η-Al2O3与γ-Al2O3在CS2催化水解反应中的性能比较

通过制备高纯度的前驱体湃铝石获得了η-Al₂O₃材料,采用XRD验证了η-Al₂O₃与γ-Al₂O₃在晶相结构上的差异,比较了两者的表面形貌、织构及酸碱性能,结果显示,η-Al₂O₃与γ-Al₂O₃的比表面积相当,但η-Al₂O₃具有更弱的弱碱位和较少的强碱位,并拥有丰富的中等强度酸性位。将η-Al₂O₃与γ-Al₂O₃作为催化剂应用于CS₂水解反应,结果表明,在(200~450) ℃测试温度范围内,η-Al₂O₃催化剂对CS₂的水解活性始终优于γ-Al₂O₃,两种催化剂上CS₂反应的浓度效应也明显不同,推测与它们的酸碱性质影响了对CS₂的吸附能力有关,导致两者催化CS₂水解反应遵循了不同的机制。     

制备条件对NiMo/γ-Al2O3催化剂上萘加氢生成四氢萘的影响

采用等体积浸渍法制备加氢催化剂NiMo/γ-Al₂O₃,在悬浮床上考察不同的制备条件下NiMo/γ-Al₂O₃对萘加氢生成四氢萘的影响。结果表明,催化剂的制备条件对加氢活性有显著的影响,NiMo/γ-Al₂O₃催化剂的最佳制备条件为共浸渍法负载金属组分Ni和Mo,在500 ℃的温度下焙烧4 h。此条件下制备的催化剂上四氢萘的选择性高达95.2%。     

Pt/Pt-Ce/γ-Al2O3催化氧化甲苯研究

通过等体积浸渍法制备单贵金属Pt/γ-Al₂O₃和双金属Pt-Ce/γ-Al₂O₃催化剂,考察Ce对催化剂活性的影响,确定催化剂最优配比。结果表明,当Pt的负载量为质量分数0.5%时,Pt/γ-Al₂O₃催化活性最高;当Pt的负载量为质量分数0.2%,Ce的负载量为质量分数1.0%时,Pt-Ce/γ-Al₂O₃催化剂的催化活性最高。Pt-Ce/γ-Al₂O₃催化剂的甲苯转化率高于Pt/γ-Al₂O₃催化剂。随着Pt负载量增大,催化剂孔容、孔径减小。粉体式催化剂性能优于整体式催化剂,但差别不大;Ce的添加有助于催化剂活性的提升。     

M/γ-Al2O3催化剂对煤油水重整制氢的影响

以γ-Al₂O₃为载体,采用等体积分步浸渍法制备了以Ni为活性组分,La、Ce、Fe、Cr、Co为助剂的催化剂M/γ-Al₂O₃,在固定床管式反应器中研究了M/γ-Al₂O₃催化剂的性能,考察了反应温度、水碳比和空速对氢产率的影响,并对催化剂进行XRD、SEM和BET表征。结果表明,NiLaCeFeCrCo/γ-Al₂O₃催化剂具有较好的催化性能,在反应温度700 ℃、水碳物质的量比10和空速6 min^-1的条件下,氢产率达到27.335 mol·mol^-1,并在300 min内表现出较好的活性,平均氢产率为21.966 mol·mol^-1。     

大豆油制备生物柴油K2CO3/SiO2固体碱催化剂性能研究

采用浸渍法制备了K₂CO₃/SiO₂固体碱催化剂，运用X射线粉末衍射仪对催化剂进行了分析表征。探究了反应时间、K₂CO₃负载量、醇油物质的量比、焙烧温度、催化剂用量和焙烧时间6个因素对生物柴油产率的影响。探究结果显示，在大豆油制取生物柴油时，最优的条件是：K₂CO₃负载量70%、焙烧温度600℃、焙烧时间4 h、反应时间是4 h、催化剂用量3%、醇油物质的量比9∶1。此时产物的产率是94.7%。     

低成本大比表面积γ-Al2O3的制备

以廉价无机铝盐硫酸铝为原料,氨水为沉淀剂,十二烷基硫酸钠为添加剂,采用简单沉淀法制备得到较大比表面积γ-Al₂O₃。通过N₂低温物理吸附-脱附、X射线衍射、红外光谱、热重、元素分析、扫描及透射电镜等,研究制备过程中沉淀温度、溶液pH值和添加剂用量对产物γ-Al₂O₃及其前驱体的晶相结构、形貌织构等性质的影响。结果表明,在沉淀温度75 ℃、硫酸铝浓度0.25 mol·L^-1、溶液pH=9.0、老化时间12 h和n(十二烷基硫酸钠)∶n[Al₂(SO₄)₃]=0.375∶1条件下,所得前驱体(拟薄水铝石)经600 ℃焙烧后,可获得大比表面积(416.65 m²·g^-1)γ-Al₂O₃,并且样品中因十二烷基硫酸钠添加,引入的S及Na等杂质含量极少。     

