Novel approaches to produce Al2O3– TiC/TiCN– Fecomposite powders directly from ilmenite

Al2O3 –TiC/TiCN–Fe composite powders were successfully prepared directly from ilmenite at 1300–1400℃.The effects of Al/C ratio,sintering atmosphere,and reaction temperature and time on the reaction products were investigated.Results showed that the nitrogen atmosphere was bene cial to the reduction of ilmenite and the formation of Al2O3 –TiC/TiCN–Fe composite powders.When the reaction temperature was between 600 and 1100℃,the intermediate products,TiO2,Ti3O5 and Ti4O7 were found,which changed to TiC or TiCN at higher temperature.Al/C ratio was found to affect the reaction process and synthesis products.When Al addition was 0.5 mol,the Al2O3 phase did not appear.The content of carbon in TiCN rose when the reaction temperature was increased.     

Composition design of superhigh strength maraging stainless steels using a cluster model

The composition characteristics of maraging stainless steels were studied in the present work investigation using a cluster-plus-glue-atom model. The least solubility limit of high-temperature austenite to form martensite in basic Fe–Ni–Cr corresponds to the cluster formula [NiFe12]Cr3,where NiFe12is a cuboctahedron centered by Ni and surrounded by 12 Fe atoms in FCC structure and Cr serves as glue atoms. A cluster formula [NiFe12](Cr2Ni) with surplus Ni was then determined to ensure the second phase(Ni3M) precipitation,based on which new multicomponent alloys [(Ni,Cu)16Fe192](Cr32(Ni,Mo,Ti,Nb,Al,V)16) were designed. These alloys were prepared by copper mould suction casting method,then solid-solution treated at 1273 K for 1 h followed by water-quenching,and finally aged at 783 K for 3 h. The experimental results showed that the multi-element alloying results in Ni3M precipitation on the martensite,which enhances the strengths of alloys sharply after ageing treatment. Among them,the aged [(Cu4Ni12)Fe192](Cr32(Ni8.5Mo2Ti2Nb0.5Al1V1)) alloy(Fe74.91Ni8.82Cr11.62Mo1.34Ti0.67Nb0.32Al0.19V0.36Cu1.78wt%) has higher tensile strengths with YS?1456 MPa and UTS?1494 MPa. It also exhibits good corrosion-resistance in 3.5 wt% NaCl solution.     

Vapor phase codeposition of Cr and Si on Nb-base in situ composites by pack cementation process

In order to identify suitable halide activators and pack compositions for codepositing Cr and Si to form diffusion coatings on Nb-base in situ composites by the pack cementation process, thermochemical calculation was taken to analyze the vapor pressure of halide species generated at high temperatures. NH4Cl, NaF and CrCl3·6H2O were selected as the halide salts. The results of thermochemical calculations suggested that the pack powder mixtures, which contained Cr, Si, halide salts and Al2O3, may be activated by NH4Cl and NaF. According to the thermochemical calculations, the pack powder mixture of 12Cr-6Si-5NH4Cl-77Al2O3 (wt%) activated by NH4Cl was formulated and coating deposition experiments were carried out at 1200 and 1300℃. With adequate control of pack compositions and deposition conditions, it was found that codeposition of Cr and Si could indeed be achieved at these temperatures. The coating has a three-layer structure, of which was mainly composed of Cr2(Nb,X) (X represents Ti and Hf elements), Nb5Si3 and (Nb,Cr)3Si. Then the kinetics of coating growth process affected by temperature was studied. The experimental results of the oxidation showed that the coating can efficiently prevent substrate from oxidizing.     

La2O3–Al2O3 –SiO2 glass-infiltrated 3Y-TZP all-ceramic composite for the dental restora tive application

The 3 mol% yttria stabilized tetragonal zirconia polycrystals (3Y-TZP) powder had three particle size distributions, while the fine one was lower than 100 nm. The 3Y-TZP compact was prepared by dry-pressing under pressures ranged from 10 to 30 MPa and then presintered at 1250°C for 2 h. The matrix dry-pressed under the pressure of 20 MPa had a porosity of 16.7% and could be easily processed by computer aided design and computer aided manufacturing (CAD/CAM), and which had been infiltrated by the La2O3–Al2O3–SiO2 glass at 1200°C for 4 h. The flexural strength and fracture toughness of the composite were 710.7 MPa and 6.51 MPa m^1/2, respectively. The low shrinkage (0.3%) of the composite can satisfy the net-shape fabrication standard. XRD results illustrated that zirconia in the La2O3–Al2O3–SiO2 glass-infiltrated 3Y-TZP all-ceramic composite was mainly in the tetragonal phase. SEM and EDS results indicated that the pores of the matrix were almost filled by the La2O3–Al2O3 –SiO2 glass     

