Electrical conductivity changes of bulk tin and Sn-3.0Ag-0.5Cu in bulk and in joints during isothermal aging

The changes of electrical conductivity (resistance) between Sn-3.0Ag-0.5Cu solder joints and printed circuit board (PCB) assembly during aging at 125℃ were investigated by the four-point probe technique. The microstructural characterizations of interfacial layers between the solder matrix and the substrate were examined by optical microscopy and scanning electronic microscopy. Different types of specimens were designed to consider several factors. The experimental results indicate that electrical conductivities (resistances) and residual shear strengths of the solder joint specimens significantly decrease after 1000 h during isothermal aging. Microcracks generate in the solder matrix at the first 250 h. Besides, the evolutions of microstructural characterizations at the interface and the matrix of solder joints were noted in this research.     

Microstructure and properties of pure iron/copper composite cladding layers on carbon steel

In the present study, pure iron/copper composite metal cladding was deposited onto carbon steel by tungsten inert gas welding. The study focused on interfacial morphological, microstructural, and mechanical analyses of the composite cladding layers. Iron liquid–solid-phase zones were formed at copper/steel and iron interfaces because of the melting of the steel substrate and iron. Iron concentrated in the copper cladding layer was observed to exhibit belt, globule, and dendrite morphologies. The appearance of iron-rich globules indicated the occurrence of liquid phase separation (LPS) prior to solidification, and iron-rich dendrites crystallized without the occurrence of LPS. The maximum microhardness of the iron/steel interface was lower than that of the copper/steel interface because of the diffusion of elemental carbon. All samples fractured in the cladding layers. Because of a relatively lower strength of the copper layer, a short plateau region appeared when shear movement was from copper to iron.     

Sintering behavior and thermal conductivity of nickel-coated graphite flake/copper composites fabricated by spark plasma sintering

Nickel-coated graphite flakes/copper (GN/Cu) composites were fabricated by spark plasma sintering with the surface of graphite flakes (GFs) being modified by Ni-P electroless plating. The effects of the phase transition of the amorphous Ni-P plating and of Ni diffusion into the Cu matrix on the densification behavior, interfacial microstructure, and thermal conductivity (TC) of the GN/Cu composites were systematically investigated. The introduction of Ni-P electroless plating efficiently reduced the densification temperature of uncoated GF/Cu composites from 850 to 650℃ and slightly increased the TC of the X-Y basal plane of the GF/Cu composites with 20vol%-30vol% graphite flakes. However, when the graphite flake content was greater than 30vol%, the TC of the GF/Cu composites decreased with the introduction of Ni-P plating as a result of the combined effect of the improved heat-transfer interface with the transition layer, P generated at the interface, and the diffusion of Ni into the matrix. Given the effect of the Ni content on the TC of the Cu matrix and on the interface thermal resistance, a modified effective medium approximation model was used to predict the TC of the prepared GF/Cu composites.     

Effect of sintering temperature on phase evolution of Al_(86)Ni_6Y_(4.5)Co_2La_(1.5) bulk amorphous composites synthesized via mechanical alloying and spark plasma sintering

Al_(86)Ni_6Y_(4.5)Co_2La_(1.5) amorphous powders were synthesized by mechanical alloying for 200 h. Subsequent consolidation was performed via spark plasma sintering in the temperature range of 250 ℃ to 500 ℃ at the pressure of 500 MPa. The role of viscous flow on densification was investigated by studying the viscosity change of the amorphous phase at different consolidation temperatures. The decrease in viscosity at higher sintering temperatures resulted in better particle bonding and densification of consolidated samples. The formation of only FCC Al was observed in the consolidated samples at sintering temperatures ≤ 300 ℃ and the intermetallic phases formed at temperatures ≥ 400 ℃. The mechanical properties of the bulk samples were measured by Vickers microhardness and nanoindentation tests. The testing results showed that the average values of microhardness, nanohardness and elastic modulus of the sample consolidated at 500 ℃ were 3.06 ± 0.14 GPa,4.85 ± 1.14 GPa and 89.53 ± 9.25 GPa, respectively. The increase in hardness and elastic modulus of the higher temperature consolidated samples is attributed to the improvement in particle bonding, densification and distribution of various hard intermetallic phases in the amorphous matrix.     

