自燃/球磨法制备NiZn系铁氧体

以金属硝酸盐和柠檬酸为原料,用溶胶凝胶自燃烧法制备NiZn系铁氧体前驱体粉末(Ni0.4Zn0.6Fe2O4,Ni0.2Zn0.6Cu0.2Fe2O4,Ni0.33Zn0.59Cu0.11Fe1.97O4(Bi2O3)0.002和Ni0.33Zn0.59Cu0.11 Fe1.97O4(Bi2O3)0.002(MnO2)0.02),然后经30小时高能球磨,从X-ray衍射谱中发现前驱体粉末虽然基本上是尖晶石结构,但是还有一些杂相,经过球磨,杂相明显减少,结构更加完整,颗粒减小.前驱体粉末Ni0.33Zn0.59Cu0.11Fe1.97O4(Bi2O3)0.002经30小时球磨后,在空气中退火,退火温度分别为400℃,600℃,800℃,900℃,1000℃.用X-ray衍射谱分析其物相,发现在800℃退火得到单相的尖晶石结构,无杂相.该样品的最佳退火温度低于1000℃.用振动样品磁强计分别测量制备态和退火态样品粉末的磁性,可以看出,随退火温度的升高,比饱和磁化强度σs逐渐增大,矫顽力Hc逐渐减小,当900℃退火后,比饱和磁化强度已接近块状NiZn系铁氧体.1000℃退火后,上述四种样品中Ni0.4Zn0.6Fe2O4具有最高的比饱和磁化强度σs=65.09emu/g.本文为NiZn铁氧体的低温烧结提供了有用的实验数据.     

非晶金刚石薄膜对温度的敏感性研究

采用过滤阴极真空电弧技术制备非晶金刚石薄膜, 在-190～600℃范围研究非晶金刚石薄膜的温度敏感性. 利用液氮泵在Linkam试验台上冷却样品并实时采样, 通过炉中退火实现样品加热. 分别测试可见光拉曼光谱和纳米压痕, 研究薄膜的微结构和机械性能的变化. 实验表明: 过滤阴极真空电弧制备的非晶金刚石薄膜具有较好的热稳定性. 在空气中退火到400℃, 其硬度和弹性模量基本保持不变, 其结构可以一直稳定到500℃, 但是到600℃, 薄膜因为氧化作用而快速消耗. 非晶金刚石薄膜的可见光拉曼光谱显示随着温度的升高, 谱峰峰位向高频偏移. 在低温冷却过程中, 薄膜对温度变化不敏感, 其结构保持不变.     

Cr~（3＋）离子掺杂对Al_2O_3粉末结构及发光性能影响

采用球磨法制备了不同浓度Cr_2O_3掺杂的Al_2O_3粉体,并在700℃、1200℃空气中退火2 h。1200℃退火后样品,除掺杂浓度为1.6%的样品中出现少量γ-Al_2O_3相外,其余样品相均为纯α-Al_2O_3。样品晶格常数随着Cr~（3＋）离子浓度的增加而增加。采用波长为579 nm的激发光源对佯品进行荧...     

磁控溅射制备SiC薄膜的高温热稳定性

采用磁控溅射方法在Si基底上制备SiC薄膜,研究了SiC薄膜经不同温度和气氛条件高温退火前后结构、成份的变化.结果表明,薄膜主要以非晶为主,由Si-C键,C-C键和少量Si的氧化物杂质组成;在真空条件下经高温退火后,薄膜C-C键的含量减少,而Si-C键的含量增加,真空退火有利于SiC的形成;在800℃空气中退火后,薄膜表面生成一层致密的SiO2薄层,阻止了氧气与薄膜内部深层的接触,有效保护了内部的SiC.在空气条件下,SiC薄膜在800℃具有较好的热稳定性.     

退火对Al/CdZnTe肖特基接触特性的影响

在CdZnTe表面采用真空蒸镀制备了Au和Al电极,研究了在N_2氛围退火对Al/CdZnTe接触特性的影响。退火温度在100℃到300℃之间变化,退火时间为5 min。采用Agilent4155c半导体测试仪测试了样品在不同温度退火后的I-V特性。采用Agilent 4294A高精度阻抗分析仪测试了样品在不同温度退火后的C-V特性。I-V和C-V曲线表明,低温退火会使接触势垒高度增加,理想因子趋近于1,电容值下降为退火前的一半左右。当退火温度高于250℃时,接触势垒高度下降,理想因子偏离1,电容值下降近一个数量级。     

