聚合氯化铝中纳米Al13形态的分离纯化及形态表征

采用超滤法和层析法分离纯化聚合氯化铝(PAC)中的Al₁₃形态,并采用Al-Ferron逐时络合比色法、²⁷Al-NMR、TEM和粒度测定仪对分离纯化所得的Al₁₃形态进行了分析和表征.研究结果表明,超滤法分离纯化的效果受超滤膜的孔径及PAC浓度的影响,选择合适孔径的膜和PAC溶液浓度即可以获得高纯度的Al₁₃,在层析法中则随着洗脱时间延长按分子的大小依次洗脱下来,因此截取中间组分即可得到Al₁₃;Al-Ferron逐时络合比色法和²⁷Al-NMR的分析结果表明,采用上述2种方法分离提纯得到的样品中Al₁₃的含量分别可达到90%以上和100%.TEM和粒度测定结果表明,在B=2.5的PAC溶液中,Al₁₃极少以Al₁₂AlO₄(OH)₂₄(H₂O)⁷⁺₁₂的单体形态存在,而是呈两维结构的线性和枝状的聚集体,Al₁₂AlO₄(OH)₂₄(H₂O)⁷⁺₁₂的聚集体尺寸通常在几十至几百nm.     

Al13形态在混凝中的作用机制

从铝的水解形态转化角度考察了铝盐在高碱度和高有机物浓度水体中的混凝行为.结果表明,铝盐的混凝效能是与混凝过程中的Al₁₃含量成正比.高投药量时氯化铝(AlCl₃)既可以有效调节水体pH值又能在混凝过程中原位水解产生较多的Al₁₃形态,因而混凝效能要高于聚合氯化铝(PACl).在铝盐混凝中,调节pH值到6～7之间可以控制铝形态分布从而达到提高混凝效能和减少残留铝的目的.在调节pH值强化混凝的方法中使用传统铝盐的效果要好于无机高分子絮凝剂.     

聚合氯化铝中纳米Al13电荷特性及其混凝效果

采用聚丙烯酰胺凝胶柱层析法分离纯化聚合氯化铝(PAC)中的Al₁₃形态,并采用Al-Ferron逐时络合比色法和ZATESIZER 3000HSA测定仪对分离所得纳米Al₁₃形态以及AlCl₃和PAC进行了分析表征和电荷特性的对比性研究;采用烧杯实验法对3个样品处理实际和模拟水样的混凝效果进行了对比性研究.Al-Ferron逐时络合比色法的结果表明,采用层析法分离可得到含量99%左右的纳米Al₁₃形态;电荷特性和混凝效果研究结果表明纳米Al₁₃形态较其它两者具有更好的除浊、除腐殖酸和脱色效果并且具有更强的电中和能力,因此Al₁₃形态是一种具有较高正电荷和较高的水解稳定性,在给水和废水处理中的一种较为有效的Al形态.     

Al13形态的凝胶层析分离及分离级分特性对比

采用聚丙烯酰胺凝胶柱层析法分离纯化聚合氯化铝(PAC)中的Al₁₃形态,并采用Al- Ferron逐时络合比色法、透射电镜(TEM)和ZATESIZER测定仪对分离纯化过程中所得3个级分进行了分析表征和电荷特性的研究;采用烧杯实验法对3个级分处理实际和模拟水样的混凝效果进行了对比性研究.Al- Ferron逐时络合比色法和TEM结果表明,在层析法分离中级分随着洗脱时间延长按分子的大小依次洗脱下来,因此截取中间组分即可得到含量95 %左右的纳米Al₁₃形态;电荷特性和混凝效果研究结果表明,第3个级分其他两者具有更好的除浊、除腐殖酸和脱色效果,并且具有更强的电中和能力,因此Al₁₃形态是一种具有较高正电荷和较高的水解稳定性以及宽的pH适用范围,在给水和废水处理中是一种较为有效的Al形态.     

