石墨相氮化碳表面包覆改善锂离子电池正极材料LiCoO2电化学性能的研究

通过简单的固相法和液相法,分别制备出石墨相氮化碳（g-C₃N₄）表面改性的商品化LiCoO₂复合材料,采用扫描电子显微镜观察改性后的材料,发现g-C₃N₄都均匀地包裹在LiCoO₂表面。两种g-C₃N₄-LiCoO₂复合材料被用作锂离子电池的正极材料,电化学测试结果显示,固相法制得的g-C₃N₄-LiCoO₂复合材料在0.2 C的倍率下充放电测试,首次比容量达167 mA·h·g^-1,循环80次后,比容量仍达132 mA·h·g^-1,高于未经g-C₃N₄包裹的纯LiCoO₂（98 mA·h·g^-1）;液相法制得的Y-C₃N₄-LiCoO₂复合材料循环稳定性明显优于同类材料,循环80次后容量保持率均在95%以上。试验证实,g-C₃N₄表面改性的策略具有一定的实用价值,改性后,材料优异的电化学性能归因于g-C₃N₄的包裹处理,这不仅增强了固体电解质界面（SEI）的稳定性,也抑制了锂离子嵌入/脱出电极材料时引起LiCoO₂体积的变化。     

固体酸催化混合胺的CO2解吸性能分析

碳捕获与封存技术（CCS）是针对能源危机的一种综合性解决方案,胺基溶液CO₂吸收与解吸是其关键技术步骤。试验以胺基溶液乙醇胺（MEA）为主体吸收剂,分别选取N-甲基二乙醇胺（MDEA）和4-（二乙胺）-2-丁醇（DEAB）为添加剂,然后分别选取γ-Al₂O₃和沸石分子筛（HZSM-5）为催化剂,探究不同配比条件对MEA的CO₂解吸性能的影响。试验结果表明,添加DEAB比添加MDEA所消耗的热负荷更少,最高可减少61.8%,最低可达0.15~0.20 MW·h·t^-1 CO₂。相对于γ-Al₂O₃,HZSM-5能更显著地提高反应速率,反应速率最高可达17.2×10^-3 mol·L^-1·h^-1。5 M（mol/L）MEA/1.25 M DEAB+HZSM-5的组合效果最佳,是胺基溶液CO₂解吸的优选方案。     

TiO2/CB-NiCo2O4修饰玻碳电极的制备及其对葡萄糖的电化学测定

利用低温下的水化学生长法合成了镍钴氧化物（NiCo₂O₄）纳米针,因其自组装而表现出立方晶相,再用二氧化钛/炭黑（TiO₂/CB）对NiCo₂O₄表面进行了改性,合成了TiO₂/CB-NiCo₂O₄复合纳米材料.用X射线光电子能谱仪（XPS）、扫描电子显微镜（SEM）、能量色散X射线光谱仪（EDX）图谱对材料的形貌进行了表征,运用循环伏安法（CV）、时间-电流（i-t）曲线法考察了TiO₂/CB-NiCo₂O₄修饰玻碳电极的电化学行为.实验发现：TiO₂/CB-NiCo₂O₄修饰电极对葡萄糖的氧化有良好的电催化性能,其线性范围为0.001~1.780 mmol·L^-1,检测限为0.53 μmol·L^-1（信噪比S/N=3）.将该法用于实际样品中葡萄糖的测定,结果令人满意.     

泡沫镍上原位生长CoMn2O4多级空心纳米球作为超级电容器电极材料的电化学性能研究

采用水热法结合空气气氛中的热处理过程,在泡沫镍（NF）表面生长了锰酸钴（CoMn₂O₄）多级空心纳米球,通过X射线衍射仪（XRD）、场发射扫描电镜（FE-SEM）和X射线光电子能谱（XPS）等测试手段对纳米球进行了表征.在三电极电化学测量系统中,0.1Co²⁺-250电极材料在5 mA·cm^-2时的面积比电容高达6 184 mF·cm^-2.以0.1Co²⁺-250为正极,商用活性炭（AC）为负极组装而成的混合超级电容器,在1.6 mW·cm^-2时的最大能量密度为0.112 mWh·cm^-2.即使在功率密度为16 mW·cm^-2时,能量密度仍达到0.064 mWh·cm^-2.在2 mA·cm^-2的电流密度下,经过10 000次充放电循环后,电容保持了初始值的93%.因其优越的电化学性能和低成本的便捷合成方法,CoMn₂O₄多级空心纳米球作为电极材料具有重要的应用前景.     

