Electrical properties of Au–Sb/p-GaSe:Gd Schottky barrier diode

Experimental results of the fabricated Schottky barrier diode on a GaSe:Gd substrate are presented. The electrical analysis of Au–Sb/p-GaSe:Gd structure has been investigated by means of current–voltage (I–V) and capacitance–voltage (C–V) measurements at 296 K temperature. The diode ideality factor and the barrier height have been obtained to be 1.07 and 0.85 eV, respectively, by applying a thermionic emission theory. At high currents in the forward direction, the series resistance effect has been observed. The series resistance has been determined from I–V measurements using Cheung's method.     

Fabrication and electrical characteristics of Perylene-3,4,9,10-tetracarboxylic dianhydride/p-GaAs diode structure

This study aims to experimentally investigate whether Perylene-3,4,9,10-tetracarboxylic dianhydride (PTCDA) organic layer at p-GaAs/Ag interface affects electrical transport across this interface or not. The electronic properties of metal–organic semiconductor–inorganic semiconductor structure between p type GaAs and PTCDA organic film have been investigated via current–voltage (I–V) and capacitance–voltage (C–V) methods. The Ag/PTCDA/p-GaAs contact exhibits a rectification behavior with the barrier height of 0.74 eV and ideality factor value of 3.42. Modification of the potential barrier of Ag/p-GaAs diode was achieved by using thin interlayer of the PTCDA organic material. This was attributed to the fact that the PTCDA organic interlayer increased the effective barrier height by influencing the space charge region of GaAs. The low and high frequency capacitance–voltage plots were used to determine the interface state density of the diode.     

The effects of thermal annealing on the electrical characteristics of Au/n–InP/In diode

An Au/n–InP/In diode has been fabricated in the laboratory conditions and the current–voltage (I–V) and capacitance–voltage (C–V) characteristics of the diode have been measured in room temperature. In order to observe the effect of the thermal annealing, this diode has been annealed at temperatures 100 and 200 °C for 3 min in N₂ atmosphere. The characteristic parameters such as leakage current, barrier height and ideality factor of this diode have been calculated from the forward bias I–V and reverse bias C–V characteristics as a function of annealing temperature. Also the rectifying ratio of the diode is evaluated for as-deposited and annealed diode.     

Hyperabrupt junctions in Au-Si Schottky diodes by ion implantation

The application of ion implantation to the fabrication of Au-Si Schottky diodes with highly nonlinear capacitance/voltage characteristics is described. The capacitance/voltage characteristic and the derived impurity profile are given for a typical diode. The forward current/voltage characteristics are described, and an estimate of Au-Si barrier height is made.     

Electrical characteristics of rectifying polycrystalline silicon/silicon carbide heterojunctions

This paper presents a study of the rectifying properties of heavily doped polycrystalline silicon (polysilicon) on 4H silicon carbide (4H-SiC). Current properties and barrier heights were found using analysis of the heterojunction. This revealed that Schottky analysis would be valid for the large barrier height devices. Isotype and an-isotype devices were fabricated on both p-type and n-type SiC and the electrical characteristics were investigated using capacitance vs voltage measurements, current vs voltage measurements (I-V), and temperature I-V measurements. Extraction of the barrier height, built-in potential, and Richardson constant were made and then compared to theoretical values for the heterojunction. Temperature I-V measurements demonstrated that the current transport mechanism is thermionic emission, confirming the validity of the Schottky diode model. The I-V characteristics show near ideal diode rectifying behavior and the capacitance-voltage characteristics show ideal junction space charge modulation for all polysilicon/SiC combinations. These experimental results match well with heterojunction band-offset estimated barrier heights and demonstrate that the barrier height of the polysilicon/4H SiC interface may be controlled by varying the polysilicon doping type.     