富氧条件下SnO2/Al2O3催化剂上丙烯选择性还原NOx的研究

考察了分别用浸渍法、共沉淀法和溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂上丙烯选择性还原NO_x的催化活性,发现制备方法与Sn的负载量对其活性有重要影响.溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂活性最高,Sn的最佳负载量为5%.与浸渍法和共沉淀法制备的5%SnO₂/Al₂O₃催化剂相比,溶胶-凝胶法制备的5%SnO₂/Al₂O₃催化剂受水蒸汽的抑制作用较弱,并且在水和SO₂共存的条件下活性最高.此外,反应气中丙烯及氧气浓度的增加有利于NO_x转化率的提高.     

Preparation and characterization of Pd/Fe bimetallic nanoparticles immobilized on Al2O3/PVDF membrane: Parameter optimization and dechlorination of dichloroacetic acid

Using a liquid–solid phase inversion method, a hybrid matrix poly(vinylidene fluoride)(PVDF) membrane was prepared with alumina(Al2O3) nanoparticle addition. Pd/Fe nanoparticles(NPs) were successfully immobilized on the Al2O3/PVDF membrane, which was characterized by Scanning Electron Microscopy(SEM) and Transmission Electron Microscopy(TEM). The micrographs showed that the Pd/Fe NPs were dispersed homogeneously. Several important experimental parameters were optimized, including the mechanical properties, contact angle and surface area of Al2O3/PVDF composite membranes with different Al2O3 contents. At the same time, the ferrous ion concentration and the effect of hydrophilization were studied. The results showed that the modified Al2O3/PVDF membrane functioned well as a support. The Al2O3/PVDF membrane with immobilized Pd/Fe NPs exhibited high efficiency in terms of dichloroacetic acid(DCAA) dechlorination. Additionally, a reaction pathway for DCAA dechlorination by Pd/Fe NPs immobilized on the Al2O3/PVDF membrane system was proposed.     

Effects of Ce on catalytic combustion of methane over Pd-Pt/Al2O3 catalyst

Activity and stability of 1%Pd-0.2%Pt/Al₂O₃ and 1%Pd-0.2%Pt/0.6%Ce/Al₂O₃ catalysts prepared by impregnation method for catalytic combustion of methane in air were investigated. The catalysts before and after reaction were characterized by BET, CO chemisorption, XRD and XPS techniques. Results showed that the presence of Ce significantly increased the activity and thermal stability of the Pd-Pt/Al₂O₃ catalyst towards methane combustion, which could be attributed to more highly-dispersed active PdO particles over the Pd-Pt/Ce/Al₂O₃ catalyst surface as well as the retarded sintering of PdO and the maintained oxidized state of surface Pd during the combustion process in the presence of Ce.     

Pt/CeO2催化氧化甲苯反应机制研究

采用浸渍法制备了Pt/CeO_2和Pt/Al2O_3催化剂,并通过XRD、BET、ICP-OES、H2-TPR、XPS等手段表征其物理化学性质.结果发现,Pt/CeO_2和Pt/Al2O_3催化剂上Pt负载量约为0.6%,Al2O_3载体上Pt颗粒尺寸更小,Pt/CeO_2的可还原性更强.甲苯催化氧化活性评价结果表明,Pt/CeO_2催化剂表现出更好的催化活性,T50=170℃,T90=190℃.通过UV-Raman、甲苯TPD、GC/MS、In-situ FTIR等手段进一步研究发现,Pt/CeO_2活化甲苯及反应供氧的机制与Pt/Al2O_3存在区别,其活性更好是因为:(1)负载在CeO_2表面存在高电子密度的Pt原子,具有更强的活化甲苯能力,可以直接使苯基和甲基间的C—C链发生断裂;(2)Pt的负载促进了CeO_2氧空位形成,进一步提高了CeO_2的储氧性能,加速氧循环.除了Pt解离气相氧之外,CeO_2还可以提供活性氧物种参与催化氧化甲苯的反应,进一步提高甲苯催化氧化效率.     

Effect of pretreatment on Pd/Al2O3 catalyst for catalytic oxidation of o-xylene at low temperature

The effect of pretreatment on Pd/Al₂O₃ catalysts for the catalytic oxidation of o-xylene at low temperature was studied by changing the pretreatment and testing conditions. The fresh and pretreated Pd/Al₂O₃ catalysts were characterized by transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). The results showed that the pretreatment dramatically changed the Pd/PdO ratio and then significantly affected the Pd/Al₂O₃ activity; while the pretreatment had not much influence on Pd particle size. The Pd/Al₂O₃ pre-reduced at 300℃/400℃, which has fully reduced Pd species, showed the highest activity; while the fresh Pd/Al₂O₃, which has fully oxidized Pd species, presented the worst performance, indicating the Pd chemical state plays an important role in the catalytic activity for the o-xylene oxidation. It is concluded that metallic Pd is the active species on the Pd/Al₂O₃ catalyst for the catalytic oxidation of o-xylene at low temperature.     

