外腔式KTP光学参量振荡器的实验研究

利用脉冲氙灯抽运的Nd：YAG被动调Q激光器输出的1．06μm激光脉冲泵浦KTP光学参量振荡器,获得脉宽3ns、单脉冲能量30mJ、中心波长1568nm的信号光输出。信号光脉冲宽度（3ns）比抽运光脉冲宽度（12ns）4,得多。实验表明,随着OPO腔长的增加单脉冲输出能量减小,随着抽运光能晕的增加单脉冲输出．能晕增大,...     

LD抽运的Nd∶YLF /Cr4 + ∶YAG被动调Q激光器

报道了激光二极管(LD ) 抽运的Nd ∶YLF 激光器, 采用平凹腔结构, 分别用两片 Cr4 + ∶YAG可饱和吸收晶体,实现了被动调Q,输出激光波长为1053nm。采用厚度为0. 5mm小信号透过率为90%的Cr4 + ∶YAG,在泵浦功率最大为17W时,输出脉冲宽度为60. 6ns,平均功率为1. 5W,重复频率为9. 5kHz,单脉冲能量为157. 9mJ;采用厚度为0. 55mm小信号透过率为95%的Cr4 + ∶YAG,在泵浦功率最大为17W时,输出脉冲宽度为68. 6ns,平均功率为1. 35W,重复频率为14kHz,单脉冲能量为96. 4mJ。     

1 110 nm Nd:GGG 激光器与555 nm 倍频激光器

采用紧凑的直腔设计和精确的膜系设计, 实现了LD 侧面泵浦1 110 nm Nd:GGG 和腔内倍频的555 nm 激光.当泵浦功率为168 W时, 得到了25.5 W的1110 nm 连续激光输出.在10 kHz 的声光调Q 情况下, 应用II 类非临界相位匹配LiB3O5(LBO)倍频晶体, 得到了最大输出功率为3.1 W的555 nm 倍频光输出, 光-光转换效率为1.8 %, 相应的脉冲宽度为176 ns, 在水平和竖直方向上的M2因子分别为19.6 和21.3.     

信号光脉冲比抽运光窄12倍的内腔式KTP光参量振荡器

在闪光灯抽运的非稳腔Nd∶YAG被动调Q激光器腔内,放置非临界相位匹配KTP晶体,构成内腔式单谐振KTP光参量振荡器(OPO)。研究了输出信号光的波长调谐性能,获得1.57~1.60μm可调谐激光脉冲。实验结果表明,1.57μm信号光的输出能量随着光参量振荡器腔长的增加而减少,脉冲宽度随着腔长的增加而有所变化;抽运能量较大时,转换效率随着抽运能量的增加趋于饱和然后逐渐下降;对此给予了合理的理论解释。当光参量振荡器的腔长为5 cm,1.06μm抽运光脉冲宽度为30 ns时,输出的1.57μm信号光的脉冲宽度为2.5 ns,能量为21.3 mJ。1.57μm信号光的脉冲宽度仅为1.06μm抽运光脉冲的1/12,总的电光能量转换效率为0.128%。     

基于ZnGeP2光参量振荡器的长波红外双波段调谐实验研究

文中报道了一种基于ZnGeP₂ (ZGP) 的纳秒宽调谐长波红外光参量振荡器(optical parametric oscillation, OPO)。采用重复频率50 Hz、脉冲宽度小于10 ns的1064 nm基频光泵浦基于Ⅱ类相位匹配KTP的光参量振荡器产生2.1 μm激光,进而泵浦基于Ⅰ类相位匹配的ZGP光参量振荡器产生7~11 μm长波红外输出。通过对ZGP的角度调谐获得了2.815~2.963 μm连续可调谐信号光,对应闲频光波长连续可调谐范围为7.82~9.08 μm。通过泵浦波长调谐的方式,当采用2107.13~2153.95 nm范围内的激光泵浦ZGP-OPO,获得了信号光波长范围为2.624~2.662 μm和2.745~2.956 μm的连续可调谐输出,对应闲频光范围为7.94~9.07 μm和10.20~10.82 μm。闲频光波长为8.03 μm、能量为0.8 mJ时,ZGP-OPO的泵浦光至闲频光转换效率9.4%。     

LDA侧面泵浦1319nm/1338nm双波长激光器的研究

使用最大泵浦功率为600 W的LDA侧面泵浦组件,并采用布儒斯特偏振片以及同时优化全反镜和输出镜透过率两种方法,获得了功率基本相等的1319 nm/1338 nm双波长激光输出。在连续输出时,获得30 W的输出功率,利用声-光Q开关调Q输出,在重复频率为4 kHz时,单脉冲能量为6 mJ,脉冲宽度为237 ns,峰值功率为25 kW。     

内腔式KTP光学参量振荡器的实验研究

在脉冲氙灯抽运的Nd∶YAG被动调Q激光器腔内,插入非临界相位匹配KTP晶体,构成内腔式KTP光学参量振荡器,获得脉宽3 ns、单脉冲能量10 mJ、中心波长1.568μm的人眼安全激光输出。当光学参量振荡器的腔长分别为3 cm,6 cm和8 cm时,得到的信号光脉冲的时间宽度分别为6 ns,4 ns和3 ns。当氙灯电注入能量为26 J时,输出的信号光出现双脉冲。实验上比较了Nd∶YAG激光器不同的谐振腔结构和参量对信号光脉冲的影响,并从理论上加以解释。     

