基于混沌压缩感知的稀疏时变信号在线估计

混沌压缩感知是一种利用混沌系统实现非线性测量的压缩感知理论。针对稀疏时变信号的混沌压缩感知,该文提出稀疏时变信号的在线估计架构,构建一种递归最小二乘准则下的稀疏约束目标函数;通过利用迭代加权非线性最小二乘算法求解目标函数最小化问题,实现稀疏时变信号的参数估计。以Henon混沌系统为例仿真分析了频域时变稀疏信号的估计性能,数值模拟证明了该方法的有效性。     

混沌模拟信息转换——基于多射法的稀疏信号重构

混沌压缩采样是应用混沌系统实现非线性测量的压缩采样理论。该文研究模拟信号的混沌压缩采样-混沌模拟信息转换。该转换通过稀疏信号激励混沌系统,低速采样系统输出实现;信号重构则以混沌系统参数估计理论为基础,通过稀疏正则化的非线性最小二乘问题进行求解。该文将多射法(MS)与迭代再加权非线性最小二乘算法(IRNLS)结合,给出混沌模拟信息转换的MS-IRNLS信号重构算法。文中以Lorenz系统为例,仿真验证了MS-IRNLS算法的重构性能,结果表明方法的有效性。     

基于Monte Carlo采样的压缩感知弱匹配去噪重构

最小二乘是现有贪婪迭代类压缩感知重构算法中通用的信号估计方法,其未考虑到可能将量测噪声引入信号估计的情况.针对以上不足,提出一种基于Monte Carlo采样的压缩感知弱匹配去噪重构算法.该算法在未知信号稀疏度先验的条件下,通过引入递推Bayesian估计减小量测噪声的干扰;同时,以弱匹配的方式筛选出有效的原子,并剔除冗余原子进而重构原信号.新算法继承了现有贪婪迭代类算法的有效性,同时避免了因噪声干扰或稀疏度未知导致的重构失败.理论分析和实验表明,新算法在同等条件,尤其是非高斯噪声情况下,重构性能优于现有典型贪婪迭代类算法,且其运算时间低于BPDN算法和同类的KF-SAMP算法.     

基于子空间的块稀疏信号压缩感知重构算法

块稀疏信号是一种典型的具有特殊结构的稀疏信号,在压缩感知问题中,针对块稀疏信号的特点,提出了一种基于子空间的块稀疏信号压缩感知重构算法.该算法每次迭代找到整个信号支撑块的估计,包含正确信号支撑块所在空间的一个子空间,然后计算残差,并在下一次迭代时,通过回溯思想和最小均方准则修正更新上一次找到的信号支撑块,最后直到残差为...     

基于卡尔曼滤波的压缩感知弱匹配去噪重构

现有的贪婪迭代类压缩感知重构算法均基于最小二乘对信号进行波形估计,未考虑到可能将量测噪声引入信号估计的情况.针对以上不足,提出了一种基于线性Kalman滤波的压缩感知弱匹配去噪重构算法.该算法不需已知稀疏度先验,通过引入Kalman滤波,在最小均方误差准则下,每次迭代都获得最佳信号估计;并以弱匹配的方式同时筛选出有效的原子,并剔除冗余原子进而重构原信号.新算法继承了现有贪婪迭代类算法的有效性,同时避免了因噪声干扰或稀疏度未知导致的重构失败.理论分析和实验表明,新算法在同等条件下,重构性能优于现有典型贪婪迭代类算法,且其运算时间低于BPDN算法和同类的KFCS算法.     

压缩感知中一种改进的迭代硬阈值算法

研究了压缩感知理论中一种改进的迭代硬阈值稀疏信号重构算法。针对现有IHT算法类最优秀的BIHT算法中回溯操作无法保证稀疏信号重构误差递减的问题,对稀疏重构误差及其差值进行了简单介绍和分析,提出了一种能够保证重构误差随迭代进行单调减小的重构算法,在每次迭代的回溯操作中选择能够保证重构误差逐渐减小的原子,并将其指标与估计支撑集合并,最后基于最小二乘法进行伪逆运算获取稀疏信号估计。对高斯稀疏信号和0-1稀疏信号进行了仿真,证明了优于IHT、NIHT以及BIHT算法的稀疏信号重构性能。     

基于非局部相似性和交替迭代优化算法的图像压缩感知

压缩感知理论突破了信号带宽对奈奎斯特采样定理的限制,并且实现了在数据采样的同时进行压缩。目前压缩感知系统通常利用图像在某个变换域具有稀疏性的先验知识,从少量观测值中重构原始图像。本文利用图像像素的邻域结构信息及图像子块的相似性,将图像的非局部相似性作为先验知识运用到压缩感知图像重构中。结合图像的非局部相似性及其在变换域的稀疏性先验知识,提出了基于非局部相似性和交替迭代优化算法的图像压缩感知重构算法,该算法利用迭代阈值法和非局部全变差来交替迭代求解变换域的稀疏性优化问题和非局部相似性的优化问题。实验结果表明,本文算法可以有效提高图像重构的视觉效果和峰值信噪比。      

