Silanized polymeric nanoparticles for DNA isolation

The aim of this study is to prepare silanized polymeric nanoparticles for DNA isolation. Polymeric p(HEMA)-IMEO-PBA nanoparticles around 85.7 nm diameter, was obtained by surfactant free emulsion polymerization for DNA isolation. Synthesized nanoparticles for characterization studies were realized scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and Zeta-size. Surface area, average particle size and size distribution were also performed. The surface area of synthesized silanized polymeric nanoparticles was 2460 m²/g. Synthesized polymeric nanoparticles were silanized with 3-(2-imidazoline-1-yl)propyl (triethoxysilane) (IMEO). After that, phenylboronic acid (PBA) which is DNA specific ligand were covalently binded to silanized polymeric nanoparticles. The amount of DNA adsorbed onto the p(HEMA)-IMEO-PBA nanoparticles first increased and then reached a saturation value at around 14.0 mg/mL of DNA concentration. The maximum adsorption was 672.41 mg/g silanized polymeric nanoparticles in the optimum adsorption medium. The maximum DNA adsorption was achieved at 4 °C. The overall recovery of DNA was calculated as 95%. In repetitive adsorption–desorption circles, it is observed not being important decrease in DNA adsorption capacities. The results were shown that silanized polymeric nanoparticles can be a good alternative for DNA isolation.     

Adsorption of collagen to indium oxide nanoparticles and infrared emissivity study thereon

Adsorption of collagen to indium oxide nanoparticles was carried out in water–acetone solution at volumetric ratio of 1:1 with pH value varying from 3.2 to 9.3. As indicated by TGA, maximum collagen adsorption to indium oxide nanoparticles occurred at pH of 3.2. It was proposed that noncovalent interactions such as hydrogen bonding, hydrophilic and electrostatic interactions made main contributions to collagen adsorption. The IR emissivity values (8–14 μm) of collagen-adsorbed indium oxide nanoparticles decreased significantly compared to either pure collagen or indium oxide nanoparticles possibly due to the interfacial interactions between collagen and indium oxide nanoparticles. And the lowest infrared emissivity value of 0.587 was obtained at collagen adsorption of 1.94 g/100 g In₂O₃. On the chance of improved compatibility with organic adhesives, the chemical activity of adsorbed collagen was further confirmed by grafting copolymerization with methyl methacrylate by formation of polymer shell outside, as evidenced by IR spectrum and transmission electron microscopy.     

Synthesis and characterization of amino acid containing Cu(II) chelated nanoparticles for lysozyme adsorption

Immobilized metal ion affinity chromatography (IMAC) is a useful method for adsorption of proteins that have an affinity for transition metal ions. In this study, poly(hydroxyethyl methacrylate-methacryloyl-l-tryptophan) (PHEMATrp) nanoparticles were prepared by surfactant free emulsion polymerization. Then, Cu(II) ions were chelated on the PHEMATrp nanoparticles to be used in lysozyme adsorption studies in batch system. The maximum lysozyme adsorption capacity of the PHEMATrp nanoparticles was found to be 326.9 mg/g polymer at pH 7.0. The nonspecific lysozyme adsorption onto the PHEMA nanoparticles was negligible. In terms of protein desorption, it was observed that adsorbed lysozyme was readily desorbed in medium containing 1.0 M NaCl. The results showed that the metal-chelated PHEMATrp nanoparticles can be considered as a good adsorbent for lysozyme purification.     

