共查询到20条相似文献,搜索用时 109 毫秒
1.
由北京星宇惠龙公司研发的具有自主知识产权的BCA一2型井下装药车于2006年底在金川集团公司二矿区顺利投入运行。装药车装载非爆炸性乳胶基质和添加剂驶入爆破作业面,由车载装药系统将其装入炮孔后现场敏化成为乳化炸药。每个炮孔的装药作业均由车载自动控制系统自动完成,装药作业安全可靠,计量准确,操作方便,自动化程度高,实现了炮孔耦合装药,对于积水孔、变形孔、上向孔等均能达到良好的装药效果和爆破效果,爆破作业效果好,可较大幅度地提高地下矿山采掘作业的爆破效率。 相似文献
2.
3.
4.
我国矿山地下开采正在由人工装药过渡到装药车机械化、自动化装药。在原装药车上,装药时退管速度恒定,会造成炸药返料、装药管堵塞、爆破效果差等结果。采用PID控制,将退管速度与装药速度做闭环控制,实现连续稳定装药。 相似文献
5.
6.
7.
露天矿浆状炸药装药车的研制 总被引:1,自引:0,他引:1
为实现矿山采矿全面机械化,针对我国露天矿爆破中的传统手工装药的方法,笔者对浆状炸药装药车的研制,从理论与实践上进行了探讨,对该车主要部件的技术问题,提出了解决方案和具体措施。 相似文献
8.
9.
10.
本文研究了地下矿山辅助车辆轻型通用底盘的设计方案,论证了DZY—220地下装药车底盘用做地下轻型通用底盘的可行性。 相似文献
11.
PP炸药车引进美国埃利克(ireco)化学工业公司技术,车上多处液压执行机构采用了摆式液压马达。文中结合对此类液压马达的技术消化,介绍了摆线式马达的工作原理、摆线参数、结构特点、配流形式,并提出了保养维修工作的技术要点和注意事项。 相似文献
12.
13.
14.
分析冷轧酸轧联合机组轧机液压高压系统泄漏的原因,并通过增加液压高压系统泄露监控系统和优化轧机控制系统等措施,使轧机液压高压系统泄漏的现象得到有效控制。 相似文献
15.
16.
17.
G. Fu J. Feng W. Dekelbab F. Moses H. Cohen D. Mertz 《Canadian Metallurgical Quarterly》2008,13(6):556-564
Heavy trucks represent a major load to highway bridges in the transportation infrastructure system. These loads are directly related to the truck weight limits of the jurisdiction, and largely determine the standard loads for bridge design and evaluation. Thus, truck weight limit is one of the major factors affecting bridge deterioration and expenditure for maintenance, repair, and/or replacement. Truck weight in this paper not only refers to the truck gross weight but also to the axle weights and spacings that affect load effects. This paper presents the concepts of a new methodology for estimating cost effects of truck weight limit changes on bridges in a transportation infrastructure network. The methodology can serve as a tool for studying impacts of such changes. The resulting knowledge is needed when examining new truck weight limits, several of which have been and are still being debated at both the state and federal levels in the United States. The development of this estimation method has considered maximizing the use of available data (such as the bridge inventory) at the state infrastructure system level. In application examples completed (but not reported herein), the costs for relatively inadequate strength of existing bridges and for increased design requirement for new bridges were found dominant in the total impact cost. 相似文献
18.
压力控制回路是液压基本控制回路之一,它是利用压力控制阀来控制整个液压系统或局部油路的工作压力,来满足执行元件要达到的工作要求。压力回路出现故障,液压系统就不能正常工作。必须及时诊断,排除故障。由于液压系统的故障大量属于突发性和磨损性故障,是不可预测的,本文仅对压力回路易出的几种故障与排除进行简要说明。 相似文献
19.
八钢中板厂1#液压站系统可设定最高压力19MPa,现场设定为16MPa.通过控制1#、2#出钢机抬升装置等液压缸,抬升装置承接出料杆,实现炉子出钢功能.但在开发一些比较重的钢坯时,为保证抬升缸上升过程正常稳定,设备方将液压站系统压力由原来的16MPa提高到18.5MPa,运行约半年,接连发生抬升缸耳轴断裂、缸头断裂等事故.分析认为液压缸安全系数不够,为此对液压缸结构尺寸及材料进行了改进,运行至今不曾发生故障. 相似文献
20.
本文介绍了宝钢205Omm热轧机精轧机组CVC液压系统利用系统本身设备采用高压大流量冲洗新工艺,在提高冲洗精度、缩短冲洗时间和降低劳动强度等方面都取得了较好的效果。 相似文献