CMOS兼容电容型湿度传感器的理论模型

对一种与CMOS工艺兼容的电容型湿度传感器进行了理论推导,物理建模和模拟仿真.该湿度传感器是采用梳状铝电极结构,聚酰亚胺作为感湿介质.通过分析感湿介质的介电常数吸附水分后的变化,考虑其电场分布,对电容型湿度传感器的理论模型进行了研究和模拟.利用Matlab软件对理论模型进行仿真,结果表明所建模型比通常采用的Laconte模型更符合实验结果.     

CMOS工艺兼容的单片集成湿度传感器

设计并制备了一个CMOS工艺兼容的集成湿度传感器,将湿度传感器与CMOS测量电路集成在同一芯片上.片上集成的湿度传感器为叉指电容式,感湿介质为聚酰亚胺,本文给出了相应的感湿模型.针对湿度传感器在全量程电容变化量较小的特点,本文采用开关电容电路作为片上微电容测量电路,讨论了电路的原理并给出了模拟结果.芯片采用3μm多晶硅栅标准CMOS工艺进行流水.测量结果表明,片上集成湿度传感器在5～35℃有较好的直流输出特性,并且长时间稳定性良好.     

CMOS工艺兼容的单片集成湿度传感器

设计并制备了一个CMOS工艺兼容的集成湿度传感器,将湿度传感器与CMOS测量电路集成在同一芯片上.片上集成的湿度传感器为叉指电容式,感湿介质为聚酰亚胺,本文给出了相应的感湿模型.针对湿度传感器在全量程电容变化量较小的特点,本文采用开关电容电路作为片上微电容测量电路,讨论了电路的原理并给出了模拟结果.芯片采用3μm多晶硅栅标准CMOS工艺进行流水.测量结果表明,片上集成湿度传感器在5～35℃有较好的直流输出特性,并且长时间稳定性良好.     

一种格栅状上电极的CMOS工艺聚酰亚胺电容型湿度传感器

报道了采用标准CMOS工艺制作的格栅型上电极的电容型湿度传感器,采用高分子材料聚酰亚胺作为感湿介质,铝作为金属电极.对该湿度传感器的器件结构、制作工艺和传感器特性,如灵敏度、湿滞以及响应时间等进行了讨论.测试结果表明,在12%～92%的湿度范围内,电容一相对湿度曲线具有良好的线性度,灵敏度为0.9 pF/RH,响应时间...     

一种新型的CMOS集成湿度传感器

利用MEMS技术，对一种新型CMOS湿度传感器进行理论分析、模拟以及结果讨论。该湿度传感器采用标准CMOS工艺制造，采用梳状铝电极结构、梳状多晶硅加热结构，衬底接地，感湿介质采用聚酰亚胺，利用商业软件Coventor进行模拟绘制出敏感电容与相对湿度的曲线图。接口电路采用开关电容电路，输出可测电压信号，利用Microsim公司的Pspice模拟电路得到相对湿度与输出电压曲线关系。     

一种新型的CMOS集成湿度传感器

利用MEMS技术,对一种新型CMOS湿度传感器进行理论分析、模拟以及结果讨论.该湿度传感器采用标准CMOS工艺制造,采用梳状铝电极结构、梳状多晶硅加热结构,衬底接地,感湿介质采用聚酰亚胺,利用商业软件Coventor进行模拟绘制出敏感电容与相对湿度的曲线图.接口电路采用开关电容电路,输出可测电压信号,利用Microsim公司的Pspice模拟电路得到相对湿度与输出电压曲线关系.     

一种新型的CMOS集成湿度传感器

利用MEMS技术 ,对一种新型CMOS湿度传感器进行理论分析、模拟以及结果讨论。该湿度传感器采用标准CMOS工艺制造 ,采用梳状铝电极结构、梳状多晶硅加热结构 ,衬底接地 ,感湿介质采用聚酰亚胺 ,利用商业软件Coventor进行模拟绘制出敏感电容与相对湿度的曲线图。接口电路采用开关电容电路 ,输出可测电压信号 ,利用Microsim公司的Pspice模拟电路得到相对湿度与输出电压曲线关系     

电容型湿度传感器模型计算与分析

以菲克第二扩散定律为基础,建立湿度传感器器件三明治结构模型,对聚酰亚胺电容型湿度传感器进行全面数值模拟,分析其电场分布、升降湿的动态过程及响应时间,并与实验结果进行对比分析.引入了自由体积理论对湿度传感器升、降湿过程的影响,使模拟过程更加符合实际情况,结果显示模拟结果和实验数据吻合良好,并根据对模拟结果分析,发现电极宽度是制约传感器性能的关键参数.该模型能够较准确预测制备的电容型湿度传感器性能,以此来指导高性能湿度传感器研究.     

基于CMOS工艺的硅基PI湿度传感器的研制

在国内外湿度传感器研究的基础上,基于Si CMOS工艺研制出了以聚酰亚胺(PI)为感湿介质的电容型相对湿度传感器.并对其结构进行了理论分析,仔细确定了湿度传感器的工艺步骤和版图设计.对其测量范围、湿滞和响应时间等特性参数进行了详细的测试.通过实验结果与模拟结果的对比分析,给出了该实验中存在的问题和改进意见,以便在今后的研究中加强这方面的工作.     

高分子电容型湿度传感器研制

随着工业的快速发展,对温度检测和控制日益严格,温度传感器已无法跟上人们的需求,通过优化湿度传感器的表面结构和对感湿材料微孔设计提高了感湿特性,增强感湿材料的感湿特性,并对湿度传感器测量电路进行改进,提高微小电容测量,设计湿度测试系统。通过实验验证了改进后的湿度传感器测量效果更优越。     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

GaAsSb/InAlAs PA DHBTs Grown by Production MBE

The epi material growth of GaAsSb based DHBTs with InAlAs emitters are investigated using a 4 × 100mm multi-wafer production Riber 49 MBE reactor fully equipped with real-time in-situ sensors including an absorption band edge spectroscope and an optical-based flux monitor. The state-of-the-art hole mobilities are obtained from 100nm thick carbon-doped GaAsSb. A Sb composition variation of less than ± 0.1 atomic percent across a 4 × 100mm platen configuration has been achieved. The large area InAlAs/GaAsSb/InP DHBT device demonstrates excellent DC characteristics,such as BVCEO＞6V and a DC current gain of 45 at 1kA/cm2 for an emitter size of 50μm × 50μm. The devices have a 40nm thick GaAsSb base with p-doping of 4. 5 × 1019cm-3 . Devices with an emitter size of 4μm × 30μm have a current gain variation less than 2% across the fully processed 100mm wafer. ft and fmax are over 50GHz,with a power efficiency of 50% ,which are comparable to standard power GaAs HBT results. These results demonstrate the potential application of GaAsSb/InP DHBT for power amplifiers and the feasibility of multi-wafer MBE for mass production of GaAsSb-based HBTs.     

High-quality single-crystal CdSe nanoribbons and their optical properties

Large-scale synthesis of single-crystal CdSe nanoribbons is achieved by a modified thermal evaporation method, in which two-step-thermal-evaporation is used to control CdSe sources＇ evaporation. The synthesized CdSe nanoribbons are usually several micrometers in width, 50 nm in thickness, and tens to several hundred micrometers in length. Studies have shown that high-quality CdSe nanoribbons with regular shapes can be obtained by this method. Room-temperature photolumines-cence indicates that the lasing emission at 710 nm has been observed under optical pumping （266 nm） at power densities of 25-153 kW/cm^2. The full width half maximum （FWHM） of the lasing mode is 0.67 nm