Synergistic effect of three‐dimensional multi‐walled carbon nanotube–graphene nanofiller in enhancing the mechanical and thermal properties of high‐performance silicone rubber

The homogeneous dispersion of nanofillers and filler–matrix interfacial interactions are important factors in the development of high‐performance polymer materials for various applications. In the present work, a simple solution‐mixing method was used to prepare multi‐walled carbon nanotube (MWCNT)–graphene (G) (3:1, 1:1, 1:3) hybrids followed by their characterization through wide‐angle X‐ray diffraction, transmission electron microscopy and thermogravimetric analyses. Subsequently, MWCNT–G (1:1) hybrid was used as reinforcing filler in the formation of silicone rubber (VMQ) nanocomposites by solution intercalation, and their morphology and properties were investigated. Our findings showed that MWCNT–G (0.75 wt%)/VMQ composite exhibited significant improvements in tensile strength (110%) and Young's modulus (137%) compared to neat VMQ. The thermal stability of MWCNT–G (1 wt%)/VMQ was maximally improved by 154 °C compared to neat VMQ. Differential scanning calorimetry demonstrated the maximum improvement of glass transition temperature (4 °C), crystallization temperature (8 °C) and melting temperature (5 °C) for MWCNT–G (1 wt%)/VMQ nanocomposite with respect to neat VMQ. Swelling measurements confirmed that the crosslink density and solvent resistance were a maximum for hybrid nanocomposites. Such improvements in the properties of MWCNT–G/VMQ nanocomposites could be attributed to a synergistic effect of the hybrid filler. © 2013 Society of Chemical Industry     

Multiwalled carbon nanotube/montmorillonite hybrid filled ethylene‐co‐vinyl acetate nanocomposites with enhanced mechanical properties,thermal stability,and dielectric response

Homogeneous multiwalled carbon nanotube/montmorillonite hybrid filler (HMM) dispersion was prepared by co‐ultrasonication and was subsequently used to prepare ethylene‐co‐vinyl acetate (EVA) nanocomposites by solution blending method. XRD and TEM analysis of HMM confirm significant interaction between the montmorillonite (MMT) layers and multiwalled carbon nanotubes (MWCNT) in line with previous reports. Analysis of the nanocomposites shows the constituent fillers to be homogeneously dispersed in EVA matrix. Mechanical properties of neat EVA are remarkably improved with HMM content up to 3 wt% followed by reversion. Maximum improvement observed in tensile strength, elongation at break, and toughness are 424%, 109%, and 1122%, respectively. Results show maximum thermal stability at 4 wt% and best dielectric response at 1 wt% HMM content. Exceptional mechanical and dielectric properties of EVA nanocomposites attained may be attributed to homogeneous dispersion of fillers and improved polymer–filler interaction. Comparison shows excellent synergy between MWCNT and MMT towards mechanical reinforcement of EVA. POLYM. ENG. SCI., 58:1155–1165, 2018. © 2017 Society of Plastics Engineers     

Crystallization behavior and mechanical strength of poly(butylene succinate‐co‐ethylene glycol)‐based nanocomposites using functionalized multiwalled carbon nanotubes

Biodegradable poly(butylene succinate‐co‐ethylene glycol) (PBSG)/multiwalled carbon nanotube (MWCNT) nanocomposites were successfully prepared through physical blending and silication between PBSG and acyl aminopropyltriethoxysilane functionalized multiwalled carbon nanotube (MWCNT‐APTES). Nuclear magnetic resonance (NMR) spectra observations revealed that the PBSG chains were covalently attached to the MWCNT‐APTES by hydrolysis. PBSG/MWCNT‐APTES nanocomposites after hydrolysis showed excellent interfacial compatibility between PBSG and MWCNT‐APTES, which was helpful for the dispersion of MWCNT in the PBSG matrix. The incorporation of MWCNT‐APTES accelerated the crystallization of PBSG in the nanocomposites for both approaches of physical blending and hydrolysis due to the heterogeneous nucleation effect of MWCNT while the crystal structure of PBSG was remained. Furthermore, the crystallization rate of PBSG in PBSG/MWCNT‐APTES nanocomposites after hydrolysis was slower than that in the nanocomposite by physical blend. The tensile strength and modulus of the nanocomposites increased about 6% and 11% with the addition of only 1 wt% MWCNT‐APTES compared with that of neat PBSG, and was larger for the PBSG/MWCNT‐APTES nanocomposites after hydrolysis. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Montmorillonite–multiwalled carbon nanotube nanoarchitecture reinforced thermoplastic polyurethane