氮气氛下衬底负偏压预溅射对GaAs肖特基势垒性能的改善

本文研究了不同气氛下衬底负偏压预溅射对GaAs肖特基势垒特性的影响。我们发现,采用氮气氛下衬底负偏压预溅射新工艺能明显改善GaAs肖特基势垒特性:势垒高度增高,势垒电容减小和二极管反向击穿电压增大。这种新工艺对于GaAs肖特基势垒特性改善和GaAs MESFETs性能提高是一个非常有用的技术。     

Numerical simulation study of current–voltage characteristics of a Schottky diode with inverse doped surface layer

The Poisson’s equation and drift–diffusion equations are used to simulate the current–voltage characteristics of Schottky diode with an inverse doped surface layer. The potential inside the bulk semiconductor near the metal–semiconductor contact is estimated by simultaneously solving these equations, and current as a function of bias through the Schottky diode is calculated for various inverse layer thicknesses and doping concentrations. The Schottky diode parameters are then extracted by fitting of simulated current–voltage data into thermionic emission diffusion equation. The obtained diode parameters are analyzed to study the effect of inverse layer thickness and doping concentration on the Schottky diode parameters and its behavior at low temperatures. It is shown that increase in inverse layer thickness and its doping concentration give rise to Schottky barrier height enhancement and a change in the ideality factor. The temperature dependences of Schottky barrier height and ideality factor are studied. The effect of temperature dependence of carrier mobility on the Schottky diode characteristics is also discussed.     

Electrical characterization of inorganic-on-organic diode based InP and poly(3,4-ethylenedioxithiophene)/poly(styrenesulfonate) (PEDOT:PSS)

The electronic properties of metal–organic semiconductor-inorganic semiconductor diode between InP and poly(3,4-ethylenedioxithiophene)/poly(styrenesulfonate) (PEDOT:PSS) polymeric organic semiconductor film have been investigated via current–voltage and capacitance–voltage methods. The Al/PEDOT:PSS/p-InP contact exhibits a rectification behavior with the barrier height value of 0.98 eV and with the ideality factor value of 2.6 obtained from their forward bias current voltage (I–V) characteristics at the room temperature greater than the conventional Al/p-InP (0.83 eV, n = 1.13). This increase in barrier height and ideality factor can be attributed to PEDOT:PSS film formed at Al/p-InP interface.     

Effect of annealing temperature on the electrical characteristics of Platinum/4H-SiC Schottky barrier diodes

Pt/4H-SiC Schottky barrier diodes have been fabricated to investigate the effect of annealing on the electrical characteristics of the fabricated devices. The parameters such as barrier height, ideality factor and donor concentration were deduced from the current–voltage (I–V) and the capacitance–voltage (C–V) measurements at room temperature. Diodes showed non-ideal behaviour like high value of ideality factor and lower value of barrier height. A barrier height of 1.82?eV was obtained from C–V measurements and it was 1.07?eV when obtained from the I–V measurements with ideality factor 1.71 for as-deposited diodes at room temperature. The diodes, therefore, were annealed in the temperature range from 25°C to 400°C to observe the effect of annealing temperature on these parameters. Schottky barrier height and ideality factors were found to be temperature-dependent. After rapid thermal annealing upto 400°C, a barrier height of 1.59?eV from C–V measurements and the value of 1.40?eV from I–V measurements with ideality factor 1.12 were obtained. Barrier heights deduced from C–V measurements were consistently larger than those obtained from I–V measurements. To come to terms with this discrepancy, we re-examined our results by including the effect of ideality factor in the expression of the barrier height. This inclusion of ideality factor results in reasonably good agreement between the values of barrier height deduced by the above two methods. We believe that these improvements in the electrical parameters result from the improvement in the quality of interfacial layer.     

Numerical analysis of inhomogeneous Schottky diode with discrete barrier height patches

The potential profile inside the semiconductor at the metal–semiconductor contact is simulated by numerically solving the Poisson equation and the drift diffusion equations for inhomogeneous Schottky diode. From the simulated potential and the electron and hole concentrations, the drift-diffusion current as a function of bias is calculated. The simulation is carried out for various distribution patterns of barrier height patches at the metal–semiconductor contact to study the effect of barrier inhomogeneities on the Schottky diode parameters, namely barrier height and ideality factor and their temperature dependence. It is found that barrier height decreases and ideality factor increases with increase in the deviation of discrete barrier height patches in the distribution. The resulting barrier parameters are studied to understand the effect of barrier inhomogeneities on the current–voltage characteristics of inhomogeneous Schottky contact.     

