1V高线性度2.4GHz CMOS低噪声放大器

讨论了低噪声放大器(LNA)在低电压、低功耗条件下的噪声优化及线性度提高技术.使用Chartered 0.25μm RF CMOS 工艺设计一个低电压折叠式共源共栅LNA.后仿真结果表明在1V电源下,2.36GHz处的噪声系数NF仅有1.32dB,正向增益S21为14.27dB,反射参数S11、S12、S22分别为 -20.65dB、-30.27dB、-24dB,1dB压缩点为-13.0dBm,三阶交调点IIP3为-0.06dBm,消耗的电流为8.19mA.     

2.45 GHz 0.18 μm全差分CMOS低噪声放大器设计

设计了一个基于TSMC 0.18 μm CMOS工艺的2.45 GHz全差分CMOS低噪声放大器.根据电路结构特点,采用图解法对LNA进行功耗约束下的噪声优化,以选取最优的晶体管栅宽;设计了仅消耗15 μA电流的偏置电路;采用在输入级增加电容的方法,在改善输入匹配网络特性的同时,解决了栅极电感的集成问题.仿真结果表明:LNA噪声系数为1.96 dB,功率增益S_(21)超过20 dB,输入反射系数S_(11)和输出反射系数S_(22)分别小于-30 dB和-20 dB,反向功率增益S_(12)小于-30 dB,1 dB压缩点和三阶互调输入点IIP3分别达到-17.1 dBm和-2.55 dBm,整个电路在1.8 V电源下功耗为22.4 mW.     

0.6V CMOS低噪声放大器的设计与优化*

采用SMIC 0.18 μm CMOS工艺设计了一个低电压低功耗的低噪声放大器(Locked Nucleic Acid,LNA).分析了在低电压条件下LNA的线性度提高及噪声优化技术.使用Cadence SpectreRF仿真表明,在2.4 GHz的工作频率下,功率增益为19.65 dB,输入回波损耗S11为-12.18 dB,噪声系数NF为1.2 dB,1 dB压缩点为-17.99 dBm,在0.6V的供电电压下,电路的静态功耗为2.7 mW,表明所设计的LNA在低电压低功耗的条件下具有良好的综合性能.     

一种低功耗K频段低噪声放大器

基于0.13μm锗硅(SiGe)双极型互补金属氧化物(Bipolar Complementary Metal Oxide Semi-conductor,BiCMOS)工艺,设计制作了一种高增益低功耗K频段低噪声放大器(Low Noise Amplifier,LNA),通过优化晶体管尺寸及利用硅通孔设计高品质因数射极退化电感,降低了LNA噪声.实测结果表明,在1.6 V偏置条件下,该LNA在20 GHz的噪声系数等于1.94 dB,输入1 dB压缩点等于-29.6 dBm;18～21.3 GHz频率范围内,LNA增益大于23.3 dB,S11和S22均小于-10 dB.包含偏置电路功耗在内,芯片功耗仅21 mW,优于其他同等噪声系数的K频段SiGe BiCMOS LNA.该LNA可应用于卫星通信等K频段低功耗接收机系统.     

1.5-6GHz增益和噪声系数稳定的两级超宽带CMOS低噪声放大器设计与性能模拟

 针对UWB应用设计实现了一个1.5-6GHz的两级CMOS低噪声放大器(LNA). 通过引入共栅(CG)和共源(CS)结构以获得宽范围内的输入匹配,采用电流镜和峰化电感进行电流复用,所提出的LNA实现了非常平坦化的功率增益和噪声系数(NF). 经标准0.18μm CMOS工艺实现后,版图后模拟结果表明在1.5-5GHz频率范围内功率增益(S21)为11.45±0.05dB,在2-6GHz频率范围内噪声系数(NF)为5.15±0.05dB,输入损耗(S11)小于-18dB. 在5GHz时,模拟得到的三阶交调点(IIP3)为-7dBm,1dB压缩点为-5dBm.在1.8V电源电压下,LNA消耗6mA的电流,版图实现面积仅为0.62mm^2.     

多模式卫星导航接收机中双频段LNA设计

设计出一款应用于多模式卫星导航接收机射频前端的双波段LNA,该电路可以工作在1.575GHz和1.267GHz两个波段附近,覆盖了当今各种卫星导航系统的载波频段.LNA的输入阻抗和输出阻抗均被匹配到50Ω,电路采用0.18μmCMOS工艺实现.测试结果表明该电路在1.575GHz和1.267GHz两个波段上噪声系数分别为0.88dB和0.78dB,功率增益分别为25.5dB和25.9dB,S11分别为-16dB和-12.5dB,1dB压缩点分别为-23.4dBm和-23.6dBm,1.8V供电电压条件下静态工作电流均为4.0mA.电路在上述两个频段上稳定性均满足要求.     

低功耗CMOS射频低噪声放大器的设计

介绍了一个针对无线通讯应用的2.1 GHz低噪声放大器(LNA)的设计.该电路采用Chartered 0.25 μm CMOS工艺,电源电压为2.5 V,设计中使用了多个电感,详述了设计过程并给出了优化仿真结果. 模拟结果显示,该电路能提供21.63 dB的正向增益(S21),功耗为12.5 mW,噪声系数为2.1 dB,1 dB压缩点为-19.054 1 dBm.芯片面积为0.8 mm×0.6 mm.测试结果达到了设计指标,一致性良好.     

一种用于超宽带接收机的CMOS可变增益低噪声放大器

本文介绍一种符合中国超宽带应用标准的工作频率范围为4.2-4.8 GHz的CMOS可变增益低噪声放大器(LNA)。文章主要描述了LNA宽带输入匹配的设计方法和低噪声性能的实现方式,提出一种3位可编程增益控制电路实现可变增益控制。该设计采用0.13-μm RF CMOS工艺流片,带有ESD引脚的芯片总面积为0.9平方毫米。使用1.2 V直流供电,芯片共消耗18 mA电流。测试结果表明,LNA最小噪声系数为2.3 dB,S(1,1)小于-9 dB,S(2,2)小于-10 dB。最大和最小功率增益分别为28.5 dB和16 dB,共设有4档可变增益,每档幅度为4 dB。同时,输入1 dB压缩点是-10 dBm,输入三阶交调为-2 dBm。     

一个950MHz CMOS低噪声放大器的设计

介绍了一个采用0.18μm 1.8V RF CMOS工艺,适合GSM接收器,中心频率为950MHz的低噪声放大器(LNA)的设计过程,并给出了spectreRF的模拟结果.在935～960MHz频带内,LNA功率增益大于16dB,阻抗匹配系数S11小于-18dB,噪声系数(NF)小于2.7dB,IIP3为-3.06dBm,ldB压缩点为-10.955dBm,功耗小于20mW.     

一种多模多频无线收发器前端SiGe BiCMOS低噪声放大器

基于IBM 0.18μm SiGe BiCMOS工艺,提出了一种应用于2.4～2.5GHz 802.11b/g频段的低噪声放大器(LNA).电路采用全差分发射极电感负反馈共射共基(Cascode)结构,对称电感有效地降低了芯片面积,优化了电路性能.仿真结果表明:该电路在2.4 GHz到2.5 GHz频率范围内,增益(S21)达到25 dB,噪声系数(NF)小于1.5 dB,大幅度提高了收发机系统的性能.此外,输入和输出匹配(S11,S22)分别达到-15 dB,1 dB压缩点大于-25 dBm.电源电压为2.5 V时电路总电流为3 mA.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.