Combustion characteristics of Turkish lignites at oxygen-enriched and oxy-fuel combustion conditions

Combustion and oxy-fuel combustion characteristics of two Turkish lignites (Orhaneli and Soma) were investigated by Thermogravimetric Analysis (TGA) method. Experiments were carried out under oxygen-enriched air and oxy-fuel combustion conditions with 21, 30, 40% oxygen concentrations. Three heating rates of 5, 10, and 20 °C/min were considered and the isoconversional kinetic methods of FWO, KAS, and Friedman were employed to estimate activation energies. The uncertainty assessment in obtaining the activation energy values was also considered. The obtained results indicated that the combustion of volatiles at both air and oxy-fuel conditions were approximately identical. However, at air combustion conditions, the decomposition of CaCO₃ took place at temperatures above 700 °C. This decomposition process was independent of the oxygen concentration and took place when the temperature reached to a certain threshold. The decomposition of CaCO₃ did not accomplish in oxy-fuel conditions as far as the temperature was higher than 900 °C. Combustion in oxy-fuel conditions had higher activation energy values comparing to conventional combustion atmosphere. The activation energy values were approximately unchanged at the start of combustion regardless of oxygen concentration or combustion atmosphere at about 165 kJ/mol and 150 kJ/mol for Orhaneli and Soma lignites, respectively. The apparent activation energies were higher at elevated oxygen concentrations. The uncertainties values related to FWO method were lower than KAS and Friedman methods. The calculated average uncertainty values were found to be at the range of 5–15% for most of the cases.     

TGA and kinetic study of different torrefaction conditions of wood biomass under air and oxy-fuel combustion atmospheres

Combustion and oxy-fuel combustion characteristics of torrefied pine wood chips were investigated by Thermogravimetric Analysis (TGA). Three torrefaction temperatures (250, 300, and 350 °C) and two residence times (15 and 30 min) were considered. Experiments were carried out at three heating rates of 10, 20, and 40 °C/min. The isoconversional kinetic methods of FWO, KAS, and Friedman were employed to estimate the activation energies. The assessment of uncertainty in obtaining the activation energy values was also considered. The obtained results indicated that due to torrefaction, the O/C and H/C atomic ratios decreased, resulting the 300ºC-30 min and 350ºC-15 min torrefied biomass to be completely embedded in lignite region in van-Krevelen's diagram. Oxy-fuel combustion affected the decomposition of cellulose and lignin components of biomass while the impact on the hemicellulose component was negligible. The kinetic analysis revealed that with the evolution of conversion degree, the activation energy values increased during hemicellulose degradation, remained approximately constant during cellulose decomposition and showed a sharp decrease for lignin decomposition. The activation energy trends were comparable in both air and oxy-fuel combustion conditions, however slight changes in activation energy values were noticed. The highest activation energy value was obtained for 250ºC-30 min torrefied biomass at 183.40 kJ/mol and the lowest value was 72.93 kJ/mol for 350ºC-15 min biomass. The uncertainty values related to FWO method were lower than KAS and Friedman methods. The uncertainty values for FWO and KAS methods were at the range of 5–15%.     

Study on the limestone sulfation behavior under oxy-fuel circulating fluidized bed combustion condition

In order to investigate the behavior of limestone sulfation under oxy-fuel circulating fluidized bed (CFB) combustion condition, experiments were conducted in a 50 kW oxy-fuel CFB system under the O₂/CO₂ and air combustion conditions. A small cage, containing limestone particles, was dipped into the dense zone of the CFB combustor during the experiments. The calcination of limestone, pore structure of the product layer, and calcium conversion were studied. It was found that the increasing of temperature would promote the calcination of limestone and the high concentration of CO₂ would inhibit calcination of limestone. The formation process of the product layer was completely different between the direct and indirect sulfation, while it was almost the same during the indirect sulfation under the oxy-fuel and air combustion. However, both the temperature and gas compositions played important roles in determining the pore structures of the product layer during the limestone indirect sulfation process. Under the O₂/CO₂ combustion condition, the calcium conversion of indirect sulfation was always higher than that of direct sulfation. The highest final calcium conversion after 60 min was found at 900 °C under the O₂/CO₂ combustion condition.     