Adsorption of gum Arabic on bioceramic nanoparticles

Surface modification agents can be used to tailor the surface chemistry and biological activity of bioceramic nanoparticles in very intriguing ways. However, the specific modes of interactions between macromolecules and nanoparticles can be difficult to characterize. The aim of this study was to investigate the adsorption of gum Arabic on hydroxyapatite (HAp) and magnetic nanoparticles (MNP) using the bicinchoninic acid (BCA) test. Gum Arabic (GA) is a natural gum that has been widely used as an emulsifying agent and shows promise for dispersing nanoparticles in aqueous solutions. The adsorption of GA onto HAp nanoparticles followed a Langmuir isotherm with an adsorption plateau occurring at 0.2 g GA/g HAp. The adsorption of GA onto MNP attained a maximum value of 0.6 g GA/g MNP, after which it decreased to approximately 0.2 g GA/g MNP. The maximum adsorption density of GA on both MNP and HAp is equivalent when normalized to the specific surface area (4 × 10^− 3 g GA/m²). Adsorbed GA molecules were displaced from the surface of HAp and MNP in the presence of phosphate ions.     

Na0.5Li0.5CoO2 nanopowders: Facile synthesis,characterization and their application for the removal of methylene blue dye from aqueous solution

In this paper, delafossite-type Na_0.5Li_0.5CoO₂ nanoparticles (NPs) with an average particle size of 50 nm were successfully synthesized by sol–gel method. Prepared NPs were characterized by differential thermal analysis, powder X-ray diffraction, transmission electron microscopy, scanning electron microscopy, and scanning tunneling microscopy. The nanoparticles showed the excellent adsorption properties towards methylene blue dye (MBD) as a reactive dye. The kinetics of removal of MBD in aqueous solutions was studied in a series of experiments which were varied in the amount of NPs, contact time, pH, and temperature. The experimental data were fitted very well in the pseudo-second order kinetic model and the Freundlich adsorption isotherm model. 92% of dye was successfully removed in 10 min using 0.02 g Na_0.5Li_0.5CoO₂ NPs in a pH = 11. Thermodynamic study indicates that the adsorption of MBD is feasible, and spontaneous in nature.     

Polypyrrole–titanium(IV) doped iron(III) oxide nanocomposites: Synthesis,characterization with tunable electrical and electrochemical properties

Titanium(IV)-doped synthetic nanostructured iron(III) oxide (NITO) and polypyrrole (PPy) nanocomposites was fabricated by in situ polymerization using FeCl₃ as initiator. The polymer nanocomposites (PNCs) and pure NITO were characterized by X-ray diffraction, Föurier transform infrared spectroscopy, scanning electron microscopy, electron dispersive X-ray spectroscopy, transmission electron microscopy, etc. Thermo gravimetric and differential thermal analyses showed the enhancement of thermal stability of PNCs than the pure polymer. Electrical conductivity of the PNCs had increased significantly from 0.793 × 10^?2 S/cm to 0.450 S/cm with respect to the PPy, and that had been explained by 3-dimensional variable range hopping (VRH) conduction mechanisms. In addition, the specific capacitance of PNCs had increased from 147 F/g to 176 F/g with increasing NITO content than that of pure NITO (26 F/g), presumably due to the growing of mesoporous structure with increasing NITO content in PNCs which reduced the charge transfer resistance significantly.     

Microwave-assisted hydrothermal synthesis of zinc oxide particles starting from chloride precursor

Zinc oxide (ZnO) was synthesized using a microwave assisted hydrothermal (MAH) process based on chloride/urea/water solution and under 800 W irradiation for 5 min. In the bath, Zn²⁺ ions reacted with the complex carbonate and hydroxide ions to form zinc carbonate hydroxide hydrate (Zn₄CO₃(OH)₆·H₂O), and the conversion from Zn₄CO₃(OH)₆·H₂O to ZnO was synchronously achieved by a MAH process. The as-prepared ZnO has a sponge-like morphology. However, the initial sponge-like morphology of ZnO could change to a net-like structure after thermal treatment, and compact nano-scale ZnO particles were finally obtained when the period of thermal treatment increased to 30 min. Pure ZnO nanoparticles was obtained from calcination of loose sponge-like ZnO particles at 500 °C. The analysis of optical properties of these ZnO nanoparticles showed that the intensity of 393 nm emission increased with the calcination temperature because the defects were reduced and the crystallinity was improved.     

