition coefficient of MMA between the two phases. It is found that the MMA monomer distributes itself almost uniformly across the two phases of the current SIN system, leading to speculation as to the locus of late SIN polymerization. © 1995 John Wiley & Sons, Inc.     

Effect of methyl methacrylate on the properties of transparent flame retardant unsaturated phosphate ester copolymer

The effect of methyl methacrylate (MMA) on the properties of transparent flame retardant unsaturated phosphate ester copolymer (poly[UPE‐co‐MMA]) prepared by bulk polymerization technique was investigated. Fourier transform infrared spectra, gel fraction (G) test, and dynamic mechanical analysis revealed the structure and crosslinking density of poly(UPE‐co‐MMA) copolymers. The thermal degradation and flame retardancy of copolymers were indicated by thermogravimetric analysis, limiting oxygen index (LOI), and microscale combustion calorimeter (MCC) test. Besides, the mechanical properties and transparency were tested with testing machines and solid ultraviolet absorption spectra. As the MMA content increased to 50%, the copolymer contained 50 wt% MMA showed the maximal G (88.93%) and transmittance was up to 91.72%. From the poly(UPE‐co‐MMA) copolymers, the tensile strength increased from 14.62 to 26.95 MPa, assigned to the increase of crosslinking density of copolymers. The char yield of poly(UPE‐co‐MMA) was up to 21.18 wt%, which was a result of decomposition of phosphate groups, producing a phosphorus‐rich layer that increased the thermal stability of the residues. LOI and MCC results confirm that the introduction of MMA can retain the flame retardancy of copolymer remarkably. POLYM. ENG. SCI., 59:2103–2109, 2019. © 2019 Society of Plastics Engineers     

Irradiation grafting of methyl methacrylate monomer onto ultra‐high‐molecular‐weight polyethylene: An experimental design approach for improving adhesion to bone cement

The grafting of methyl methacrylate (MMA) onto ultra‐high‐molecular‐weight polyethylene (UHMWPE) and chromic acid etched UHMWPE was conducted with a preirradiation method in air in the presence of a Mohr salt and sulfuric acid. The grafted samples were characterized by Fourier transform infrared (FTIR) spectroscopy, a gravimetric method, differential scanning calorimetry, scanning electron microscopy (SEM), and interfacial bonding strength measurements. The FTIR results showed the presence of ether and carbonyl groups in the MMA‐grafted UHMWPE (MMA‐g‐UHMWPE) samples. The Taguchi experimental design method was used to find the best degree of grafting (DG) and bonding strength. The efficient levels for different variables were calculated with an analysis of variance of the results. SEM micrographs of MMA‐g‐UHMWPE samples showed that with increasing DG and chromic acid etching, the MMA‐g‐UHMWPE rich phase increased on the surface; this confirmed the high interfacial bonding strength of the grafted samples with bone cement. The grafting of the MMA units onto UHMWPE resulted in a lower crystallinity, and the crystallization process proceeded at a higher rate for the MMA‐g‐UHMWPE samples compared to the initial UHMWPE; this suggested that the MMA grafted units acted as nucleating agents for the crystallization of UHMWPE. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Study on the phase behavior of ethylene–vinyl acetate copolymer and poly(methyl methacrylate) blends by in situ polymerization

This study examines the phase behavior of ethylene–vinyl acetate copolymer (EVA) and poly(methyl methacrylate) (PMMA) blends during MMA polymerization. The ternary PMMA/MMA/EVA mixtures are considered to create a triangular phase diagram, which responds the phase changes during polymerization. The phase changes during MMA polymerization are also examined by optical microscope and photometer. Since the PMMA and EVA are well‐known immiscibles, the polymer solution undergoes phase separation at the initial stage of the MMA polymerization. Additionally, the phase inversion occurs as the conversion of MMA between 13.8 and 20.8%. On the other hand, the EVA‐graft‐PMMA, which can reduce the dispersed EVA particle size, is induced efficiently by taking tert‐butyl peroctoate (t‐BO) as initiator during MMA polymerization. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1001–1008, 2003     

Co-pyrolysis of polymethyl methacrylate with brown coal and effect on monomer production

