CO2 Capture for Fossil Fuel‐Fired Power Plants

An overview of technologies for fossil fuel‐fired power plants with drastically reduced CO₂ emissions is given. Post‐combustion capture, pre‐combustion capture, and oxyfuel technology are introduced and compared. Current research results indicate that post‐combustion capture may lead to slightly higher losses in power plant efficiency than the two other technologies. However, retrofitting of existing plants with oxyfuel technology is complex and costly, and retrofitting of pre‐combustion capture is not possible. On the other hand, post‐combustion capture can be retrofitted to existing power plants with only minimal effort. Based on the mature technology of reactive absorption, it can be implemented on a large scale in the near future. Therefore, post‐combustion capture using reactive absorption is discussed here in some detail.     

An overview on oxyfuel coal combustion—State of the art research and technology development

Oxyfuel combustion is seen as one of the major options for CO₂ capture for future clean coal technologies. The paper provides an overview on research activities and technology development through a fundamental research underpinning the Australia/Japan Oxyfuel Feasibility Project. Studies on oxyfuel combustion on a pilot-scale furnace and a laboratory scale drop tube furnace are presented and compared with computational fluid dynamics (CFD) predictions. The research has made several contributions to current knowledge, including; comprehensive assessment on oxyfuel combustion in a pilot-scale oxyfuel furnace, modifying the design criterion for an oxy retrofit by matching heat transfer, a new 4-grey gas model which accurately predicts emissivity of the gases in oxy-fired furnaces has been developed for furnace modelling, the first measurements of coal reactivity comparisons in air and oxyfuel at laboratory and pilot-scale; and predictions of observed delays in flame ignition in oxy-firing.     

Simulation of Post‐Combustion CO2 Capture,a Comparison among Absorption,Adsorption and Membranes

Post‐combustion CO₂ capture was studied in the favorable context where the captured CO₂ can be reused in a neighboring industrial process. Three technologies for CO₂ capture, absorption by amines, adsorption on activated carbon, and separation using polymer membranes, were considered, modeled and compared. The three capture processes were designed for achieving the same performances. The models were integrated in a commercial flowsheeting software. The results show that, for a targeted CO₂ purity of 95 %, the membrane process appears to be the least energy consuming. A next step will be to quantify the environmental benefits using life cycle assessment.     

Post-combustion CO2 capture with chemical absorption: A state-of-the-art review

Global concentration of CO₂ in the atmosphere is increasing rapidly. CO₂ emissions have an impact on global climate change. Effective CO₂ emission abatement strategies such as Carbon Capture and Storage (CCS) are required to combat this trend. There are three major approaches for CCS: post-combustion capture, pre-combustion capture and oxyfuel process. Post-combustion capture offers some advantages as existing combustion technologies can still be used without radical changes on them. This makes post-combustion capture easier to implement as a retrofit option (to existing power plants) compared to the other two approaches. Therefore, post-combustion capture is probably the first technology that will be deployed. This paper aims to provide a state-of-the-art assessment of the research work carried out so far in post-combustion capture with chemical absorption. The technology will be introduced first, followed by required preparation of flue gas from power plants to use this technology. The important research programmes worldwide and the experimental studies based on pilot plants will be reviewed. This is followed by an overview of various studies based on modelling and simulation. Then the focus is turned to review development of different solvents and process intensification. Based on these, we try to predict challenges and potential new developments from different aspects such as new solvents, pilot plants, process heat integration (to improve efficiency), modelling and simulation, process intensification and government policy impact.     

Partial O2-fired coal power plant with post-combustion CO2 capture: A retrofitting option for CO2 capture ready plants

In the work presented in this paper, an alternative process concept that can be applied as retrofitting option in coal-fired power plants for CO₂ capture is examined. The proposed concept is based on the combination of two fundamental CO₂ capture technologies, the partial oxyfuel mode in the furnace and the post-combustion solvent scrubbing. A 330 MW_el Greek lignite-fired power plant and a typical 600 MW_el hard coal plant have been examined for the process simulations. In a retrofit application of the ECO-Scrub technology, the existing power plant modifications are dominated by techno-economic restrictions regarding the boiler and the steam turbine islands. Heat integration from processes (air separation, CO₂ compression and purification and the flue gas treatment) can result in reduced energy and efficiency penalties. In the context of this work, heat integration options are illustrated and main results from thermodynamic simulations dealing with the most important features of the power plant with CO₂ capture are presented for both reference and retrofit case, providing a comparative view on the power plant net efficiency and energy consumptions for CO₂ capture. The operational characteristics as well as the main figures and diagrams of the plant’s heat balances are included.     

