PLD法制备氧化锌薄膜生长机制及发光特性的研究

利用PLD法在Si衬底上成功地制备了具有较好C轴择优取向生长的ZnO薄膜,从样品的XRD谱可以看出在环境氧压为20Pa,衬底温度为700℃时生长的样品的XPD谱(002)峰半高宽较窄,膜的结晶程度最好.不同的衬底温度下膜的生长机制也不一样,主要有:V-L-S机制和V-S机制.样品室温下的PL谱显示所有样品均出现UV发射和可见光区蓝绿光发射,而蓝绿光发射强度随氧压的增大而增强,表明样品的蓝绿光发射来源于样品中的受主缺陷.     

PLD工艺制备高质量ZnO/Si异质外延薄膜

采用脉冲激光沉积工艺在不同条件下以Si(111)为衬底制备了Zno薄膜.通过对不同氧压下(0～50Pa)沉积的样品的室温PL谱测试表明,氧气氛显著地提高了薄膜的发光质量,在50Pa氧气中沉积的ZnO薄膜具有最强的近带边UV发射.XRD测试说明在氧气氛中得到的薄膜结晶质量较差,没有单一的(002)取向.利用-低温(500℃)沉积的ZnO薄膜作缓冲层,得到了高质量的ZnO外延膜.与直接沉积的ZnO膜相比,生长在缓冲层上的ZnO膜展现出规则的斑点状衍射花样,而且拥有更强的UV发射和更窄的UV峰半高宽(98meV).对不同温度下沉积的缓冲层进行了RHEED表征,结果表明,在600～650℃之间生长缓冲层,有望进一步改善ZnO外延膜的质量.     

PLD方法生长ZnO/Si异质外延薄膜的研究

用脉冲激光沉积法在Si(111)衬底上制备了ZnO薄膜。RHEED和XRD测试表明,直接沉积在Si衬底上的ZnO薄膜为多晶薄膜,且薄膜的结晶质量随衬底温度的升高而下降。相比之下,生长在一低温同质缓冲层上的ZnO薄膜则展现出规则的斑点状RHEED图像,说明它们都是外延生长的高质量ZnO薄膜。XRD与室温PL谱分析表明,外延ZnO薄膜的质量随衬底温度的升高得到明显的改善。在650℃生长的样品具有最好的结构和发光特性,其(002)衍射峰的半高宽为0.185°,UV峰的半高宽仅为86meV。     

Zn缓冲层对氧化锌薄膜的结构和光学特性的影响

采用射频磁控溅射法在玻璃衬底上制备了具有高c轴择优取向的不同Zn缓冲层厚度的ZnO(ZnO/Zn)薄膜。利用X射线衍射(XRD)法、扫描电子显微镜(SEM)技术和光致荧光(PL)发光谱(PL)等表征了ZnO/Zn薄膜的微观结构和发光特性。XRD的分析结果显示,随着缓冲层厚度的增加,(002)衍射峰的半高宽(FWHM)逐渐变小,表明薄膜的结晶质量得到改善。通过对样品PL谱的研究,发现分别位于435(2.85eV)和480nm(2.55eV)的蓝光双峰以及530nm(2.34eV)的绿光峰,且缓冲层沉积时间为10min时,样品的单色性最好。推测位于435nm的蓝光发射主要来源于电子从锌填隙缺陷能级到价带顶的跃迁所致,而绿光峰的发光机制与氧空位有关。     

高质量ZnO薄膜的退火性质研究

在LP－MOCVD中，我们利用Zn(C2H5)2作Zn源，CO2作氧源，在（0002）蓝宝石衬底上成功制备出皮c轴取向高度一致的ZnO薄膜，并对其进行500℃-800℃四个不同温度的退火。利用XRD、吸收谱、光致发光谱和AFM等手段研究了退火对ZnO晶体质量和光学性质的影响。退火后，（0002）ZnO的XRD衍射峰强度显著增强，c轴晶格常数变小，同时（0002）ZnOX射红衍射峰半高宽不断减小表明晶粒逐渐增大，这与AFM观察结果较一致。由透射谱拟合得到的光学带隙退火后变小，PL谱的带边发射则加强，并出现红移，蓝带发光被有效抑制，表明ZnO薄膜的质量得到提高。     

