Microwave dielectric properties of W-doped Ba0.6Sr0.4TiO3 thin films grown on (001) MgO by pulsed laser deposition with a variable oxygen deposition pressure

The microwave dielectric properties of Ba_0.6Sr_0.4TiO₃ 1 mol% W-doped thin films deposited using pulsed laser deposition, are improved by a novel oxygen deposition profile. The thin films were deposited onto (001) MgO substrates at a temperature of 720 °C. A comparison is made between three different oxygen ambient growth conditions. These include growth at a single oxygen pressure (6.7 Pa) and growth at two oxygen pressures, one low (6.7 Pa) and one high (46.7 Pa). Films were deposited in a sequence that includes both a low to high and a high to low transition in the oxygen deposition pressure. Following deposition, all films were post-annealed in 1 atm of oxygen at 1000 °C for 6 h. The dielectric Q (defined as 1 / tanδ) and the dielectric constant, ε_r, were measured at room temperature, at 2 GHz, using gap capacitors fabricated on top of the dielectric films. The percent dielectric tuning (defined as (ε_r(0 V) − ε_r(40 V)) / ε_r(0 V) × 100) and figure of merit (FOM) (defined as percent dielectric tuning × Q(0 V)) were calculated. The film deposited using the two-stage growth conditions, 6.7 / 46.7 Pa oxygen, showed a maximum Q(0 V) value with high percent dielectric tuning and gave rise to a microwave FOM twice as large as the single stage growth condition. The improved dielectric properties are due to initial formation of a film with reduced interfacial strain, due to the formation of defects at the film/ substrate interface resulting in a high Q(0 V) value, followed by the reduction of oxygen vacancies which increases the dielectric constant and tuning.     

Deposition of Sm2O3 doped CeO2 thin films from Ce(DPM)4 and Sm(DPM)3 (DPM=2,2,6,6-tetramethyl-3,5-heptanedionato) by aerosol-assisted metal–organic chemical vapor deposition

Samarium-doped ceria (SDC) thin films were prepared from Sm(DPM)₃ (DPM = 2,2,6,6-tetramethyl-3,5-heptanedionato) and Ce(DPM)₄ using the aerosol-assisted metal–organic chemical vapor deposition method. -Al₂O₃ and NiO-YSZ (YSZ = Y₂O₃-stabilized ZrO₂) disks were chosen as substrates in order to investigate the difference in the growth process on the two substrates. Single cubic structure could be obtained on either -Al₂O₃ or NiO-YSZ substrates at deposition temperatures above 450 °C; the similar structure between YSZ and SDC results in matching growth compared with the deposition on -Al₂O₃ substrate. A typical columnar structure could be obtained at 650 °C on -Al₂O₃ substrate and a more uniform surface was produced on NiO-YSZ substrate at 500 °C. The composition of SDC film deposited at 450 °C is close to that of precursor solution (Sm : Ce = 1 : 4), higher or lower deposition temperature will both lead to sharp deviation from this elemental ratio. The different thermal properties of Sm(DPM)₃ and Ce(DPM)₄ may be the key reason for the variation in composition with the increase of deposition temperature.     

Effect of copper-oxide segregation on the dielectric properties of CaCu3Ti4O12 thin films fabricated by pulsed-laser deposition

We investigated the effects of post-deposition cooling conditions on the surface morphologies and dielectric properties of CaCu₃Ti₄O₁₂ (CCTO) thin films grown by pulsed-laser deposition on Pt/TiO₂/SiO₂/Si substrates. CCTO thin films cooled under the typical cooling parameters, i.e., slow cooling (3 °C/min) at high oxygen pressure (66 kPa) showed a severe segregation of nanoparticles near the grain boundaries, which was identified to be copper oxide from electron probe micro analyzer mapping. On the other hand, we could not observe any segregation on the film surface when the samples were cooled fast (∼ 20 °C/min) at relatively low oxygen pressure (100 Pa). The dielectric constant, ε_r, of CCTO thin films deposited at 750 °C with severe surface segregation (ε_r ∼ 750 at 10 kHz) was found to be much lower than that (ε_r ∼ 2000 at 10 kHz) of CCTO thin films with smooth surface. As the copper-oxide segregation becomes more serious, which preferentially occurs at relatively high ambient oxygen pressure and temperature, the degradation in the dielectric properties of CCTO films becomes larger. The variation of dielectric constant of CCTO films with no copper-oxide segregation could be related to the presence of an impurity phase at grain boundaries.     

