非理想SIC下全双工NOMA系统的安全性能分析

针对存在多个非共谋窃听者,研究了一种基于全双工中继和两阶段中继选择（TSRS）的非正交多址接入（NOMA）物理层安全通信方案。每个通信过程包含一个传输时隙,系统在每个时隙开始由TSRS策略选择最优中继,所选中继在从源节点接收NOMA叠加信号的同时,向两个目的节点转发上一时隙的再编码叠加信号,两个目的节点采用串行干扰消除（SIC）技术从中继叠加信号中解码获取各自的期望信号。推导了非理想SIC下系统安全中断概率的近似表达式,进行了蒙特卡洛（Monte-Carlo）仿真验证,同时分析了各仿真参数（SIC残余干扰系数、目标安全速率、中继规模等）与系统安全中断概率的关系。理论分析与模拟仿真的结果表明,全双工技术与TSRS的结合方案能有效提升系统的安全中断性能。将该方案应用于实际通信系统设计时,选择合适传输信噪比（SNR）、提高串行干扰消除能力或适当增加中继数量均可实现更好的保密性能。      

面向蜂窝网络的D2D多播通信的分簇和中继选择方法

传统蜂窝网络中,信道衰减的随机性和不确定性导致小区边缘用户的接收性能很差,尤其是面向视频传输等速率要求较高时其弊端更加凸显。D2D通信因其配置灵活性可作为传统蜂窝网络架构的有利补充,能有效改善边缘用户的性能。该文针对D2D通信的多播传输,分析了系统最小时延成本下的中继数量和分簇算法,提出一种基于分簇和中继选择的低时延D2D多播方案。该方案可以自适应选择多播重传中的中继的数量和中继节点到基站的距离,同时给出最优的带宽资源分配机制。仿真结果表明,与其他方案相比,所提方法能有效减少系统时延,提高边缘用户体验和系统性能。     

过时CSI下全双工中继辅助D2D网络的物理层安全

中继辅助终端直通（devicetodevice,D2D）网络通过与蜂窝网络共享频谱提高D2D用户的频谱效率和蜂窝用户（cellular user,CU）的物理层安全性。为进一步改善其性能,可以在基站和D2D链路的中继节点采用天线选择以及在中继节点采用全双工技术。然而,由于存在反馈时延和移动性,用于蜂窝链路和所有D2D链路天线选择的信道状态信息（channelstateinformation,CSI）均可能是过时的,针对该场景下的物理层安全性和可靠性问题,提出一种主动窃听和过时CSI场景下基站和中继节点均采用发射天线选择的全双工中继辅助D2D网络安全模型,推导CU的中断概率、遍历容量、非零安全容量概率、安全中断概率、渐近安全中断概率的解析表达式。数值计算与仿真结果均表明,基站发射天线数、中继干扰天线数越多,CU的安全性能越好;过时的CSI会降低CU的中断性能和安全性能。     

基于安全中断概率的D2D安全接入策略

针对D2D蜂窝系统通信安全性受资源限制的问题,考虑到蜂窝链路和D2D链路的同频干扰能够为两者带来安全增益,基于此,提出一种基于安全中断概率的D2D用户接入策略。首先理论分析了蜂窝用户和D2D用户的安全中断概率,并给出了基于安全中断概率最小化的D2D用户功率优化算法。在上述分析的基础上,选择安全中断概率最小的D2D用户接入复用蜂窝用户的无线资源,同时提高D2D通信链路和蜂窝上行链路的安全性。最后,仿真结果证明了所提算法的有效性。     

D2D中继网络负载均衡的中继选择算法

主要研究D2D(终端直通)系统与蜂窝网络共存时,D2D到基站的中继选择问题。引入考虑路径损耗及衰落的系统架构,导出选择D2D中继的距离范围。在此基础上对两种基本中继选择算法的中断概率进行推导和分析。提出负载转移的最优中继选择算法,旨在降低中继选择时的中断概率,提高系统整体性能。仿真结果说明提出的LTBRS(负载转移最优中继选择)算法比传统的最优中继选择和随机中继选择性能更优。     

D2D系统中带QoS约束的多天线选择及性能分析

本文研究了蜂窝直通通信（Device-to-Device,D2D）系统中基站端多天线选择问题,即在基站传输过程中选择多于一根天线进行传输。借助于次序统计的相关结论,本文分析了该D2D系统的整体性能。本文首先针对基站内的激活用户和D2D用户分别推导了概率密度函数和累积密度函数,进而得到了D2D系统的整体中断概率。基于推导结果,本文提出了一种基于服务质量（Quality of Service,QoS）约束的多天线选择方案来进一步提高基站端的能效,其中所需的天线数根据QoS约束和发送信噪比来确定。论文最后通过仿真验证了所做推导的正确性,以及展示了本文所提方案相对于最优天线选择的优势。      