PLD生长的ZnO薄膜的微结构及其发光特性研究

在不同的衬底温度下，通过脉冲激光淀积（PLD）方法在Si衬底上生长出c轴高度取向的ZnO薄膜。ZnO薄膜的结构分别通过X射线衍射（XRD）和广延X射线吸收精细结构（EXAFS）来表征，而表面成份和化学态则通过X射线光电子能谱来研究。利用光致发光（PL）来研究样品的发光特性。XRD结果和EXAFS结果都表明了500℃时生长的ZnO薄膜的结晶性比300℃时生长的要好。EXAFS结果和XPS结果显示，300℃时生长的ZnO薄膜处于富氧状态，而500℃时生长的则处于缺氧状态。结合XRD谱、EXAFS谱、XPS谱和PL谱的结果可以看到：随着ZnO薄膜的结晶性变好，它的紫外发光增强；另一方面，随着ZnO薄膜中O的含量减少，绿光发射变强。我们的结果表明绿光发射与ZnO中氧空位（V0）有关。     

热处理温度对溶胶-凝胶法制备ZnO薄膜晶体结构和发光特性的影响

采用溶胶-凝胶(Sol-Gel)旋涂法在Si(100)衬底上制备ZnO薄膜,利用X射线衍射(XRD)、光致发光谱(PL)、扫描电子显微镜(SEM)等手段分析制得的ZnO薄膜的晶体结构和发光特性。着重考察了热分解温度对ZnO薄膜晶体结构和发光特性的影响。结果表明,溶胶-凝胶旋涂法制备的ZnO薄膜样品厚度约为220nm,属六方纤锌矿结构,其c轴取向度与热分解温度有很大关系;ZnO薄膜在室温下均有较强的紫外带边发射峰,且紫外带边发射峰与样品c轴取向度没有直接关系,与缺陷有关的可见发射带很弱。     

MBE法生长ZnO纳米线阵列的结构和光学性能

在氧等离子体辅助的MBE系统中, 以1 nm厚的Au薄膜为催化剂, 基于气?液?固(VLS)机制实现了低温ZnO纳米线阵列在Si(111)衬底表面的生长. 通过场发射扫描电子显微镜(FE-SEM)可以观察到, ZnO纳米线阵列垂直生长在衬底上, 直径为20~30 nm. X射线衍射(XRD)和高分辨透射电镜(HRTEM)结果表明: ZnO纳米线为六方纤锌矿结构, 具有沿c轴方向的择优取向. 光致发光(PL)谱显示在380 nm附近有强烈ZnO本征发射峰, 475~650 nm可见光区域有较强的缺陷导致的发射峰.     

脉冲激光沉积法室温下ZnO薄膜的制备与表征

在室温条件下,采用脉冲激光沉积技术在玻璃衬底上生长了ZnO薄膜.对薄膜的XRD分析表明,ZnO薄膜为六方纤锌矿结构并沿c轴取向生长,且(002)衍射峰的半高峰宽仅为0.24°.薄膜沿c轴方向受到一定的张应力为1.7×108 N/m2.原子力显微镜分析表明薄膜表面较为平整,平均粗糙度约为6.5 nm,晶粒尺寸约为50 nm.此外,透射光谱分析表明薄膜的禁带宽度为3.25 eV,与ZnO体材料的禁带宽度3.30 eV基本相同.     

衬底温度对Mg0.1Zn0.9O薄膜结构及光学性能的影响

利用射频磁控溅射技术在不同温度的(100)Si和玻璃衬底上成功地制备了c轴择优取向的Mg0.1Zn0.9O薄膜.通过X射线衍射(XRD)、场发射扫描电镜(FESEM)、紫外可见光分光光度计和光致发光谱研究了衬底温度对Mg0.1Zn0.9O薄膜结构、表面形貌和光学性能的影响,结果表明,在衬底温度为400℃时生长的Mg0.1Zn0.9O薄膜具有很好的c轴取向和较好的光学性能.用激发波长为300nm的氙灯作为激发光源得到不同衬底温度下Mg0.1Zn0.9O薄膜的室温PL谱.分析表明,紫外发光峰与薄膜的结晶质量密切相关,蓝光发射与氧空位有关.简单探讨了衬底温度影响紫外光致发光峰红移和蓝移的可能机理.     