聚合氯化铝与有机高分子复合絮凝剂的形态分布研究——AlFerron和~(27)AlNMR相结合

主要研究了Ａｌ－Ｆｅｒｒｏｎ逐时络合比色法和＾２７Ａｌ－ＮＭＲ法应用于聚合铝与有机高分子复合絮凝剂形态分布的测定，结果表明，两种方法分别测定的Ａｌｂ和Ａｌ１３的结果具有一定的相关性；聚合铝与有机高分子复合后其形态分布发生了一定的变化，Ａｌｂ（或Ａｌ１３）的含量有所降低，但仍是优势形态，Ａｌａ（或Ａｌ单）的含量基本保持不变。     

Cu-Al2O3中骨架铜类芬顿催化去除水中有机污染物

为解决传统铁基芬顿催化剂在水体通常酸碱(pH6)条件下活性低的问题,采用简单共沉淀法制备了Cu掺杂的Al_2O_3类芬顿催化剂.通过X射线衍射(XRD)、X射线光电子能谱(XPS)和紫外可见(UV-vis)吸收光谱分析表明,Cu-Al_2O_3中铜掺杂的质量分数低于4.77%时,催化剂中铜主要以Cu~(2+)和Cu~+的形式共存于Al_2O_3的骨架结构中,形成Al—O—Cu键;过量的铜掺杂会导致外骨架铜物种如铜氧化物团簇的存在.以难降解有机污染物2-氯苯酚(2-chlorophenol,2-CP)和染料罗丹明B(Rhodamine B,Rh B)为目标污染物,对Cu-Al_2O_3的类芬顿催化性能进行了详细地研究.结果表明,骨架铜物种在中性温和条件下对2-CP和Rh B显示出很高的催化去除效率和稳定性,反应2 h,Cu-Al_2O_3(Cu质量分数4.77%)对2-CP的去除率达到54%,相应的TOC去除率达到49%,而铜离子溶出浓度仅为0.025 5 mg·L-1,而Cu-Al_2O_3(Cu质量分数7.58%)由于外骨架铜的存在导致催化活性增加缓慢和稳定性下降.ESR测试结果表明,·OH和HO_2~-/O_2~-·是反应中主要的活性物种.     

Pd/CeZr/TiO2/Al2O3蜂窝状金属丝网催化剂选择催化还原NOX

采用溶胶-凝胶法和浸渍法制备了Pd/CeZr/TiO2Al2O3蜂窝状金属丝网催化剂,并将其应用于在富氧条件下以丙烯选择催化还原NOx的研究.利用扫描电镜(SEM)分析了钛酸四丁酯的含量以及涂敷次数对TiO2涂层的影响,系统地考察了Pd含量、氧气浓度和空速对蜂窝状金属丝网催化剂催化性能的影响.实验结果表明,采用钛酸四丁酯的含量为20.0%的溶胶,涂敷2次,可以在金属丝网载体上氧化铝涂层表面获得均匀、无皲裂的TiO2涂层;Pd含量在0.23%～1.06%的范围内, NOx的转化率随Pd含量的增加而减小, Pd含量为0.23%时, NOx表现最高的NOx转化率;反应气体中氧气浓度从1.5%增加到6.0%, NOx的转化率随氧气浓度的增加而增大,当氧气浓度高于6.0%, NOx的转化率则随氧气浓度的增加而迅速减小; NOx的转化率随着空速的增加而降低,在高温条件下空速对转化率的影响要大于在低温条件下.     