两阶段中继选择策略下SWIPT-CR-NOMA网络的中断性能分析

针对采用无线携能传输(SWIPT)的多中继协作底层认知NOMA网络,提出一种基于NOMA和串行干扰消除协议的两阶段中继选择策略(TSRS),次级网络源节点和所选中继采用相同的功率分配生成多用户叠加信号,中继只利用采集能量提供解码转发服务。推导了用户中断概率的闭合表达式,进行了蒙特卡洛仿真验证,分析了功率分配因子、能量分裂参数、干扰温度限和中继数量等系统参数对中断性能的影响。仿真结果表明,所提方案可显著提升协作系统中断性能。      

两级中继选择的协作CR-NOMA网络性能分析

本文研究了中继选择方案对协作下认知非正交多址（CR-NOMA）网络中断性能的影响,提出了一种两级中继选择方案。第一时隙在保证主用户服务质量的基础上,次级网络源节点向认知中继集群广播叠加信号。第二时隙认知中继提供解码转发服务,协助源节点传输信息。基于上述假设,推导了次级用户中断概率的闭合表达式并给出了分析结果。证明相比于部分中继选择策略,两级中继选择策略可以达到更好的中断性能和更大的分集增益。同时本文的分析结果验证了备选中继节点数目和功率分配因子对系统中断性能的影响,蒙特卡罗仿真验证了理论结果。      

基于用户中断概率的D2D通信干扰协调与资源分配

在LTE系统中引入设备直传(D2D)通信技术,会因为D2D用户复用蜂窝用户资源进行通信而产生同频干扰.在现有的干扰协调与资源分配研究中,都需要基站获取各个通信链路的信道状态信息(CSI),但这样无疑会增加基站的信令负担.为减小干扰与基站的信令负担,提出了一种基于用户中断概率的干扰协调与资源分配算法,首先在保证蜂窝用户正常通信的情况下,通过限制D2D用户到基站间的距离来降低干扰;其次通过遍历所有蜂窝用户的频谱资源,选择能使D2D用户的总中断概率最低的频谱资源进行复用.仿真结果表明,所提算法能够在保证蜂窝用户正常通信的情况下,明显降低D2D用户的平均中断概率,同时还能够降低基站信令负担.     

NOMA-D2D协作无线系统的物理层安全

针对未来海量用户设备接入的物理层安全（physical layer security，PLS）应用需求，提出了一种组合非正交多址接入（non-orthogonal multiple access，NOMA）、终端直通（device-to-device，D2D）与中继协作的NOMA-D2D协作无线系统PLS模型。该模型由采用发射天线选择（transmit antenna selection，TAS）的基站、分别作为基站和D2D发射端的NOMA远端蜂窝用户、D2D接收端以及被动窃听者组成，其中的D2D发射端承担基站的 NOMA 近端用户和解码转发中继两种角色。利用高斯—切比雪夫正交定理推导两种 TAS 方案下NOMA-D2D协作无线系统的安全中断概率、非零安全容量概率以及渐近安全中断概率的近似表达式。数值计算和仿真实验验证了NOMA-D2D协作无线系统PLS性能分析的准确性；在基站总功率恒定时增大分配给远端蜂窝用户的功率能有效提升NOMA-D2D协作无线系统的PLS性能。     

放大转发中继网络中的一种中继选择方案

提出了一种放大转发网络中的中继选择方案,假设目的节点配置多个天线,源节点和所有中继节点都配置单个天线,方案选择一组中继同时在相同的频带上放大转发接收到的源节点信息以最大化接收信噪比。与只择一个最优中继的方案相比,方案在保持满分集阶数的情况下获得了更高的中断容量和更优的误符号率性能。与只选择一个最优中继的方案相比,在0.000 01的误符号率水平上,少需要发射功率1.6 dB。     

Asymptotic Analysis of Opportunistic Relaying Protocols

In this letter, we examine in detail a cooperative network with multiple relays. We investigate protocols that incorporate the opportunistic relaying technique, which selects the ?best? relay among the M available relays. We evaluate the asymptotic outage performance of incremental amplify-andforward (IAF) when it is extended to the opportunistic relaying scenario. Moreover, we propose two new protocols, namely opportunistic incremental selection AF and opportunistic joint incremental selection relaying, and derive the corresponding asymptotic outage probabilities. Finally, we compare the analytical asymptotic outage probabilities and the simulated ones. We conclude that the OJISR protocol outperforms the other protocols.     