Electrochemical properties of LaFeO3-rGO composite

LaFeO_3-xwt% r GO composite(x = 8, 10, 12) was synthesized by ultraphonic stirring and lyophilization method.SEM, TEM and XRD results show that the perovskite-type LaFeO_3 was dispersed by rGO to form special porous structure due to the gauze-shaped wrinkles and folds structure of rGO. It was found that the special porous structure can effectively increase the specific surface area and suppress particle aggregation of LaFeO_3, thus improving the electrical conductivity and appreciably enhancing the electrochemical properties of LaFeO_3. As compared with LaFeO_3, the maximum discharge capacity of the composite(x=10) increased from 209.5 mAhg~(–1) to 334.6 mAhg~(–1).The High rate dischargeability at a discharge current density of 1500 mAg~(–1)(HRD1500) and the capacity retention rate after 100 charge/discharge cycles(S100) of the composite increased by 9% and 17%, respectively.     

Effect of CuO addition on the sintering temperature and microwave dielectric properties of CaSiO3– Al2O3 ceramics

CuO-doped CaSiO3–1 wt% Al2O3 ceramics were synthesized via a traditional solid-state reaction method, and their sintering behavior,microstructure and microwave dielectric properties were investigated. The results showed that appropriate CuO addition could accelerate the sintering process and assist the densification of CaSiO3–1 wt% Al2O3 ceramics, which could effectively lower the densification temperature from1250 1C to 1050 1C. However, the addition of CuO undermined the microwave dielectric properties. The optimal amount of CuO addition was found to be 0.8 wt%, and the derived CaSiO3–Al2O3ceramic sintered at 1100 1C presented good microwave dielectric properties of εr?7.27,Q f?16,850 GHz and τf? 39.53 ppm/1C, which is much better than those of pure CaSiO3 ceramic sintered at 1340oC(Q f?13,109 GHz).The chemical compatibility of the above ceramic with 30 Pd/70 Ag during the cofiring process has also been investigated, and the result showed that there was no chemical reaction between palladium–silver alloys and ceramics.& 2014 Chinese Materials Research Society. Production and hosting by Elsevier B.V. All rights reserved.     

The strain ampli tude-controlled cyclic fatigue behavior of Al2O3 fiber reinforced Al–Si alloy composite at elevated temperatures

The strain amplitude-controlled fatigue characteristics of an Al–Si casting alloy and itscomposite reinforced with 17 vol% Al₂O₃ fibers (Al–Si/Al₂O₃) are studied at three different temperatures. Both the alloy and the composite showed different degrees of cyclic softening at elevated temperatures. Increasing the temperature, fatigue damage of either the alloy or the composite occurred with varying mode from brittle fracture of silicon particles to their separation from the aluminum matrix. This is explained by the different thermal expansion coefficients of silicon particles and the aluminum matrix. The reinforcement Al₂O₃ fibers in the composite showed a similar damage behavior with those silicon particles despite temperature variation     

Fabrication of Fe–TiC–Al2O3 composites on the surface of steel using a TiO2–Al–C–Fe combustion reaction induced by gas tungsten arc cladding

The aim of the present study was to fabricate Fe–TiC–Al₂O₃ composites on the surface of medium carbon steel. For this purpose, TiO₂–3C and 3TiO₂–4Al–3C–xFe (0 ≤ x ≤ 4.6 by mole) mixtures were pre-placed on the surface of a medium carbon steel plate. The mixtures and substrate were then melted using a gas tungsten arc cladding process. The results show that the martensite forms in the layer produced by the TiO₂–3C mixture. However, ferrite–Fe₃C–TiC phases are the main phases in the microstructure of the clad layer produced by the 3TiO₂–4Al–3C mixture. The addition of Fe to the TiO₂–4Al–3C reactants with the content from 0 to 20wt% increases the volume fraction of particles, and a composite containing approximately 9vol% TiC and Al₂O₃ particles forms. This composite substantially improves the substrate hardness. The mechanism by which Fe particles enhance the TiC + Al₂O₃ volume fraction in the composite is determined.     

