Incoherent Scatter Radar Probing of the 60-100-km Atmosphere and Ionosphere

All current incoherent backscatter radars can make mesospheric or D region measurements (60-90-km altitude) under at least some conditions. This paper, which is tutorial in nature, develops the basic concepts of incoherent scatter radar measurements in the D region and the conditions under which measurements are possible are derived and shown for each radar. Conditions examined include overall system sensitivity, electron and ion spectral line widths and power distributions, and time/height averaging effects. The appropriate form of the radar equation is derived and calibration of the radar system is discussed along with the various aspects of signal processing involved. Total power only and combined total power and ion line spectral measurements are described in terms of ease of use, applicability to various radars, and parameters of aeronomic interest derivable from the measurements.     

浅谈电力系统的安全性问题与防范措施

文中首先对电力系统的安全性问题进行了分析,进而对电力系统安全性问题的影响因素进行了探讨,最后提出了一系列关于电力系统安全性问题的有效防范措施。     

PON系统测试用光功率计

介绍了一种无源光网络(PON)系统中测试用的光功率计,该功率计通过特殊设计的光路和电路结构来实现PON系统中对信号光功率测试的特殊要求,即要满足线路上3种光信号波长的同时测试、在线测试和1310nm信号的突发测试功能,从而大大方便PON系统的安装、管理和维护。     

Millimeter-wave radar phenomenology of power lines and apolarimetric detection algorithm

The radar phenomenology of high-voltage power lines and cables is studied for examining the feasibility of detecting power lines along the path of a low-flying aircraft using a millimeter-wave radar system. For this purpose, polarimetric backscatter measurements of power line samples of different diameters and strand arrangements were performed over a wide range of incidence angles with very fine increments at 94 GHz. Also, similar polarimetric backscatter measurements were conducted for cylinders of the same radii and lengths as the power line samples for identifying the scattering features caused by the braiding structure of the power lines. In addition, the effects of a thin layer of water and a layer of ice over the power line surface on its polarimetric scattering behavior are studied by repeating the polarimetric backscatter measurements. Based on this phenomenological study, a polarimetric detection algorithm that makes use of the scattering features caused by the braided structure of power lines is proposed. It is shown that the proposed algorithm is capable of detecting power lines in a relatively strong clutter background with a poor signal-to-clutter ratio. The performance of the algorithm is demonstrated experimentally using a rough asphalt surface and a vegetation foliage as sample clutter backgrounds     

The Design of a Micro Power Management System for Applications Using Photovoltaic Cells With the Maximum Output Power Control

An inductor-less on-chip micro power management system for light energy harvesting applications is presented. We target at wide variety of applications that operate at different lighting environments ranging from strong sunlight to dim indoor lighting where the output voltage from the photovoltaic cells is low. A step-up charge pump is used to directly operate the circuit or to charge a rechargeable battery. The power management system operation is discussed and the control strategy for transferring the maximum output power from the power system is presented. Low power circuit design is proposed for the implementation of the system maximum output power control. The system was implemented using a 0.35-$muhbox{m}$ CMOS process. The chip was fabricated and measurements were conducted for different lighting conditions to demonstrate the system operation and verify the control strategy.      

IR thermography and FEM simulation analysis of on-chip temperature during thermal-cycling power-metal reliability testing using in situ heated structures

A calibrated system for power metal reliability analysis in smart power technology chips is presented. This system is mainly designed for temperature evaluation during temperature-cycling experiments. Infrared camera measurements under single shot high energy pulses are correlated with electro-thermal finite element simulation and failure analysis. A special test structure, containing poly-silicon heaters, is used to produce thermal stress. The location of a hot spot agrees well with the position of degraded power metal.     

PON系统测试用光功率计

文章介绍了一种无源光网络(PON)系统中测试用的光功率计,该功率计通过特殊设计的光路和电路结构来实现PON系统中对信号光功率测试的特殊要求,即要满足线路上3种光信号波长的同时测试、在线测试和1 310 nm信号的突发测试功能,从而大大方便PON系统的安装、管理和维护.     

Power Control Algorithms for Satellite Communication Systems

Three different ground terminal transmit power control concepts for a Satcom system are examined. The effectiveness of constant satellite power (CSP) sharing among the carriers and adaptive satellite power (ASP) sharing is compared with constant ground terminal transmit power (CTP). It is shown that ASP offers substantial advantages over CSP in combating environmental degradations and that both can increase link availability with respect to the constant power (CTP) case. The effectiveness of the ASP control technique is shown to depend on the interconnectivity of the network if multidestinational carriers are used. The measurements required for system control, as well as their accuracies, are described.     