Direct liquid injection metal-organic chemical vapor deposition of HfO2 thin films using Hf(dimethylaminoethoxide)4

Hf(OCH₂CH₂NMe₂)₄, [Hf(dmae)₄] (dmae=dimethylaminoethoxide) was synthesized and used as a chemical vapor deposition precursor for depositing Hf oxide (HfO₂). Hf(dmae)₄ is a liquid at room temperature and has a moderate vapor pressure (4.5 Torr at 80 °C). It was found that HfO₂ film could be deposited as low as 150 °C with carbon level not detected by X-ray photoelectron spectroscopy. As deposited film was amorphous but when the deposition temperature was raised to 400 °C, X-ray diffraction pattern showed that the film was polycrystalline with weak peak of monoclinic (020). Scanning electron microscope analysis indicated that the grain size was not significantly changed with the increase of the annealing temperature. Capacitance–voltage measurement showed that with the increase of annealing temperature, the effective dielectric constant was increased, but above 900 °C, the effective dielectric constant was decreased due to the formation of interface oxide. For 500 Å thin film, the dielectric constant of HfO₂ film annealed at 800 °C was 20.1 and the current–voltage measurements showed that the leakage current density of the HfO₂ thin film annealed at 800 °C was 2.2×10⁻⁶ A/cm² at 5 V.     

Structure and conducting properties of La0.5Sr0.5CoO3−δ films on YSZ

La_0.5Sr_0.5CoO_3−δ (LSCO) thin films were deposited on yttria stabilized zirconia (YSZ) substrates by pulsed laser deposition (PLD) for application to thin film solid oxide fuel cell electrodes. During the deposition, the substrate temperature was varied from 450 to 750°C, and the oxygen pressure in the chamber was varied from 80 to 310 mTorr. Films deposited at 650°C and an oxygen background pressure of 150 mTorr were mostly (100) oriented. Deposition at higher temperatures or under lower oxygen pressures lead to mostly (110) oriented films. Films with low electrical resistivity of 10⁻³ Ω·cm were obtained.     

Characterization of activated reactive evaporated MoO3 thin films for gas sensor applications

Thin films of molybdenum trioxide (MoO₃) were prepared by activated reactive evaporation technique on Pyrex glass substrates. The influence of oxygen partial pressure, substrate temperature and glow power on the structure, surface morphology and optical properties of MoO₃ thin films was studied. The MoO₃ films deposited in an oxygen partial pressure of 1×10⁻³ Torr, glow power of 10 W and substrate temperature of 573 K exhibited predominantly a (0 k 0) orientation corresponding to the orthorhombic layered structure of -MoO₃. The evaluated optical band gap was 3.24 eV. The sensing property of these MoO₃ films for gases like NH₃ and CO was also studied to see the applicability for environmental monitoring. We have observed that the MoO₃ thin films of -phase are capable of detecting NH₃ and CO gases at concentrations lower than 10 ppm in dry air.     

Electrical characterization of Ta2O5 films deposited by laser reactive ablation of metallic Ta

Tantalum oxide films have been deposited by 355 nm pulsed laser ablation of metallic Ta target in O₃/O₂ ambient. The structure and the composition of as-deposited and annealed films were examined by X-ray diffraction and Fourier transform infrared spectroscopy. The measurements of the current–voltage and capacitance–voltage characteristics of the Al/Ta₂O₅/Si capacitors were performed to reveal the electrical properties of the Ta₂O₅ films. The effects of annealing temperature on the characteristics of thin films have been studied. The results suggest that the films annealed above 700°C have the structure of orthorhombic β-Ta₂O₅, thc annealing treatment at high temperature decreases the bulk trap charge, the border trap, and the interface trap densities of as-deposited films, and improves significantly the dielectric and electrical properties of Ta₂O₅ film.     