Formation and O2/CO2 combustion characteristics of real-environment coal char in high-temperature oxy-fuel conditions

Oxygen-fuel combustion is a promising technology for CO₂ emission reduction. The high-temperature entrained flow reactor and high-temperature drop tube furnace were used to analyses the formation and O₂/CO₂ combustion characteristics of real-environment coal char in high-temperature oxy-fuel conditions. It proposed “inflection point standard” of high-temperature flame method for the preparation of real-environmental oxy-fuel coal char according to the flame method. The results show that the ratios of C=O/C-O and C=O/C_ar increase in the coal char compared with the raw coals. The trend of C=O/C_ar in oxy-fuel condition is opposite to that in the inert atmosphere, due to the effect of high-concentration CO₂. To achieve the burnout rate similar to air combustion for coal char, with the increase of coal rank, the O₂ concentration should be enhanced. The optimal O₂ concentration for the oxy-fuel combustion of JC anthracite is 30%, while that of other low-rank coals could be lower than 30%. The combustion characteristic of JC anthracite is with the highest sensitivity to temperature and O₂ concentration.     

HCl emission and capture characteristics during PVC and food waste combustion in CO2/O2 atmosphere

The emission and capture characteristics of HCl during PVC and food waste combustion in CO₂/O₂ atmospheres were studied. Replacement of N₂ by CO₂ decreased the dechlorination rate of limestone at 600–700 °C but increased dechlorination rate at 800–900 °C. The chlorine species and temperature highly influenced the HCl emission and capture efficiency of limestone for HCl in CO₂/O₂ atmospheres. Compared with inorganic chloride in food waste, organic chlorine in PVC had much greater Cl–HCl conversion percent (75.0–93.9%), and higher dechlorination rate (20.4–44.9%) with 10% limestone in 80CO₂/20O₂ atmosphere. The increment of O₂ partial pressure in CO₂/O₂ atmospheres promoted Cl–HCl conversion. Sulphur in the fuel suppressed the formation of HCl but decreased the dechlorination rate at 700–1000 °C in CO₂/O₂ atmospheres. The dechlorination efficiency of limestone was better than magnesium based additive and could be improved by modification with NaOH. This research helps control HCl and manages MSW oxy-fuel incineration.     

Effect of different conditions on the combustion interactions of blended coals in O2/CO2 mixtures

The combination of oxy-fuel and blended-coal combustion may be one of these effective methods to both reduce CO₂ emissions and improve energy utilization efficiency in coal-fired power stations. The aim of this study is to investigate oxy-fuel combustion interactions of blended coals under different conditions using a thermo-gravimetric analyzer. The results show that compared with those in an O₂/N₂ mixture, the promotive and inhibitive effect and the comprehensive interactions are considerably weaker in an O₂/CO₂ mixture. In the O₂/CO₂ mixture, both increasing the O₂ concentration and decreasing the particle size result in decreasing the promotive effect but increasing the inhibitive effect and the comprehensive interactions, which increase the non-additive combustion characteristics. Enhancement of the heating rate increases the promotive effect but decreases the inhibitive effect and the comprehensive interactions, which weaken the non-additive combustion characteristics. Of these factors, the effects of the oxygen concentration and heating rate on comprehensive interactions are greater than that of particle size. This study provides useful information for the design and optimization of thermo-chemical conversion systems of coal blends in the O₂/CO₂ atmosphere.     