Pyrolysis capillary gas chromatography has been applied to the study of the co-pyrolysis of polymethyl methacrylate (PMMA) with Slovakian brown coal with the aim of finding pyrolysis conditions yielding a maximum amount of methyl methacrylate (MMA). Effects of pyrolysis temperature and PMMA-coal weight ratios were investigated. Capillary gas chromatography coupled with mass spectrometric detector (cGC-MS) was used for MMA identification. The highest yield of MMA in the pyrolysate was obtained at 750 °C. The optimal PMMA-coal weight ratio for maximum MMA production lies in the interval 0.5 mg PMMA and 0.6-0.8 mg brown coal with an MMA yield of 64%. Coal addition to the sample affects species recombination in gaseous phase, augments MMA production at higher temperatures and eliminates degradation products of PMMA and coal pyrolysis. Different conversion diagrams are characteristic for thermal degradation of single PMMA and in the mixture with coal. Detailed mechanism of synergetic effects arisen during co-pyrolysis are not yet known. It was also found that lower pyrolysis temperatures are more suitable to study degradation mechanism and kinetics while higher temperatures are more applicable for identification purposes. MMA decomposes completely at 900 °C.     

Preparation of polymer‐supported polyethylene glycol and phase‐transfer catalytic activity in benzoate synthesis

The crosslinked polymeric microspheres (GMA/MMA) of glycyl methacrylate (GMA) and methyl methacrylate (MMA) were prepared by suspension polymerization. Polyethylene glycol (PEG) was grafted on GMA/MMA microsphers via the ring‐opening reaction of the epoxy groups on the surfaces of GMA/MMA microspheres, forming a polymer‐supported triphase catalyst, PEG‐GMA/MMA. The Phase‐transfer catalytic activity of PEG‐GMA/MMA microspheres was evaluated using the esterification reaction of n‐chlorobutane in organic phase and benzoic acid in water phase as a model system. The effects of various factors on the phase transfer catalysis reaction of liquid–solid–liquid were investigated. The experimental results show that the PEG‐GMA/MMA microspheres are an effective and stable triphase catalyst for the esterification reaction carried out between oil phase and water phase. The polarity of the organic solvent, the ratio of oil phase volume to water phase volume and the density of the grafted PEG on PEG‐GMA/MMA microspheres affect the reaction rate greatly. For this investigated system, the solvent with high polarity is appropriate, an adequate volume ratio of oil phase to water phase is 2:1, and the optimal PEG density on the polymeric microspheres is 15 g/100 g. Triphase catalysts offer many advantages associated with heterogeneous catalysts such as easy separation from the reaction mixture and reusability. The activity of PEG‐GMA/MMA microspheres is not nearly decreased after reusing of 10 recycles. © 2009 American Institute of Chemical Engineers AIChE J, 2010     

Preparation of microwave radiation induced graft copolymers and their applications as reinforcing material in phenolic composites

Flax fiber was modified through grafting of binary vinyl monomers mixtures such as methyl methacrylate (MMA)/vinyl acetate (VA), MMA/acrylamide (AAm), and MMA/styrene (Sty) under the influence of microwave radiations. 24.64% grafting was found at 210 W microwave power under optimum reaction conditions. Graft copolymers obtained were characterized with FTIR spectroscopy, scanning electron microscopy, and TGA/DTA techniques. Graft copolymers were found to be moisture retardant with better tensile strength. Phenolic composites using graft copolymers vis‐à‐vis flax as reinforcing material were subjected for the evaluation of different mechanical properties such as wear resistance, tensile strength, compressive strength, modulus of rupture (MOR), modulus of elasticity (MOE), and stress at the limit of proportionality (SP). Composites reinforced with graft copolymers showed better mechanical properties in comparison to composites reinforced with flax. Phenolic composites reinforced with Flax‐g‐poly(MMA/Sty) showed maximum wear resistance followed by reinforcement with flax, Flax‐g‐poly (MMA/AAm), and Flax‐g‐poly(MMA/VA). Composites reinforced with Flax‐g‐poly(MMA/Sty) and flax fibers have been found to show 150 N tensile strength with extension of 3.94 and 2.17 mm, respectively. It has also been found that composites reinforced with Flax‐g‐poly(MMA/Sty) showed maximum compressive strength (1,000 N) with compression of 3.71 mm in comparison to other graft copolymers and flax fibers reinforcement. Reinforcement of phenolic resin with Flax‐g‐poly(MMA/Sty) and flax fibers could improve the MOR and MOE. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Effect of methyl methacrylate content on coatings’ properties of palm oleic acid-based macromer