基于部分中继选择的能量收集双跳网络信息年龄优化

针对传统中继协作网络传感器节点能量受限导致信息传输延迟较高的问题,将短包通信（SPC）和能量收集技术相结合,构建了一种双跳中继无线传感器网络模型。网络中源节点和中继均需从专用能量基站收集射频信号能量以保证信息的持续传输,中继采用半双工解码转发协议将源节点发送的状态更新信息以短包形式传递到目的节点,利用中继选择策略与最大比合并技术提出了基于时效性的最早部分中继选择方案。考虑该网络信息的新鲜度,首先,分析了SPC传输性能,推导了中继和目的节点处的平均包错误率。其次,利用顺序统计量描述了源节点到中继端数据包的重传次数,基于更新过程理论推导了网络的平均信息年龄（AoI）表达式,并采用梯度下降方法优化了影响网络平均AoI的部分参数。最后,仿真分析结果表明,优化中继数量和数据包长度可以有效提高网络信息新鲜度,同时,通过对比优化部分参数得到的最优值与贪婪方法得到的最小化平均AoI理论值,可以验证部分中继协作方案在双跳状态更新网络中的可行性。      

协作通信中的解码转发中继策略优化

在单中继协作通信系统模型下,研究了直接传输、固定解码转发（ DF）中继、选择DF中继和增量中继协议。为了提高协作通信系统的频谱效率和中断性能,通过比较源-目的端和中继-目的端的瞬时信道增益来判定是否需要采用协同通信模式,提出一种改进的解码转发方式（ IDF）。通过将选择DF中继和增量中继的优点结合,提出了一种增量选择中继（ ISR）策略,并给出了2种改进协议任意信噪比的中断概率表达式。仿真结果表明,与传统的单中继解码转发协议相比, IDF和ISR均具有更低的中断概率, ISR具有最低的中断概率。     

Capacity Maximization through Energy-Aware Multi-Mode Relaying

In future wireless mobile networks, data rate and quality of service are expected to be comparable to those of wired deployments. To achieve this target, novel architectures must be adopted, successfully countering the disadvantages of the wireless transmission. Inspired by that, cooperative relaying was proposed because of the various gains it introduces to the network. In this work we propose a scheme consisting of multi-mode decode and forward relays facilitating the communication between a base station and a user terminal (UT). By equipping the relays with two interfaces, we can exploit the plethora of the available wireless protocols. Also, instead of performing multi-relay transmissions, we adopt an opportunistic relaying scheme due to its simplicity and outage-optimality. Additionally, we incorporate successive transmissions to improve the spectral efficiency, thus recovering the half-duplex loss in capacity due to the two-hop transmission. However, as inter-relay interference arises from successive transmissions, we propose mitigation techniques through interference cancellation and out-band transmissions using the multi-mode relays. At the same time, an energy-aware mechanism is implemented in the selected relay’s transmission, opting for power reduction, as the channel state information is acquired prior to the signal’s forwarding to the UT. Finally, we give numerical results by comparing the proposed energy-aware multi-mode relaying (EA-MMR) scheme, with two other schemes in terms of average end-to-end capacity, outage probability, delay distribution and power gain.     

Cooperative spectrum sensing using amplify-and-forward relaying with partial relay selection in cognitive radio networks

Cooperative spectrum sensing has been shown to be an effective approach to improve the detection performance by exploiting the spatial diversity among multiple cognitive nodes. By using the amplify-and-forward relaying with partial relay selection, this paper proposes a novel cooperative spectrum sensing scheme, which provides higher detection performance and is interesting in distributed cognitive radio networks. In the proposed sensing scheme, the “best” cognitive relay by means of partial relay selection technique amplifies and forwards the signals transmitted from the primary user (PU) to the cognitive user (CU). Then the CU detects PU’s states (i.e., presence or absence) via an energy detector. Moreover, the average missed-detection probability of proposed sensing scheme is studied over Nakagami-m fading channels, where m is a positive integer. In particular, the tight closed-form lower bounds of the average missed-detection probability are presented for the convenience of performance evaluation in practice. Finally, numerical results are provided to validate the derived closed-form lower bounds and the influence of the number of cognitive relays on the detection performance is also discussed.     

D2D communications with subchannel reusing for throughput‐guaranteed relay selection in LTE

Using full‐duplex relaying in device‐to‐device (D2D) communication, spectrum efficiency can be further improved as compared with traditional half‐duplex relaying. Due to the increasing demands for more system capacities and higher data rate, a throughput‐guaranteed and power‐aware relay selection mechanism is essential so that services can be successfully accomplished within tolerable power consumption. It is also imperative to prevent cellular users from interfering and preserve resources for more users at the same time. In current paper, we proposed an efficient relay selection scheme with subchannel reusing. Using the nonconflict group discovery algorithm, firstly, we divided D2D pairs into different groups based on the neighbor lists of all the devices. The D2D pairs in the same group were considered nonconflictive. By building a matrix that represents the power consumption of D2D transmission peers through relays, we proposed a group‐oriented relay selection scheme based on the Hungarian method allowing subchannel reuse over relay‐assisted D2D networks. Applying this mechanism, different D2D pairs are able to transmit messages at the same subchannel, whenever they are in the same group. Better throughput and spectrum usage than currently available relay selection schemes without subchannel reusing can be obtained. Particularly, more D2D pairs in high dense networks can be accommodated, and spectrum resources can be better preserved. The simulation results showed that our proposed mechanism can improve the total throughput by up to 35% as compared with an existing relay selection scheme without subchannel reusing, called as PRS‐D2D, when most D2D pairs are in a few groups.