Effects of nano-sized Ag reinforcing particulates on the microstructure of Sn-0.7Cu solder joints

Composite solders were prepared by mechanically dispersing different volumes of nano-sized Ag particles into the Sn-0.7Cu eutectic solder. The effects of Ag particle addition on the microstructure of Sn-0.7Cu solder joints were investigated. Besides, the effects of isothermal aging on the microstructural evolution in the interfacial intermetallic compound (IMC) layer of the Sn-0.7Cu solder and the composite solder reinforced with 1vol% Ag particles were analyzed, respectively. Experimental results indicate that the growth rate of the interfacial IMC layer in the Ag particles reinforced composite solder joint is much lower than that in the Sn-0.7Cu solder joint during isothermal aging. The Ag particles reinforced composite solder joint exhibits much lower layer-growth coefficient for the growth of the IMC layer than the corresponding solder joint.     

Oxidation behavior of niobized TiAl by plasma surface alloying

Plasma surface alloying of element Nb in TiAl-based alloys and the oxidation behavior were studied. The composition and microstructure of the surface alloyed layers were investigated by means of scanning electron microscopy (SEM),energy dispersive X-ray analysis (EDX),and X-ray diffraction (XRD). The experimental results indicate that the diffusion layers are formed on the TiAl substrate during the plasma niobizing process. The result from oxidation resistance investigation shows that plasma niobizing greatly improves the oxidation resistance of TiAl compared with the untreated TiAl. The role of element Nb for improving the oxidation resistance is considered to be achieved by strengthening the activity of Al,which is induced by the plasma niobizing process.     

Microstructure and mechanical properties of SiC-particle-strengthening tri-metal Al/Cu/Ni composite produced by accumulative roll bonding process

In this study, a multilayer Al/Ni/Cu composite reinforced with SiC particles was produced using an accumulative roll bonding (ARB) process with different cycles. The microstructure and mechanical properties of this composite were investigated using optical and scanning microscopy and hardness and tensile testing. The results show that by increasing the applied strain, the Al/Ni/Cu multilayer composite converted from layer features to near a particle-strengthening characteristic. After the fifth ARB cycle, a composite with a uniform distribution of reinforcements (Cu, Ni, and SiC) was fabricated. The tensile strength of the composite increased from the initial sandwich structure to the first ARB cycle and then decreased from the first to the third ARB cycle. Upon reaching five ARB cycles, the tensile strength of the composite increased again. The variation in the elongation of the composite exhibited a tendency similar to that of its tensile strength. It is observed that with increasing strain, the microhardness values of the Al, Cu, and Ni layers increased, and that the dominant fracture mechanisms of Al and Cu were dimple formation and ductile fracture. In contrast, brittle fracture in specific plains was the main characteristic of Ni fractures.     

Selective interfacial bonding and thermal conductivity of diamond/Cu-alloy composites prepared by HPHT technique

Cu-based and Cu-alloy-based diamond composites were made by high-pressure-high-temperature (HPHT) sintering with the aim of maximizing the thermal conductivity of the composites. Improvements in interfacial bonding strength and thermo-physical properties of the composites were achieved using an atomized copper alloy with minor additions of Co, Cr, B, and Ti. The thermal conductivity (TC) obtained exhibited as high as 688 W·m-1·K-1, but also as low as 325 W·m-1·K-1. A large variation in TC can be rationalized by the discrepancy of diamond-matrix interfacial bonding. It was found from fractography that preferential bonding between diamond and the Cu-alloy matrix occurred only on the diamond {100} faces. EDS analysis and Raman spectra suggested that selective interfacial bonding may be attributed to amorphous carbon increasing the wettability between diamond and the Cu-alloy matrix. Amorphous carbon was found to significantly affect the TC of the composite by interface modification.     