The macromer was synthesized using medium oil length oleic acid, phthalic anhydride, and glycerol. The synthesized macromer and methyl methacrylate (MMA) were copolymerized by free radical polymerization in toluene. The ratio between the macromer and MMA changed, and the effects on different properties of the copolymers, such as glass transition temperature (T _g) and film properties, were studied. The macromer and copolymer structures were characterized by FTIR and ¹H NMR spectroscopies. The coatings prepared with the highest ratio of MMA exhibited better overall physico-chemical properties. Alternatively, Tafel polarization curves showed that the corrosion rate value in NaCl solution decreases significantly when the MMA content is increased. Dynamic mechanical analysis results revealed that the increasing amounts of MMA lead to increasing T _g values of copolymers.     

Synthesis and properties of novel fluoroalkyl end‐capped oligomers containing silsesquioxane segments

Fluoroalkyl end‐capped homo‐ and co‐ oligomers containing silsesquioxane segments were prepared by the reactions of fluoroalkanoyl peroxides with the corresponding methacrylate monomer‐bearing silsesquioxane unit (Si‐MMA) and comonomers such as N,N‐dimethylacrylamide (DMAA) and acrylic acid (ACA). These new fluorinated Si‐MMA oligomers were easily soluble in various organic solvents and were able to reduce the surface tension of m‐xylene effectively. The modified poly(methyl methacrylate) [PMMA] and glass surface treated with fluorinated Si‐MMA homo‐oligomers exhibited a strong oleophobicity, although these fluorinated oligomers possess high oleophilic silsesquioxane segments. In contrast, the modified PMMA surface treated with fluorinated Si‐MMA–DMAA cooligomers exhibited a good hydrophilicity with a strong oleophobicity. In a series of fluorinated Si‐MMA oligomers, fluorinated Si‐MMA homo‐oligomers had a relatively high thermal stability. Therefore, these fluoroalkyl end‐capped Si‐MMA oligomers are suggested to have high potential for new functional materials through their unique properties such as a high solubility and surface active properties. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3486–3493, 2002     

Free radical polymerizations of some vinyl monomers in carbon dioxide fluid

The effect of pressure ranging from ambient atmosphere to 28.5 MPa on the free radical polymerizations of methyl methacrylate (MMA) in carbon dioxide (CO₂) was investigated and discussed. The poly(methyl methacrylate) (PMMA) with high molecular weight was synthesized at quite high conversion of MMA in the polymerization at or below 9.2 MPa, as compared to those polymerized under 11.8–28.5 MPa. A phase transition behavior of MMA‐CO₂ binary mixture from homogeneous state to vapor‐liquid equilibrium (VLE) state was observed below 10.51 MPa. In such a VLE system, almost all MMA was found to exist in the liquid phase with higher concentration than that in homogenous system. Thus, the fast polymerization rate of MMA and high molecular weight of PMMA could be related to the VLE state of MMA/CO₂ under low pressure. Similar phenomena were also observed in the polymerization systems of styrene and vinyl acetate in CO₂, respectively. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Polyethylenimine‐grafted and HSA‐immobilized poly(GMA–MMA) affinity adsorbents for bilirubin removal

