Morphology development by reactive compatibilisation and dynamic vulcanisation of nylon6/EPDM blends with a high rubber fraction

Binary nylon6/rubber blends with 50 or 60 weight percent of an EPDM rubber exhibit co-continuous morphologies and thereby relatively poor mechanical properties. This paper describes methods to develop nylon6/EPDM blends with a high amount of finely dispersed rubber particles embedded in a nylon matrix. Using a suitable compatibiliser and by slightly crosslinking the rubber phase during melt-mixing, it was possible to disperse up to 60 wt% rubber in the nylon matrix and to improve the mechanical properties markedly. These materials are called thermoplastic vulcanisates and exhibit good elastic properties with a thermoplastic processability. The influence of the compatibiliser, the crosslinking agent and the viscosity ratio rubber/thermoplastic on the blend phase morphology is investigated using transmission electron microscopy. It was found that the viscosity ratio rubber/nylon plays a crucial role in order to achieve a nylon6/rubber TPV with a fine rubber dispersion. The viscosity of the nylon phase should be low enough to shift the phase inversion towards higher rubber content. On the other hand, if the viscosity of the nylon is too low, a coarse blend morphology was achieved resulting in poor mechanical properties.     

Dynamic vulcanization of recycled milk pouches (LDPE–LLDPE) and EPDM blends using dicumyl peroxide

The viability of thermomechanical recycling of post‐consumer milk pouches (blend of low‐density polyethylene (LDPE) and linear low‐density polyethylene (LLDPE)) and its scope for suitable engineering applications were investigated. The effects of blending with ethylene‐propylene‐diene monomer (EPDM) rubber and subsequent curing using dicumyl peroxide (DCP) on the macromolecular structure and properties of recycled polyethylene (PE) blends were studied. The crosslinking efficiency of recycled PE/EPDM blends and possible thermooxidative degradation of recycled polymer upon peroxide curing was assessed using torque and gel content measurements along with infrared spectroscopic analysis. Both the torque and gel content of the blends varied with DCP crosslinking reactions and also were affected by oxidative degradation. In view of the electrical application area of this recycled blend material, the dielectric breakdown strength and volume resistivity were measured. The mechanical performance and thermal stability of recycled PE/EPDM blends improved with progressive crosslinking by DCP but deteriorated somewhat at higher DCP dose. Scanning electron microscopy showed good interface bonding between recycled polymer and dispersed EPDM phase in the cured blends compared to the non‐cured blends. Copyright © 2007 Society of Chemical Industry     

Scale effects upon morphology development during mix melting of multiphase polymer blends in ZSK extruders

Replicate experiments were performed on ZSK-30 and ZSK-40 split barrel extruders concerning structure developments from PS-PE pellet blends during the melting process. PS is the minor phase. PE grades were choosen to accommodate viscous and thin matrix phase viscosities. The large extruder displays a more diverse cross channel structure and retarded phase development for some blends. Inferior dispersion is especially obvious in the larger extruder when processing low viscosity matrix blends. Similar phase development occurs in the extruders for high viscosity matrix blends.     

Thermal and mechanical properties of uncrosslinked and chemically crosslinked polyethylene/ethylene vinyl acetate copolymer blends

Uncrosslinked and chemically crosslinked binary blends of low‐ and high‐density polyethylene (PE), with ethylene vinyl acetate copolymer (EVA), were prepared by a melt‐mixing process using 0–3 wt % tert‐butyl cumyl peroxide (BCUP). The uncrosslinked blends revealed two distinct unchanged melting peaks corresponding to the individual components of the blends, but with a reduced overall degree of crystallinity. The crosslinking further reduced crystallinity, but enhanced compatibility between EVA and polyethylene, with LDPE being more compatible than HDPE. Blended with 20 wt % EVA, the EVA melting peak was almost disappeared after the addition of BCUP, and only the corresponding PE melting point was observed at a lowered temperature. But blended with 40% EVA, two peaks still existed with a slight shift toward lower temperatures. Changes of mechanical properties with blending ratio, crosslinking, and temperature had been dominated by the extent of crystallinity, crosslinking degree, and morphology of the blend. A good correlation was observed between elongation‐at‐break and morphological properties. The blends with higher level of compatibility showed less deviation from the additive rule of mixtures. The deviation became more pronounced for HDPE/EVA blends in the phase inversion region, while an opposite trend was observed for LDPE/EVA blends with co‐continuous morphology. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3261–3270, 2007     