Syngas combustion in a 500 Wth Chemical-Looping Combustion system using an impregnated Cu-based oxygen carrier

Chemical-Looping Combustion (CLC) is an emerging technology for CO₂ capture because separation of this gas from the other flue gas components is inherent to the process and thus no energy is expended for the separation. For its use with coal as fuel in power plants, a process integrated by coal gasification and CLC would have important advantages for CO₂ capture. This paper presents the combustion results obtained with a Cu-based oxygen carrier in a continuous operation CLC plant (500 Wth) using syngas as fuel. For comparison purposes pure H₂ and CO were also used. Tests were performed at two temperatures (1073 and 1153 K), different solid circulation rates and power inputs. Full syngas combustion was reached at 1073 K working at f higher than 1.5. The syngas composition had small effect on the combustion efficiency. This result seems to indicate that the water gas shift reaction acts as an intermediate step in the global combustion reaction of the syngas. The results obtained after 40 h of operation showed that the copper-based oxygen carrier prepared by impregnation could be used in a CLC plant for syngas combustion without operational problems such as carbon deposition, attrition, or agglomeration.     

Recent progress of amine modified sorbents for capturing CO2 from flue gas

Under the Paris agreement, China has committed to reducing CO₂ emissions by 60%–65% per unit of GDP by 2030. Since CO₂ emissions from coal-fired power plants currently account for over 30% of the total carbon emissions in China, it will be necessary to mitigate at least some of these emissions to achieve this goal. Studies by the International Energy Agency (IEA) indicate CCS technology has the potential to contribute 14% of global emission reductions, followed by 40% of higher energy efficiency and 35% of renewable energy, which is considered as the most promising technology to significantly reduce carbon emissions for current coal-fired power plants. Moreover, the announcement of a Chinese national carbon trading market in late 2017 signals an opportunity for the commercial deployment of CO₂ capture technologies.Currently, the only commercially demonstrated technology for post-combustion CO₂ capture technology from power plants is solvent-based absorption. While commercially viable, the costs of deploying this technology are high. This has motivated efforts to develop more affordable alternatives, including advanced solvents, membranes, and sorbent capture systems. Of these approaches, advanced solvents have received the most attention in terms of research and demonstration. In contrast, sorbent capture technology has less attention, despite its potential for much lower energy consumption due to the absence of water in the sorbent. This paper reviews recent progress in the development of sorbent materials modified by amine functionalities with an emphasis on material characterization methods and the effects of operating conditions on performance. The main problems and challenges that need to be overcome to improve the competitiveness of sorbent-based capture technologies are discussed.     

Economic implications of oxyfuel application in a lignite-fired power plant

Scope of the work presented in this paper is to examine and evaluate the application of the oxyfuel combustion CO₂ capture technology in a lignite-fired power plant from an economic point of view. Results from simulations dealing with the most important features for CO₂ reduction are performed. The operational characteristics, the efficiency penalties as well as the net efficiency reduction emerging from the Greenfield application of the oxyfuel technology are presented.CO₂ capture costs and the energy requirements associated with the oxyfuel method affect significantly the cost of electricity. This paper focuses on the analysis of the techno-economic factors that result in the increase of the cost of electricity in comparison with the conventional air-fired power plant. For this reason a typical Greek lignite power plant is used as a reference case. Any technical, economic and financial assumptions applied provide a common basis for both power plants (i.e., conventional and oxyfuel) for the assessment of the change of the cost of electricity and the CO₂ capture cost. The oxyfuel simulations are performed by taking into account the adoption of measures for the exploitation of heat that would otherwise be wasted. Such measures concern both the water/steam cycle and the gas flows (e.g., the oxygen flow). Heat integration from processes - such as the air separation, the CO₂ compression and purification and the flue gas treatment - is adopted in order to lower as much as possible the efficiency penalty.The cycle calculations have been performed using the thermodynamic cycle calculation software ENBIPRO (ENergie-BIllanz-PROgram). ENBIPRO is a powerful tool for heat and mass balance solving of complex thermodynamic circuits, calculation of efficiency, exergetic and exergoeconomic analysis of power plants. The software code models all pieces of equipment that usually appear in power plant installations and can accurately calculate all thermodynamic properties (temperature, pressure, enthalpy) at each node of the thermodynamic circuit, power consumption of each component, flue gas composition, etc. The code has proven its validity by accurately simulating a large number of power plants and through comparison of the results with other commercial software (Stamatelopoulos GN. Calculation and optimisation of power plant thermodynamic cycles. VDI-Regulations. Series 6, No. 340. Braunchweig, Mechanical Engineering Department; 1996 [in German]).     