Thermal decomposition behavior of tobacco stem Part II: Kinetic analysis

As a continuation of the previous study on the thermal degradation behavior of tobacco stem, this work is focused on the kinetics of pyrolytic decomposition. Thermogravimetric analysis of tobacco stem samples was conducted under nitrogen atmosphere at different heating rates of 5, 10, 15, and 20°C/min at a temperature range of 25–1,000°C. The kinetic parameters, such as activation energy, pre-exponential factor, and reaction order, were determined by applying the Coats–Redfern method for the main pyrolysis occurred in the second zone by means of the decomposition of hemicellulose, cellulose, and lignin at a temperature range 180–540°C. In addition, the activation energy was calculated using various degradation models, including Kissinger, Friedman (FR), Flynn–Wall–Ozawa (FWO), and Kissinger–Akahira–Sunose (KAS). The average activation energy of tobacco stem was calculated to be 150.40, 230.76, 216.97, and 218.56 kJ/mol by the Kissinger, FR, FWO, and KAS models, respectively.     

Comparative study on combustion and oxy-fuel combustion environments using mixtures of coal with sugarcane bagasse and biomass sorghum bagasse by the thermogravimetric analysis

Biomass and coal have different physicochemical properties and thermal behavior. During the co-combustion of coal-biomass mixtures, their thermal behavior varies according to the percentage of each fuel in the mixture. Thereby, this research aims to characterize the thermal behavior of mixtures of coal, sugarcane bagasse, and biomass sorghum bagasse as biomass in simulated combustion (O₂/N₂) and oxy-fuel combustion (O₂/CO₂) environments. Experiments have been performed in duplicate on a thermogravimetric analyzer at heating rate of 10 °C/min. A uniform granulometry was considered for all materials (63 μm) in order to ensure a homogeneous mixture. Four biomass percentages in the mixture (10, 25, 50 and 75%) have been studied. Based on thermogravimetric (TG) and thermogravimetric (DTG) analyses, parameters such as combustion index, synergism, and activation energy have been determined, as well as the combustion environment influence on these parameters. The results indicate that, although sugarcane bagasse has the lowest activation energy, the thermal behavior of both types of biomass is similar. Thus, biomass sorghum bagasse can be used as an alternative biomass to supply the power required during sugarcane off-season. For both mixtures, optimal results were obtained at 25% of biomass. By analyzing the environment influence on combustion behavior, the results indicate that when N₂ is replaced with CO₂, it is observed an increase in reaction reactivity, a higher oxidation rate of materials and an improvement in evaluated parameters.     

Reactivity of pulverized coals during combustion catalyzed by CeO2 and Fe2O3

Effects of CeO₂ and Fe₂O₃ on combustion reactivity of several fuels, including three ranks of coals, graphite and anthracite chars, were investigated using thermo-gravimetric analyzer. The results indicated that the combustion reactivity of all the samples except lignite was improved with CeO₂ or Fe₂O₃ addition. It was interesting to note that the ignition temperatures of anthracite were decreased by 50 °C and 53 °C, respectively, with CeO₂ and Fe₂O₃ addition and that its combustion rates were increased to 15.4%/min and 12.2%/min. Ignition temperatures of lignite with CeO₂ and Fe₂O₃ addition were 250 °C and 226 °C, and the combustion rates were 12.8% and 19.3%/min, respectively. When compared with those of lignite without catalysts, no obvious catalytic effects of the two catalysts on its combustion reactivity were revealed. The results from the combustion of the three rank pulverized coals catalyzed by CeO₂ and Fe₂O₃ indicated significant effects of the two catalysts on fixed carbon combustion. And it was found that the higher the fuel rank, the better the catalytic effect. The results of combustion from two kinds of anthracite chars showed obvious effects of anthracite pyrolysis catalyzed by CeO₂ and Fe₂O₃ on its combustion reactivity.     