Reactive processing of polyethylene and polyethylene–ethylene/propylene/dicyclopentadiene blends under static and dynamic conditions

Abstract

Dicumyl peroxide induced reactive melt processing of polyethylene (PE) in a shear mix at 170°C in the absence or presence of selected acrylic monomers (acrylic acid, ethyl acrylate, and butyl acrylate) has been studied. The acrylic graft copolymers of PE showed development of higher shear stress compared with the control PE when studied rheologically in a plate and cone viscometer at 160–190°C. All the modified PE products retained the pseudoplastic flow behaviour of PE. Measure of rupture shear parameters and of thixotropic and relaxation behaviour of the different modified PEs and of the control PE were also evaluated and compared. The observed effects and unexpected trends were analysed and interpreted.

The comparative effects of sulphur vulcanisation of polyethylene–ethylene/propylene/dicyclopentadiene terpolymer (PE–EPDM) blends by static and dynamic techniques were also studied using both a conventional curative system and a silane curative system. Rheometric studies indicated development of a co-continuous phase morphology for the 30/70 PE–EPDM blend. For a given blend, cured under given conditions, tensile strength and elongation at break at 25°C were higher for vulcanisates obtained statically than for those obtained dynamically, while the corresponding modulus values followed the opposite trend. The conventional curative usually cured at a higher rate. The property differences from static and dynamic vulcanisation are explained in the light of the differences in the developed morphology.     

Effect of some curatives on the properties of ethylene propylene diene rubber/polyethylene blends

A series of ethylene propylene diene rubber/polyethylene (EPDM/PE) blends has been prepared containing different weight fractions of PE up to 0.66. The blends were vulcanized with a sulphur system N-cyclohexyl-2-benzthiazol sulphenamide/sulphur (CBS/S), and a non-sulphur-system dicumyl peroxide (DCUP). The concentration of the latter has been changed from 1.5 phr up to 6 phr calculated on the total weight of the blend composition. It has been found that the maximum torque obtained from rheographs for blends vulcanized with the CBS/S system decreases markedly with increasing PE concentration in comparison with those vulcanized with peroxide. The E modulus obtained from the stress–strain diagram at 110 °C showed the role played by the crosslinking of PE, the E modulus for blends vulcanized by peroxide being higher than for samples vulcanized with CBS/S. In contrast, the values of E modulus of both samples are practically the same at room temperature and attain more than 40 MPa depending on the composition. The tensile strength at room temperature strongly increases with increasing the weight fraction of PE. It has also been confirmed that the melting point of the crystalline phase of PE decreases with increasing crosslinking density of PE. The shear modulus obtained from dynamic mechanical measurements is in accordance with that obtained from static mechanical measurements. © 1999 Society of Chemical Industry     

Morphologies of polyethylene–ethylene/propylene/diene monomer particles in polypropylene‐rich polyolefin blends: Flake structure

Morphologies of polyethylene–ethylene/propylene/diene monomer (PE/EPDM) particles in 93/7 polypropylene (PP)/PE blends were investigated. SEM micrographs of KMnO₄‐etched cut surfaces and fracture surfaces of the blends revealed the existence of the “flake” structure. In the particles, crystalline PE formations with flake shape, which remain after etching, are called flakes. In addition to the PE‐crystalline flakes, amorphous PE, located between PE crystalline lamellae and EPDM rubber, complement the flake structure. The flakes are usually linked with the PP matrix, as seen in the heptane‐treated cut surfaces. These links, although observed with compatibilized samples, originate from the crystalline nature of PE particles, if no compatibilizer is added. Separately, the morphology of Royalene (consisting of high‐density PE and EPDM rubber, used as a PP/PE compatibilizer) was investigated by low‐voltage scanning TEM. The interaction of the components in the PE/EPDM blends can explain the formation of the flakes and toughening of the PP/PE blends. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3087–3092, 2003     