Montmorillonite (MMT)–multiwalled carbon nanotube (MWCNT) hybrids were prepared in different weight ratios by simple dry grinding method and characterized. Subsequently, MMT–MWCNT (1:1) hybrid was used as reinforcing filler in developing thermoplastic polyurethane (TPU) nanocomposites by solution blending method. Thermogravimetric analysis showed that 0.25 wt% hybrid‐loaded TPU nanocomposite exhibited maximum enhancement of 31°C corresponding to 50 wt% loss in thermal stability when compared with neat TPU. Differential scanning calorimetry of this composite also indicated that its crystallization and melting temperatures are enhanced by 37 and 13°C, respectively. Mechanical data showed that tensile strength and Young's modulus of 0.50 wt% filled TPU were maximum improved by 57 and 87.5%, respectively. Dynamic mechanical analysis (DMA) measurements indicated 174% (50°C) improvement in storage modulus of 0.50 wt% hybrid‐loaded TPU. Such improvements in thermal and mechanical properties have been attributed to homogeneous dispersion, strong interfacial interaction, and synergistic effect. POLYM. COMPOS., 37:1775–1785, 2016. © 2014 Society of Plastics Engineers     

Cellulose acetate/multiwalled carbon nanotube nanocomposites with improved mechanical,thermal, and electrical properties

Cellulose acetate (CA)‐based nanocomposites with various contents of neat multiwalled carbon nanotube (MWCNT) or acid‐treated one (MWCNT‐COOH) are prepared via melt‐compounding method and investigated their morphology, thermal stability, mechanical, and electrical properties. SEM microphotographs reveal that MWCNT‐COOHs are dispersed uniformly in the CA matrix, compared with neat MWCNTs. FTIR spectra support that there exists a specific interaction between carboxyl groups of MWCNT‐COOHs and ester groups of CA, indicating good interfacial adhesion between MWCNT‐COOHs and CA matrix. Accordingly, thermal stability and dynamic mechanical properties of CA/MWCNT‐COOH nanocomposites were higher than those of CA/MWCNT composites. On the contrary, electrical volume resistivities of CA/MWCNT‐COOH nanocomposites are found to be somewhat higher than those of CA/MWCNT composites, which is because of the deterioration of graphene structures for MWCNT‐COOHs and the good dispersion of MWCNT‐COOHs in the CA matrix. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Improved impact strength of epoxy by the addition of functionalized multiwalled carbon nanotubes and reactive diluent

Multiwalled carbon nanotubes (MWCNTs), both oxidized and amine functionalized (triethylenetetramine—TETA), have been used to improve the mechanical properties of nanocomposites based on epoxy resin. The TGA and XPS analysis allowed the evaluation of the degree of chemical modification on MWCNTs. Nanocomposites were manufactured by a three‐roll milling process with 0.1, 0.5, and 1.0 wt % of MWCNT–COOH and MWCNT–COTETA. A series of nanocomposites with 5.0 wt % of reactive diluent was also prepared. Tensile and impact tests were conducted to evaluate the effects of the nanofillers and diluent on the mechanical properties of the nanocomposites. The results showed higher gains (258% increase) in the impact strength for nanocomposites manufactured with aminated MWCNTs. Optical microscopy (OM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) were used to investigate the overall filler distribution, the dispersion of individual nanotubes, and the interface adhesion on the nanocomposites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42587.     

Enhanced properties of phthalonitrile‐terminated polyarylene ether nitriles embedded with hybrid MWCNT–boehmite nanocomposites