The study of co-combustion characteristics of coal and microalgae by single particle combustion and TGA methods

The co-combustion characteristics of coal and microalgae with different blending ratios and under different atmospheres are studied by single particle combustion and thermogravimetric analysis methods. The combustion processes of coal, microalgae and their blends in the single particle combustion experiment have two stages, while the combustion process of coal in the thermogravimetric analysis experiment only has one stage. With the increasing blending ratio of microalgae, flames of volatiles and char of fuels become dimmer and smaller, and the average flame temperature decreases from about 1400 °C to about 1200 °C. The ignition delay time decreases from 200 ms to 140 ms, and the experimental ignition delay time of blended fuels is lower than the theoretical ignition delay time, which demonstrates that the synthetic effect between coal and microalgae exists. To analyze the influence of oxy-fuel atmosphere on the combustion characteristics, the air is replaced by the O₂/CO₂ atmosphere. The replacement decreases the luminosity, size and average temperature of flames. The average flame temperature of volatiles decreases from 1449.4 °C to 1151.2 °C, and that of char decreases from 1240.0 °C to 1213.4 °C. The replacement increases the ignition delay time of fuel from 80 ms to 100 ms. Increasing mole fraction of O₂ in O₂/CO₂ atmosphere can offset these influences. With the increasing mole fraction of O₂, flames of volatiles and char of fuels become brighter and larger, the average flame temperature increases from about 1100 °C to about 1300 °C, while the ignition delay time decreases from 100 ms to 77 ms.     

Conversions of fuel-N to NO and N2O during devolatilization and char combustion stages of a single coal particle under oxy-fuel fluidized bed conditions

The conversions of fuel-N to NO and N₂O during devolatilization and char combustion stages of a single coal particle of 7 mm in diameter were investigated in a laboratory-scale flow tube reactor under oxy-fuel fluidized bed (FB) conditions. The method of isothermal thermo-gravimetric analysis (TGA) combing with the coal properties was proposed to distinguish the devolatilization and char combustion stages of coal combustion. The results show that the char combustion stage plays a dominant role in NO and N₂O emissions in oxy-fuel FB combustion. Temperature changes the trade-off between NO and N₂O during the two stages. With increasing temperature, the conversion ratios of fuel-N to NO during the two stages increase, and the opposite tendencies are observed for N₂O. CO₂ inhibits the fuel-N conversions to NO during the two stages but promotes those to N₂O. Compared with air combustion, the conversion ratios of fuel-N to NO during the two stages are lower in 21%O₂/79%CO₂, and those to N₂O are higher. At <O₂> = 21–50% by volume, the conversion ratios of fuel-N to NO during the two stages reach the maximum values at <O₂> = 30% by volume, and those to N₂O decrease with increasing O₂ concentration. H₂O suppresses the fuel-N conversions to NO and N₂O during the two stages. A higher coal rank has higher total conversion ratios of fuel-N to NO and N₂O. Fuel-N, volatile matter, and fixed carbon contents are the important factors on fuel-N conversions to NO and N₂O during the two stages. The results benefit the understanding of NO and N₂O emission mechanisms during oxy-fuel FB combustion of coal.     

Thermogravimetric analysis of microalgae combustion under different oxygen supply concentrations

Recently, studies of microalgae in China have increased a lot because of their obvious advantages over other biological fuels. In this paper, the combustion behavior of Chlorella vulgaris (a genus of unicellular green microalgae) was investigated in a thermogravimetric analyzer (TGA) from room temperature to 800 °C in O₂/N₂ atmospheres. The effects of different oxygen concentrations (20, 50, 60, 80 vol.%) and different heating rates (10, 20 and 40 °C min⁻¹) on the combustion processes of C. vulgaris had been studied. The results indicated that the combustion processes of C. vulgaris could be divided into three stages. The oxygen concentrations and heating rates had important effects on the main combustion processes of C. vulgaris. The iso-conversional method involving Flynn–Wall–Ozawa (FWO) and the Kissinger–Akahira–Sunose (KAS) methods were used for the kinetic analysis of the main combustion process. The results indicated that, when the oxygen concentration varied from 20 to 80 vol.%, the value of activation energy increased respectively from 134.03 to 241.04 kJ mol⁻¹ by using FWO method and from 134.53 to 242.33 kJ mol⁻¹ by KAS method. Moreover, the optimal oxygen concentration for C. vulgaris combustion was 25–35 vol.%_.     