Compatibilizing effect of EPM-g-MA in EPDM/poly(trimethylene terephthalate) incompatible blends

The morphology of immiscible and highly incompatible blends of Sorona^® polymer [Poly(trimethylene terephthalate), PTT] and ethylene propylene diene rubber (EPDM) blends has been studied with and without the addition of a compatibilizer precursor EPM-g-MA. These incompatible blends are characterized by a two-phase morphology, narrow interphase, and poor physical and chemical interactions across the phase boundaries. Therefore, a reactive route was employed to compatibilize these blends by the addition of maleic anhydride grafted ethylene propylene rubber (EPM-g-MA). The blends were prepared in an internal mixer. The morphology was examined by scanning electron microscopy (SEM) after preferential extraction of the minor phase. The SEM micrographs were quantitatively analyzed for domain size measurements. The morphology of the blends indicated that the EPDM phase was preferentially dispersed as domains in the continuous Sorona^® matrix up to 30% of its concentration. A co-continuous morphology was observed above 30 wt% of EPDM content followed by a phase inversion beyond 60 wt% of EPDM. The influence of EPM-g-MA on the phase morphology of blends was studied quantitatively by SEM. It was found that the addition of EPM-g-MA reduces the domain size of the dispersed phase followed by a leveling off at higher concentrations of the compatibilizer. This is an indication of interfacial saturation. The experimental compatibilization results were compared with theoretical predictions. The conformation of the compatibilizer at the interface was analyzed based on the area occupied by the compatibilizer at the blend interface. Free volume measurements using positron annihilation lifetime spectroscopy (PALS) were done to analyze the interaction of blends. In the case of uncompatibilized blends the free volume values tend to increase by the addition of EPDM phase showing high level of incompatibility. Addition of EPM-g-MA to the blends tends to decrease the free volume showing its compatibilizing effect.     

Viscosity effect in polyolefin ternary blends and composites

Ternary blends of PP (80) /rubber (EPM, EPDM) (10) / PE (10) and PP (80) / rubber (10) / CaCO₃ (10) composites were prepared in a twin-screw extruder. With polyethylene (PE) viscosity comparable to, or higher than that of rubber, the dispersed phase formed a reticulate structure with reduced size. On the contrary, when the viscosity of PE was significantly lower than that of rubber, the dispersed phase formed almost homogeneous morphology. With reticulate morphology, PE crystallinity content, hardness, modulus, and elongation at break of the ternary blend increased. In polypropylene (PP) / rubber / CaCO₃ composites, better dispersion of CaCO₃ in the PP matrix was obtained when the viscosity of rubber was significantly higher than that of matrix. With better dispersion, hardness and tensile properties were improved, but the impact strength more or less decreased. © 1993 John Wiley & Sons, Inc.     

基体性质对聚丙烯力学性能的影响

采用过氧化二异丙苯(DCP)作为降解剂,以聚丙烯(PP)为基体,以三元乙丙橡胶(EPDM)为增韧剂,研究了EPDM对降解PP/EPDM共混物力学性能的影响,并利用扫描电子显微镜(SEM)对共混体系微观形貌进行了表征。熔体质量流动速率结果表明:随着EPDM质量分数从10%增加到30%时,对应共混物的熔体质量流动速率明显下降,从14.8 g/10 min下降到10.8 g/10 min。随着EPDM用量的增加,共混物的冲击强度明显增大,从30.06J/m增长到90.26 J/m,拉伸强度有所减小。SEM照片显示,随着EPDM用量的增加,共混物中分散相的尺寸明显增大。因为EPDM含量的增加,导致分散的橡胶粒子产生"聚并",从而分散相的相区尺寸增大。     

Dynamic properties of rubber vibration isolators and antivibration performance of ethylene–propylene–diene monomer/nylon 6 blend systems