The main motivation of the present work was to fabricate novel multifunctional polymer‐based nanocomposites. The nanocomposites embedded with multi‐walled carbon nanotube‐boehmite (MWCNT‐boehmite) were prepared via hot pressure casting technique. The MWCNT coated with boehmite were synthesized by hydrothermal synthesis. Subsequently, as‐prepared MWCNT‐boehmite was added into the phthalonitrile‐terminated polyarylene ether nitriles (PEN‐t‐CN) matrix in order to benefit from the synergetic effect of MWCNT and boehmite. Scanning electron microscopy (SEM), transmission electron microscopy (TEM) X‐ray diffraction (XRD), and Fourier transform infrared (FTIR) were employed to confirm the existence of MWCNT‐boehmite in our article. Furthermore, the structures, fracture morphologies, thermal, mechanical and dielectric properties of the nanocomposites were investigated, respectively. SEM images indicated that the MWCNT‐boehmite was homogeneously dispersed in the polymer, which acted as an essential factor to ensure good physical properties. The TGA analysis showed that the incorporation of MWCNT‐boehmite enhanced the thermal stability of the nanocomposites with initial degradation temperature (T_id) increasing from 458 to 492°C, while that of the pure PEN‐t‐CN was 439°C. The mechanical testing proved that significant enhancement of mechanical properties has been achieved. The tensile strength of PEN‐t‐CN/MWCNT‐boehmite composites with 3 wt% MWCNT‐boehmite reached the maximum (78.33 MPa), with a 41.7 % increase compared to the pure polymer. More importantly, the unique dielectric properties were systematically discussed and the results demonstrated that dielectric properties exhibited little dependency on frequency. For the incorporation of hybrid filler, the positive impact of MWCNT‐boehmite hybrid material resulted in polymer‐based nanocomposites with enhanced physical properties. POLYM. COMPOS., 36:2193–2202, 2015. © 2014 Society of Plastics Engineers     

Oxidized multiwalled carbon nanotubes as effective reinforcement and thermal stability agents of poly(lactic acid) ligaments

In this study, nanocomposites of poly(lactic acid) (PLA) containing 0.5, 1, and 2.5 wt % oxidized multiwalled carbon nanotubes (MWCNT–COOHs) were prepared by the solved evaporation method. From transmission electron microscopy and scanning electron microscopy micrographs, we observed that the MWCNT–COOHs were well dispersed in the PLA matrix and, additionally, there was increased adhesion between PLA and the nanotubes. As a result, all of the studied nanocomposites exhibited higher mechanical properties than neat PLA; this indicated that the MWCNT–COOHs acted as efficient reinforcing agents, whereas in the nonoxidized multiwalled carbon nanotubes, the mechanical properties were reduced. Nanotubes can act as nucleating agents and, thereby, affect the thermal properties of PLA and, especially, the crystallization rate, which is faster than that of neat PLA. From the thermogravimetric data, we observed that the PLA/MWCNT–COOH nanocomposites presented relatively better thermostability than PLA; this was also verified from the calculation of activation energy. On the contrary, the addition of MWCNT–COOH had a negative effect on the enzymatic hydrolysis rate of PLA. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

TPU/PLA nanocomposites with improved mechanical and shape memory properties fabricated via phase morphology control and incorporation of multi-walled carbon nanotubes nanofillers

Shape memory polymer nanocomposites based on thermoplastic polyurethane (TPU)/polylactic acid (PLA) blends filled with pristine multi-walled carbon nanotubes (MWCNTs) and modified MWCNTs─COOH were fabricated by direct melt blending technique and investigated for its morphology, mechanical, thermal, electrical, and shape memory properties. Morphological characterizations by using transmission electron microscope (TEM) and field emission scanning electron microscope (FESEM) revealed better dispersion of MWCNTs─COOH in the polymer blend, which is attributed to the improved interfacial interactions between the polymer blends and MWCNTs-COOH. Loading of the MWCNTs-COOH in the TPU/PLA blends resulted in the significant improvements in the mechanical properties such as tensile strength and elastic modulus and these effects are more pronounced on increasing the MWCNTs─COOH loading amount, when compared to the pristine MWCNTs filled system. Thermal analysis showed that the glass transition temperature of the blends increases slightly with increasing loading of both pristine and modified MWCNTs in the system. The resistance of nanocomposites decreased from 2 × 10¹² Ω to 3.2 × 10¹⁰ Ω after adding 3% MWCNTs─COOH. The shape memory performance tests showed that the enhancement of shape recovery by 252% could be achieved at 3% MWCNTs loading, when compared to that of TPU/PLA blends.     