Resource allocation for cellular radio systems

High terminal traffic densities are expected in urban multiuser radio systems. An efficient allocation of resources is the key to high system capacity. In this paper, a distributed dynamic resource allocation (DDRA) scheme based on local signal and interference measurements is proposed for multiuser radio networks. It offers “soft capacity” for time division multiple access (TDMA) and frequency division multiple access (FDMA) systems, bounded above by N per base station, where N is the total number of channels in the system. The decisions are made local to a terminal and its base and are essentially independent of the rest of the system. A distributed dynamic channel assignment scheme is used to assign channels to new calls. This scheme assigns a channel that offers the maximum carrier to interference ratio (CIR) to a new call. A distributed constrained power control (DCPC) scheme based on CIR measurements is used for power control. The channel assignment scheme and the power control scheme are coupled to obtain an interactive resource allocation scheme. We compare the capacity of a system which uses the distributed dynamic resource allocation scheme described above with the capacity of a system which uses the channel assignment scheme alone. The system capacity is measured by simulation as the number of terminals that can be served by the system with a CIR above an acceptable minimum. In a 1D cellular system, coupling the channel assignment scheme with power control is discussed. Simulations were also used to show the effect of varying the maximum transmitter power on system capacity     

A biosignal instrumentation system using capacitive coupling for power and signal isolation

Requirements for patient safety and a high interference rejection ratio in medical equipment create a demand for effective isolation devices. A system scale approach that uses capacitive coupling for power and signal isolation is presented. In addition, we describe the development of an instrumentation system prototype that applies microwaves for power exchange and bidirectional data transfer across the isolation barrier. The system consists of an isolated transducer unit, a central unit, and a single coaxial cable between the units. The isolation capacitance is as low as 1.6 pF, inclusive of the digital data transfer and power exchange up to 600 mW of isolated direct current (dc) power. The system is suitable for line-powered biopotential measurements and it is shown that reducing the isolation capacitance from 180 to 1.6 pF improves the power line rejection by 30 dB in a typical electrocardiogram (ECG) measurement setup.     

WACS-Wide-Area Stability and Voltage Control System: R&D and Online Demonstration

As background, we describe frequently used feedforward wide-area discontinuous power system stability controls. Then we describe online demonstration of a new response-based (feedback) Wide-Area stability and voltage Control System (WACS). The control system uses powerful discontinuous actions for power system stabilization. The control system comprises phasor measurements at many substations, fiber-optic communications, real-time deterministic computers, and transfer trip output signals to circuit breakers at many other substations and power plants. Finally, we describe future development of WACS. WACS is developed as a flexible platform to prevent blackouts and facilitate electrical commerce.     

An experimental study of the effects of harmonic loading onmicrowave MESFET oscillators and amplifiers

This paper reports an extensive experimental investigation of the effects of second harmonic loading on the performance of microwave GaAs MESFET oscillators; and strongly driven amplifiers. The measurement system used is an active load system based on six-port techniques. Harmonic load pull measurements were obtained for the NE72084 MESFET; the measurements show how the second harmonic load can influence the power gain and the power added efficiency in strongly driven amplifiers. The device line characterization technique was combined with the harmonic load pull technique; the measurement results illustrate how the output power and the DC to RF conversion efficiency of an oscillator depend on the choice of the second harmonic load. Amplifier and oscillator circuits have been designed using these measurements; the circuits have been constructed and measured. The results validate the experimental approach used and clearly illustrate the importance of properly selecting the second harmonic load in amplifier and oscillator circuits. Significant improvements in gain, output power and efficiency have been achieved by properly selecting the second harmonic load     

Measuring the real parameters of single-phase voltage source inverters for UPS systems

The design of a voltage source inverter (VSI) control system requires knowledge about its continuous or discrete model. The output filter inductance and the equivalent serial resistance, which is partly the result of power losses in the core, have values at the operating point that are significantly different from the assigned nominal values, particularly for iron-powder cores. Measurements using standard laboratory equipment are not sufficient because it is impossible to get the voltage and current of the operating point. So the best solution is to measure the Bode plots of the inverter control function at the operating point, to estimate the results of the measurements using the proper analytic function and to calculate the real values of the inverter parameters. Knowledge about the equivalent serial resistance enables the estimation of the inverter power losses. Two approaches to measurements are shown – one that does not require any additional equipment and the other that uses a specialised system to automatically measure the Bode plots. The advantages and disadvantages of both approaches are presented. These measurements enable the validation of the coil core magnetic material by taking into account the power losses. The applications of the measurements in the control design are shown.     

The measurement of a large antenna using a spacecraft as a receiver

Two computational methods for obtaining the gain pattern of a large antenna using power levels recorded by a spacecraft are developed from the transmission equation. Nominally, the large antenna is linearly polarized while the spacecraft's receiving antennas are circularly polarized. Since the spacecraft has no attitude control system, the orientation of the receiving antennas is not known a priori nor its orientation the same from orbit to orbit. The first method relies on an independent spacecraft attitude determination system to furnish the orientation of the receiving antennas. It combines this information with receiving-antenna gain measurements to give the power level of the incident radiation. Losses due to polarization mismatch are taken into account, but polarization loss factors are not actually computed. The second method relates simultaneous measurements made by separate channels with separate receiving antennas. By solving a system of equations numerically, one can determine the direction of the incident radiation as well as its power level. This alleviates the need for an attitude determination system. These methods originated in the operations of the spacecraft NUSAT1 (northern Utah Satellite)     

Optically Powered Remote Units for Radio-Over-Fiber Systems

Optically powered radio-over-fiber remote units have been designed and constructed for distributed antenna system applications using separate fibers for power and signal transmission. The feasibility of this approach has been investigated through a series of transmission measurements, based on the IEEE 802.11g wireless local area networking standard at a frequency of 2.5 GHz using 64-QAM OFDM modulation at 54 Mb/s. These measurements show that high-quality multilevel signal transmission is possible with modest levels of optical power at the central unit. For example, an EVM of around 3% has been achieved for an RF output power of 0 dBm using a central unit optical power of 250 mW over a link length of 300 m.      