This article examines thermoplastic elastomers (TPEs) and thermoplastic vulcanizates (TPVs) as two types of elastomers from melt-blended and dynamically vulcanized ethylene–propylene–diene monomer (EPDM) rubber materials and nylon 6 plastic materials. A series of investigations were conducted on the mechanical properties, morphology, dynamic mechanical properties, hysteresis behavior, and dynamic antivibration properties with different nylon 6 contents. The experimental results showed that the incompatibility between EPDM and nylon 6 led to the easy destruction of the TPV materials in two interfacial polymers upon the application of an external force. Thus, after a dynamic vulcanization process, the mechanical properties of the EPDM/nylon 6 blends were not as good as those of the TPE materials. In terms of morphology, nylon 6 plastics were uniformly distributed in the EPDM/nylon 6 blends during the EPDM rubber phase before vulcanization was performed. After the dynamic vulcanization, phase inversion was produced in which rubber microparticles were formed and dispersed in the nylon 6 plastic phase. The results of dynamic mechanical analysis, compression vibration hysteresis behavior, and dynamic property antivibration experiments showed that the blends provided better vibration isolation and antivibration performance after the amount of nylon 6 was increased and EPDM and nylon 6 were blended through dynamic vulcanization. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Toward Largely Enhanced Toughness and Balanced Strength in PA1012/EPDM Blends via Synergistic Effect of Sacrificial Bonds and Network Structure

Here, zinc-neutralized ethylene propylene diene monomer (EPDM) ionomers with different neutralization levels are prepared through melt blending, and are then incorporated with polyamide 1012 (PA1012) to fabricate PA1012/EPDM ionomer blends. Interestingly, complex crosslinking networks are formed in the blends due to the construction of sacrificial bonds (Zn²⁺-carboxyl, Zn²⁺-amide). The as-formed network structure and sacrificial bond endow the PA/EPDM blends with largely enhanced toughness (16 times higher than that of neat PA), as well as balanced strength and stiffness. Meanwhile, the rheological behaviors of PA1012/EPDM ionomer blends indicate their relative low melting viscosity, which can avoid the processing shortcomings of plastics toughened with rubber. Moreover, PA1012/EPDM ionomer blends show obvious gelation behavior, and a maximum notched Izod impact strength exhibited at the gel point, in which unique double network structure can be observed obviously, indicating that there is a corresponding correlation between the rheological and mechanical parameters. Furthermore, the supper-toughening mechanism of PA1012/EPDM ionomer blends at gel point is explored, which origins from the large deformation and cavitation of rubber particles and the destruction of special double network morphologies. This study provides a novel and effective strategy to fabricate PA materials with outstanding toughness and excellent strength simultaneously.     

The Effect of Dicumyl Peroxide Vulcanization on the Properties & Morphology of Polypropylene/Ethylene-Propylene Diene Terpolymer/Natural Rubber Blends

ABSTRACT

This article discusses some properties such as tensile properties, chemical and oil resistance, gel content, crystallinity, and morphology of polypropylene (PP)/ethylene-propylene diene terpolymer (EPDM)/natural rubber (NR) blends. Dicumyl peroxide (DCP) was applied as a crosslinking agent. In terms of tensile properties, peroxide vulcanized blend shows higher tensile strength and tensile modulus (stress at 100% elongation, M₁₀₀) as compared with the unvulcanized blend. The elongation at break of the peroxide vulcanized blend is higher for the blend with NR rich content compared with the EPDM rich content. The improvements in chemical and oil resistance as well as gel content of peroxide vulcanized blends have also proved the formation of crosslinks in the rubber phase. Scanning electron microscopy (SEM) micrographs from the surface extraction of the blends support that the crosslinks have occurred during dynamic vulcanization. Dynamical vulcanization with DCP has decreased the percent crystallinity of blends that can be attributed to the formation of crosslinks in the rubber.     