Effect of carbon nanoparticle type,content, and stress on piezoresistive polyethylene nanocomposites

This study examines the piezoresistive behavior of polyethylene (PE) composites containing different types of carbon nanoparticle fillers. The fillers investigated are single‐wall carbon nanotube (SWCNT), multi‐wall carbon nanotube (MWCNT), and graphene nanoplatelets (GNP), which were dispersed in PE through melt blending in concentrations ranging between 0.5 and 10 wt%. The dispersion and nanocomposite morphology were investigated using scanning electron microscopy and X‐ray diffraction with strong evidence found for shear‐induced orientation of GNP nanoparticles during the compression molding process. The conductivity and permittivity of the composite materials was investigated using impedance spectroscopy and the lowest percolation threshold and highest electrical conductivity was observed for SWCNT composites, followed by MWCNT and GNP. The compressive piezoresistance of the nanocomposites was measured and the initial, elastic, and plastic deformation regions were all identifiable by the resistance measurements. The main finding of this study is that the piezoresistance of MWCNT nanocomposites is more sensitive to the effects of varying stress and composition than SWCNT nanocomposites. This indicates an evolving filler network in the case for MWCNT, while a static network for SWCNT, which is explained by the higher aspect ratio and surface area of the latter. POLYM. ENG. SCI., 55:1643–1651, 2015. © 2014 Society of Plastics Engineers     

Graphene Nanoplatelets as Novel Reinforcement Filler in Poly(lactic acid)/Epoxidized Palm Oil Green Nanocomposites: Mechanical Properties

Graphene nanoplatelet (xGnP) was investigated as a novel reinforcement filler in mechanical properties for poly(lactic acid) (PLA)/epoxidized palm oil (EPO) blend. PLA/EPO/xGnP green nanocomposites were successfully prepared by melt blending method. PLA/EPO reinforced with xGnP resulted in an increase of up to 26.5% and 60.6% in the tensile strength and elongation at break of the nanocomposites respectively, compared to PLA/EPO blend. XRD pattern showed the presence of peak around 26.5° in PLA/EPO nanocomposites which corresponds to characteristic peak of graphene nanoplatelets. However, incorporation of xGnP has no effect on the flexural strength and modulus. Impact strength of PLA/5 wt% EPO improved by 73.6% with the presence of 0.5 wt% xGnP loading. Mechanical properties of PLA were greatly improved by the addition of a small amount of graphene nanoplatelets (<1 wt%).     

Functionalization of carbon nanotubes and carbon nanofibers used in epoxy/amine matrices that avoid partitioning of the monomers at the fiber interface

Single‐wall carbon nanotubes (SWCNT), multiwall carbon nanotubes (MWCNT), and carbon nanofibers (CNF) were oxidized with a conventional H₂SO₄/HNO₃ treatment, and the resulting COOH groups were esterified with phenyl glycidyl ether (PGE). Pristine, oxidized and esterified SWCNT, MWCNT, and CNF (1 wt%) were dispersed in diglycidyl ether of bisphenol A/polyether triamine, and cured to produce epoxy nanocomposite. The quality of the dispersion varied with surface modification in the order: COOH > unmodified > PGE, as assessed for SWCNT/epoxy composites using radial breathing modes in Raman spectra and scanning electron microscopy. Local bundling of PGE‐modified nanofillers was explained by a polymerization‐induced phase‐separation process. Dynamic mechanical analysis showed the presence of two relaxation peaks in nanocomposites prepared with unmodified and COOH‐modified SWCNT, MWCNT, and CNF, assigned to a partitioning of monomers at the carbon interface. This produced a significant decrease of the glass transition temperature. However, the esterification with PGE led to a single relaxation peak close to the one of the neat epoxy, for the three types of nanofillers without any penalty in the glassy and rubbery elastic moduli. The effect was explained by matrix exclusion from phase‐separated domains. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers     

Mechanical,thermal and electrical properties of multi‐walled carbon nanotube/aluminium nitride/polyetherimide nanocomposites

