共查询到20条相似文献,搜索用时 46 毫秒
1.
一种混合驱动柔索并联仿生眼的轨迹规划 总被引:1,自引:0,他引:1
在与眼球运动相关的解剖学和运动学的基础上,设计了一种符合Listing定理的基于混合驱动柔索并联机构的3自由度机器人仿生眼.通过矢量封闭方法建立了逆运动学模型,求解出柔索并联机器人的雅可比矩阵和结构矩阵.利用达朗贝尔定理建立柔索并联机器人的力矩平衡方程组,采用广义逆矩阵的相关理论,以柔索张力矢量的2范数最小为目标进行张力优化.用蒙特卡洛方法计算出仿生眼球可达工作空间.最后,在Simulink环境下进行仿真,规划运动轨迹并得到柔索并联机器人运动特性的仿真结果,证明了本文设计的机构符合Listing定理.结果表明:基于混合驱动柔索并联机构的机器人仿生眼结构合理,数学模型正确. 相似文献
2.
3.
4.
5.
针对偏瘫患者外骨骼康复机器人降低外骨骼质量的要求,设计了一种辅助下肢外骨骼机器人,采用柔索驱动的膝关节,具有结构简单,质量轻的特点。同时利用ADAMS建立了外骨骼关节柔索驱动的动力学模型,绳索模块建立了柔索驱动模型,通过Ariel生物运动分析软件,采集髋、膝、踝关节运动数据,运用Spline函数进行了仿真分析。经过仿真分析柔索驱动在上台阶运动过程中的不同拉簧预紧力和拉簧刚度下传动特性和驱动力矩,为进一步研究设计下肢外骨骼提供依据。 相似文献
6.
阐述了一种线驱动与常规串联驱动相结合的混合设计方法.这种设计方法融合了线驱动并联机构和模块化串联机构的优点,而且混合驱动机器人的工作空间大于完全线驱动机器人的工作空间.文章首先介绍了混合驱动机器人的机构设计,也就是机器人的肩关节采用模块化串联结构,而肘、腕关节采用线驱动结构.然后利用几何分析的方法来解机器人前向运动学问题.在分析驱动线长与关节角之间变换关系的基础上,分别利用速度法和关节角增量法来计算机器人逆向运动学解.最后,使用VC++实现混合驱动机器人对直线运动轨迹进行跟踪的仿真,从而证明了文章所描述的设计方法的正确性. 相似文献
7.
冗余驱动仿下颌运动机器人工作空间分析及试验验证 总被引:1,自引:0,他引:1
根据人类下颌系统冗余驱动的生理特性,即下颌受颞下颌关节约束且受多于本身自由度数目的下颌肌肉驱动的特点,介绍了一种采用点接触高副模拟人体颞下颌关节的6PUS-2HKP(higher kinematic pair)冗余驱动并联机构来完成下颌运动,该机构可应用于牙科义齿性能测试.首先,建立机器人的坐标系,针对机构存在点接触高副的特点,分析和推导了冗余并联机构的独立位置参数和运动学方程.然后,采用下颌运动轨迹描记仪对实验对象下颌切点边缘性运动进行了采集.通过分析各驱动机构及点接触高副的运动范围,采用数值分析的方法获得了机器人的工作空间.最后,采用实验的方法,测量了仿下颌运动机器人做最大运动时下颌切点的运动轨迹.通过对比实验对象切点边缘性运动和工作空间仿真结果可知,该仿下颌运动机器人能够满足人类下颌运动空间要求. 相似文献
8.
本文提出了一种带有约束机构的并联柔索驱动转台,介绍该转台的机构构型,设计了一种利用模糊逻辑进行在线参数自适应的Fuzzy-PID控制器。该控制器能够对PID的参数进行在线自动调整,仿真结果表明,采用参数自适应模糊PID控制器后,控制系统的响应速度加快,超调量减小,过渡过程时间大大缩短,振荡次数少,具有较强的鲁棒性和良好的稳定性。 相似文献
9.
本文提出了一种带有约束机构的并联柔索驱动转台,介绍该转台的机构构型,设计了一种利用模糊逻辑进行在线参数自适应的Fuzzy-PID控制器.该控制器能够对PID的参数进行在线自动调整,仿真结果表明,采用参数自适应模糊PID控制器后,控制系统的响应速度加快,超调量减小,过渡过程时间大大缩短,振荡次数少,具有较强的鲁棒性和良好的稳定性. 相似文献
10.
11.
S. Shaw 《Journal of Computer Assisted Learning》1993,9(2):93-99
Abstract This paper describes an approach to the design of interactive multimedia materials being developed in a European Community project. The developmental process is seen as a dialogue between technologists and teachers. This dialogue is often problematic because of the differences in training, experience and culture between them. Conditions needed for fruitful dialogue are described and the generic model for learning design used in the project is explained. 相似文献
12.