Phase morphology and melt rheological behavior of uncrosslinked and dynamically crosslinked polyolefin blends: role of macromolecular structure

Thermoplastic vulcanizates (TPVs) based on polypropylene (PP) with ethylene–octene copolymer (EOC) and ethylene propylene diene rubber (EPDM) have been prepared by co-agent-assisted peroxide crosslinking system. The study was pursued to explore the influence of two dissimilar polyolefin polymers having different molecular architecture on the state and mode of dispersion of the blend components and their influence on melt rheological properties. The effects of dynamic crosslinking of the PP/EOC and PP/EPDM have been compared with special reference to the concentration of crosslinking agent and ratio of blend components. Morphological analyses show that, irrespective of blend ratio, dynamic vulcanization exhibits a dispersed phase morphology with crosslinked EOC or EPDM particles in the continuous PP matrix. It was found that viscosity ratio plays a crucial role in determining the state and mode of dispersion of blend components in the uncrosslinked system. The lower viscosity and torque values of uncrosslinked and dynamically crosslinked blends of PP/EOC in the melt state indicates that they exhibit better processing characteristics when compared to corresponding PP/EPDM blends.     

Study on morphology of ternary polymer blends. I. Effects of melt viscosity and interfacial interaction

The morphology of some ternary blends was investigated. In all of the blends polypropylene, as the major phase, was blended with two different minor phases, ethylene–propylene–diene terpolymer (EPDM) or ethylene–propylene–rubber (EPR) as the first minor phase and high‐density polyethylene (HDPE) or polystyrene (PS) as the second minor phase. All the blends were investigated in a constant composition of 70/15/15 wt %. Theoretical models predict that the dispersed phase of a multiphase polymer blend will either form an encapsulation‐type phase morphology or phases will remain separately dispersed, depending on which morphology has the lower free energy or positive spreading coefficient. Interfacial interaction between phases was found to play a significant role in determining the type of morphology of these blend systems. A core–shell‐type morphology for HDPE encapsulated by rubber was obtained for PP/rubber/PE ternary blends, whereas PP/rubber/PS blends showed a separately dispersed type of morphology. These results were found to be in good agreement with the theoretical predictions. Steady‐state torque for each component was used to study the effect of melt viscosity ratio on the morphology of the blends. It was found that the torque ratios affect only the size of the dispersed phases and have no appreciable influence on the type of morphology. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1129–1137, 2001     

Effect of E/P ratio and VA content on flow behavior of EPDM and EVA blends

The effect of E/P ratio of EPDM rubber and VA content of EVA copolymer on the flow behavior along with the extrudate morphology of EVA and EPDM blends have been studied as a function of shear rate and processing temperature. High E/P ratio EPDM rubber and low VA content EVA render high viscosities to the blend within the temperature range studied. The same trends hold true for extrudate swell. Stored elastic energy and relaxation time are higher for high E/P ratio EPDM and low VA content EVA. However, compositions with low E/P ratio EPDM exhibit higher shear modulus. At a particular blend composition these rheological parameters show a change in their pattern. Melt fracture occurs to a larger extent for the high E/P ratio EPDM in its blend with low VA content EVA. © 1994 John Wiley & Sons, Inc.     

Tensile properties and morphology of the dynamically cured EPDM and PP/HDPE ternary blends

The tensile properties and morphology of the polyolefin ternary blends of ethylenepropylene–diene terpolymer (EPDM), polypropylene and high density polyethylene were studied. Blends were prepared in a laboratory internal mixer where EPDM was cured in the presence of PP and HDPE under shear with dicumyl peroxide (DCP). For comparison, blends were also prepared from EPDM which was dynamically cured alone and blended with PP and HDPE later (cure–blend). The effect of DCP concentration, intensity of the shear mixing, and rubber/plastics composition was studied. The tensile strength and modulus increased with increasing DCP concentration in the blends of EPDM-rich compositions but decreased with increasing DCP concentration in blends of PP-rich compositions. In the morphological analysis by scanning electron microscopy (SEM), the small amount of EPDM acted as a compatibilizer to HDPE and PP. It was also revealed that the dynamic curing process could reduce the domain size of the crosslinked EPDM phase. When the EPDM forms the matrix, the phase separation effect becomes dominant between the EPDM matrix and PP or HDPE domain due to the crosslinking in the matrix.     