Thermal stability and magnetic properties of Fe–Co–M–Zr–Nb–Ge–B(M=Mo,Cr) bulk metallic glasses

Fe62Co8 xMxZr6Nb4Ge1B19(M=Mo, Cr) bulk metallic glasses were synthesized in the diameter range up to 2 mm by copper mold casting,which exhibit high thermal stability and large glass-forming ability. The super-cooled liquid region diminishes by the dissolution of Mo. The addition of 2 at% Cr leads to the broading of the liquid region remarkably, resulting in the improvement of thermal stability. The crystallization takes place through a single exothermic reaction, accompanying the precipitation of more than three kinds of crystallized phases such as α-Fe,Fe2Zr and ZrB2. The Fe-based alloys show soft ferromagnetic properties. The saturation magnetization(ss) decreases with increasing Mo or Cr content while the saturated magnetostriction increases with raising Mo or Cr content. There is no evident change in the ssand coercive force(Hc)with annealing temperature below the crystallization temperature, which suggests a more relaxed atomic configuration the glasses have. The crystallization causes a substantial enhancement in both ssand Hc. Each soft magnetic property of the glasses containing Cr with higher thermal stability is superior to that of the alloys containing Mo.     

Effects of Cr and Mo elements on the microstructures and compressive properties of the in situ (TiC_xN_y–TiB_2)/Ni cermets

In-situ(TiC_xN_y–TiB_2)/Ni cermets with 70 wt%TiC_xN_y–TiB_2 were successfully fabricated by combustion synthesis and hot pressing sintering in Ni-Ti-B_4C-BN powder systems.The microstructures,density,compressive properties,and hardness of the TiC_xN_y–TiB_2/Ni cermets with the addition of 0–8 wt%Cr/Mo to the Ni-Ti-B_4C-BN powder systems were compared and analysed.The results showed that the ceramic particles distributed uniformly in the cermets,and the size of the ceramic particles reduced with the Cr/Mo addition.Both Cr and Mo addition can improve the hardness,compressive properties,and fracture strains of the cermets.The hardness,compressive strength,and fracture strain of the(TiC_xN_y–TiB_2)/(Ni+Cr)cermets increased from 1561 HV,2.94 GPa,and 2.9%to 1864 HV,3.65 GPa,and 3.4%,respectively when the Cr content increased to 5 wt%.The hardness and compressive strength of the(TiC_xN_y–TiB_2)/(Ni+Mo)cermets increased from 1561 HV and 2.94 GPa to 1902 HV and 3.43 GPa,respectively when the Mo content increased to 8 wt%.The cermets with Cr had better compressive properties than the cermets with Mo.     

Microstructure, mechanical and thermo-physical properties of hot-pressed Al2O3-GdAlO3-ZrO2 ceramics with eutectic composition

A low cost chemical co-precipitation method was employed to fabricate nanoscale Al_2O_3-GdAlO_3-ZrO_2 powder with eutectic composition. A careful control of reaction conditions was required during the preparation. The synthesized nanopowders exhibited a particle size of 20-200 nm, and were highly dispersive and uniform. The results showed that calcination temperature had an important influence on the phase constituents of the nanopowders. With increasing the calcination temperature, a phase transformation from θ-Al_2O_3 to α-Al_2O_3 and a thermal decomposition from Gd_3 Al_5O_(12)(GdAG) to GdAlO_3 and α-Al_2O_3 occurred in sequence. A calcination temperature of 1300 ℃ was needed for the crystallization of α-Al_2 O_3. These nanosized powders were consolidated via hot pressing to produce a fully densified ceramic composite with eutectic composition. The Al_2O_3-GdAlO_3-ZrO_2 ceramic hot-pressed at 1500 ℃ exhibited a relative density of 99.4%, a flexural strength of 485 MPa and a fracture toughness of 6.5 MPa m~(1/2). The ceramic had a thermal conductivity of 1.9 W m K~(-1) at 1200 ℃ and a thermal expansion coefficient of 9.49 ×10~(-6) K~(-1) at 1100 ℃.     

ZrO2 strengthened NiAl/Cr(Mo,Hf) composite fabricated by powder metallurgy

The ZrO2 ceramic particles strengthened NiAl/Cr(Mo,Hf) composite was fabricated from the rapidly solidified NiAl/Cr(Mo,Hf) pre-alloyed powder and the ZrO2 powder by powder metallurgy technique.Microstr...     