Evaluation of the hydrostatic pressure effect on Mn/p-Si Schottky barrier diode electrical parameters and interface states

Mn/p-Si Schottky barrier diode (SBD) electrical parameters and interface state density have been investigated with current–voltage (I–V) characteristics and Cheung's functions employing hydrostatic pressure. The interface state density of the diodes has an exponential growth with bias from the midgap towards the top of the valance band. We have seen that the Schottky barrier height (SBH) for Mn/p-Si SBD has a pressure coefficient of 1.61 meV/kbar (16.1 meV/GPa). We have reported that the p-type barrier height exhibited a weak pressure dependence, accepting that the Fermi level at the interface do not shift as a function of the pressure.     

Characterization of an Au/n-Si photovoltaic structure with an organic thin film

We demonstrate that a copper(II) organic complex can control the electrical characteristics of conventional Au/n-Si metal–semiconductor (MS) contacts. We investigated the electronic and photovoltaic properties of a Cu(II) complex/n-Si heterojunction diode. The ideality factor n and barrier height Φ_b of the diode were 2.22 and 0.736 eV, respectively. An ideality factor greater than unity indicates that the diode exhibits non-ideal current–voltage behavior. This behavior results from the effect of series resistance and the presence of an interfacial layer. The series resistance and barrier height determined using Norde’s method were 6.7 kΩ and 0.77 eV, respectively. The device showed photovoltaic behavior, with a maximum open-circuit voltage of 0.24 V and a short circuit current of 1.7 μA under light of 8 mW/cm².     

A simple model for computer simulation of Schottky-barrier diodes

To simulate the electrical characteristics of metal-semiconductor Schottky barrier diodes, a numerical analysis program based on the Shockley's semiconductor equations has been established. The thermionic emissions of electrons and holes from semiconductor to metal as well as the electric field in the interfacial layer are taken as the derivative boundary conditions of the nonlinear equations. The forward and reverse current-voltage characteristics of various metal-silicon and metal-silicide-silicon Schottky barrier diodes can be simulated by properly choosing the zero-field barrier height and the interfacial-layer capacitance. The barrier height variation as a function of applied voltage is related to the space-charge density and the interfacial-layer capacitance. The nonideality of forward characteristics is attributed to the bending of majority carrier imref and the raising of barrier height. The soft behavior of reverse characteristics can be modeled in terms of the interfacial-layer capacitance.     

Cd1-x Zn x Se thin film electrodes: an electrochemical photovoltaic study

The interface between an n?Cd_1?x Zn _x Se semiconductor and an electrolyte redox couple is investigated through the capacitance–voltage, current–voltage and photovoltaic characteristics. A brief discussion is made on the properties of a semiconductor/electrolyte Schottky barrier with reference to the experiments performed. The observed results of the capacitance–voltage measurements in the dark are compared with the photovoltage measurements. The dependence of the dark current on the dark voltage for both forward and reverse bias is examined and explained. It is probable that the current–voltage characteristics are determined by the electrochemical kinetics in addition to the diode rectifier theory. The measurements of photovoltaic properties show a significant improvement in the cell performance after addition of Zn to CdSe (optimum at x = 0.3).     

Electrical parameters of a DC sputtered Mo/n-type 6H-SiC Schottky barrier diode

A Mo/n-type 6H-SiC/Ni Schottky barrier diode (SBD) was fabricated by sputtering Mo metal on n-type 6H-SiC semiconductor. Before the formation of Mo/n-type 6H-SiC SBD, an ohmic contact was formed by thermal evaporation of Ni on n-type 6H-SiC and annealing at 950 °C for 10 min. It was seen that the structure had excellent rectification. The electrical parameters were extracted using its current–voltage (I–V) and capacitance–voltage (C–V) measurements carried out at room temperature. Very high (1.10 eV) barrier height and 1.635 ideality factor values were reported for Mo/n-type 6H-SiC using ln I–V plot. The barrier height and series resistance values of the diode were also calculated as 1.413 eV and 69 Ω from Norde׳s functions, respectively. Furthermore, 1.938 eV barrier height value of Mo/n-type 6H-SiC SBD calculated from C–V measurements was larger than the one obtained from I–V data.     