B2O3改性Na2CO3催化剂用于甲醇脱氢制无水甲醛

以B₂O₃为助催化剂,采用研磨混合法改性Na₂CO₃催化剂,在固定床反应器中催化甲醇脱氢制备无水甲醛,考察催化剂的组成和反应条件等对催化反应的影响,采用XRD、TG-DTG、N₂吸附-脱附、SEM和CO₂-TPD等对催化剂进行表征。结果表明,以B₂O₃为助催化剂采用机械研磨混合法改性的Na₂CO₃催化剂,增加了催化剂的比表面积,在(10～30) nm增加了大量的孔道,平均孔径达18.44 nm,比表面积为1.65 m²·g^-1,且B₂O₃分布均匀,改性后的催化剂碱性降低,在催化甲醇脱氢制备无水甲醛的反应中,催化活性明显高于Na₂CO₃催化剂,表明B₂O₃改性Na₂CO₃催化剂能提高甲醇转化率和甲醛选择性。在B₂O₃/Na₂CO₃催化剂中B₂O₃质量分数为30%、甲醇进料质量分数为26%、反应温度为650 ℃和甲醇重时空速为2.94 h^-1条件下,甲醇转化率达59.97%,甲醛选择性达83.28%。     

负载型K2CO3/Al2O3吸收剂吸收CO2反应机理

利用热重分析仪、扫描电镜和氮吸附仪对不同粒径的K₂CO₃颗粒和负载型K₂CO₃/Al₂O₃二氧化碳吸收剂的碳酸化特性进行研究。负载后的吸收剂比表面积和孔隙结构得到较大改善,使得碳酸化反应速率和转化率均提高,吸收剂碳酸化特性得到改善。纯K₂CO₃颗粒吸收剂的反应速率和转化率随着粒径的增加而减小,负载型吸收剂的反应速率和转化率随着粒径的增加略增大。研究了不同粒径和反应时间对K₂CO₃/Al₂O₃颗粒微观结构的影响,结果表明K₂CO₃/Al₂O₃颗粒具有较稳定的微观结构。采用负载型粒子模型对K₂CO₃/Al₂O₃吸收剂吸收CO₂碳酸化过程进行研究,所建立的粒子模型计算结果与试验值吻合较好。利用建立的模型对不同CO₂浓度下K₂CO₃/Al₂O₃吸收剂碳酸化反应特性进行模拟计算,模拟结果具备一定的合理性和准确性,为开展进一步研究提供了基础。     

Ni(OH)2修饰对a-Fe2O3薄膜光电化学性能的增强效应

利用一种简便的电沉积方法制备氧化铁薄膜,并在过程中引入Ni(OH)₂进行修饰,对具体电沉积实验参数进行优化,从而建立最佳制备条件。利用场发射扫描电子显微镜、X射线粉末衍射对Fe₂O₃/Ni(OH)₂光电极膜的结构进行表征。利用循环伏安和计时电流测量析氧过电位和光电流密度。结果表明,Ni(OH)₂修饰的α-Fe₂O₃薄膜可提高光生电子与空穴的分离效率,从而显著提高光电催化活性。     

SO42-/TiO2/Al2O3型固体酸制备及催化合成醋酸丁酯

以共沉淀-浸渍法制备了SO₄^2-/TiO₂/Al₂O₃型固体酸催化剂,醋酸与正丁醇酯化反应作为探针反应,考察SO₄^2-/TiO₂/Al₂O₃型固体酸催化剂的催化性能,采用响应面法对制备催化剂过程中的陈化温度、硫酸浸渍液浓度和焙烧温度因素进行优化,通过XRD和IR对制备的固体酸催化剂进行表征。结果表明,在陈化温度-4 ℃、硫酸浸渍液浓度1.48 moL·L^-1和焙烧温度586 ℃条件下制得的催化剂催化性能最高,醋酸正丁酯酯化率可达98.1%,重复使用性良好。     

CO气相偶联合成草酸二甲酯Pd/α-Al2O3催化剂失活与再利用

作为合成气制乙二醇关键步骤之一,CO与亚硝酸甲酯合成草酸二甲酯备受关注。综述了近年来CO气相偶联合成草酸二甲酯Pd/α-Al₂O₃催化剂失活与再利用研究进展,探讨催化剂再利用工艺存在的问题,指出应根据在工业应用中出现的问题对Pd/α-Al₂O₃催化剂进行失活研究,在此基础上开发针对性的再生工艺;钯催化剂回收方面萃取法和吸附法逐渐成为研究重点,高效、低耗、短流程绿色工艺的开发是失活钯催化剂再利用的发展方向。     

Carbon formation and its influence on ethanol steam reforming over Ni/Al2O3 catalysts