CoFe2O4-Al2O3复合材料的制备及其在含日落黄废水处理中的应用

制备了铁酸钴-氧化铝（CoFe₂O₄-Al₂O₃）复合材料,并采用扫描电子显微镜（SEM）、X射线衍射（XRD）、比表面积和孔径分析仪对多孔CoFe₂O₄-Al₂O₃复合材料的物相和形貌进行了分析. 利用制备的CoFe₂O₄-Al₂O₃复合材料活化过硫酸氢钾（PMS）来降解废水溶液中的日落黄（SY）,通过研究CoFe₂O₄-Al₂O₃材料制备过程中Co²⁺,Fe³⁺和Al³⁺的物质的量之比、煅烧温度和时长对材料催化性能的影响,发现Co²⁺,Fe³⁺和Al³⁺的最佳物质的量之比为1:2:12,最佳煅烧温度为400 ℃和最佳煅烧时长为3 h. 对采用在最优条件下制得的CoFe₂O₄-Al₂O₃复合材料作为催化剂,PMS氧化降解含日落黄废水进行研究,考察了pH值、温度、不同体系、PMS用量、CoFe₂O₄-Al₂O₃材料用量和一些阴离子对日落黄降解的影响. 结果表明：在pH=7,温度为55 ℃条件下,用0.1 g催化剂和0.125 g PMS能使100 mL质量浓度为0.6 g·L^-1的日落黄溶液在30 min内降解率达到99.5%. 同时,碳酸氢根负离子（HCO₃^-）和硝酸根负离子（NO₃^-）的加入抑制了日落黄的降解,而Cl^-则能促进日落黄的降解. 此外,在进行4次循环使用后,CoFe₂O₄-Al₂O₃仍表现出很好的催化性能,日落黄去除效果仍能达到90%以上.     

基于透明微针拉曼原位检测H2O2

在聚甲基丙烯酸甲酯-微针（PMMA-MNs）阵列上修饰聚多巴胺（PDA）层,通过离心技术将金纳米粒子（Au NPs）组装在MNs表面,构建纳米金@聚多巴胺@聚甲基丙烯酸甲酯微针阵列（Au@PDA@MNs）.Au@PDA@MNs有强表面增强拉曼散射（SERS）效应,以罗丹明6G（R6G）作为拉曼探针,在10^-4~10^-8 mol·L^-1的范围内有良好的线性响应,检测限（LOD）可达3.1×10^-10 mol·L^-1.为了检测过氧化氢（H₂O₂）,4-巯基苯硼酸（4-MPBA）被修饰在Au@PDA@MNs上以构建功能化的MNs.利用4-MPBA分子氧化生成4-羟基硫代苯酚（4-HTP）和MNs的透光性,基于1 000 cm^-1和1 068 cm^-1处拉曼强度比（I_{1 000}/I_{1 068}）的变化,完成了H₂O₂的拉曼定量检测,I_{1 000}/I_{1 068}的变化与H₂O₂浓度成定量关系.线性响应范围为10~2 000 μmol·L^-1,LOD为0.93 μmol·L^-1.MNs和SERS技术的结合为确定具有短半衰期和弱拉曼信号的疾病相关生物标志物开辟了一条新途径.     

Ce0.8Sm0.2O1.9@TiO2异质结构电解质研究

半导体与离子导体形成的异质结构可以极大地增强材料的离子电导率,其两相界面能为离子传输提供较好的通道。以TiO₂与Ce_0.8Sm_0.2O_1.9 （samarium doped ceria, SDC）为研究对象,分别通过湿化学法和干混法构造了两种不同的异质结构复合材料。研究表明,利用湿化学法制备的SDC@TiO₂异质结构复合材料（简称SDC@TiO₂）作电解质的燃料电池在550 ℃下最大输出功率密度为761 mW·cm^-2,比用干混法制备的SDC-TiO₂异质结构复合材料（简称SDC-TiO₂）作电解质的燃料电池的最大输出功率密度高21%。与SDC-TiO₂相比,SDC@TiO₂具有更丰富的两相界面。电化学阻抗谱显示,以SDC@TiO₂材料作为电解质的电池具有更低的欧姆电阻和极化电阻。     