基于压缩感知的信号重构研究

按照Nyquist采样定理,信号的采样率必须为信号最高频率的2倍以上,这会产生大量的冗余数据。压缩感知是一种新兴的采样理论,对于可以稀疏表示的信号,它能够以远低于Nyquist采样速率对信号进行采样,并通过优化算法实现重构。介绍了压缩感知的基本理论,并分别选取时域稀疏、频域稀疏和图像信号进行了仿真分析,实验结果显示,压缩感知理论能较好的重构原始信号。     

DPSS基下多带流信号的恢复

压缩感知技术是近年来信号处理领域最热门的技术。传统的压缩感知理论并未考虑到稀疏信号本身可能具有的某种结构,块稀疏就是其中的一种。本文针对压缩感知的多带块稀疏流信号,将稀疏信号重构算法与调制的DPSS（Discrete Prolate Spheroidal Sequence ）基扩展相结合,建立了多带块稀疏模型,并利用压缩感知AIC结构,在远低于奈奎斯特速率下对多带宽模拟信号进行采样。结合压缩感知获得的观测方程和利用前后窗内信号的相关性建立的信号状态转移方程,采用降阶的卡尔曼滤波算法恢复原始信号。相对于傅里叶基扩展,DPSS基扩展在降低采样结构复杂度的同时,克服了频谱泄露的问题。仿真结果表明,多带信号在DPSS基下的恢复性能优于多带信号在FFT基下的重构。      

面向压缩感知的块稀疏度自适应迭代算法

块稀疏信号是一种典型的稀疏信号,目前在块稀疏信号的压缩感知问题中,大多数信号重构算法要求信号的块稀疏度已知且算法复杂度高.针对实际应用中信号块稀疏度未知的情况,提出了一种块稀疏度自适应迭代算法,用于信号重构.首先,该算法初始化一个块稀疏度,其值按设定步长进行增加.对每一个块稀疏度的迭代,算法都会找到信号支撑块的一个子集,并修正更新上一次找到的信号支撵块,最后找到信号的整个支撑块,从而重构出源信号.该算法不需要信号的块稀疏度作为先验知识,而且算法复杂度低.仿真实验表明,该算法的重构概率较已有大多数块稀疏信号重构算法的重构概率高,在块稀疏信号的压缩感知问题中具有实际意义.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Nanoimprint Lithography -A Next Generation High Volume Lithography Technique

IntroductionNanoimprint Lithography is a well-acknowl-edged low cost, high resolution, large area pattern-ing process. It includes the most promising methods,high-pressure hot embossing lithography (HEL) [2],UV-cured imprinting (UV-NIL) [3] and micro contactprinting (m-CP, MCP) [4]. Curing of the imprintedstructures is either done by subsequent UV-lightexposure in the case of UV-NIL or by cooling downbelow the glass transition temperature of the ther-moplastic material in case of HEL…     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

Influence of PVK ： NPB hole transporting layer on the characteristics of organic light-emitting devices

A doping system consisting of NPB and PVK is employed as a composite hole transporting layer （CHTL）. By adjusting the component ratio of the doping system, a series of devices with different concentration proportion of PVK ： NPB are constracted. The result shows that doping concentration of NPB enhances the competence of hole transporting ability, and modifies the recombination region of charge as well as affects the surface morphology of doped film. Optimum device with a maximum brightness of 7852 cd/m^2 and a power efficiency of 1.75 lm/W has been obtained by choosing a concentration proportion of PVK ： NPB at 1：3.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.     

Analysis of error performance on Turbo coded FDPIM

Due to variable symbol length of digital pulse interval modulation（DPIM）, it is difficult to analyze the error performances of Turbo coded DPIM. To solve this problem, a fixed-length digital pulse interval modulation（FDPIM） method is provided. The FDPIM modulation structure is introduced. The packet error rates of uncoded FDPIM are analyzed and compared with that of DPIM. Bit error rates of Turbo coded FDPIM are simulated based on three kinds of analytical models under weak turbulence channel. The results show that packet error rate of uncoded FDPIM is inferior to that of uncoded DPIM. However, FDPIM is easy to be implemented and easy to be combined, with Turbo code for soft-decision because of its fixed length. Besides, the introduction of Turbo code in this modulation can decrease the average power about 10 dBm, which means that it can improve the error performance of the system effectively.     

A method for calculating the center position of collimated light

It is a key problem to accurately calculate beam spots＇ center of measuring the warp by using a collimated laser. A new method, named double geometrical center method （DGCM）, is put forward for the first time. In this method, a plane wave perpendicularly irradiates an aperture stop, and a charge couple device （CCD） is employed to receive the diffraction-beam spots, then the geometrical centers of the fast and the second diffraction-beam spots are calculated respectively, and their mean value is regarded as the center of datum beam. In face of such adverse instances as laser intension distributing defectively, part of the image being saturated, this method can still work well. What＇s more, this method can detect whether an unacceptable error exits in the courses of image receiving, processing and calculating. The experimental results indicate the precision of this method is high.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.