Effects of ZrO2 addition on phase stability and photocatalytic activity of ZrO2/TiO2 nanoparticles

ZrO₂/TiO₂ nanoparticles with various Zr/Ti ratios (0–0.9) were prepared by a polymer complex solution method (PCSM). The prepared samples were characterized using transmission electron microscopy (TEM), the Brunauer, Emmett & Teller (BET) method, X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FT-IR). The ZrO₂/TiO₂ photocatalyst showed a high specific area and small crystal size. The XRD pattern for the Zr/Ti = 0.1 sample indicated that the addition of ZrO₂ stabilized the anatase phase of TiO₂ up to 800 °C. The photocatalytic activity of Zr/Ti = 0.1 sample was higher than that of the TiO₂ sample and commercially available Degussa P25. The high photocatalytic activity can be attributed to stronger adsorption in the visible light region, higher specific area, smaller crystal size and increased surface OH groups.     

Synthesis and characterization of spherical polymer brushes

The synthesis of spherical polymer brushes consisting of a nano-SiO₂ core modified by γ-methacryloxypropyl trimethoxy-silane and a shell of linear polyacrylamide by grafting polymerization was described. The spherical polymer brushes were characterized by Transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR) and Thermo-gravimetric analysis (TGA). After cleavage of the ester group that connected the polymers to the surface, the molecular weight of the brushes was determined by Gel Permeation Chromatography (GPC). The results showed that the average diameter of spherical polymer brushes was ca. 140 nm while weight average molecular weight and surface grafting density were 1.407 × 10³ g/mol and 1.016 × 10^?4 mol/g respectively.     

Anti-amyloidogenic activity of glutathione-covered gold nanoparticles

This study is an investigation of the effect of biocompatible glutathione-covered gold nanoparticles (AuSG_7) with an average size of 3 nm on the amyloid fibrils of hen egg-white lysozyme. The anti-amyloid activity of AuSG_7 nanoparticles on this protein was monitored with thioflavin T assay, atomic force microscopy and transmission electron microscopy. The study found that AuSG_7 nanoparticles in vitro depolymerize the amyloid aggregates and inhibit lysozyme aggregate formation. The ability to inhibit amyloid formation and promote amyloid disassembly has concentration-dependent characteristics: the concentration of nanoparticles at which inhibition is half maximal (IC₅₀) was found to be 6.19 μg/mL, and the concentration at which depolymerization is half maximal (DC₅₀) was found to be 8.26 μg/mL.     

Preparation of surface modified zinc oxide nanoparticle with high capacity dye removal ability

In this paper, the surface modification of zinc oxide nanoparticle (ZON) by amine functionalization was studied to prepare high capacity adsorbent. Dye removal ability of amine-functionalized zinc oxide nanoparticle (AFZON) and zinc oxide nanoparticle (ZON) was also investigated. The physical characteristics of AFZON were studied using Fourier transform infrared (FTIR), scanning electron microscopy (SEM) and X-ray diffraction (XRD). Acid Blue 25 (AB25), Direct Red 23 (DR23) and Direct Red 31 (DR31) were used as model compounds. The effect of operational parameters such as dye concentration, adsorbent dosage, pH and salt on dye removal was evaluated. The isotherm and kinetic of dye adsorption were studied. The maximum dye adsorption capacity (Q₀) was 20 mg/g AB25, 12 mg/g DR23 and 15 mg/g DR31 for ZON and 1250 mg/g AB25, 1000 mg/g DR23 and 1429 mg/g DR31 for AFZON. It was found that dye adsorption followed Langmuir isotherm. Adsorption kinetic of dyes was found to conform to pseudo-second order kinetics. Dye desorption tests (adsorbent regeneration) showed that the maximum dye release of 90% AB25, 86% for DR23 and 90% for DR31 were achieved in aqueous solution at pH 12. Based on the data of the present investigation, it can be concluded that the AFZON being an adsorbent with high dye adsorption capacity might be a suitable alternative to remove dyes from colored aqueous solutions.     