Minor-alloyed Cu-Ni-Si alloys with high hardness and electric conductivity designed by a cluster formula approach

Cu-Ni-Si alloys are widely used due to their good electrical conductivities in combination with high strength and hardness. In the present work, minor-alloying with M =(Cr, Fe, Mo, Zr) was conducted for the objective of further improving their hardness while maintaining their conductivity level. A cluster-plus-glue-atom model was introduced to design the compositions of M-alloyed Cu-Ni-Si alloys, in which an ideal composition formula[(Ni,Si,M)-Cu_(12)]Cu_3(molar proportion) was proposed. To guarantee the complete precipitation of solute elements in fine δ-Ni_2 Si precipitates, the atomic ratio of(Ni,M)/Si was set as 2/1. Thus the designed alloy series of Cu_(93.75)(Ni/Zr)_(3.75)Si_(2.08)(Cr/Fe/Mo)_(0.42)(at%) were arc-melted into ingots under argon atmosphere, and solidsolutioned at 950 ℃ for 1 h plus water quenching and then aged at 450 ℃ for different hours. The experimental results showed that these designed alloys exhibit high hardness(HV 1.7 GPa) and good electrical conductivities(≥ 35% IACS). Specifically, the quinary Cu_(93.75)Ni_(3.54)Si_(2.08)(Cr/Fe)_(0.42)Zr_(0.21) alloys(Cu-3.32 Ni-0.93 Si-0.37(Cr/Fe)-0.30 Zr wt%) possess both a high hardness with HV = 2.5-2.7 GPa, comparable to the highstrength KLFA85 alloy(Cu-3.2 Ni-0.7 Si-1.1 Zn wt%,HV= 2.548 GPa),and a good electrical conductivity(35-36% IACS).     

Competing crystallite size and zinc concentration in silica coated cobalt ferrite nanoparticles

Silica coated(30 wt%) cobalt zinc ferrite(Co1 xZnxFe2O4, x?0, 0.2, 0.3, 0.4, 0.5 and 1) nanoparticles were synthesized by using sol–gel method. Silica acts as a spacer among the nanoparticles to avoid the agglomeration. X-ray diffraction(XRD) reveals the cubic spinel ferrite structure of nanoparticles with crystallite size in the range 37–45 nm. Fourier transform infrared(FTIR) spectroscopy confirmed the formation of spinel ferrite and SiO2. Scanning electron microscopy(SEM) images show that the nanoparticles are nearly spherical and non-agglomerated due to presence of non-magnetic SiO2 surface coating. All these measurements signify that the structural and magnetic properties of Co1 xZnxFe2O4 ferrite nanoparticles strongly depend on Zn concentration and nanoparticle average crystallite size in different Zn concentration regimes.& 2014 Chinese Materials Research Society. Production and hosting by Elsevier B.V. All rights reserved.     

Solvother mal synthesis of Co1-xNixFe2O4 nanoparticles and its application in ammonia vapors detection

Magnetic Co1-xNixFe2O4 nanoparticles (NPs) were successfully synthesized via a solvothermal method using ethylene glycol as solvent.The samples were characterized by X-ray diffraction (XRD),field emiss...     

Effect of Sr on microstructure and aging behavior of Mg–14Li alloys

The as-cast and as-extruded Mg–14 wt%Li–x Sr ( x=0.14, 0.19, 0.39 wt%) alloys were,respectively, prepared through a simple alloying process and hot extrusion. The effects of Sr addition on microstructure and aging behavior of the Mg–14 wt%Li–xSr alloys were studied. The results indicated that β(Li) and Mg2Sr were the two primary phases in the microstructures of both as-cast and as-extruded Mg–14 wt%Li–xSr alloys. Interestingly, with the increase of Sr content from 0.14 wt% to 0.39 wt%, the grain sizes of the as-cast and as-extruded Mg–14 wt%Li–xSr alloys markedly decreased from 5000mm and 38mm to 330 mm and 22mm respectively, while no obvious changes of the micro-hardness and microstructure of the as-extruded alloys were observed during the aging treatment.     