Detailed investigation of NO mechanism in non-premixed oxy-fuel jet flames with CH4/H2 fuel blends

This study systematically investigates the detailed mechanism of nitrogen oxides (NO_x) in CH₄ and CH₄/H₂ jet flames with O₂/CO₂ hot coflow. After comprehensive validation of the modeling by experiments of Dally et al. [Proc. Combust. Inst. 29 (2002) 1147–1154]; the effects of CO₂ replacement of N₂, mass fraction of oxygen in the coflow (Y_O2), and mass fraction of hydrogen in the fuel jet (Y_H2) on NO formation and destruction are investigated in detail. For methane oxy-fuel combustion, the NNH route is found to control the NO formation at Y_O2 ≤ 3%, while both NNH and N₂O-intermediate routes dominate the NO production at 3% < Y_O2 < 10%. When Y_O2 ≥ 10%, NO is obtained mainly from thermal mechanism. Moreover, in the oxy-combustion of methane and hydrogen fuel blends with Y_O2 = 3%, with hydrogen addition the contribution of the NNH and prompt routes increases, while that of the N₂O-intermediate route decreases. Furthermore, the chemical effect of CO₂ is significant in reducing NO in both oxy-combustion of methane with Y_O2 ≤ 3% and combustion of methane and hydrogen fuel blends with Y_H2 ≤ 10%.     

Vanadium-ceria catalysts for H2S abatement from biogas to feed to MCFC

Vanadium-based catalysts supported on ceria were studied for the direct and selective oxidation of H₂S to sulphur and water at low temperature.Catalysts with two vanadium loading (20–50 wt% of V₂O₅) were prepared, characterized and tested at temperature of 150–200 °C in order to identify the best catalytic formulation. The most promising catalyst was the sample with the 20 wt% of V₂O₅ that showed 99% of sulphur selectivity and equilibrium H₂S conversion at 150 °C.The effect of the components of a typical biogas stream (CH₄, CO₂ and H₂O) was studied at 150 °C in order to investigate the possible formation of secondary products such COS, CS₂. No significant effect was observed in terms of H₂S conversion (99%) and selectivity to SO₂ (<1%) by adding CH₄ and CO₂ to the feed stream. Furthermore, the effect of the H₂S inlet concentration, temperature, contact time and molar feed ratio (O₂/H₂S) were also investigated at a reaction temperature of 80 °C.Finally, time on stream tests of 30 h were performed at 80 and 120 °C, in order to examine the catalyst stability.     

Perovskite Sr(Fe1-xCux)O3-δ materials for chemical looping combustion applications

This paper presents the results of chemical looping combustion (CLC) research. Nowadays, CLC is one of the best prospective combustion technologies, because it enables the production of a concentrated carbon dioxide (CO₂) stream, following water condensation, without any energy penalty for its separation.The objective of this work was to study chemical looping reaction performance with the application of novel perovskite-type oxygen carriers (OCs). Sr(Fe_1-xCu_x)O_3-δ family members were tested for hydrogen combustion for power generation purposes. Sr(Fe_1-xCu_x)O_3-δ, which is a perovskite-type oxide, was prepared using the calcination method, where x = 0, 0.1 and 0.33. Reactivity tests were performed using a thermogravimetric analyser (TGA, Netzsch STA 409 PG Luxx) under isothermal conditions in multiple reduction–oxidation cycles. Both the temperature (600–800 °C) and number of redox cycles (five cycles) effects on the reaction performance of recently developed OC samples were evaluated in the study. TGA data were used for the assessment of the oxygen transport capacity value, redox reaction rates and stability. Sr(Fe_1-xCu_x)O_3-δ showed an excellent stable chemical looping performance. The changing of oxygen content (3.8–4.86 wt%) occurred within approximately 2 min, with the chemical properties of the material maintained during the cycling combustion tests.In addition, new SrFeO_3-δ OCs, doped with copper (Cu) perovskite-type materials, were analysed using multiple methods: X-ray powder diffraction (XRD); scanning electron microscopy (SEM); surface area by Brunauer–Emmett–Teller (BET) method; and melting behaviour study. In terms of physical properties, the new OCs can resist both high CLC process temperatures and mechanical forces, which are essentially useful. The analysis showed that Sr(Fe_1-xCu_x)O_3-δ carriers performed at extremely high melting temperatures (>1280 °C). Results of crushing strength testing showed that developed materials had a pronounced mechanical resistivity with a crushing strength higher than 1 N and will perform well in fluidized beds (4.31–6.23 N).In this paper, it was demonstrated that known mixed oxygen-ionic and electronic conducting membrane materials such as Sr(Fe_1-xCu_x)O_3-δ might also be applied as oxygen carriers. Overall results demonstrated Fe-Cu-based perovskites might be successfully used as OCs in the chemical looping combustion process.     