Use of Satellite Technologies for Power System Measurements, Command, and Control

This paper analyzes the use of wide-area measurement technologies including satellite-based methods for the command and control of power systems. The methods studied include the global positioning system (GPS) and low earth orbit satellites (LEOS). Satellite technologies have been used in a variety of applications requiring precise timing between geographically diverse locations. The deregulation of the electric power industry is placing increased demands on power transmission system utilization. Because deregulated power systems utilize long-distance high-power exchanges, satellite-based communication systems are useful in control of geographically large interconnected power systems. In this paper, the satellite-based measurements and commands are introduced for wide-area control. With the support of wide-area signals, a multiagent supervisory-level power system stabilizer is proposed here as a potential wide-area control structure. Increased loading of transmission facilities is an impetus for accurate dynamic thermal overhead electrical conductor ratings. The application of satellite-based measurement for improving the dynamic thermal rating of overhead transmission circuits is suggested.     

100-GHz cooled amplifier residual PM and AM noise measurements, noise figure, and jitter calculations

We report the first definitive PM and AM noise measurements at 100 GHz of indium phosphide (InP) amplifiers operating at 5 K, 77 K, and room temperature. Amplifier gain ranged from +7 to +30 dB, depending on input RF power levels and operating bias current and gate voltages. The measurement system, calibration procedure, and amplifier configuration are described along with strategies for reducing the measurement system noise floor in order to accurately make these measurements. We compute amplifier noise figure with an ideal oscillator signal applied and, based on the PM noise measurements, obtain NF=0.8 dB, or a noise temperature of 59 K. Measurement uncertainty is estimated at /spl plusmn/0.3 dB. Results show that the use of the amplifier with an ideal 100-GHz reference oscillator would set a lower limit on rms clock jitter of 44.2 fs in a 20-ps sampling interval if the power into the amplifier were -31.6 dBm. For comparison, clock jitter is 16 fs with a commercial room-temperature amplifier operating in saturation with an input power of -6.4 dBm.     

基于虚拟仪器的直升机电源综合测试系统

介绍了一种直升机电源特性综合测试系统的设计方法,该系统采用现场总线测试技术,使用虚拟仪器编程语言LabWindows/CVI6.0设计了直升机各种供电特性参数的测试算法,实现了数据的多通道同时快速采集以及并行同步采集。虚拟仪器面板的交互式使用,使界面操作简单、便捷。实践证明该电源综合测试系统设计先进,稳定可靠,测试结果达到了要求的精度,可对被测对象的电气特性是否达到国军标要求进行评估。     

Low-power/low-voltage RF microsystems for wireless sensors networks

This paper presents radio-frequency (RF) microsystems (MSTs) composed by low-power devices for use in wireless sensors networks (WSNs). The RF CMOS transceiver is the main electronic system and its power consumption is a critical issue. Two RF CMOS transceivers with low-power and low-voltage supply were fabricated to operate in the 2.4 and 5.7 GHz ISM bands. The measurements made in the RF CMOS transceiver at 2.4 GHz, which showed a sensitivity of −60 dBm with a power consumption of 6.3 mW from 1.8 V supply. The measurements also showed that the transmitter delivers an output power of 0 dBm with a power consumption of 11.2 mW. The RF CMOS transceiver at 5.7 GHz has a total power consumption of 23 mW. The target application of these RF CMOS transceivers is for MSTs integration and for use as low-power nodes in WSNs to work during large periods of time without human operation, management and maintenance. These RF CMOS transceivers are also suitable for integration in thermoelectric energy scavenging MSTs.     

Bridging the gap between signal and power

Signal processing has been used in many different applications, including electric power systems. This is an important category, since a wide variety of digital measurements is available and data analysis is required to deliver diagnostic solutions and correlation with known behaviors. Measurements are taken at numerous locations, and the analysis of data applies to a variety of issues in ? power quality (PQ) and reliability ? power system and equipment diagnostics ? power system control ? power system protection. This article focuses on problems and issues related to PQ and power system diagnostics, in particular those where signal processing techniques are extremely important. PQ is a general term that describes the quality of voltage and current waveforms. PQ problems include all electric power problems or disturbances in the supply system that prevent end-user equipment from operating properly. Examples of voltage and current variations that can result in PQ problems include voltage interruptions, long- and short-duration voltage variations, steady-state research opportunities that use the measured voltages and currents to indicate possible equipment and system problems (referred to as equipment diagnostics).