Structural, electrical, and optical studies on rapid thermally processed ferroelectric BaTiO3 thin films prepared by metallo-organic solution deposition technique

Polycrystalline BaTiO₃ thin films having the perovskite structure were successfully produced on platinum coated silicon, bare silicon, and fused quartz substrate by the combination of the metallo-organic solution deposition technique and post-deposition rapid thermal annealing treatment. The films exhibited good structural, electrical, and optical properties. The electrical measurements were conducted on metal-ferroelectric-metal (MFM) and metal-ferroelectric-semiconductor (MFS) capacitors. The typical measured small signal dielectric constant and dissipation factor at a frequency of 100 kHz were 255 and 0.025, respectively, and the remanent polarization and coercive field were 2.2 μC cm⁻² and 25 kV cm⁻¹, respectively. The resistivity was found to be in the range 10¹⁰–10¹² Ω·cm, up to an applied electric field of 100 kV cm⁻¹, for films annealed in the temperature range 550–700 °C. The films deposited on bare silicon substrates exhibited good film/substrate interface characteristics. The films deposited on fused quartz were highly transparent. An optical band gap of 3.5 eV and a refractive index of 2.05 (measured at 550 nm) was obtained for polycrystalline BaTiO₃ thin film on fused quartz substrate. The optical dispersion behavior of BaTiO₃ thin films was found to fit the Sellmeir dispersion formula well.     

Al2O3 formation on Si by catalytic chemical vapor deposition

Catalytic chemical vapor deposition (Cat-CVD) has been developed to deposit alumina (Al₂O₃) thin films on silicon (Si) crystals using N₂ bubbled tri-methyl aluminum [Al(CH₃)₃, TMA] and molecular oxygen (O₂) as source species and tungsten wires as a catalyzer. The catalyzer dissociated TMA at approximately 600 °C. The maximum deposition rate was 18 nm min⁻¹ at a catalyzer temperature of 1000 °C and substrate temperature of 800 °C. Metal oxide semiconductor (MOS) diodes were fabricated using gates composed of 32.5-nm-thick alumina film deposited at a substrate temperature of 400 °C. The capacitance measurements resulted in a relative dielectric constant of 7.4, fixed charge density of 1.74×10¹² cm⁻², small hysteresis voltage of 0.12 V, and very few interface trapping charges. The leakage current was 5.01×10⁻⁷ A cm⁻² at a gate bias of 1 V.     

Characterization of indium zinc oxide thin films prepared by pulsed laser deposition using a Zn3In2O6 target

Using a Zn₃In₂O₆ target, indium-zinc oxide films were prepared by pulsed laser deposition. The influence of the substrate deposition temperature and the oxygen pressure on the structure, optical and electrical properties were studied. Crystalline films are obtained for substrate temperatures above 200°C. At the optimum substrate deposition temperature of 500°C and the optimum oxygen pressure of 10⁻³ mbar, both conditions that indeed lead to the highest conductivity, Zn₃In₂O₆ films exhibit a transparency of 85% in the visible region and a conductivity of 1000 S/cm. Depositions carried out in oxygen and reducing gas, 93% Ar/7% H₂, result in large discrepancies between the target stoichiometry and the film composition. The Zn/In (at.%) ratio of 1.5 is only preserved for oxygen pressures of 10⁻²–10⁻³ mbar and a 93% Ar/7% H₂ pressure of 10⁻² mbar. The optical properties are basically not affected by the type of atmosphere used during the film deposition, unlike the conductivity which significantly increases from 80 to 1400 S/cm for a film deposited in 10⁻² mbar of O₂ and in 93% Ar/7% H₂, respectively.     

SnO2:Ga thin films as oxygen gas sensor

Ga-doped SnO₂ thin films deposited by spray pyrolysis were investigated as oxygen gas sensors. Gallium was added to the films to enhance the catalytic activity of the surface’s film to oxygen. Film resistance was studied in an environment of dry air loaded with oxygen in excess at partial pressures in the range from 0 to 8.78×10³ Pa. The best sensitivity lies close to partial pressures of 133.3 Pa. Film sensitivity reach a maximum at 350 °C. For this temperature and a doping concentration of 3 at.% of Ga in the starting solution, a sensitivity up to 2.1 was obtained.     

Structural and optical properties of pulsed laser deposited V2O5 thin films

Pulsed laser deposited nanocrystalline V₂O₅ thin films were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), high-resolution transmission electron microscopy (HRTEM) and optical spectroscopy. The films were deposited on amorphous glass substrates, keeping the O₂ partial pressure at 13.33 Pa and the substrate temperature at 220 °C. The characteristics of the films were changed by varying the laser fluence and repetition rate. XRD revealed that films are nanocrystalline with an orthorhombic structure. XPS shows the sub-stoichiometry of the films, that generally relies on the fact that during the formation process of V₂O₅ films, lower valence oxides are also created. From the HRTEM images, we observed the size evolution and distribution characteristics of the clusters in the function of the laser fluence. From the spectral transmittance we determined the absorption edge using the Tauc plot. Calculation of the Bohr radius for V₂O₅ is also reported.     