Barrier height diminution in Schottky diodes due to electrostatic screening

Electrostatic screening in the metal contact of a Schottky (metal-semiconductor) diode is shown to influence the calculated electrical characteristics of the diode. A thin space-charge layer is formed at the surface of the metal contact by capacitively induced free charges, This results in a voltage dependent diminution of the barrier height of the diode that increases in magnitude with increasing semiconductor dielectric constant and carrier concentration. Predicted values of the barrier height diminution exceed those attributed to image forces or tunneling effects for materials with dielectric constants greater than about 20. In diodes using semiconducting ferroelectric or piezoelectric materials, an additional diminution of the barrier height results from free charges induced in the metal contact by a remanent polarization field or an externally applied mechanical stress. Current-voltage characteristics of a metal-semiconductor diode are shown to be significantly influenced by the electrostatic screening effect. A soft breakdown current as opposed to saturation current is predicted for reverse biases while an exponential forward current with an η coefficient exceeding unity is predicted for forward biases. Photoemission characteristics are also affected. A voltage-dependent diminution of the threshold energy for photoresponse is predicted. Capacitance-voltage characteristics, on the other hand, differ only slightly from those of an ideal Schottky diode except in the case of a ferroelectric diode where excessively large screening effects are possible.     

Effect of Inverse Doped Surface Layer in Schottky Barrier Modification: A Numerical Study

Poisson’s equation and the drift–diffusion equations are used to simulate the current–voltage characteristics of a Schottky diode with an inverse doped surface layer. The potential inside the bulk semiconductor near the metal–semiconductor contact is estimated by simultaneously solving these equations, and then current as a function of bias through the Schottky diode is calculated. The Schottky diode parameters are extracted by fitting of simulated data to the thermionic emission diffusion equation. The simulation is carried out for various inverse layer thicknesses and doping concentrations. The obtained diode parameters are analyzed to study the effect of the inverse layer thickness and doping concentration on Schottky diode modification and its behavior at low temperatures. It is shown that an increase in the inverse layer thickness and doping concentration leads to Schottky barrier height enhancement and a change in the ideality factor. The temperature dependences of the Schottky barrier height and ideality factor are also studied.     

Current–voltage characteristics of Schottky diode simulated using semiconductor device equations

The Poisson's equation and the drift diffusion equations have been used to simulate the current–voltage characteristics of Schottky diode. The potential variation inside the bulk semiconductor near the metal–semiconductor contact was estimated first and then the current as a function of bias through the Schottky diode using silicon parameters were calculated over a wide temperature range. From the simulated current–voltage characteristics the diode parameters were extracted by fitting of current–voltage data into thermionic emission diffusion current equation. The derived barrier parameters are analysed to study the effect of various parameters, e.g. semiconductor thickness, doping concentration, temperature dependence of carrier mobility and energy band gap, on the current–voltage characteristics of Schottky diode in view of the thermionic emission diffusion current equations.     

Temperature-dependence of barrier height of swift heavy ion irradiated Au/n-Si Schottky structure

The electrical characteristics of swift heavy ion (SHI) irradiated Au/n-Si (1 0 0) structure has been investigated in a wide temperature range (50–300 K). The forward bias current–voltage (I–V) measurements have been used to extract the diode parameters as a function of temperature. The Zero-bias Schottky barrier height decreases with decreasing temperature. However, the flat-band barrier height is almost independent of the temperature. These results are interpreted using the models of Fermi level pinning. The behavior of Schottky diode parameters is explained by taking into account the role of the irradiation induced defects at Au/n-Si (1 0 0) interface.     

Determination of the laterally homogeneous barrier height of palladium Schottky barrier diodes on n-Ge (1 1 1)

We have studied the experimental linear relationship between barrier heights and ideality factors for palladium (Pd) on bulk-grown (1 1 1) Sb-doped n-type germanium (Ge) metal-semiconductor structures with a doping density of about 2.5×10¹⁵ cm^?3. The Pd Schottky contacts were fabricated by vacuum resistive evaporation. The electrical analysis of the contacts was investigated by means of current–voltage (I–V) and capacitance–voltage (C–V) measurements at a temperature of 296 K. The effective barrier heights from I–V characteristics varied from 0.492 to 0.550 eV, the ideality factor n varied from 1.140 to 1.950, and from reverse bias capacitance–voltage (C^?2–V) characteristics the barrier height varied from 0.427 to 0.509 eV. The lateral homogenous barrier height value of 0.558 eV for the contacts was obtained from the linear relationship between experimental barrier heights and ideality factors. Furthermore the experimental barrier height distribution obtained from I–V and (C^?2?V) characteristics were fitted by Gaussian distribution function, and their mean values were found to be 0.529 and 0.463 eV, respectively.