A series of polyimide‐based nanocomposites containing polyimide‐grafted multi‐walled carbon nanotubes (PI‐g MWCNTs) and silane‐modified ceramic (aluminium nitride (AlN)) were prepared. The mechanical, thermal and electrical properties of hybrid PI‐g MWCNT/AlN/polyetherimide nanocomposites were investigated. After polyimide grafting modification, the PI‐g MWCNTs showed good dispersion and wettability in the polyetherimide matrix and imparted excellent mechanical, electrical and thermal properties. The utilization of the hybrid filler was found to be effective in increasing the thermal conductivity of the composites due to the enhanced connectivity due to the high‐aspect‐ratio MWCNT filler. The use of spherical AlN filler and PI‐g MWCNT filler resulted in composite materials with enhanced thermal conductivity and low coefficient of thermal expansion. Results indicated that the hybrid PI‐g MWCNT and AlN fillers incorporated into the polyetherimide matrix enhanced significantly the thermal stability, thermal conductivity and mechanical properties of the matrix. Copyright © 2012 Society of Chemical Industry     

Nonlinear viscoelasticity and stress‐softening behavior of chloroprene rubber reinforced by multiwalled carbon nanotubes

The viscoelasticity and stress‐softening behavior of chloroprene rubber (CR) filled with multiwalled carbon nanotubes (MWCNT) and carboxylated multiwalled carbon nanotubes (MWCNT‐COOH) were studied using a Rubber Process Analyzer 2000 (RPA2000). In the strain sweep measurements, it is found that CR/MWCNT and CR/MWCNT‐COOH compounds have different behavior on storage modulus (G′). With increasing strain, G′ of CR/MWCNT (100/8) compound decreases at strain less than 2°, while G′ of CR/MWCNT‐COOH (100/8) compound stays at constant, indicating that MWCNT‐COOH has stronger filler–filler network and filler–rubber interactions as compared to MWCNT in CR matrix. CR/MWCNT (MWCNT‐COOH) vulcanizates have higher G′ but lower loss modulus (G″) than the corresponding uncured compounds. Repeated strain sweep scans were carried out to study the stress‐softening behavior of CR compounds. A stress‐softening effect of the filled CR compounds is observed and becomes more pronounced with increasing loading of MWCNT or MWCNT‐COOH. The correlation between the Payne effect and stress‐softening effect of CR/MWCNT (MWCNT‐COOH) vulcanizates is also studied. It is found that the difference of the storage moduli at 0.1° and 10° strain amplitudes and the difference of storage moduli of first and second strain sweeps at 0.1° strain amplitude show a positive linear correlation. POLYM. COMPOS., 35:2194–2202, 2014. © 2014 Society of Plastics Engineers     

Enzyme‐Catalyzed Synthesis of Conducting Polyaniline Nanocomposites with Pure and Functionalized Carbon Nanotubes

The in situ enzymatic polymerization of aniline onto multi‐walled carbon nanotubes (MWCNT) and carboxylated MWCNT (COOH‐MWCNT) is reported. Nanostructured composites were prepared by this method. Polymerization was catalyzed with the enzyme horseradish peroxidase at room temperature in aqueous medium of pH 4. Hydrogen peroxide was used in low concentration as the oxidant. The nanocomposites were characterized by Fourier transform infrared spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and thermogravimetric analysis (TGA). The TEM studies showed tubular morphology with uniformly distributed MWCNT in the nanocomposites. The SEM and TEM investigations revealed wrapping of the MWCNT with polyaniline (PANI) chains. TGA demonstrated that the PANI component is thermally more stable in PANI/COOH‐MWCNT compared to the PANI/MWCNT composites. The synthesized nanocomposites showed higher conductivity than pure PANI, which may be due to the strong interaction between the PANI chains and the MWCNT.     

Amino functionalization of multiwalled carbon nanotubes by gamma ray irradiation and its epoxy composites

In this paper, γ‐ray radiation technique was utilized to simply functionalize multi‐walled carbon nanotube (MWCNT) with amino groups. The successful amino functionalization of MWCNTs (MWCNTs‐Am) was proven and the physicochemical properties of MWCNTs before and after radiation grafting modifications were characterized using FT‐IR, X‐ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and thermogravimetric analysis (TGA). The results indicated that the γ‐ray radiation had the visible effects on the surface properties of MWCNTs. The effects of various functionalized MWCNTs on morphological, thermal, and mechanical properties of an epoxy‐based nanocomposite system were investigated. Utilizing in situ polymerization, 1 wt% loading of MWCNT was used to prepare epoxy‐based nanocomposites. Compared to the neat epoxy system, nanocomposites prepared with MWCNT‐Am showed 13.0% increase in tensile strength, 20.0% increase in tensile modulus, and 24.1% increase in thermal decomposition temperature. POLYM. COMPOS., 2012. © 2011 Society of Plastics Engineers     