Enhanced photoelectrocatalytic degradation of ammonia by in situ photoelectrogenerated active chlorine on TiO2 nanotube electrodes

TiO_2 nanotube(Ti NT) electrodes anodized in fluorinated organic solutions were successfully prepared on Ti sheets. Field-emission scanning electron microscopy(FE-SEM) and X-ray diffraction(XRD) were performed to characterize the TiNT electrodes. The linear voltammetry results under irradiation showed that the TiNT electrode annealed at 450°C presented the highest photoelectrochemical activity. By combining photocatalytic with electrochemical process, a significantly synergetic effect on ammonia degradation was observed with Na_2SO_4 as supporting electrolyte at pH 10.7. Furthermore, the photoelectrocatalytic efficiency on the ammonia degradation was greatly enhanced in presence of chloride ions without the limitation of pH. The degradation rate was improved by 14.8 times reaching 4.98 × 10~(-2) min~(-1) at pH 10.7 and a faster degradation rate of 6.34 × 10~(-2) min~(-1)was obtained at pH 3.01. The in situ photoelectrocatalytic generated active chlorine was proposed to be responsible for the improved efficiency. On the other hand, an enhanced degradation of ammonia using TiNT electrode fabricated in fluorinated organic solution was also confirmed compared to TiNT electrode anodized in fluorinated water solution and TiO_2 film electrode fabricated by sol–gel method. Finally, the effect of chloride concentration was also discussed.     

Pd/CZ/Al2O3催化剂的制备、表征与三效催化性能

以共浸渍法制得的氧化铝负载铈锆固溶体为载体,并浸渍贵金属Pd得到了Pd/CZ/Al₂O₃催化剂.实验结果表明,该催化剂在老化前后都表现出良好的三效催化活性,新鲜样品Pd/CZ/Al₂O₃活性与Pd/CZ相当,老化后样品前者优于后者.结合XRD,BET,TPR等表征手段,讨论了Pd/CZ/Al₂O₃的催化活性特别是高温老化后活性与其组成结构之间的内在关系,揭示了其老化后仍具有较高活性的主要原因在于保持了Pd与CZ/Al₂O₃复合载体之间的强相互作用(SMSI).     

SO2对Ag/Al2O3催化剂上CH3OH还原NO性能的影响

用溶胶-凝胶混合法制备了Ag负载量为5%的Ag/A1₂O₃催化剂.研究了富氧条件下,SO₂对CH₃OH在催化剂上还原NO性能的影响.结果表明,反应气不含SO₂和H₂O时,NO还原活性温度较低,有显著量N₂O生成,这被归因为反应过程中,部分氧化态Ag被还原为金属Ag.添加SO₂或同时添加SO₂和H_{2相似文献}   

Ti/RuO2-IrO2电极电化学方法降解溶液中TBBPA及其降解机理探究

四溴双酚A(TBBPA)是世界上产量和用量最大的溴代阻燃剂之一,在河流、底泥及污水中持久存在,严重威胁环境和人体健康.探讨了阳极为Ti/RuO_2-IrO_2电极的电化学法对溶液中TBBPA的降解效率,并考察了电流密度(5~20 m A·cm~(-2))、初始pH值(3~11)、极板间距(1~3 cm)及电解质浓度(1~40 mmol·L~(-1))对降解速率的影响.研究结果表明,TBBPA的降解遵循一级动力学方程,在溶液初始浓度为5 mg·L~(-1)、电流密度为10 mA·cm~(-2)、电解质浓度为5 mmol·L~(-1)及极板间距为1 cm的条件下,60 min后TBBPA的降解率可达97.2%,且降解速率常数和半衰期分别为0.060 min~(-1)和11.6 min,能量消耗为105.3 k Wh·m~(-3).同时运用HPLC-MS/MS检测出中间产物双酚A(BPA)和2-溴苯酚,并推断其降解途径主要为在羟基自由基(·OH)作用下连续的脱溴过程中,苯环与异丙基之间的C—C键断裂生成BPA和2-溴苯酚.电化学法是一种高效的、有潜力的降解难降解有机污染物的方法,本文将为今后实际废污水中TBBPA的去除提供基础数据和技术参数.     

