A polarization independent GaAs-AlGaAs electrooptic modulator

Two designs for polarization independent GaAs-AlGaAs interferometric electrooptic modulators are described. One design uses the linear electrooptic effect to couple degenerate TE/TM eigenmodes of a single-mode waveguide. In the other design the eigenmodes need only be near degenerate. The design using the coupling between near degenerate TE/TM modes utilizes a novel biasing scheme. A novel polarization independent GaAs-AlGaAs interferometric optical modulator based on this design has been fabricated and characterized at 1.3 μm. This modulator is fabricated as a traveling wave modulator incorporating 50 Ω, phase velocity matched, low microwave loss electrodes for maximum electrical bandwidth     

Polarization-independent waveguide modulators using 1.57-μmδ-strained InGaAs-InGaAsP quantum wells

We fabricated a multiple-quantum-well waveguide modulator incorporating two tensile S-strained layers, within a nominally lattice matched well, that act to provide bias-independent Stark shift for both the light and heavy holes. We report results for two waveguide geometries. One is a 2.3-μm-wide ridge single-mode waveguide that was deep-etched 0.7 μm below the active region to ensure that the confinement factor for both the TE and TM modes are nearly equal. The other was a broad-area (slab) multimode waveguide. For both geometries, transmission measurements indicate polarization insensitivity within 3 dB for 2.5 V of reverse bias over the 1.600-1.630-μm wavelength range     

基于复合光波导偏振干涉技术的高灵敏度生化检测仪

利用射频溅射技术在一个单模玻璃光波导的局部表面淀积一层两端呈梯度的高折射率透明氧化物薄膜,形成低损失、高灵敏度平面复合光波导芯片。这种结构能够使得玻璃光波导内沿同一路径传播的横电基模(TE0)与横磁基模(TM0)在梯度薄膜区间产生纵向空间分离,导致TE0模的消逝场相比TM0模显著增强。利用复合光波导芯片,结合棱镜-样品池组合体和集成式选偏光探测器研制出基于偏振干涉测量的OWG-01型生化检测仪。对液体折射率响应的测试结果表明复合光波导芯片的热光效应非常小,而仪器的测量误差主要来自待测液体自身的折射率随温度的变化。     

Analysis of TE and TM modes in DFB lasers by two-dimensional theory

The two-dimensional theory of a distributed feedback (DFB) laser (which was previously presented and applied to the analysis of the laser threshold conditions for the transverse-electric (TE) mode in a simple three-layer waveguide structure) is developed to treat both TE and transverse-magnetic (TM) modes in a four-layer waveguide structure with a thin grating layer, which more closely reflects actual DFB laser structure. The differences between TE and TM modes for the dispersion relations and the laser threshold conditions are clarified. The effects of the waveguide structure (including grating layer thickness, refractive indexes of layers, coupling constant, and corrugation period) on the threshold gains and the gain differences between the two longitudinal modes on both sides of the Bragg frequencies are studied in detail for both TE and TM modes     

Laser-trimming adjustment of waveguide birefringence in optical FDMcomponents

Laser trimming of amorphous-silicon stress-applying films deposited on silica-based single-mode waveguides is demonstrated for controlling waveguide birefringence. Successful applications to polarization-insensitive operation of an optical ring resonator and a Mach-Zehnder interferometer are presented. A phase difference of less than π/100 between TE and TM modes has been attained. It is noted that this laser trimming method can also be applicable to other material devices such as LiNbO₃ and yttrium-aluminum-garnet (YAG), where waveguide birefringence control is a crucial factor in achieving the practical performance of the device     

Integrated optical waveguide polarizer based on photobleaching-induced birefringence in an electrooptic polymer

A TE-pass waveguide polarizer is fabricated by utilizing the photobleaching-induced birefringence at room temperature in an electrooptic polymer. The polarizer consists of the photobleached waveguide supporting only TE mode, which is integrated in the middle of the etched rib waveguide supporting both TE and TM modes. It has a simple structure and requires no high temperature process like poling. The measured polarization extinction ratio is about 21 dB at the wavelengths of 1.3 and 1.55 /spl mu/m, and the estimated excess loss is about 0.4 dB.     