阳极氧化Ti-6Al-4V合金表面TiO2多孔膜的制备及研究

在一定浓度的H₂SO₄溶液中对Ti-6Al-4V合金表面进行阳极氧化处理,通过改变阳极氧化处理的电压、氧化时间和电解液浓度,研究了预处理工艺参数对钛合金表面形貌、物相、润湿性及粗糙度的影响.试验结果表明：钛合金经过阳极氧化处理后,表面出现了二氧化钛（TiO₂）纳米多孔结构,多孔氧化膜由锐钛矿型和金红石型TiO₂组成;在0.5 mol·L^-1 H₂SO₄溶液中,随着阳极氧化电压的增加,多孔膜的孔径逐渐增大,基体表面与模拟体液（SBF）的接触角明显降低,经120 V氧化处理的试样表面接触角由预处理前的52.8°降至16.9°左右,具有良好的润湿性;并且试样表面的粗糙度明显增加,在电压为120 V时粗糙度达到0.56 μm.在电压120 V时,随着阳极氧化时间或电解液浓度的增加,TiO₂多孔膜的含量和孔径尺寸逐渐增大,试样表面的润湿性和粗糙度也不断增加,在氧化时间10 min或电解液浓度0.5 mol·L^-1时达到最大,氧化时间大于10 min或电解液浓度高于0.5 mol·L^-1时,试样表面出现裂纹,多孔结构被破坏.     

氮化碳自组装包裹对SnO2TiO2复合锂离子电池负极材料电化学性能的影响

通过简单的石墨相氮化碳(g-C₃N₄)纳米片自组装沉积法,制备了g-C₃N₄包裹的SnO₂-TiO₂纳米复合材料.扫描电子显微镜观察显示,g-C₃N₄均匀地包裹在SnO₂-TiO₂纳米颗粒上.SnO₂-TiO₂-C₃N₄纳米复合材料被用作锂离子电池的负极材料,在0.2C的倍率下循环20次后,比容量达到380.2 mA·h·g^-1,明显高于未经g-C₃N₄包裹的纯的SnO₂(51.6 mA·h·g^-1)和SnO₂-TiO₂纳米复合材料.在0.1~0.5C的倍率充放电测试中,SnO₂-TiO₂-C₃N₄纳米复合材料的比容量仅从490 mA·h·g^-1衰减到330 mA·h·g^-1,高倍率下抗衰减性能优于同类材料.材料优异的电化学性能归功于g-C₃N₄的包裹处理,这不仅增强了固体电解质界面(SEI)的稳定性,也抑制了锂离子嵌入-脱出时SnO₂和TiO₂纳米颗粒的体积变化.     

NaBH4还原改性TiO2(B)及光催化性能研究

以TiCl₄为原料,在（CH₂OH）₂溶液中通过一步水热法制备单斜相二氧化钛[TiO₂(B)]。使用不同质量含量NaBH₄对TiO₂(B)进行还原改性,调控其内含Ti³⁺的浓度,合成了含Ti³⁺的TiO₂(B)-NaBH₄X样品。采用X射线衍射仪（X-ray diffraction,XRD）、拉曼光谱仪（Raman spectroscopy）、紫外-可见漫反射光谱仪（UV-visible diffuse reflectance spectroscopy,UV-DRS）、X射线光电子能谱仪(X-ray photoelectron spectroscopy,XPS）对材料进行表征。改性后TiO₂(B)-NaBH₄X样品保持其原有晶体结构,并未发生相变,仅有结晶度的改变。原始TiO₂(B)禁带宽度为3.15 eV,通过改性,Ti³⁺的存在改变了禁带宽度,成功地将禁带宽度降低到2.82 eV,将吸光区域扩展到可见光区域。通过可见光光催化分解水制氢与可见光降解甲基橙试验,确立了TiO₂(B)-NaBH₄3样品有最好的可见光光催化活性,产氢速率达到0.58 μmol·h^-1·g^-1,6 h降解率达到40%。     

Selective interfacial bonding and thermal conductivity of diamond/Cu-alloy composites prepared by HPHT technique

Cu-based and Cu-alloy-based diamond composites were made by high-pressure-high-temperature (HPHT) sintering with the aim of maximizing the thermal conductivity of the composites. Improvements in interfacial bonding strength and thermo-physical properties of the composites were achieved using an atomized copper alloy with minor additions of Co, Cr, B, and Ti. The thermal conductivity (TC) obtained exhibited as high as 688 W·m-1·K-1, but also as low as 325 W·m-1·K-1. A large variation in TC can be rationalized by the discrepancy of diamond-matrix interfacial bonding. It was found from fractography that preferential bonding between diamond and the Cu-alloy matrix occurred only on the diamond {100} faces. EDS analysis and Raman spectra suggested that selective interfacial bonding may be attributed to amorphous carbon increasing the wettability between diamond and the Cu-alloy matrix. Amorphous carbon was found to significantly affect the TC of the composite by interface modification.     