European Community policy and the market 总被引:1,自引:0,他引:1
C. Lloyd 《Journal of Computer Assisted Learning》1993,9(2):86-91
Abstract This paper starts with some reflections on the policy considerations and priorities which are shaping European Commission (EC) research programmes. Then it attempts to position the current projects which seek to capitalise on information and communications technologies for learning in relation to these priorities and the apparent realities of the marketplace. It concludes that while there are grounds to be optimistic about the contribution EC programmes can make to the efficiency and standard of education and training, they are still too technology driven. 相似文献
13.
融合集成方法已经广泛应用在模式识别领域,然而一些基分类器实时性能稳定性较差,导致多分类器融合性能差,针对上述问题本文提出了一种新的基于多分类器的子融合集成分类器系统。该方法考虑在度量层融合层次之上通过对各类基多分类器进行动态选择,票数最多的类别作为融合系统中对特征向量识别的类别,构成一种新的自适应子融合集成分类器方法。实验表明,该方法比传统的分类器以及分类融合方法识别准确率明显更高,具有更好的鲁棒性。 相似文献
14.
Wayne O’Brien Author Vitae 《Journal of Systems and Software》2008,81(11):1997-2013
Development of software intensive systems (systems) in practice involves a series of self-contained phases for the lifecycle of a system. Semantic and temporal gaps, which occur among phases and among developer disciplines within and across phases, hinder the ongoing development of a system because of the interdependencies among phases and among disciplines. Such gaps are magnified among systems that are developed at different times by different development teams, which may limit reuse of artifacts of systems development and interoperability among the systems. This article discusses such gaps and a systems development process for avoiding them. 相似文献
15.
16.
This paper presents control charts models and the necessary simulation software for the location of economic values of the control parameters. The simulation program is written in FORTRAN, requires only 10K of main storage, and can run on most mini and micro computers. Two models are presented - one describes the process when it is operating at full capacity and the other when the process is operating under capacity. The models allow the product quality to deteriorate to a further level before an existing out-of-control state is detected, and they can also be used in situations where no prior knowledge exists of the out-of-control causes and the resulting proportion defectives. 相似文献
17.
潘丽 《自动化与仪器仪表》2014,(7):80-82
自然界的绝大部分信号都是以模拟的形式存在,因此模拟信号的采集转换存储在数字时代十分关键。文章讨论了在雷达信号处理领域基于AD9626的AD采集存储卡的设计原理、硬件结构和程序设计与芯片配置等问题,为今后相关领域的研究提供了可参考的方案。 相似文献
18.
Going through a few examples of robot artists who are recognized worldwide, we try to analyze the deepest meaning of what
is called “robot art” and the related art field definition. We also try to highlight its well-marked borders, such as kinetic
sculptures, kinetic art, cyber art, and cyberpunk. A brief excursion into the importance of the context, the message, and
its semiotics is also provided, case by case, together with a few hints on the history of this discipline in the light of
an artistic perspective. Therefore, the aim of this article is to try to summarize the main characteristics that might classify
robot art as a unique and innovative discipline, and to track down some of the principles by which a robotic artifact can
or cannot be considered an art piece in terms of social, cultural, and strictly artistic interest.
This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January
31–February 2, 2008 相似文献
19.
张涛 《计算机测量与控制》2015,23(1):86-89
为了设计一种具有低成本、低功耗、易操作、功能强且可靠性高的煤矿井下安全分站,针对煤矿安全生产实际,文章提出了采用MCS-51系列单片机为核心、具有CAN总线通信接口的煤矿井下安全监控分站的设计方案;首先给出煤矿井下安全监控分站的整体构架设计,然后着重阐述模拟量输入信号处理系统的设计过程,最后说明单片机最小系统及其键盘、显示、报警、通信等各个组成部分的设计;为验证设计方案的可行性与有效性,使用Proteus软件对设计内容进行仿真验证,设计的煤矿井下安全监控分站具有瓦斯、温度等模拟量参数超标报警功能和电机开停、风门开闭等开关量指示功能;仿真结果表明:设计的煤矿井下安全监控分站具有一定的实际应用价值. 相似文献
20.
Jacob Palme 《Software》1979,9(9):741-747
The COM teleconferencing system was designed to be easy to use for both beginners and people with much computer experience. A number of design choices in organizing the human-computer interface were considered very carefully. These design problems are not unique for teleconferencing applications, but will appear in many other developments of human-computer interfaces for non-computer specialists. This report discusses naming conventions, menu format, user commands, help facility and the treatment of ‘type ahead’ from the users. 相似文献