Densification behavior of mechanically milled Cu–8 at% Cr alloy and its mechanical and electrical properties

Synthesis and consolidation behavior of Cu–8 at%Cr alloy powders made by mechanical alloying with elemental Cu and Cr powders,and subsequently,compressive and electrical properties of the consolidated alloys were studied.Solid solubility of Cr in Cu during milling,and subsequent phase transformations during sintering and heat treatment of sintered components were analyzed using X-ray diffraction,scanning electron microscopy and transmission electron microscopy.The milled powders were compacted applying three different pressures(200 MPa,400 MPa and 600 MPa)and sintered in H2atmosphere at 900 1C for 30 min and at 1000 1C for 1 h and 2 h.The maximum densification(92.8%)was achieved for the sample compacted at 600 MPa and sintered for 1000 1C for 2 h.Hardness and densification behavior further increased for the compacts sintered at 900 1C for 30 min after rolling and annealing process.TEM investigation of the sintered compacts revealed the bimodal distribution of Cu grains with nano-sized Cr and Cr2O3precipitation along the grain boundary as well as in grain interior.Pinning of grain boundaries by the precipitates stabilized the fine grain structure in bimodal distribution.     

A.C. conductivity and relaxation dynamics in zinc–borate glasses

The frequency-dependent dielectric dispersion of ZnO–Na2O–Al2O3–B2O3(in mol%) glass prepared by the melt quenching technique is investigated in the temperatur e ranges from room temperature to 420 K. Dielectric relaxation has been analyzed based on the behavior of electric modulus behavior. An analysis of the real and imaginary parts of dielectric is performed assuming the ideal Debye behavior as confirmed by Cole–Cole plot. The activation energy associated with the dielectric relaxation determined from the electric modulus spectra was found to be 1.863 eV, which is close to that the activation energy for d.c. conductivity (1.871 eV), indicating the similar nature of relaxation and conductivity.     

Induced modi fi cations in the properties of Sr doped BiFeO3 multiferr oics

Multiferroics exhibit unique combination of ferroic properties,simultaneously.For instance,in BiFeO3,magnetic and electric properties co-exist.In this work,BiFeO3 and Sr-doped BiFeO3 samples with general formula,Bi1-x Srx FeO3(x=0.00,0.05,0.10,0.20,and 0.30) were synthesized by sol-gel auto-combustion technique,in order to investigate these ferroic properties.The samples were confrmed to have perovskite type rhombohedral structure,characteristic of BiFeO3.A dilute phase of Bi2Fe4O9was also found in all the Sr-doped samples.The micrographs of the palletized samples revealed that minutely doped Sr might not have any effect on the morphology of the samples.Frequency dependent dielectric measurements were carried out at room temperature for all the samples from 100 Hz to 1 MHz.The dielectric constant of un-doped sample at low frequency was 52 which decreased with increasing Sr doping.An enhancement of magnetic properties was observed with increasing the Sr contents.Pure BiFeO3 material was observed to have the least value of remanent magnetization.As the Sr2+ tions were doped in BiFeO3,its magnetization and remanence were increased to 0.867 emu/g and 0.175 emu/g,respectively,at x=0.30.     

Integrated Bi2O3 nanostructure modified with Au nanoparticles for enhanced photocatalytic activity under visible light irradiation

An integrated Bi_2O_3(i-Bi_2O_3) nanostructure with a particle size 10 nm inducing agglomerated structure were synthesized by dissolving bismuth nitrate pentahydrate in diethylene glycol at 180 ℃ with post heat treatment.The prepared i-Bi_2O_3 nanostructures were employed for the construction of Au/i-Bi_2O_3 composite system and characterized by X-ray diffraction pattern,UV-visible diffuse reflectance spectroscopy(DRS),and transmission electron microscopy,X-ray photoemission spectroscopy(XPS) and Energy dispersive X-ray spectroscopy(EDS).The i-Bi_2O_3 nanostructure and Au/i-Bi_2O_3 composite system were found to exhibit high photocatalytic activity than commercial Bi_2O_3 in decomposing salicylic acid under visible light irradiation.The high catalytic activity of i-Bi_2O_3 nanostructure was deduced to be caused by charge separation facilitated by electron hopping between the particles within the integrated structure and space-charge separation between i-Bi_2O_3 and Au.The charge separation behavior in i-Bi_2O_3 nanostructure was further bolstered by comparing the measured.OH radical produced in the solution with i-Bi_2O_3 nanostructure,commercial Bi_2O_3 and Au/i-Bi_2O_3 composite which readily react with 1,4-terephthalic acid(TA) inducing 2-hydroxy terephthalic acid(TAOH) that shows unique fluorescence peak at 426 nm.The space-charge separation between i-Bi_2O_3 and An was confirmed by measuring the electron spin resonance(ESR) spectra.