Properties of a new type Al/Pb-0.3%Ag alloy composite anode for zinc electrowinning

An Al/Pb-0.3%Ag alloy composite anode was produced via composite casting. Its electrocatalytic activity for the oxygen evolution reaction and corrosion resistance was evaluated by anodic polarization curves and accelerated corrosion test, respectively. The microscopic morphologies of the anode section and anodic oxidation layer during accelerated corrosion test were obtained by scanning electron microscopy. It is found that the composite anode (hard anodizing) displays a more compact interfacial combination and a better adhesive strength than plating tin. Compared with industrial Pb-0.3%Ag anodes, the oxygen evolution overpotentials of Al/Pb-0.3%Ag alloy (hard anodizing) and Al/Pb-0.3%Ag alloy (plating tin) at 500 A·m?2 were lower by 57 and 14 mV, respectively. Furthermore, the corrosion rates of Pb-0.3%Ag alloy, Al/Pb-0.3%Ag alloy (hard anodizing), and Al/Pb-0.3%Ag alloy (plating tin) were 13.977, 9.487, and 11.824 g·m?2·h?1, respectively, in accelerated corrosion test for 8 h at 2000 A·m?2. The anodic oxidation layer of Al/Pb-0.3%Ag alloy (hard anodizing) is more compact than Pb-0.3%Ag alloy and Al/Pb-0.3%Ag alloy (plating tin) after the test.     

Microstructure and mechanical properties of Al/Cu/Mg laminated composite sheets produced by the ARB proces

In the present study, an Al/Cu/Mg multi-layered composite was produced by accumulative roll bonding (ARB) through seven passes, and its microstructure and mechanical properties were evaluated. The microstructure investigations show that plastic instability occurred in both the copper and magnesium reinforcements in the primary sandwich. In addition, a composite with a perfectly uniform distribution of copper and magnesium reinforcing layers was produced during the last pass. By increasing the number of ARB cycles, the microhardness of the layers including aluminum, copper, and magnesium was significantly increased. The ultimate tensile strength of the sandwich was enhanced continually and reached a maximum value of 355.5 MPa. This strength value was about 3.2, 2, and 2.1 times higher than the initial strength values for the aluminum, copper, and magnesium sheets, respectively. Investigation of tensile fracture surfaces during the ARB process indicated that the fracture mechanism changed to shear ductile at the seventh pass.     

A study of interparticulate strain in a hot-extruded SiCp/2014 Al composite

We report a correlative study of strain distribution and grain structure in the Al matrix of a hot-extruded SiC particulate-reinforced Al composite (SiC_p/2014 Al). Finite element method (FEM) simulation and microstructure characterization indicate that the grain structure of the Al matrix is affected by the interparticulate strain distribution in the matrix during the process. Both electron-backscattered diffraction (EBSD) and selected-area electron diffraction (SAED) indicated localized misorientation in the Al matrix after hot extrusion. Scanning transmission electron microscopy (STEM) revealed fine and recrystallized grains adjacent to the SiC particulate and elongated grains between the particulates. This result is explained in terms of recrystallization under an interparticulate strain distribution during the hot extrusion process.     

Interfacial microstructure and mechanical properties of Ti-6Al-4V/Al7050 joints fabricated using the insert molding method

Ti-6Al-4V/Al7050 joints were fabricated by a method of insert molding and corresponding interfacial microstructure and mechanical properties were investigated. The interfacial thickness was sensitive to holding temperature during the first stage, and a good metallurgical bonding interface with a thickness of about 90 μm can be obtained at 750℃. X-ray diffraction, transmission electron microscopy, and thermodynamic analyses showed that the interface mainly contained intermetallic compound TiAl₃ and Al matrix. The joints featured good mechanical properties, i.e., shear strength of 154 MPa, tensile strength of 215 MPa, and compressive strength of 283 MPa, which are superior to those of joints fabricated by other methods. Coherent boundaries between Al/TiAl₃ and TiAl₃/Ti were confirmed to contribute to outstanding interfacial mechanical properties and also explained constant fracture occurrence in the Al matrix. Follow-up studies should focus on improving mechanical properties of the Al matrix by deformation and heat treatment.     

A TiCx reinforced Fe (Al) matrix composite using in-situ reaction

A new Fe matrix composite reinforced by the in-situ generated TiCx grains was prepared using the element Fe and Ti3AlC2 powders as the starting materials.Several hot-pressing temperatures were tried for exploring the phase transformation behavior from Ti3AlC2 to TiC x.Microstructures of the hot-pressed product were observed and analyzed.A tensile test was carried out for the new composite material,and the fracture face was analyzed.The results showed that the starting Ti3AlC2 was wholly decomposed and transformed into submicron TiC x grains at the hotpressing temperature above 1100℃.Most of the Al ions escaped from Ti3AlC2 were aggregated at the grain boundary of Fe grains,but a small amount of Al ions could be absorbed by Fe and formed Fe(Al) alloy around the surface of Fe grains.The prepared material exhibited a higher tensile strength of about 660 MPa and a uniform deformation of about 7%.     