Poly(hydroxyethyl methacrylate-co-methacryloylamidotryptophane) nanospheres and their utilization as affinity adsorbents for porcine pancreas lipase adsorption

Novel nanospheres with an average size of 350 nm utilizing N-methacryloyl-(l)-tryptophane methyl ester (MATrp) as a hydrophobic monomer were prepared by surfactant free emulsion polymerization of 2-hydroxyethyl methacrylate (HEMA), (MATrp) conducted in an aqueous dispersion medium. MATrp was synthesized using methacryloyl chloride and (l)-tryptophane methyl ester. Specific surface area of the non-porous nanospheres was found to be 1902.3 m²/g. poly(HEMA–MATrp) nanospheres were characterized by Fourier Transform Infrared Spectroscopy (FTIR) and scanning electron microscopy (SEM). Average particle size and size distribution measurements were also performed. Elemental analysis of MATrp for nitrogen was estimated at 1.36 mmol/g nanospheres. Then, poly(HEMA–MATrp) nanospheres were used in the adsorption of porcine pancreas lipase in a batch system. Using an optimized adsorption protocol, a very high loading of 558 mg enzyme/g nanospheres was obtained. The adsorption phenomena appeared to follow a typical Langmuir isotherm. The K_m value for immobilized lipase (16.26 mM) was higher than that of free enzyme (10.34 mM). It was observed that enzyme could be repeatedly adsorbed and desorbed without significant loss in adsorption amount or enzyme activity. These findings show considerable promise for this material as an adsorption matrix in industrial processes.     

Poly(hydroxyethyl methacrylate) nanobeads containing imidazole groups for removal of Cu(II) ions

Poly(hydroxyethyl methacrylate) (PHEMA) nanobeads with an average size of 300 nm in diameter and with a polydispersity index of 1.156 were produced by a surfactant free emulsion polymerization. Specific surface area of the PHEMA nanobeads was found to be 996 m²/g. Imidazole containing 3-(2-imidazoline-1-yl)propyl(triethoxysilane) (IMEO) was used as a metal-chelating ligand. IMEO was covalently attached to the nanobeads. PHEMA-IMEO nanobeads were used for the removal of copper(II) ions from aqueous solutions. To evaluate the degree of IMEO loading, the PHEMA nanobeads were subjected to Si analysis by using flame atomizer atomic absorption spectrometer and it was estimated as 973 µmol IMEO/g of polymer. The PHEMA nanobeads were characterized by transmission electron microscopy and fourier transform infrared spectroscopy. Adsorption equilibrium was achieved in about 8 min. The adsorption of Cu²⁺ ions onto the PHEMA nanobeads was negligible (0.2 mg/g). The IMEO attachment into the PHEMA nanobeads significantly increased the Cu²⁺ adsorption capacity (58 mg/g). Adsorption capacity of the PHEMA-IMEO nanobeads increased significantly with increasing concentration. The adsorption of Cu²⁺ ions increased with increasing pH and reached a plateau value at around pH 5.0. Competitive heavy metal adsorption from aqueous solutions containing Cu⁺, Cd²⁺, Pb²⁺ and Hg²⁺ was also investigated. The adsorption capacities are 61.4 mg/g (966.9 µmol/g) for Cu²⁺; 180.5 mg/g (899.8 µmol/g) for Hg²⁺; 34.9 mg/g (310.5 µmol/g) for Cd²⁺ and 14.3 mg/g (69 µmol/g) for Pb²⁺. The affinity order in molar basis is observed as Cu²⁺ > Hg²⁺ > Cd²⁺ > Pb²⁺. These results may be considered as an indication of higher specificity of the PHEMA-IMEO nanobeads for the Cu²⁺ comparing to other ions. Consecutive adsorption and elution operations showed the feasibility of repeated use for PHEMA-IMEO nanobeads.     