The epoxy‐group‐containing microspheres from cross‐linked glycidyl methacrylate and methyl methacrylate, poly(GMA–MMA), were prepared by suspension polymerisation. The epoxy groups of the poly(GMA–MMA) microspheres were used for grafting with an anionic polymer polyethylenimine (PEI) to prepare non‐specific affinity adsorbents (poly(GMA–MMA)–PEI) for bilirubin removal. The specificity of the poly(GMA–MMA)–PEI adsorbent to bilirubin was further increased by immobilization of human serum albumin (HSA) via adsorption onto PEI‐grafted poly(GMA–MMA) adsorbent. Various amounts of HSA were immobilized on the poly(GMA–MMA)–PEI adsorbent by changing the medium pH and initial HSA concentration. The maximum HSA content was obtained at 68.3 mg g^?1 microspheres. The effects of pH, ionic strength, temperature and initial bilirubin concentration on the adsorption capacity of both adsorbents were investigated in a batch system. Separation of bilirubin from human serum was also investigated in a continuous‐flow system. The bilirubin adsorption on the poly(GMA–MMA)–PEI and poly(GMA–MMA)–PEI–HSA was not well described by the Langmuir model, but obeyed the Freundlich isotherm model. The poly(GMA–MMA)–PEI affinity microspheres are stable when subjected to sanitization with sodium hydroxide after repeated adsorption–desorption cycles. Copyright © 2004 Society of Chemical Industry     

无规甲基化β-环糊精对甲基丙烯酸甲酯无皂乳液聚合影响

采用溶液法制备了无规甲基化β-环糊精(RAMEB)/甲基丙烯酸甲酯(MMA)包合物,利用紫外-可见光谱、热重-差热分析等检测手段表明RAMEB与MMA可以形成摩尔比为1∶1的包合物,从而使MMA的热稳定性大大提高。通过RAMEB与MMA的包合作用研究了RAMEB对MMA无皂乳液聚合反应的影响。结果表明,当RAMEB的加入量为4.2×10-4mol时,体系在75℃反应30 min时,单体转化率达89.2%,比同一时间下没有加入RAMEB的空白样的单体转化率提高了30.6%。当RAMEB的加入量为8.4×10-4mol时,聚合反应速率比空白样低,单体的最终转化率与空白样差不多。同时,RAMEB的引入可以使PMMA微球粒径变大,随着RAMEB加入量的增加,聚合物微球的大小越来越均匀。     

Graft‐modified HCPE with methyl methacrylate by the mechanochemistry reaction. II. Physical‐mechanical properties and processability

In this article, the physical‐mechanical properties and processability of graft‐modified highly chlorinated polyethylene (HCPE; chlorine contents: ≥ 60%) with methyl methacrylate (MMA) by mechanochemistry reaction were studied. The results showed that the HCPE‐g‐MMA system is superior to unmodified HCPE in physical‐mechanical properties, particularly in processability. In addition, the HCPE‐g‐MMA system, with about 62% chlorine content, was the same as PVC in its physical‐mechanical properties. The HCPE‐g‐MMA system, with about 65.5% chlorine content, is the same as chlorinated poly(vinyl chloride) (CPVC) in its physical‐mechanical properties, except that the Vicat softening temperature and processability of HCPE‐g‐MMA system are superior to PVC and CPVC. Compared with PVC and CPVC, the HCPE‐g‐MMA system proves better due to its lack of a toxic monomer. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 282–287, 2004     

An interesting contrast: effects of maleic acid and styrene on the synthesis of functional poly(methyl methacrylate) microspheres

The effects of maleic acid and styrene on the polymerization of methyl methacrylate (MMA) have been studied. Both comonomers play a considerable role in terms of particle size and MMA conversion. The polymerization of MMA in the presence of maleic acid can result in larger particles and a higher MMA conversion. However, in the presence of styrene, the polymerization process yields smaller particles and low MMA conversion. This can be related to the different properties of maleic acid and styrene. Maleic acid, a hydrophilic and electron‐withdrawing comonomer, can play a positive role in stabilizing the particles and increasing MMA activation. However, for styrene, these effects are reversed due to its opposite properties. The change in particle size may be caused by the change in particle stabilization. The change of MMA conversion can be kinetically attributed to the effects of maleic acid and styrene on the activation process. Copyright © 2004 Society of Chemical Industry     

Preparation and comparative evaluation of well-defined fluorinated acrylic copolymer latex and solution for ancient stone protection