Dynamic mechanical properties and morphology of polypropylene block copolymers and polypropylene/elastomer blends

The relation between the dynamic mechanical properties and the morphology of polypropylene (PP) block copolymers and polypropylene/elastomer blends was studied by dynamic mechanical analysis (DMA), light- and electron microscopy. The latter techniques contributed to an improvement in assignments of relaxation transitions in the DMA spectra. It was established that PP block copolymers had multiphase structure since the ethylene/propylene rubber phase (EPR) formed in the copolymerization contained polyethylene (PE) domains. An identical morphology was found in the case of PP/polyolefin thermoplastic rubber (TPO) blends. Impact modification of PP by styrene/butadiene block copolymers led to a multiphase structure, too, due to the polystyrene (PS) domains aggregated in the soft rubbery polybutadiene phase. In the semicrystalline polyolefinic and in the amorphous styrene/butadienebased thermoplastic rubbers, PE crystallites and PS do mains acted as nodes of the physical network structure, respectively. PP/EPDM/TPO ternary blends developed for replacing high-density PE showed very high dispersion of the modifiers as compared to that of PP block copolymers. This fine dispersion of the impact modifier is a basic regulating factor of impact energy dissipation in the form of shear yielding and crazing.     

Optimization of accelerators on curing characteristics,tensile, and dynamic mechanical properties of (natural rubber)/(recycled ethylene‐propylene‐diene‐monomer) blends

The migration of sulfur from natural rubber (NR) compound to the ground waste ethylene‐propylene‐diene monomer (EPDM) rubber phase may have caused the cure incompatibility between these two rubbers. Optimization of accelerators had been adopted to overcome the cure incompatibility in NR/(R‐EPDM) blends as well as to get increased curative distribution. In this study, blends of NR and R‐EPDM were prepared. The effect of accelerator type on curing characteristics, tensile properties, and dynamic mechanical properties of 70/30/NR/(R‐EPDM) blend was investigated. Four types of commercial accelerators were selected [ie, N‐tert‐butyl‐2‐benzothiazyl‐sulphonamide , N‐cyclohexyl‐benzothiazyl‐sulfenamide (CBS), tetramethylthiuram disulfide, and 2‐mercaptobenzothiazol]. It was found that the tensile strength of the blends cured in the presence of CBS was relatively higher than the other three accelerators. Scanning electron micrographs of CBS‐cured NR/(R‐EPDM) blends exhibited more roughness and cracking path, indicating that higher energy was required toward the fractured surface. The high crosslinking density observed from the swelling method could be verified from the storage modulus (E′) and damping factor (tan δ) where (tetramethylthiuram disulfide)‐cured NR/(R‐EPDM) blends provided a predominant degree of crosslinking followed by N‐tert‐butyl‐2‐benzothiazyl‐sulphonamide , CBS, and 2‐mercaptobenzothiazol, respectively. J. VINYL ADDIT. TECHNOL., 21:79–88, 2015. © 2014 Society of Plastics Engineers     

Study on morphology of ternary polymer blends. II. Effect of composition

The composition effect on morphology of polypropylene/ethylene–propylene–diene terpolymer/polyethylene (PP/EPDM/PE) and polypropylene/ethylene–propylene–diene terpolymer/polystyrene (PP/EPDM/PS) ternary blends has been investigated. In all of the blends, polypropylene as the major phase was blended with two minor phases, that is, EPDM and PE or PS. From morphological studies using the SEM technique a core–shell morphology for PP/EPDM/PE and separated dispersed morphology for PP/EPDM/PS were observed. These results were found to be in agreement with the theoretical predictions. The composition of components affected only the size of dispersed phases and had no appreciable effect on the type of morphology. The size of each dispersed phase, whether it forms core or shell or disperses separately in matrix, can be related directly to its composition in the blend. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1138–1146, 2001