Hydrophobic microbeads as an alternative pseudo-affinity adsorbent for recombinant human interferon-α via hydrophobic interactions

Hydrophobic interaction chromatography (HIC) is increasingly used for protein purification, separation and other biochemical applications. The aim of this study was to prepare hydrophobic microbeads and to investigate their recombinant human interferon-α (rHuIFN-α) adsorption capability. For this purpose, we had synthesized functional monomer, N-methacryloyl-l-phenylalanine (MAPA), to provide a hydrophobic functionality to the adsorbent. The poly(2-hydroxyethyl methacrylate-N-methacryloyl-l-phenylalanine) [poly(HEMA–MAPA)] microbeads were prepared by suspension copolymerization. microbeads were characterized using FTIR, swelling behavior, and SEM micrographs. Equilibrium swelling ratio of poly(HEMA–MAPA) and poly(HEMA) microbeads were 53.3% and 69.3%, respectively. The specific surface area and average pore diameters determined by BET apparatus were 17.4 m²/g and 47.3 Å for poly(HEMA) microbeads and 18.7 m²/g and 49.8 Å for poly(HEMA–MAPA) microbeads. Adsorption experiments were performed under different conditions. Maximum rHuIFN-α adsorption capacity was found to be 137.6 ± 6.7 mg/g by using poly(HEMA–MAPA) microbeads with a size range of 150–250 μm and containing 327 μmol MAPA/g microbeads. Compared with poly(HEMA–MAPA) microbeads, nonspecific rHuIFN-α adsorption onto plain poly(HEMA) microbeads was very low, about 4.2 ± 2.3 mg/g. To determine the effects of adsorption conditions on possible conformational changes of rHuIFN-α structure, fluorescence spectrophotometry was employed. Repeated adsorption–elution processes showed that these microbeads are suitable for repeatable rHuIFN-α adsorption.     

Preparation of chitosan/magnetite composite beads and their application for removal of Pb(II) and Ni(II) from aqueous solution

A simple and effective process has been proposed to prepare chitosan/magnetite nanocomposite beads with saturation magnetization value as high as uncoated Fe₃O₄ nanoparticles (ca. 54 emu/g). The reason was that the coating chitosan layer was so thin that it did not affect magnetic properties of these composite beads. Especially, chitosan on the surface of the magnetic Fe₃O₄ nanoparticles is available for coordinating with heavy metal ions, making those ions removed with the assistance of external magnets. Maximum adsorption capacities for Pb(II) and Ni(II), occurred at pH 6 and under room temperature were as high as 63.33 and 52.55 mg/g respectively, according to Langmuir isotherm model. These results permitted to conclude that chitosan/magnetite nanocomposite beads could serve as a promising adsorbent not only for Pb(II) and Ni(II) (pH = 4–6) but also for other heavy metal ions in wastewater treatment technology.     

Equilibrium and kinetics of cadmium adsorption from aqueous solutions using untreated Pinus halepensis sawdust

Untreated Pinus halepensis sawdust has been investigated as an adsorbent for the removal of cadmium from aqueous solutions. Batch experiments were carried out to investigate the effect of pH, adsorbent dose, contact time, and metal concentration on sorption efficiency. The favorable pH for maximum cadmium adsorption was at 9.0. For the investigated cadmium concentrations (1–50 mg/L), maximum adsorption rates were achieved almost in the 10–20 min of contact. An adsorbent dose of 10 g/L was optimum for almost complete cadmium removal within 30 min from a 5 mg/L cadmium solution. For all contact times, an increase in cadmium concentration resulted in decrease in the percent cadmium removal (100–87%), and an increase in adsorption capacity (0.11–5.36 mg/g). The equilibrium adsorption data were best fitted with the Freundlich isotherm (R² = 0.960). The kinetics of cadmium adsorption was very well described by the pseudo-second-order kinetic model (R² > 0.999).     