Interfacial microstructure and mechanical properties of Ti-6Al-4V/Al7050 joints fabricated using the insert molding method

Ti-6Al-4V/Al7050 joints were fabricated by a method of insert molding and corresponding interfacial microstructure and mechanical properties were investigated. The interfacial thickness was sensitive to holding temperature during the first stage, and a good metallurgical bonding interface with a thickness of about 90 μm can be obtained at 750°C. X-ray diffraction, transmission electron microscopy, and thermodynamic analyses showed that the interface mainly contained intermetallic compound TiAl_3 and Al matrix. The joints featured good mechanical properties, i.e., shear strength of 154 MPa, tensile strength of 215 MPa, and compressive strength of 283 MPa, which are superior to those of joints fabricated by other methods. Coherent boundaries between Al/TiAl_3 and TiAl_3/Ti were confirmed to contribute to outstanding interfacial mechanical properties and also explained constant fracture occurrence in the Al matrix. Follow-up studies should focus on improving mechanical properties of the Al matrix by deformation and heat treatment.     

添加钇不锈钢热处理过程中其氧化物夹杂物的温度依赖性演化

The evolution of oxide inclusions during isothermal heating of 18Cr–8Ni stainless steel with yttrium addition at temperatures of 1273 to 1573 K was investigated systematically. Homogeneous spherical Al–Y–Si(–Mn–Cr) oxide inclusions were observed in as-cast steel. After heating, most of the homogeneous inclusions were transformed into heterogeneous inclusions with Y-rich and Al-rich parts, even though some homogeneous oxide particles were still observed at 1273 and 1573 K. With the increase in heating temperature, more large-sized inclusions were formed. The shape of the inclusions also changed from spherical to irregular. The maximum transformation temperature of inclusions was determined to be 1373 K. The evolution mechanism of inclusions during heating was proposed to be the combined effect of the (i) internal transformation of inclusions due to the crystallization of glassy oxide and (ii) interfacial reaction between inclusions and steel matrix. Meanwhile, the internal transformation of inclusions was considered to be the main factor at heating temperatures less than 1473 K.     

Microstructure of Ni–Al powder and Ni–Al composite coatings prepared by twin-wire arc spraying

Ni–Al powder and Ni–Al composite coatings were fabricated by twin-wire arc spraying (TWAS). The microstructures of Ni-5wt%Al powder and Ni-20wt%Al powder were characterized by scanning electronic microscopy (SEM) and energy dispersive spectroscopy (EDS). The results showed that the obtained particle size ranged from 5 to 50 μm. The morphology of the Ni–Al powder showed that molten particles were composed of Ni solid solution, NiAl, Ni₃Al, Al₂O₃, and NiO. The Ni–Al phase and a small amount of Al₂O₃ particles changed the composition of the coating. The microstructures of the twin-wire-arc-sprayed Ni–Al composite coatings were characterized by SEM, EDS, X-ray diffraction (XRD), and transmission electron microscopy (TEM). The results showed that the main phase of the Ni-5wt%Al coating consisted of Ni solid solution and NiAl in addition to a small amount of Al₂O₃. The main phase of the Ni-20wt%Al coating mainly consisted of Ni solid solution, NiAl, and Ni₃Al in addition to a small amount of Al and Al₂O₃, and NiAl and Ni₃Al intermetallic compounds effectively further improved the final wear property of the coatings. TEM analysis indicated that fine spherical NiAl₃ precipitates and a Ni–Al–O amorphous phase formed in the matrix of the Ni solid solution in the original state.     