Effects of boron on the microstructure and thermal properties of Cu/diamond composites prepared by pressure infiltration

Diamond reinforced copper (Cu/diamond) composites were prepared by pressure infiltration for their application in thermal management where both high thermal conductivity and low coefficient of thermal expansion (CTE) are important. They were characterized by the microstructure and thermal properties as a function of boron content, which is used for matrix-alloying to increase the interfacial bonding between the diamond and copper. The obtained composites show high thermal conductivity (>660 W/(m·K)) and low CET (<7.4×10-6 K-1) due to the formation of the B₁₃C₂ layer at the diamond-copper interface, which greatly strengthens the interfacial bonding. Thermal property measurements indicate that in the Cu-B/diamond composites, the thermal conductivity and the CTE show a different variation trend as a function of boron content, which is attributed to the thickness and distribution of the interfacial carbide layer. The CTE behavior of the present composites can be well described by Kerner’s model, especially for the composites with 0.5wt% B.     

Fabrication and thermal conductivity of copper matrix composites reinforced by tungsten-coated carbon nanotubes

Carbon nanotubes (CNTs) were coated by tungsten using metal organic chemical vapor deposition. Magnetic stirring was employed to disperse the W-coated CNTs (W-CNTs) in a Cu matrix, and then, the mixed powders were consolidated by spark plasma sintering. The W-CNTs obtained a uniform dispersion within the Cu matrix when the W-CNT content was less than 5.0vol%, but high content of W-CNTs (10vol%) resulted in the presence of clusters. The W-CNT/Cu composites containing low content of W-CNTs (<5.0vol%) exhibited a higher thermal conductivity than the sintered pure Cu, while the CNT/Cu composites exhibited no increase in thermal conductivity after the incorporation of uncoated CNTs. The W-CNT content was found to play a crucial role in determining the thermal conductivity of the W-CNT/Cu composites. The thermal conductivity of the W-CNT/Cu composites increased first and then decreased with the W-CNT content increasing. When the W-CNT content was 2.5vol%, the W-CNT/Cu composite obtained the maximum value of thermal conductivity. The thermal resistance of the (W-CNT)-Cu interface was predicted in terms of Maxwell-Garnett effective medium approximation, and its calculated value was about 3.0×10-9 m2·K·W-1.     

Phase analysis and thermal conductivity of in situ O′-sialon/β-Si3N4 composites

Typical O??-sialon-based ceramics, with a formula of Si_2?x Al _x O_1+x N_2?x , where x was set as 0.25, were fabricated by in-situ synthesis. Si₃N₄, Al₂O₃, and SiO₂ powders were used as raw materials, and MgO and Y₂O₃ were added as sintering additives. All the samples were sintered at different temperatures under a nitrogen pressure of 0.25?C0.30 MPa, and their microstructure, phase content, and thermal conductivity were evaluated. The effects of O??-sialon and ??-Si₃N₄ on the thermal conductivity were analyzed by numerical calculation in detail. In the case of the similar porosity, the thermal conductivity of O??-sialon-based ceramics decreased with the ratio of O??-sialon/??-Si₃N₄ increasing. When the ratio was 12, the thermal conductivity of O??-sialon ceramics sintered at 1360°C was 1.197 W·m^?1·K^?1.     

Kinetic studies of the decomposition reaction of adducts of dinuclear Fe(Ⅱ)/O2

Kinetic studies of the decomposition reaction of dinuclear Fe(Ⅱ) adducts [Fe₂(N-Et-HPTB){O₂P(OPh)₂}](Cl- O₄)₂ (1) and [Fe₂(N-Et-HPTB) {O₂P(Ph)₂}] (ClO₄)₂ (2) with O₂ have been carried out at low temperature using UV-vis spectra. The decomposition reaction of Fe(Ⅱ)/O₂ adducts was first-order in the experimental conditions, and the activation parameters were obtained. ?H^¹ = 85.62 kJ·mol^-1, ?S¹ = 19.43 J·mol^-1·K^-1 for compound (1) and ?H^¹ = 97.97 kJ·mol^-1, ?S^¹ = 55.68 J·mol^-1·K^-1 for compound (2). These results are similar to those of dioxygen adducts of other metals complexes and natural enzymes such as methane mono- oxygenase (MMOH).     