(Fe,Ti) 16N2 films with high saturation magnetization prepared by facing target sputtering

(Fe,Ti)-N films with a Ti concentration of 10 at.% were prepared on Si(100) and NaCl substrates by facing targets sputtering. The effects of the nitrogen pressure (P_N) and the substrate temperature (T_s) on the formation of various (Fe,Ti)-N phases and their microstructures were investigated in detail. X-ray diffractometer and transmission electron microscope provided complete identification of the phases present in the films and the characterization of their microstructures. Films deposited at a lower P_N = 1 3 × 10⁻² Pa or a lower T_s = RT consist of mainly -phase. Films deposited at a higher P_N = 1.3 2 × 10⁻¹ Pa or a higher T_s = 200 °C contain a great many γ' and Fe₂N phases with a higher nitrogen content. When P_N = 4 7 × 10⁻² Pa and T_s = 100 150 °C, it is advantageous to the formation of ′' phase. These films exhibit a high saturation magnetization (M_s) up to the range of 2.3 2.5 T, which is larger than that of pure iron.     

Epitaxial growth of RuO2 thin films by metal-organic chemical vapor deposition

Conductive RuO₂ thin films were epitaxially grown on LaAlO₃(100) and MgO(100) substrates by metal-organic chemical vapor deposition (MOCVD). The deposited RuO₂ films were crack-free, and well adhered to the substrates. The RuO₂ film is (200) oriented on LaAlO₃ (100) substrates at deposition temperature of 600°C and (110) oriented on MgO(100) substrates at deposition temperature of 350°C and above. The epitaxial growth of RuO₂ on MgO and LaAlO₃ is demonstrated by strong in-plane orientation of thin films with respect to the major axes of the substrates. The RuO₂ films on MgO(100) contain two variants and form an orientation relationship with MgO given by RuO₂(110)//MgO(100) and RuO₂[001]//MgO[011]. The RuO₂ films on LaAlO₃(100), on the other hand, contain four variants and form an orientation relationship with LaAlO₃ given by RuO₂(200)//LaAlO₃(100) and RuO₂[011]//LaAlO₃[011]. Electrical measurements on the RuO₂ thin films deposited at 600°C show room-temperature resistivities of 40 and 50 μΩ cm for the films deposited on the MgO and LaAlO₃ substrates, respectively.     

Comparative analysis for the crystalline and ferroelectric properties of Pb(Zr,Ti)O3 thin films deposited on metallic LaNiO3 and Pt electrodes

The crystalline quality and ferroelectricity of the Pb(Zr,Ti)O₃ (PZT) films deposited on the metallic LaNiO₃ (LNO) and Pt electrodes were comparatively analyzed to investigate the possibility for their application to non-volatile memory devices. LNO thin films were successfully deposited on various substrates by using r.f. magnetron sputtering even at a low temperature ranging from 250 to 500 °C, and the ferroelectric PZT thin films were spin-coated onto the LNO and Pt bottom electrodes. Metallic LNO thin films exhibited [100] orientation irrespective of the substrate species and PZT films coated onto LNO films had highly a- and c-axis orientations, while those with Pt bottom electrode were polycrystalline. PZT films with LNO bottom electrode had smaller grain size and larger dielectric constant compared to those grown on the Pt electrode. The ferroelectric thin films fabricated on LNO bottom electrode displayed an asymmetric D–E hysteresis loop, which was explained by the defect effects formed at the interface. Especially, the LNO/PZT/LNO capacitor was found to significantly improve the polarization fatigue and the effects of the LNO electrodes to the fatigue were discussed.     

Deposition and dielectric properties of CaCu3Ti4O12 thin films deposited on Pt/Ti/SiO2/Si substrates using radio frequency magnetron sputtering

Polycrystalline CaCu₃Ti₄O₁₂ thin films were deposited on Pt(111)/Ti/SiO₂/Si substrates using radio frequency magnetron sputtering. The phase formation and the physical quality of the films were crucially dependent on the substrate temperature and oxygen partial pressure. Good quality films were obtained at a substrate temperature of 650 °C and 4.86 Pa total pressure with 1% O₂. The dielectric constant (∼ 5000 at 1 kHz and 400 K) of these films was comparable to those obtained by the other techniques, eventhough, it was much lower than that of the parent polycrystalline ceramics. For a given temperature of measurements, dielectric relaxation frequency in thin film was found to be much lower than that observed in the bulk. Also, activation energy associated with the dielectric relaxation for the thin film (0.5 eV) was found to be much higher than that observed in the bulk ceramic (0.1 eV). Maxwell-Wagner relaxation model was used to explain the dielectric phenomena observed in CaCu₃Ti₄O₁₂ thin films and bulk ceramics.     