Magnetic chitosan nanoparticles for removal of Cr(VI) from aqueous solution

A simple method was introduced to prepare magnetic chitosan nanoparticles by co-precipitation via epichlorohydrin cross-linking reaction. The average size of magnetic chitosan nanoparticles is estimated at ca. 30 nm. It was found that the adsorption of Cr(VI) was highly pH-dependent and its kinetics follows the pseudo-second-order model. Maximum adsorption capacity (at pH 3, room temperature) was calculated as 55.80 mg·g^? 1, according to Langmuir isotherm model. The nanoparticles were thoroughly characterized before and after Cr(VI) adsorption. From this result, it can be suggested that magnetic chitosan nanoparticles could serve as a promising adsorbent for Cr(VI) in wastewater treatment technology.     

Synthesis,characterization and magnetic performance of Co-incorporated ordered mesoporous carbons

Co-incorporated ordered mesoporous carbon (Co-OMC) with magnetic frameworks has been synthesized via a one-pot self-assembly strategy. The effects of cobalt loading on carbon matrix, adsorption properties and magnetic properties of the resultant mesostructured cobalt/carbon composites were investigated by nitrogen sorption, X-ray diffraction (XRD), transmission electron microscopy (TEM), thermogravimetric analysis (TG) and magnetometer measurements. The results show that the mesoporous composites with a high cobalt content (such as 18.0 wt%) possess an ordered and uniform mesoporous structure (5.3 nm), high surface areas (up to 687 m²/g) and high pore volumes (up to 0.54 cm³/g). Cobalt nanoparticles of size 4–9 nm are confined inside the mesopores or walls of the mesoporous carbon. These materials exhibit typical ferromagnetic characteristics. The saturation magnetization strength can be easily adjusted by changing the content of cobalt. The carbonization temperatures have significant effects on the structure and magnetic properties of Co-OMC also.     

Superparamagnetic maghemite/polyrhodanine core/shell nanoparticles: Synthesis and characterization

Maghemite nanoparticles (MNPs) with a thin layer of polyrhodanine (PRd) at the surface were synthesized via chemical oxidative polymerization of rhodanine monomer at the MNPs surface in the presence of ferric chloride as oxidant. X-ray diffraction (XRD) pattern gave direct evidence that the synthesized nanoparticles are crystalline maghemite of about 8 nm in size. Magnetization of the particles versus an applied magnetic field exhibited no hysteresis loop, indicated superparamagnetic behavior in the particles. Transmission electron microscopy (TEM) together with Fourier-transform infrared (FT-IR) spectroscopy were used to determine the morphology and the chemical structure of the magnetic core and the polymeric shell. Through the microscopy analysis the shell thickness was estimated to be about 1.5 nm, whereas through thermogravimetric analysis (TGA) it was estimated to be about 0.6 nm. Moreover inductively coupled plasma optical emission spectroscopy (ICP-OES) measurements revealed that the oxidant residue in the polymer backbone is ca. 4 wt.%.     

Preparation of nanostructured nickel aluminate spinel powder from spent NiO/Al2O3 catalyst by mechano-chemical synthesis

In this paper, the possibility of mechano-chemical synthesis, as a single step process for preparation of nanostructured nickel aluminate spinel powder from NiO/Al₂O₃ spent catalyst was investigated. Powder samples were characterized in terms of composition, morphology, structure, particle size and surface area using complementary techniques such as X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), differential thermal analysis (DTA) and volumetric adsorption of nitrogen. It was found that formation of spinel was possible after 60 h of milling with no heat treatment. Additionally, influence of mechanical activation on the heat treatment temperature was discussed. It was observed that heat treatment of 15 h milled sample at 1100 °C is enough to produce nickel aluminate spinel. A product of direct mechanical milling showed higher value of surface area (42.3 m²/g) and smaller crystallite size (12 nm) as compared to the heat treated product.