Enhancement of Ca‐Based Sorbent Multicyclic Behavior in Ca Looping Process for CO2 Separation

The Ca‐based sorbent looping cycle represents an innovative way of CO₂ capture for power plants. However, the CO₂ capture capacity of the Ca‐based sorbent decays sharply with calcination/carbonation cycle number increasing. In order to improve the CO₂ capture capacity of the sorbent in the Ca looping cycle, limestone was modified with acetic acid solution. The cyclic carbonation behaviors of the modified and original limestones were investigated in a twin fixed‐bed reactor system. The modified limestone possesses better cyclic carbonation kinetics than the original limestone at each cycle. The modified limestone carbonated at 640–660 °C achieves the optimum carbonation conversion. The acetic acid modification improves the long‐term performance of limestone, resulting in directly measured conversion as high as 0.4 after 100 cycles, while the original limestone remains at a conversion of less than 0.1 at the same reaction conditions. Both the pore volume and pore area distributions of the calcines derived from the modified limestone are better than those derived from the original limestone. The CO₂ partial pressure for carbonation has greater effect on conversion of the original limestone than on that of the modified sorbent because of the difference in their pore structure characteristics. The carbonation conversion of the original limestone decreases with the increase in particle size, while the change in particle size of the modified sorbent has no clear effect on cyclic carbonation behavior.     

Modeling of solid fuels combustion in oxygen-enriched atmosphere in circulating fluidized bed boiler: Part 1. The mathematical model of fuel combustion in oxygen-enriched CFB environment

The paper is focused on the idea of large-scale CFB boiler operation with oxygen/CO₂-modified atmosphere inside combustion chamber. The following main advantages can be found for this technology: reduction of pollutant emissions, possibility of high efficiency separation of CO₂ from the exhaust gases that results from increased CO₂ concentration, lower chimney loss due to the reduction of flue gases in a volume, limitation of the combustion chamber dimensions etc. The paper presents a model of coal combustion in oxygen-enriched CFB environment, where air staging, desulfurization process, NO_x formation and reduction as well as a stationary dense phase of coarse particles in the bottom part of combustion chamber and a circulating dilute phase in the upper part are included.     

Dynamic modelling of CO2 absorption for post combustion capture in coal-fired power plants

Power generation from fossil fuel-fired power plants is the largest single source of CO₂ emissions. Post combustion capture via chemical absorption is viewed as the most mature CO₂ capture technique. This paper presents a study of the post combustion CO₂ capture with monoethanolamine (MEA) based on dynamic modelling of the process. The aims of the project were to compare two different approaches (the equilibrium-based approach versus the rate-based approach) in modelling the absorber dynamically and to understand the dynamic behaviour of the absorber during part load operation and with disturbances from the stripper. A powerful modelling and simulation tool gPROMS was chosen to implement the proposed work. The study indicates that the rate-based model gives a better prediction of the chemical absorption process than the equilibrium-based model. The dynamic simulation of the absorber indicates normal absorber column operation could be maintained during part load operation by maintaining the ratio of the flow rates of the lean solvent and flue gas to the absorber. Disturbances in the CO₂ loading of the lean solvent to the absorber significantly affect absorber performance. Further work will extend the dynamic modelling to the stripper for whole plant analysis.     

三种气体分离技术应用于电厂烟气二氧化碳捕集经济性的比较(英文)

Three gas separation technologies,chemical absorption,membrane separation and pressure swing adsorption,are usually applied for CO2 capture from flue gas in coal-fired power plants.In this work,the costs of the three technologies are analyzed and compared.The cost for chemical absorption is mainly from $30 to $60 per ton(based on CO2 avoided),while the minimum value is $10 per ton(based on CO2 avoided).As for membrane separation and pressure swing adsorption,the costs are $50 to $78 and $40 to $63 per ton(based on CO2 avoided),respectively.Measures are proposed to reduce the cost of the three technologies.For CO2 capture and storage process,the CO2 recovery and purity should be greater than 90%.Based on the cost,recovery,and purity,it seems that chemical absorption is currently the most cost-effective technology for CO2 capture from flue gas from power plants.However,membrane gas separation is the most promising alternative approach in the future,provided that membrane performance is further improved.     