Inorganic-organic hybrids constructed of bis（undecatungstogerma- nate）lanthanates polyoxoanions and oxalate-bridged dinuclear copper complexes and their magnetic properties

A series of inorganic-organic hybrids K₂Na _m H_9−m [{Ln(GeW₁₁O₃₉)₂}{Cu₂(bpy)₂(μ-ox)}]·nH₂O (bpy = 2,2-bipyridine and ox = oxalate; Ln = La, Nd, Sm, Eu, Gd; n = 19, 17, 22, 20, 19; m = 4, 4, 4, 9, 2) were isolated after reacting in a potassium acetate buffer. X-ray structural analyses show that compounds 1–5 are isomorphic and consist of [Ln(GeW₁₁O₃₉)₂]¹³⁻ polyoxoanion building blocks and oxalate-bridged dinuclear copper metalorganic complex with a 1D chain structure. The 1D chain further connects into the 3D framework by π-π interactions with neighboring bpy groups. The magnetic susceptibility data indicate that antiferromagnetic coupling between the neighboring Cu²⁺ ions in the structure and the rare earth ions affects magnetic property of the structure.     

Observation of internal tides and near-inertial motions in the upper 450 m layer of the northern South China Sea

Mooring ADCP current observations from August to November are used to study the barotropic tides, baroclinic tides and near-inertial motions in the upper 450 m layer of the northern South China Sea. The barotropic and baroclinic tides at the mooring station are all dominated by M2, K1, O1, P1, with the barotropic amplitudes being 7.8 cm·s^-1, 7.0 cm·s^-1, 5.4 cm·s^-1 and 3.5 cm·s^-1 respectively. The amplitudes of M2, K1, O1, P1 internal tides vary greatly, which are 12--15 cm·s^-1 in the thermocline, and then decrease with increasing depth. The amplitude of the barootropic near-inertial motions is less than 1 cm·s^-1, contributing little to the barotropic currents. However, that of the baroclinic nearinertial motions can be as large as 5 cm·s^-1. The inclination of tidal ellipse tends to increase with increasing depth, implying upward propagation of energy, while that of the near-inertial ellipse tends to decrease with increasing depth, implying downward propagation of energy.     

Studies on reduced extent method for inhibited thermokinetics of enzyme-catalyzed reaction

The thermokinetic reduced extent equations of reversible inhibitions for Michaiels-Menten enzymatic reaction were deduced, and then the criteria for distinguishing inhibition type was given and the methods for calculating kinetic parameters,K _M,K _i andv _m were suggested. This theory was applied to inverstigate the inhibited thermokinetics of laccase-catalyzed oxidation ofo-dihydroxybenzene bym-dihydroxybenzene. The experimental results show the inhibition belongs to reversible competitive type,K _M=6.224×10⁻³ mol·L⁻¹,K _i=2.363×10⁻² mol·L⁻¹. Xiong Ya: born Sep. 1961, Ph. D. graduate student. Curent research interest is in biothermochemistry research Supported by the National Natural Science Foundation of China     

Doping effect on thermoelectric properties of nonstoichiometric AgSbTe<Subscript>2</Subscript> compounds

Nonstoichiometric ternary thermoelectric materials Ag_0.84Sb_1.15M_0.01Te_2.16 (M=Ce, Yb, Cu) were prepared by a direct melt-quench and hot press process. The carrier concentration of all the samples increased after doping. Thermoelectric properties, namely electrical conductivity, Seebeck coefficient, and thermal conductivity, were measured from 300 to 673 K. The phase transition occurring at about 418 K representing the phase transition from β-Ag₂Te to α-Ag₂Te influenced the electrical transport properties. The electrical conductivities of Ce and Yb doped samples increased after doping from 1.9×10⁴ to 2.5×10⁴ and 2.3×10⁴ S·m⁻¹, respectively, at 673 K. Also, at room temperature, the Seebeck coefficient of the Ce doped sample relatively increased corresponding to the high carrier concentration due to the changes in the band structure. However, all the thermal conductivities increased after doping at low temperature. Because of the higher thermal conductivity, the dimensionless figure of merit ZT of these doped samples has not been improved.     

三聚磷酸二氢铝二水物的合成和表征

用磷酸和氢氧化铝为原料制备三聚磷酸二氢铝二水物。用X-衍射、红外光谱、化学分析、DTA-TG结合X-ray分析,证明产品的化学结构式为AlH2P3O10*2H2O。其晶体结构属正交晶系,空间群为PZ1/bZ1/aZ/m,D92h,晶胞参数a=15.919×10-8 cm,b=8.884×10-8cm,c=9.936×10-8 cm,单位晶胞体积V=1 405×10-8 cm3,Z=6。防绣性能测试表明其防锈能力与红丹颜料相当。毒理学试验表明该颜料半致死量LD50=18.0 g/kg(小白鼠),属实际无毒级,符合食品容器及儿童玩具涂装的要求。