Experimental investigation of ignition and combustion characteristics of single coal and biomass particles in O2/N2 and O2/H2O

Oxy-steam combustion is a potential new-generation option for CO₂ capture and storage. The ignition and combustion characteristics of single coal and biomass particles were investigated in a flow tube reactor in O₂/N₂ and O₂/H₂O at various oxygen concentrations. The ignition and combustion processes were recorded using a CCD camera, and the two-color pyrometry was used to estimate the volatile flame temperature and char combustion temperature. In O₂/N₂ and O₂/H₂O, coal ignites heterogeneously at <O₂> = 21–50%. In O₂/N₂, biomass ignites homogeneously at <O₂> = 21–30%, while it ignites heterogeneously at <O₂> = 40–50%. In O₂/H₂O, biomass ignites homogeneously at <O₂> = 21–50%. With increasing oxygen concentration, the ignition delay time, volatile burnout time and char burnout time are decreased, and the volatile flame temperature and char combustion temperature are increased. At a certain oxygen concentration in both atmospheres, the ignition delay time, volatile burnout time and char burnout time of biomass are shorter than those of coal. Moreover, biomass has a higher volatile flame temperature but a lower char combustion temperature than coal. The ignition delay time, volatile burnout time and char burnout time in O₂/H₂O are lower than those in O₂/N₂ for coal and biomass. The presence of H₂O can improve the combustion rates of coal and biomass. The volatile flame shows a lower temperature in O₂/H₂O than in O₂/N₂ at <O₂> = 21–50%. The char combustion shows a lower temperature in O₂/H₂O than in O₂/N₂ at <O₂> = 21–30%, while this behavior is switched at <O₂> = 40–50%. The results contribute to the understanding of the ignition and combustion characteristics of coal and biomass in oxy-steam combustion.     

The influence of the addition of sodium on the transformation of alkali and alkaline-earth metals during oxy-fuel combustion

Alkali and alkaline-earth metals (AAEM) of coal directly affect the coal combustion properties and ash formation during coal oxy-fuel combustion. To further understand the influence of adding sodium on the transformation of AAEM, sodium chloride (NaCl) and sodium acetate (NaAc) were added to Shenmu coal in this study. A drop-tube reactor and ion chromatography were adopted in this study and a serial dissolution method was used to clarify the occurrence modes of the AAEM. The results showed that all types of AAEM can release and the release rates were increased with an increase in temperature during oxy-fuel combustion. Water-soluble (W-type) alkali metals react with SiO₂ and Al₂O₃ in coal and are converted into acid-soluble (H-type) silicate or acid-insoluble (I-type) aluminosilicate under certain experimental conditions. The addition of sodium can promote the release of AAEM via promoting coal combustion; the promotion effect was significant at 600 °C, and the effect of NaCl was more noticeable than that of NaAc. Furthermore, the promoting effect on alkali metals was more noticeable than that on alkali-earth metals. The added sodium can also react with SiO₂ and Al₂O₃ to form H-type sodium silicate or I-type sodium aluminosilicate.     