Incoupling waveguide hologram with reduced polarization sensitivity

An incoupling waveguide hologram (IWGH) with significantly reduced polarization sensitivity was designed and fabricated in InP for 1550 nm wavelength. The IWGH couples the light from an optical fiber, irrespectively of the state of polarization, into the InP waveguide and simultaneously focuses it to a desired position in the waveguide. Conventional IWGHs are strongly polarization sensitive with a measured 19 dB difference in the incoupling efficiency between the TE and TM mode. In contrast, although some design parameters turned out to be slightly in error, the fabricated IWGHs designed for reduced polarization sensitivity exhibited a 3.1 dB difference in the incoupling efficiency between the TE and TM modes     

Crosstalk characteristics of Ti-LiNbO3intersecting waveguides and their application as TE/TM mode splitters

Crosstalk characteristics of an intersecting waveguide are presented. Two straight channel waveguides which intersect at an angle of a few degrees ony-cut LiNbO3were fabricated by in-diffusion of Ti. Experimental results show that the crosstalk characteristics are determined by the refractive index change profile and the geometry of intersection associated with guided wave modes. In a special case, a TE/TM mode splitter was obtained by using the intersecting waveguide which provides adequate anisotropy by the change in refractive indices. Splitting ratio was 17 and 14 dB for the TE and TM modes, respectively.     

Embedded channel polyimide waveguide fabrication by direct electronbeam writing method

A new embedded channel polyimide waveguide fabrication process by a direct electron beam writing method (DEBWM) is described. The new technique uses an electron-beam induced effect to directly alter the refractive indices of the two-layer polyimide. Both the core and the lower cladding have been fabricated at the same time in two-layer polyimides using electron beam with 25 keV energy. The obtained embedded channel waveguide was made of two kinds of polyimides, one for lower cladding and one for core and other claddings. Guide losses are 0.3 dB/cm for both TE and TM polarized incident lights and guiding mode is single-mode for TE. The optical properties of the waveguide and a relationship between the doses of electron beam and optical losses or loss dependence on wavelength are also mentioned     

Scattering at Circular-to-Rectangular Waveguide Junctions

A formally exact solution is given for the problem of scattering at a circular-to-rectangular waveguide junction and at a thick diaphragm, with a centered circular aperture, in a rectangular waveguide. The method uses normal TE and TM mode expansions of the waveguide fields and traditional mode matching of the transverse electric and magnetic fields at the junction boundary. Exact closed-form expressions are obtained for the electric field mode-matching coefficients which couple the TE(TM) modes in the rectangular guide to the TE(TM) and TM(TE) modes in the circular guide. Numerical results are presented for the case of TE/sub 10/ mode propagation in the larger rectangular guide with all other modes cutoff. Convergent numerical results for the equivalent shunt susceptances of such junctions are obtained when about 12 modes (eight TE and four TM) are retained in the circular waveguide or in the circular aperture of the diaphragm. The results are graphically compared with formulas and curves due to the quasi-static theory of Bethe and the variational theory given in the Waveguide Handbook [2].     

Measurement of depolarization ratio and ultimate limit ofpolarization crosstalk in silica-based waveguides by using a POLCR

A polarization optical low coherence reflectometer (POLCR) is described that enables us to excite only the transverse electric (TE) mode of a test waveguide and to measure its Rayleigh backscatter signal distributions in the TE and transverse magnetic (TM) modes at a spatial resolution of 0.3 mm. The depolarization ratios of silica-based waveguides with relative refractive index differences of Δ=0.45 and 0.75% are obtained as 0.14 and 0.10, respectively, by measuring the bias in the ratio between the distributions in the TM and TE modes of each waveguide. By using the depolarization ratios and the Rayleigh backscatter signal levels, we calculate the ultimate polarization crosstalks to be -53 and -51 dB over 1 km, respectively. The actual polarization crosstalks of previously fabricated waveguides are about 50 dB higher than their ultimate limits for the same length of fiber     

Refractive-index profiling of graded-index planar waveguides fromeffective indexes measured for both mode types and at differentwavelengths

It is well known that, under the WKB approximation, the refractive-index profile of a graded-index planar waveguide can be calculated from the corresponding effective-index function, which can be found approximately by least-squares fitting of a set of measured effective indexes. In the previous work, effective indexes measured for a particular type of modes (the TE or TM modes) at a single wavelength are used. This requires that the waveguide supports at least three modes of the same type. In this paper, techniques of combining the effective indexes measured for both mode types and at different wavelengths are proposed and demonstrated with examples. With these techniques, single-mode and two-mode waveguides can be profiled     