Effect of cooling rate on the surface resistivity of polymer/multi‐walled carbon nanotube nanocomposites

In this study, ethylene‐vinyl acetate copolymer (EVA) and polystyrene (PS) were melt‐mixed with multi‐walled carbon nanotube (CNT) (MWCNT), respectively. The effect of mixing time, rotor speed, and cooling rate on surface resistivity was investigated. EVA/MWCNT and PS/MWCNT nanocomposites with percolation threshold <1 wt% of MWCNT were prepared using conventional melt‐compounding method. When fast cooling was applied for these nanocomposites, a surface resistivity of 10⁶ Ω/square was obtained at around 7 wt% of MWCNT for EVA and 10⁵ Ω/square at around 3.5 wt% of MWCNT for PS. However, when slow cooling was applied, a surface resistivity of 10⁶ Ω/square was obtained at 0.75 wt% of MWCNT for EVA and 10⁵ Ω/square at around 0.5 wt% of MWCNT for PS. To the best of our knowledge, this is the first report which recognizes the importance of cooling rate on the surface resistivity of polymer/MWCNT nanocomposites. This finding may be potential to the commercialization of the CNT‐based polymer nanocomposites. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Electromagnetic interference shielding effectiveness of MWCNT filled poly(ether sulfone) and poly(ether imide) nanocomposites

Multiwalled carbon nanotube (MWCNT) filled poly(ether sulfone) (PES) and poly(ether imide) (PEI) composites were prepared with different MWCNT weight fractions (0.5–5wt%) by a solution mixing technique. Their electrical conductivities, electromagnetic interference (EMI), shielding effectiveness (SE), return loss (RL), and absorption loss (AL) were investigated. Morphologies of the fracture surfaces of nanocomposites studied by scanning electron and transmission electron microscopy showed relatively good MWCNT dispersion and distribution. The electrical conductivity of compression molded samples measured at room temperature indicated that the electrical percolation network was achieved already at 0.5% loading. The measurements of shielding effectiveness (SE) carried out in the frequency range of 8 to 12 GHz (X‐band range) showed that SE increases with measurement frequency and with filler loading, whereby no significant differences could be observed between PES and PEI as matrices. The nanocomposites based on both matrices with 5 wt% loading of MWCNT exhibited shielding levels at 8 GHz between 42 and 45 dB in comparison with the pure polymers which showed value in the range of 1 to 2 dB. RL and AL showed significantly lower values for the composites as compared to unfilled polymers, but no systematic trends were observed on frequency. POLYM. ENG. SCI., 54:2560–2570, 2014. © 2013 Society of Plastics Engineers     

Effects of thermoplastic polyurethane on the properties of poly(lactic acid)/organo‐montmorillonite nanocomposites based on novel vane extruder

Polylactic acid (PLA)/organo‐montmorillonite (OMMT) nanocomposites toughened with thermoplastic polyurethane (TPU) were prepared by melt‐compounding on a novel vane extruder (VE), which generates global dynamic elongational flow. In this work, the mechanical properties of the PLA/TPU/OMMT nanocomposites were evaluated by tensile, flexural, and tensile tests. The wide‐angle X‐ray diffraction and transmission electron microscopy results show that PLA/TPU/OMMT nanocomposites had clear intercalation and/or exfoliation structures. Moreover, the particles morphology of nanocomposites with the addition of TPU was investigated using high‐resolution scanning electronic microscopy. The results indicate that the spherical TPU particles dispersed in the PLA matrix, and the uniformity decreased with increasing TPU content (≤30%). Interestingly, there existed abundant filaments among amount of TPU droplets in composites with 30 and 40 wt% TPU. Furthermore, the thermal properties of the nanocomposites were examined with differential scanning calorimeter and dynamic mechanical analysis. The elongation at break and impact strength of the PLA/OMMT nanocomposites were increased significantly after addition of TPU. Specially, Elongation at break increased by 30 times, and notched impact strength improved 15 times when TPU loading was 40 wt%, compared with the neat PLA. Overall, the modified PLA nanocomposites can have greater application as a biodegradable material with enhanced mechanical properties. POLYM. ENG. SCI., 54:2292–2300, 2014. © 2013 Society of Plastics Engineers