Experimental study on ash deposition of Zhundong coal in oxy-fuel combustion

To facilitate the large-scale utilization of high-alkali and -alkaline earth metals (AAEMs) coals in power generation, the ash deposition behaviors of a typical Zhundong coal in oxy-fuel combustion were experimentally investigated using a drop tube furnace. A wall-temperature-controlled ash deposition probe by which the bulk gas temperature could be measured simultaneously was designed and employed in the experiments. The deposition tendencies, ash morphologies, chemical compositions of deposited ash particles were studied respectively under various oxygen concentrations, bulk gas temperatures, probe surface temperatures and probe exposure times. The experimental results revealed that the oxygen concentration had a significant influence on the deposition behavior during oxy-fuel combustion of high-alkali coal. Compared with air case, more fine ash particles were generated during the combustion of Zhundong coal in 21% O₂/79% CO₂ atmosphere but the deposition tendency was weaker. However, a higher oxygen concentration could aggravate the tendency of ash deposition. The high contents of iron (Fe), calcium (Ca), sulfur (S), and sodium (Na) in Zhundong coal could result in the generations of low-melting point compounds. Calcium in flue gas existed as CaO and was captured prior to SO₃ by the probe surface during the ash deposition process. At the initial 30 min of the ash deposition process, the dark spherical fine ash particles rich in Fe, Na, oxygen (O), and S were largely produced, while in the range of 60–90 min the light spherical fine ash particles with high contents of Ca, barium (Ba), O, and S were generated on the other hand. The deposition mechanisms at different stages were different and the melted CaO (BaO)/CaSO₄ (BaSO₄) would give rise to a fast growth rate of ash deposit.     

Biogas reforming for hydrogen-rich syngas production over a Ni–K/Al2O3 catalyst using a temperature-controlled plasma reactor

Plasma-enhanced catalytic biogas reforming for hydrogen-rich syngas production over a Ni–K/Al₂O₃ catalyst was investigated using a tabular dielectric barrier discharge non-thermal plasma reactor. To better understand the plasma catalysis synergy at elevated temperatures, we compared different reaction modes: plasma catalysis, plasma alone, and catalysis alone in a reaction temperature range of 160–400 °C. The combination of Ni–K/Al₂O₃ and plasma produced synergistic effects. Notably, the plasma-catalytic synergy was temperature-dependent and varied at different reaction temperatures. Using plasma catalysis, the maximum conversion of CH₄ and CO₂ (31.6% and 22.8%, respectively) was attained over Ni–K/Al₂O₃ at 160 °C, while increasing the reaction temperature to 340 °C noticeably enhanced the H₂/CO ratio to 2.71. Moreover, compared to plasma-catalytic biogas reforming at 160 °C, increasing the reaction temperature to 400 °C suppressed biogas conversion with dramatically reduced coke formation on the Ni–K/Al₂O₃ surface from 6.81 wt% to 3.37 wt%.     

Effect of oxy-fuel combustion with steam addition on coal ignition and burnout in an entrained flow reactor

The ignition temperature and burnout of a semi-anthracite and a high-volatile bituminous coal were studied under oxy-fuel combustion conditions in an entrained flow reactor (EFR). The results obtained under oxy-fuel atmospheres (21%O₂-79%CO₂, 30%O₂-70% O₂ and 35%O₂-65%CO₂) were compared with those attained in air. The replacement of CO₂ by 5, 10 and 20% of steam in the oxy-fuel combustion atmospheres was also evaluated in order to study the wet recirculation of flue gas. For the 21%O₂-79%CO₂ atmosphere, the results indicated that the ignition temperature was higher and the coal burnout was lower than in air. However, when the O₂ concentration was increased to 30 and 35% in the oxy-fuel combustion atmosphere, the ignition temperature was lower and coal burnout was improved in comparison with air conditions. On the other hand, an increase in ignition temperature and a worsening of the coal burnout was observed when steam was added to the oxy-fuel combustion atmospheres though no relevant differences between the different steam concentrations were detected.