In this work the well-defined fluorinated acrylic copolymer latex and solution were prepared by the radical initiated seed emulsion polymerization and solution polymerization, respectively, using the same monomers of dodecafluoroheptyl methacrylate (DFHM), butyl acrylate (BA) and methyl methylacrylate (MMA). The copolymer latex BA/MMA/DFHM was designed as core–shell structure and the copolymer solution poly(BA–MMA–DFHM) was structured with low molecular weight. The chemical and morphology structures as well as the film properties obtained from latex and solution were analyzed and compared by spectroscopic techniques (FT-IR and NMR), transmission electron microscopy (TEM), differential scanning calorimetry (DSC), gel permeation chromatography (GPC), scanning electron microscopy coupled with energy-dispersive X-ray detector (SEM–EDX) and static contact angles (CAs) instrument. Moreover, the BA/MMA/DFHM latex and poly(BA–MMA–DFHM) solution (with 29 wt% of DFHM) were applied onto two kinds of sandstone samples by capillary absorption, and their preliminary protecting efficiency was evaluated. It is demonstrated that the comprehensive performances of BA/MMA/DFHM latex films were quite comparable to those of poly(BA–MMA–DFHM) solution cast films, the latter exhibited a better protective performance.     

A Novel Process for Ultrasound‐Induced Radical Polymerization in CO2‐Expanded Fluids

Summary: A strong viscosity increase upon polymerization hinders cavitation and subsequent radical formation during an ultrasound‐induced bulk polymerization. In this work, ultrasound‐induced radical polymerizations of methyl methacrylate (MMA) have been performed in CO₂‐expanded MMA in order to reduce the viscosity of the reaction mixture. For this purpose, the phase behavior of CO₂/MMA systems has been determined. With temperature oscillation calorimetry, the influence of CO₂ on the viscosity and on the reaction kinetics of ultrasound‐induced polymerizations of MMA has been studied. In contrast to polymerizations in bulk, this technique shows that a low viscosity is maintained during polymerization reactions in CO₂‐expanded MMA. As a consequence, a constant or even increasing polymerization rate is observed when pressurized CO₂ is applied. Moreover, the ultrasound‐induced polymer scission in CO₂‐expanded MMA is demonstrated, which appears to be a highly controlled process. Finally, a preliminary sustainable process design is presented for the production of 10 kg/h pure PMMA (specialty product) in CO₂‐expanded MMA by ultrasound‐induced initiation.

Process flow diagram of the ultrasound‐induced polymerization of MMA in CO₂‐expanded MMA.     

Copolymers of methyl methacrylate with cinnamic acid

Methyl methacrylate (MMA) and cinnamic acid (CA) have been copolymerized radically at 60°C; the amounts of CA incorporated in copolymers are surprisingly low. The CA units sensitize the MMA units towards alkaline hydrolysis. The copolymers are less soluble than the homopolymer of MMA in toluene; their thermal stabilities are significantly higher and their glass transition temperatures are slightly lower.     

Morphologies and dynamic mechanical properties of core‐shell emulsifier‐free latexes and their copolymers for P(BA/MMA)/P(MMA/BA) and P(BA/MMA)/PSt systems in the presence of AHPS

Different poly(methyl methacrylate/n‐butyl acrylate)/poly(n‐butyl acrylate/methyl methacrylate) [P(BA/MMA)/P(MMA/BA)] and poly(n‐butyl acrylate/methyl methacrylate)/polystyrene [P(BA/MMA)/PSt] core‐shell structured latexes were prepared by emulsifier‐free emulsion polymerization in the presence of hydrophilic monomer 3‐allyloxy‐2‐hydroxyl‐propanesulfonic salt (AHPS). The particle morphologies of the final latexes and dynamic mechanical properties of the copolymers from final latexes were investigated in detail. With the addition of AHPS, a latex of stable and high‐solid content (60 wt %) was prepared. The diameters of the latex particles are ～0.26 μm for the P(BA/MMA)/P(MMA/BA) system and 0.22–0.24 μm for the P(BA/MMA)/PSt system. All copolymers from the final latexes are two‐phase structure polymers, shown as two glass transition temperatures (T_gs) on dynamic mechanical analysis spectra. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3078–3084, 2002