Mo-modified Pd/Al2O3 catalysts for benzene catalytic combustion

Mo-modified Pd/Al2O3catalysts were prepared by an impregnation method and tested for the catalytic combustion of benzene. The catalysts were characterized by N2 isothermal adsorption, X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, temperatureprogrammed desorption of NH3（NH3-TPD）, H2temperature-programmed reduction（H2-TPR）, and high-angle annular dark-field scanning transmission electron microscopy（HAADF-STEM）. The results showed that the addition of Mo effectively improved the activity and stability of the Pd/Al2O3catalyst by increasing the dispersion of Pd active components, changing the partial oxidation state of palladium and increasing the oxygen species concentration on the surface of catalyst. In the case of the Pd-Mo/Al2O3catalyst,benzene conversion of 90% was obtained at temperatures as low as 190°C, which was 45°C lower than that for similar performance with the Pd/Al2O3catalyst. Moreover, the 1.0% Pd-5% Mo/Al2O3catalyst was more active than the 2.0% Pd/Al2O3catalyst. It was concluded that Pd and Mo have a synergistic effect in benzene catalytic combustion.     

CO2 adsorption using TiO2 composite polymeric membranes: A kinetic study

CO₂ is the main greenhouse gas which causes global climatic changes on larger scale. Many techniques have been utilised to capture CO₂. Membrane gas separation is a fast growing CO₂ capture technique, particularly gas separation by composite membranes. The separation of CO₂ by a membrane is not just a process to physically sieve out of CO₂ through the controlled membrane pore size. It mainly depends upon diffusion and solubility of gases, particularly for composite dense membranes. The blended components in composite membranes have a high capability to adsorb CO₂. The adsorption kinetics of the gases may directly affect diffusion and solubility. In this study, we have investigated the adsorption behaviour of CO₂ in pure and composite membranes to explore the complete understanding of diffusion and solubility of CO₂ through membranes. Pure cellulose acetate (CA) and cellulose acetate-titania nanoparticle (CA-TiO₂) composite membranes were fabricated and characterised using SEM and FTIR analysis. The results indicated that the blended CA-TiO₂ membrane adsorbed more quantity of CO₂ gas as compared to pure CA membrane. The high CO₂ adsorption capacity may enhance the diffusion and solubility of CO₂ in the CA-TiO₂ composite membrane, which results in a better CO₂ separation. The experimental data was modelled by Pseudo first-order, pseudo second order and intra particle diffusion models. According to correlation factor R², the Pseudo second order model was fitted well with experimental data. The intra particle diffusion model revealed that adsorption in dense membranes was not solely consisting of intra particle diffusion.     

g-C3N4/Bi2S3复合物的制备及可见光催化降解MO

采用简单溶剂热方法成功合成可见光催化剂g-C_3N_4/Bi_2S_3.合理地利用X射线衍射(XRD)、傅立叶红外光谱分析仪(FTIR)、场发射扫描电子显微镜(FESEM)、透射电子显微镜(TEM、HRTEM)、紫外可见漫反射光谱(UV-vis DRS)等表征手段对合成的样品进行了表征.与纯g-C_3N_4和Bi_2S_3相比,g-C_3N_4/Bi_2S_3复合物对甲基橙(MO)的可见光催化降解具有更高的降解效率.根据能带分析结果,电子-空穴对的有效分离增强了光催化效率.此外,提出了g-C_3N_4/Bi_2S_3对MO的光催化降解过程以阐明降解机制.提供了一种经济简单并易于规模化扩大开发可见光响应催化剂的方法,并在废水处理中具有潜在的应用价值.     

TiO2/g-C3N4在泡沫陶瓷表面的负载及光催化空气净化性能增强

以市售P25(TiO_2)和g-C_3N_4为原料,以多孔氧化铝泡沫陶瓷为载体,进行了负载型光催化组件的设计与环境应用.运用浸渍提拉-热处理法制备负载P25/g-C_3N_4的泡沫陶瓷组件,对其微结构进行了表征测试,并将其应用于空气中NO的去除.结果表明,P25/g-C_3N_4在氧化铝泡沫陶瓷表面负载牢固,P25/g-C_3N_4禁带结构匹配有利于光生电荷的分离.研究了P25/g-C_3N_4比例对光催化性能的影响,当g-C_3N_4占P25的量为30%时,负载组件的光催化性能最佳,对NO的去除率达到79.6%.在5次循环反应后,负载型光催化剂表现出良好的稳定性.本研究为P25/g-C_3N_4复合光催化剂的空气净化应用提供了思路和技术基础.