Transparent conducting F-doped SnO2 thin films grown by pulsed laser deposition

Transparent conducting fluorine-doped tin oxide (SnO₂:F) films have been deposited on glass substrates by pulsed laser deposition. The structural, electrical and optical properties of the SnO₂:F films have been investigated as a function of F-doping level and substrate deposition temperature. The optimum target composition for high conductivity was found to be 10 wt.% SnF₂ + 90 wt.% SnO₂. Under optimized deposition conditions (T_s = 300 °C, and 7.33 Pa of O₂), electrical resistivity of 5 × 10^− 4 Ω-cm, sheet resistance of 12.5 Ω/□, average optical transmittance of 87% in the visible range, and optical band-gap of 4.25 eV were obtained for 400 nm thick SnO₂:F films. Atomic force microscopy measurements for these SnO₂:F films indicated that their root-mean-square surface roughness ( 6 Å) was superior to that of commercially available chemical vapor deposited SnO₂:F films ( 85 Å).     

Structural, optical and electrical characterization of spray-deposited TiO2 thin films

Titanium oxide (TiO₂) thin films were deposited onto glass substrates by means of spray pyrolysis method using methanolic titanyl acetyl acetonate as precursor solution. The thin films were deposited at three different temperatures namely 350, 400 and 450 °C. As-deposited thin films were amorphous having 100–300 nm thickness. The thin films were subsequently annealed at 500 °C in air for 2 h. Structural, optical and electrical properties of TiO₂ thin films have been studied. Polycrystalline thin films with rutile crystal structure, as evidenced from X-ray diffraction pattern, were obtained with major reflexion along (1 1 0). Surface morphology and growth stages based on atomic force microscopy measurements are discussed. Electrical properties have been studied by means of electrical resistivity and thermoelectric power measurements. Optical study shows that TiO₂ possesses direct optical transition with band gap of 3.4 eV.     

Structure and electrical properties of (100)-oriented Pb(Zn1/3Nb2/3)O3–Pb(Mg1/3Nb2/3)O3–PbTiO3 thin films on La0.7Sr0.3MnO3 electrode by chemical solution deposition

(100)-oriented 0.462Pb(Zn_1/3Nb_2/3)O₃–0.308Pb(Mg_1/3Nb_2/3)O₃–0.23PbTiO₃ (PZN-PMN-PT) perovskite ferroelectric thin films were prepared on La_0.7Sr_0.3MnO₃/LaAlO₃ (LSMO/LAO) substrate via a chemical solution deposition route. The perovskite LSMO electrode was found to effectively suppress the pyrochlore phase while promote the growth of the perovskite phase in the PZN-PMN-PT film. The film annealed at 700 °C exhibited a high dielectric constant of 2130 at 1 kHz, a remnant polarization, 2P_r, of 29.8 μC/cm², and a low leakage current density of 7.2 × 10^− 7 A/cm² at an applied field of 200 kV/cm. The ferroelectric polarization was fatigue-free at least up to 10¹⁰ cycles. Piezoelectric coefficient, d₃₃, of 48 pm/V was also demonstrated. The results showed that much superior properties could be achieved with the PZN-PMN-PT thin films on the solution derived LSMO electrode than on Pt electrode by sputtering.     

Preparation of highly c-axis-oriented Bi4Ti3O12 thin films and their crystallographic, dielectric and optical properties

Bismuth titanate (Bi₄Ti₃O₁₂) thin films with a high c-axis orientation up to 99% were prepared on (100)-oriented silicon wafers by r.f. planar magnetron sputtering using a Bi₂TiO₅ ceramic target at a substrate temperature of 600 °C. From the Auger electron spectroscopy depth profile of the film, there is no evidence of interdiffusion of a specific element between the film and the substrate. Relative dielectric constant of these films depends on film thickness. The behavior was explained assuming a low-dielectric-constant interface layer. Using this assumption, the relative dielectric constant of Bi₄Ti₃O₁₂ film was estimated to be approximately 140. This value is close to that along the c axis in a bulk form. The remanent polarization and the coercive field were 0.8 μC cm⁻² and 20 kV cm⁻¹, respectively.