Ethanol steam reforming was studied over Ni/Al₂O₃ catalysts. The effect of support (- and γ-Al₂O₃), metal loading and a comparison between conventional H₂ reduction with an activation method employing a CH₄/O₂ mixture was investigated. The properties of catalysts were studied by N₂ physisorption, X-ray diffraction (XRD) and temperature programmed reduction (TPR). After activity tests, the catalysts were analyzed by scanning electron microscopy (SEM) and thermogravimetric analysis (TG/DTA). Ni supported on γ-Al₂O₃ was more active for H₂ production than the catalyst supported on -Al₂O₃. Metal loading did not affect the catalytic performance. The alternative activation method with CH₄/O₂ mixture affected differently the activity and stability of the Ni/γ-Al₂O₃ and the Ni/-Al₂O₃ catalyst. This activation method increased significantly the stability of Ni/-Al₂O₃ compared to H₂ reduction. SEM and TG/DTA analysis indicate the formation of filamentous carbon during the CH₄/O₂ activation step, which is associated with the increasing catalyst activity and stability. The effect of temperature on the type of carbon formed was investigated; indicating that filamentous coke increased activity while encapsulating coke promoted deactivation. A discussion about carbon formation and the influence on the activity is presented.     

NO reduction by CH4 in the presence of O2 over La2O3 supported on Al2O3

Dispersing La₂O₃ on δ- or γ-Al₂O₃ significantly enhances the rate of NO reduction by CH₄ in 1% O₂, compared to unsupported La₂O₃. Typically, no bend-over in activity occurs between 500° and 700°C, and the rate at 700°C is 60% higher than that with a Co/ZSM-5 catalyst. The final activity was dependent upon the La₂O₃ precursor used, the pretreatment, and the La₂O₃ loading. The most active family of catalysts consisted of La₂O₃ on γ-Al₂O₃ prepared with lanthanum acetate and calcined at 750°C for 10 h. A maximum in rate (mol/s/g) and specific activity (mol/s/m²) occurred between the addition of one and two theoretical monolayers of La₂O₃ on the γ-Al₂O₃ surface. The best catalyst, 40% La₂O₃/γ-Al₂O₃, had a turnover frequency at 700°C of 0.05 s⁻¹, based on NO chemisorption at 25°C, which was 15 times higher than that for Co/ZSM-5. These La₂O₃/Al₂O₃ catalysts exhibited stable activity under high conversion conditions as well as high CH₄ selectivity (CH₄ + NO vs. CH₄ + O₂). The addition of Sr to a 20% La₂O₃/γ-Al₂O₃ sample increased activity, and a maximum rate enhancement of 45% was obtained at a SrO loading of 5%. In contrast, addition of SO⁼₄ to the latter Sr-promoted La₂O₃/Al₂O₃ catalyst decreased activity although sulfate increased the activity of Sr-promoted La₂O₃. Dispersing La₂O₃ on SiO₂ produced catalysts with extremely low specific activities, and rates were even lower than with pure La₂O₃. This is presumably due to water sensitivity and silicate formation. The La₂O₃/Al₂O₃ catalysts are anticipated to show sufficient hydrothermal stability to allow their use in certain high-temperature applications.     

Deactivation studies over NiO/γ-Al2O3 catalysts for partial oxidation of methane to syngas

Two types of NiO/γ-Al₂O₃ catalysts prepared by the impregnation and the sol–gel method were used for the partial oxidation of methane to syngas at 850°C (GHSV1.8×10⁵ lkg⁻¹ h⁻¹). The effects of the carbon deposition, the loss and sintering of nickel and the phase transformation of γ-Al₂O₃ support on the catalytic performance during 80 h POM reaction were investigated with a series of characterization such as XRD, BET, AAS, TG, and XPS. The results indicated that the carbon deposition and the loss and sintering of nickel could not cause the serious decrease of catalytic performance over NiO/γ-Al₂O₃ catalyst during the short-time reaction. However, the slow process of the support γ-Al₂O₃ phase transforming into -Al₂O₃ could slowly decrease the performance of NiO/γ-Al₂O₃ catalysts. Aimed at the reasons of the deactivation, an improved catalyst was obtained by the complexing agent-assisted sol–gel method.     

Performance and characterization of Ru/Al2O3 and Ru/SiO2 catalysts modified with Mn for Fischer–Tropsch synthesis

Mn effect and characterization on γ-Al₂O₃-, -Al₂O₃- and SiO₂-supported Ru catalysts were investigated for Fischer–Tropsch synthesis under pressurized conditions. In the slurry phase Fischer–Tropsch reaction, γ-Al₂O₃ catalysts showed higher performance on CO conversion and C₅⁺ selectivity than -Al₂O₃ and SiO₂ catalysts. Moreover, Ru/Mn/γ-Al₂O₃ exhibited high resistance to catalyst deactivation and other catalysts were deactivated during the reaction. From characterization results on XRD, TPR, TEM, XPS and pore distribution, Ru particles were clearly observed over the catalysts, and γ-Al₂O₃ catalysts showed a moderate pore and particle size such as 8 nm, where -Al₂O₃ and SiO₂ showed highly dispersed ruthenium particles. The addition of Mn to γ-Al₂O₃ enhanced the removal of chloride from RuCl₃, which can lead to the formation of metallic Ru with moderate particle size, which would be an active site for Fischer–Tropsch reaction. Concomitantly, manganese chloride is formed. These schemes can be assigned to the stable nature of Ru/Mn/γ-Al₂O₃ catalyst.