LD抽运的Nd:YLF/Cr4+:YAG被动调Q激光器

报道了激光二极管（LD）抽运的Nd：YLF激光器，采用平凹腔结构，分别用两片Cr^4＋：YAG可饱和吸收晶体，实现了被动调Q，输出激光波长为1053nm。采用厚度为0．5mm小信号透过率为90％的Cr^4＋ YAG，在泵浦功率最大为17W时，输出脉冲宽度为60．6ns，平均功率为1．5W，重复频率为9．5kHz，单脉冲能量为157．9mJ；采用厚度为0．55mm小信号透过率为95％的Cr^4＋ YAG，在泵浦功率最大为17W时，输出脉冲宽度为68．6ns，平均功率为1．35W，重复频率为14kHz，单脉冲能量为96．4mJ。     

内腔泵浦的BaWO4反斯托克斯拉曼激光器实验研究

实验研究了内腔BaWO4反斯托克斯拉曼激光器的激光特性。通过在调Q的基频谐振腔中插入一倾斜的BaWO4拉曼谐振腔,实现基频光、一阶斯托克斯光和一阶反斯托克斯光的非共线相位匹配,进而实现了内腔反斯托克斯拉曼激光器在968nm的运转。测量了不同泵浦电压下输出的一阶反斯托克斯光的单脉冲能量,当泵浦电压为750V时,获得的最大输出能量为0.79mJ,相应的基频光到一阶反斯托克斯光的转化效率为1.5%。一阶反斯托克斯光的典型脉冲宽度为4.9ns。     

高效双端泵电光腔倒空Nd：YLF1053nm激光器

采用150 W光纤泵浦模块双向端面泵浦Nd：YLF晶体,使用Zemax光学设计软件,设计了使泵浦光成像比例为1.0∶1.5的4片式耦合光学系统,并利用高速RTP晶体电光腔倒空技术,得到了短脉宽、高稳定性和高光束质量的1 053 nm激光输出。当重复频率为1 Hz、注入能量为32 mJ时,输出脉冲宽度为2.5 ns、能量...     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Nanoimprint Lithography -A Next Generation High Volume Lithography Technique

IntroductionNanoimprint Lithography is a well-acknowl-edged low cost, high resolution, large area pattern-ing process. It includes the most promising methods,high-pressure hot embossing lithography (HEL) [2],UV-cured imprinting (UV-NIL) [3] and micro contactprinting (m-CP, MCP) [4]. Curing of the imprintedstructures is either done by subsequent UV-lightexposure in the case of UV-NIL or by cooling downbelow the glass transition temperature of the ther-moplastic material in case of HEL…     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

Influence of PVK ： NPB hole transporting layer on the characteristics of organic light-emitting devices

A doping system consisting of NPB and PVK is employed as a composite hole transporting layer （CHTL）. By adjusting the component ratio of the doping system, a series of devices with different concentration proportion of PVK ： NPB are constracted. The result shows that doping concentration of NPB enhances the competence of hole transporting ability, and modifies the recombination region of charge as well as affects the surface morphology of doped film. Optimum device with a maximum brightness of 7852 cd/m^2 and a power efficiency of 1.75 lm/W has been obtained by choosing a concentration proportion of PVK ： NPB at 1：3.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.     

Analysis of error performance on Turbo coded FDPIM

Due to variable symbol length of digital pulse interval modulation（DPIM）, it is difficult to analyze the error performances of Turbo coded DPIM. To solve this problem, a fixed-length digital pulse interval modulation（FDPIM） method is provided. The FDPIM modulation structure is introduced. The packet error rates of uncoded FDPIM are analyzed and compared with that of DPIM. Bit error rates of Turbo coded FDPIM are simulated based on three kinds of analytical models under weak turbulence channel. The results show that packet error rate of uncoded FDPIM is inferior to that of uncoded DPIM. However, FDPIM is easy to be implemented and easy to be combined, with Turbo code for soft-decision because of its fixed length. Besides, the introduction of Turbo code in this modulation can decrease the average power about 10 dBm, which means that it can improve the error performance of the system effectively.     

A method for calculating the center position of collimated light

It is a key problem to accurately calculate beam spots＇ center of measuring the warp by using a collimated laser. A new method, named double geometrical center method （DGCM）, is put forward for the first time. In this method, a plane wave perpendicularly irradiates an aperture stop, and a charge couple device （CCD） is employed to receive the diffraction-beam spots, then the geometrical centers of the fast and the second diffraction-beam spots are calculated respectively, and their mean value is regarded as the center of datum beam. In face of such adverse instances as laser intension distributing defectively, part of the image being saturated, this method can still work well. What＇s more, this method can detect whether an unacceptable error exits in the courses of image receiving, processing and calculating. The experimental results indicate the precision of this method is high.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.