Collinear interaction of light with space-charge waves in a semiconductor waveguide

The dispersion equation for space-charge waves (SCWs) that couples the wave vector of a traveling wave with frequency and the parameters of a semiconductor waveguide layer is obtained. Numerical analysis of the co-and contradirectional SCW-optical interaction for guided TE and TM modes in a waveguide structure based on n-GaAs is performed. It is demonstrated that the power exchange between the TE modes is more effective than the power exchange between the TM modes. The intervals of the waveguide layer thickness with a relatively high efficiency of the mode transformation are determined.     

Polarization properties of a fiber-to-asymmetric planar waveguidecoupler

A coupled mode model describing the light transfer between a single-mode fiber and a planar asymmetric waveguide, which takes into account the two dimensions of the waveguide cross sections, as well as the TE or TM polarization of the planar waveguide modes, is presented. This model is applied to the practical case of a distributed (curved fiber) coupler, and the possibility of light modulation by changing the refractive index: of the cover medium is pointed out. The action of such a coupler as a polarizer, which could be externally driven, is also considered     

对称单负材料平面波导的波导模

基于经典电磁理论建立了芯层为单负材料的对称三层平板波导的导波方程,采用图解法研究了该波导中的TE和TM波导模,分析了TE波导模和TM波导模会受波导参数μ1/μ2和R的影响,给出TE模和TM模解的横向场分布图.结果显示,在单负材料的对称三层平板波导中只存在慢波导模,TE慢波模只能在磁负材料中传播,TM慢波模只能在电负材料...     

Polarization sensitivity of a silica waveguide thermooptic phaseshifter for planar lightwave circuits

A thermooptic (TO) phase shifter, which consists of a thin-film heater loaded on a silica-based single-mode waveguide on a Si substrate, was found to exhibit a sli1h,t polarization dependence of about 3.1% between the TE and TM modes. This dependence, which is caused by anisotropic stress concentration due to local heating, was successfully reduced by forming stress-releasing grooves on either side of the heater     

An Efficient and Simple Analytical Model for Analysis of Propagation Properties in Impedance Waveguides

In this paper, propagation properties of a parallel-plate waveguide with tunable artificial impedance surfaces as sidewalls are studied both analytically and numerically. The impedance surfaces comprise an array of patches over a dielectric slab with embedded metallic vias. The tunability of surfaces is achieved with varactors. Simple design equations for tunable artificial impedance surfaces, as well as dispersion equations for the TE and TM modes are presented. The propagation properties are studied in three different regimes: multimode waveguide, single-mode waveguide, and below-cutoff waveguide. The analytical results are verified with numerical simulations.      

Design of three-dimensional silica on a silicon single-mode single-polarization waveguide

We present a design of three-dimensional(3D) silica on a silicon single-mode single-polarization waveguide (SMSPW) by taking into consideration the induced birefringence effect of the silica.This can cut off the TM mode and transmit the TE mode.The characteristics of the light propagating across the polarization maintaining waveguide were simulated by 3D beam propagation methods(3D-BPM).The result showed that the SMSPW has a high extinction ratio over 50 dB for the TM mode.Without increasing the complexi...     

Analysis of TE/TM mode selectivity in DFB lasers with a phase-shift region

In phase-shift distributed feedback (DFB) lasers, there is limited suppression of the TM mode despite extremely large submode suppressibility. The TE/TM mode selectivity of a DFB laser structure with a nonuniform waveguide region as the phase shifter is analyzed. Calculations of the threshold gain difference between the TE and TM modes are performed using the effective index method and the coupled-wave theory. It is found that the TM mode suppressibility can be doubled by optimizing the dimensions of the phase-shift region. This structure overcomes the TM mode problem.<>     

硅基二氧化硅单模单偏振光波导的设计

在不增加工艺难度的前提下,利用硅基二氧化硅光波导的双折射效应并结合有效折射率方法, 设计了一种新型单模单偏振波导, 使得两个正交偏振模式中的TM 模式被截止, TE 模式可以通过. 利用三维有限差分光束传输法(3D -BPM ) 进行数值模拟,结果显示,对于TM 模式消光比可高达到50dB 以上.此种结构的光波导可以直接制作偏振器, 同时还易与其他波导器件集成.