高能球磨时间和退火温度对制备TiNi合金粉的影响

为获得高能球磨时间和退火温度对TiNi机械合金粉特性的影响机制,采用X射线衍射(XRD)、扫描电子显微镜(SEM)、X射线能谱仪(EDS)、差示扫描量热法(DSC)等分析方法对TiNi合金粉进行了研究。结果表明,机械合金的相成分随着在氩气保护气氛中的球磨时间和退火温度的不同而发生变化。球磨22h的产物是非晶态TiNi合金、Ti的固溶体、Ni的固溶体,球磨27h的产物是非晶态TiNi合金粉和Ni固溶体相,球磨30h发生了明显的固相反应,生成了TiNi、Ni3Ti、Ti3Ni4等物相;在650℃/5h和1000℃/5h下的退火产物都是Ni3Ti、Ti2Ni、TiNi2、TiNi和TiC,但在上述2个退火温度下TiNi并不是主要物相,其中在650℃退火时TiNi的含量明显更低。     

Fe掺杂量和退火氛围对TiO2薄膜晶体结构和磁性能的影响

采用直流磁控溅射方法在玻璃基片上制备了不同Fe掺杂量的TiO2薄膜,并对薄膜分别在空气和真空氛围下500℃进行30min退火处理。研究了Fe掺杂量和退火氛围对TiO2薄膜的结晶状态、表面形貌和磁性能的影响。结果表明,真空中500℃下退火的Fe掺杂的TiO2薄膜表现为非晶态结构,没有观察到室温铁磁性能的出现,而空气中500℃退火的样品显示出良好的结晶状态,且所有掺杂的样品均显示出室温铁磁性,并且随着Fe掺杂量的增加,TiO2薄膜的晶体结构逐渐由锐钛矿相向金红石相转变。     

分散的Sm-Co永磁纳米颗粒的机械化学合成及磁性能

通过机械化学合成方法制备了矫顽力分别为2.95×106、2.83×106和8.60×105 A/m的分散的单晶纳米Sm2Co7、SmCo5和Sm2Co17硬磁颗粒。研究了球磨时间、原料配比和退火工艺等对所制备的纳米永磁颗粒的微观组织、结构和磁性能的影响。结果表明,机械化学球磨时间至少是4h或更长时间才能获得Sm-Co硬磁合金粉末。原料经过高能球磨后、未退火时,由于大部分颗粒为非晶结构,矫顽力较低,随着退火温度的上升,矫顽力增大,当退火温度为600℃时,达到最大值为2.83×106 A/m,然后,随着退火温度的进一步升高,矫顽力减小。Sm-Co纳米颗粒的粒径随着退火温度的降低而明显减小。     

分散的Sm-Co永磁纳米颗粒的机械化学合成及磁性能

通过机械化学合成方法制备了矫顽力分别为2.95×106、2.83×106和8.60×105A/m的分散的单晶纳米Sm2Co7、SmCo5和Sm2Co17硬磁颗粒。研究了球磨时间、原料配比和退火工艺等对所制备的纳米永磁颗粒的微观组织、结构和磁性能的影响。结果表明,机械化学球磨时间至少是4h或更长时才能获得Sm-Co硬磁合金粉末。原料经过高能球磨后、未退火时,由于大部分颗粒为非晶结构,矫顽力较低,随着退火温度的上升,矫顽力增大,当退火温度为600℃时,达到最大值为2.83×106A/m,然后,随着退火温度的进一步升高,矫顽力减小。Sm-Co纳米颗粒的粒径随着退火温度的降低而明显减小。     

NiCo2O4/Co3O4纳米材料的球磨法制备及电化学性能

通过高能球磨碳酸镍、碱式碳酸钴的方法制备了NiCo2O4/Co3O4复合材料.系统研究了原料质量比、球磨参数以及退火温度等对材料的微观形貌、结构、组份以及反应活化能和电化学性能的影响.结果表明,在碳酸镍和碱式碳酸钴质量比为2:8,球磨时间为48 h,退火温度为300℃条件下制得复合材料在电位范围0～0.45 V,电流密...     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Synthesis of Alumina-Zirconia Nanocomposites by Solgel Process

Al₂O₃-ZrO₂ nanocomposites were developed starting with the solgel process. Composite alumina-zirconia nanopowders were synthesized from metallorganic precursors (Aluminium secondary butoxide and zirconium Iso propoxide) using the solgel process. The parameters affecting the synthesis—solvent, concentration of precursor, R/H ratio (i.e., dilution of water in solvent)—were varied as also the temperature and pH. BET and TEM were used to measure nanosize. Diffuse reflectance spectroscopy and also qualitative optical absorption led to identical particle size estimate. The variation of process parameters was used to study the effect and interdependence of process parameters. Artificial Neural Networks was used to rigorously analyze the process. Although this led to confirmation of interdependence of parameters, the presence of a single overwhelming solvent variable was also established. Then the optimal process was used to synthesize more nanopowder. To produce bulk nanocomposite the nanopowders were sintered by varying the temperature and time period. The sintered lithoids were probed with a vickers hardness tester to measure elastic modulus, hardness, and fracture toughness. The results showed high elastic modulus, modest hardness, and very high fracture toughness.     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.