Estimation of Parameters of Universal Distribution of Moments of Failure of Products

A method is proposed for estimating the parameters of a mixture of exponential and Weibull distributions for which the accuracy of preliminary estimates obtained by graphical analysis is refined in accordance with the criterion of maximum likelihood. The efficiency of the proposed method is supported by the results of statistical modeling.     

Evaluation of optical properties of highly scattering media by moments of distributions of times of flight of photons

A novel method for the determination of the optical properties of tissue from time-domain measurements is presented. The data analysis is based on the evaluation of the first moment and the second centralized moment, i.e., the mean time of flight and the variance of the measured distribution of times of flight (DTOF) of photons injected by short (picosecond) laser pulses. Analytical expressions are derived for calculation of absorption and of reduced scattering coefficients from these moments by application of diffusion theory for infinite and semi-infinite homogeneous media. The proposed method was tested on experimental data obtained with phantoms, and results for absorption and reduced scattering coefficients obtained by the proposed method are compared with those obtained by fitting of the same data with analytical solutions of the diffusion equation. Furthermore, the accuracy of the moment analysis was investigated for a range of integration limits of the DTOF. The moment analysis may serve as a comparatively fast method for evaluating optical properties with sufficient accuracy and can be used, e.g., for on-line monitoring of optical properties of biological tissue.     

Analysis of the rate of propagation of the wave of change of boiling modes

An approximate analytical expression is derived for the velocity of the front of the wave of change of boiling modes on a rod and on a plate. The impact of the Thomson effect and of the heater orientation in the gravity field is included. Adequate agreement is demonstrated between the derived relations and experimental data.     

Estimation of potentialities of methods of summation of direct measurement errors

Conventional methods for summation of direct measurement errors are considered. Conditions under which these methods provide consistent results are stated. It is proposed to utilize for characteristic of the total error, its interval estimator or the half-sum of the value obtained by adding up its arithmetic and geometric random errors.Translated from Izmeritel'naya Tekhnika, No. 4, pp. 10–12, April, 1995.     

空压机轴承箱蜗壳温度探头油封改造

由于空压机进气侧轴承箱蜗壳温度探头密封效果不好,使空压机及其后续管道受到油污染。后将温度探头的O形圈密封改为骨架油封,杜绝了轴承箱漏油问题。文章简介空压机的结构和技术参数,详细介绍了骨架油封的制作和优点。     

Characteristics of mechanical properties of materials in studies of conditions of attainment of marginal states

It is shown that conditions of attainment of marginal states in the material of structural components are formulated on the basis of analysis of force and deformation criteria of formation and development of destruction. The parameters of these criteria are data on types of structural materials, standard and special characteristics of their mechanical properties, structural forms of considered elements of the equipment, and their operating stress loading. In this case, the construction of a system of state equations for describing interrelation of current damage, external actions, and responses to them is based on the concept of calculating variations in properties of materials at all stages of the design life cycle.     

Determination of parameters of microstructural inhomogeneity of deformation of metals by the method of modeling

The article suggests a method of evaluating the microstructural inhomogeneity of deformation of metals by modeling. The method includes the measurement of deformations of metal according to meshes of a dividing grid with small base and the calculation of the distribution parameters of microdeformations in model representation. It is shown that the modeling method makes it possible objectively to evaluate the microinhomogeneity of deformation of metals independently of the chosen mesh size of the dividing grid. New structural characteristics are introduced: the base and wave of variation expressing the degree of crumbling or amalgamation of metal grains by inhomogeneity of deformation.Translated from Problemy Prochnosti, No. 7, pp. 40–44, July, 1991.     

水三相点复现的不确定度评定

水三相点是开尔文热力学温度的唯一基准点，也是ITS-90国际温标重要的定义固定点。因此，水三相点不确定度分析对整个温标的建立、温度量值传递起着至关重要的作用。近3年来，中国计量科学研究院研制出一系列高质量的水三相点容器，加强了水三相点的研究，为不确定度的分析提供了更为可靠的实验依据。同时，不确定度的分析也是客观评价新研制容器性能的一个重要指标。因此，根据实验结果对新研制容器所复现的水三相点进行了不确定度评定。评定结果表明，其扩展不确定度为0．16mK(k=2．69，P=0．99)。