Temperature-dependent evolution of oxide inclusions during heat treatment of stainless steel with yttrium addition

The evolution of oxide inclusions during isothermal heating of 18Cr–8Ni stainless steel with yttrium addition at temperatures of 1273 to 1573 K was investigated systematically. Homogeneous spherical Al–Y–Si(–Mn–Cr) oxide inclusions were observed in as-cast steel.After heating, most of the homogeneous inclusions were transformed into heterogeneous inclusions with Y-rich and Al-rich parts, even though some homogeneous oxide particles were still observed at 1273 and 1573 K. With the increase in heating temperature, more large-sized inclusions were formed. The shape of the inclusions also changed from spherical to irregular. The maximum transformation temperature of inclusions was determined to be 1373 K. The evolution mechanism of inclusions during heating was proposed to be the combined effect of the(i)internal transformation of inclusions due to the crystallization of glassy oxide and(ii) interfacial reaction between inclusions and steel matrix.Meanwhile, the internal transformation of inclusions was considered to be the main factor at heating temperatures less than 1473 K.     

Wear properties of NiAl based materials

The NiAl based materials including NiAl-TiC-Al2O3 composite,NiAl-Cr(Mo)-Hf-Ho eutectic alloy and NiAl-Cr(Mo)-CrxSy in situ composite were fabricated and their wear properties were tested at different temperatures.The results revealed that the NiAl-TiC-Al2O3 composite,NiAl-Cr(Mo)-Hf-Ho eutectic alloy and NiAl-Cr(Mo)-CrxSy in situ composite exhibited the excellent wear properties between 700℃ and 900℃.The microstructure observations exhibited that the self-lubricant films formed on the worn surfaces during the dry sliding test at high temperature,which decreased the wear rate and friction coefficient significantly.TEM observation on the self-lubricant film revealed that it was mainly comprised by ceramic amorphous and nanocrystalline.Compared with the NiAl-TiC-Al2O3 composite,the NiAl-Cr(Mo)-CrxSy in situ composite has lower friction coefficient at low temperature.Such phenomena may be ascribed to the addition of sulfide which contributes much to the formation of self-lubricant,and moreover the TiC addition increase the strength of NiAl based material and its wear resistance.     

Solid FeS lubricant: a possible alternative to MoS_2 for Cu–Fe-based friction materials

Molybdenum disulfide(MoS_2) is one of the most commonly used solid lubricants for Cu–Fe-based friction materials. Nevertheless, MoS_2 reacts with metal matrices to produce metal sulfides(e.g., FeS) and Mo during sintering, and the lubricity of the composite may be related to the generation of FeS. Herein, the use of FeS as an alternative to MoS_2 for producing Cu–Fe-based friction materials was investigated. According to the reaction principle of thermodynamics, two composites—one with MoS_2(Fe–Cu–MoS_2 sample) and the other with FeS(FeS–Cu_2S–Cu–Fe–Mo sample), were prepared and their friction behaviors and mechanical properties were compared. The results showed that MoS_2 reacted with the Cu–Fe matrix to produce FeS, metallic ternary sulfides, and Mo when sintered at 1050°C. The MoS_2–Cu–Fe and FeS–Cu_2S–Cu–Fe–Mo samples thereby exhibited similar characteristics with respect to phase composition, density, hardness, and tribological behaviors. Micrographs of the worn surfaces revealed that the stable friction regime for both composites stemmed from the iron sulfides friction layers rather than from the molybdenum sulfides layers.     

Chemical,mechanical, and thermal expansion properties of a carbon nanotube-reinforced aluminum nanocomposite

In the present study, the chemical and mechanical properties and the thermal expansion of a carbon nanotube (CNT)-based crystalline nano-aluminum (nano Al) composite were reported. The properties of nanocomposites were tailored by incorporating CNTs into the nano Al matrix using a physical mixing method. The elastic moduli and the coefficient of thermal expansion (CTE) of the nanocomposites were also estimated to understand the effects of CNT reinforcement in the Al matrix. Microstructural characterization of the nanocomposite reveals that the CNTs are dispersed and embedded in the Al matrix. The experimental results indicate that the incorporation of CNTs into the nano Al matrix results in the increase in hardness and elastic modulus along with a concomitant decrease in the coefficient of thermal expansion. The hardness and elastic modulus of the nanocomposite increase by 21% and 20%, respectively, upon CNT addition. The CTE of CNT/Al nanocomposite decreases to 70% compared with that of nano Al.