Impact of liquid absorption process development on the costs of post-combustion capture in Australian coal-fired power stations

Australian power generators produce approximately 170 TWh per annum of electricity using black and brown coals that accounts for 170 Mtonne of CO₂ emissions per annum or over 40% of anthropogenic CO₂ emissions in Australia. This paper describes the results of a techno-economic evaluation of liquid absorption based post-combustion capture (PCC) processes for both existing and new pulverised coal-fired power stations in Australia. The overall process designs incorporate both the case with continuous capture and the case with the flexibility to switch a CO₂ capture plant on or off depending upon the demand and market price for electricity, and addresses the impact of the presently limited emission controls on the process cost. The techno-economic evaluation includes both air and water cooled power and CO₂ capture plants, resulting in cost of power generation for the situations without and with PCC. Whilst existing power plants in Australia are all water cooled sub-critical designs, the new power plants are deemed to range from supercritical single reheat to ultra-supercritical double reheat designs, with a preference for air-cooling. The process evaluation also includes a detailed sensitivity analysis of the thermodynamic properties of liquid absorbent for CO₂ on the overall costs. The results show that for a meaningful decrease in the efficiency and cost penalties associated with the post combustion CO₂ capture, a novel liquid sorbent will need to have heat of absorption/desorption, sensible heat and heat of vaporisation around 50% less in comparison with 30% (w/w) aqueous MEA solvent. It also shows that the impact of the capital costs of PCC processes is quite large on the added cost of generation. The results can be used to prioritise PCC research in an Australian context.     

Planning of carbon capture and storage with pinch analysis techniques

Carbon capture and storage (CCS) is a means for reducing carbon dioxide (CO₂) emissions from fossil fuel combustion in power generation and industrial processes. It involves the capture of CO₂ for subsequent storage in various geological formations. The selection and matching of the power plants and storage sites are often an issue of optimisation due to various constraints, i.e., time of availability, injection rate, and storage capacity limits. In this work, a novel graphical targeting tool based on pinch analysis is proposed to address the planning problem of the storage of captured CO₂ from power generating plants into corresponding reservoirs. The main consideration for the problem is the time of availability of the latter, since reservoirs need to be developed prior to CO₂ storage. The time limitation is addressed by the graphical technique where time is taken as the governing element in solving the problem. Hypothetical examples are used to elucidate the proposed approach.     

Carbon capture from stationary power generation sources: A review of the current status of the technologies

The world will need greatly increased energy supply in the future for sustained economic growth, but the related CO₂ emissions and the resulting climate changes are becoming major concerns. CO₂ is one of the most important greenhouse gases that is said to be responsible for approximately 60% of the global warming. Along with improvement of energy efficiency and increased use of renewable energy sources, carbon capture and sequestration (CCS) is expected to play a major role in curbing the greenhouse gas emissions on a global scale. This article reviews the various options and technologies for CO₂ capture, specifically for stationary power generation sources. Many options exist for carbon dioxide capture from such sources, which vary with power plant types, and include post-combustion capture, pre-combustion capture, oxy fuel combustion capture, and chemical looping combustion capture. Various carbon dioxide separation technologies can be utilized with these options, such as chemical absorption, physical absorption, adsorption, and membrane separation. Most of these capture technologies are still at early stages of development. Recent progress and remaining challenges for the various CO₂ capture options and technologies are reviewed in terms of capacity, selectivity, stability, energy requirements, etc. Hybrid and modified systems hold huge future potentials, but significant progress is required in materials synthesis and stability, and implementations of these systems on demonstration plants are needed. Improvements and progress made through applications of process systems engineering concepts and tools are highlighted and current gaps in the knowledge are also mentioned. Finally, some recommendations are made for future research directions.     

Combined Decarbonization of Electrical Energy Generation and Production of Synthetic Fuels by Renewable Energies and Fossil Fuels

Power generation from renewable energy sources and fossil fuels are integrated into one system. A combination of technologies in the form of a carbon capture utilization (CCU)-combined power station is proposed. The technology is based on energy generation from fossil fuels by a coal power plant with CO₂ recovery from exhaust gases, and pyrolysis of natural gas to hydrogen and carbon, completed by reverse water-gas shift for the conversion of CO₂ to CO, which will react with hydrogen in a Fischer-Tropsch synthesis for synthetic diesel. The carbon from the pyrolysis can replace other fossil carbon or can be sequestered. This technology offers significant CO₂ savings compared to the current state of technology and makes an environmentally friendly use of fossil fuels for electricity and fuel sectors possible.     

Comparative assessment of coal fired IGCC systems with CO2 capture using physical absorption,membrane reactors and chemical looping

The integrated gasification combined cycle (IGCC) as an efficient power generation technology with lowest specific carbon dioxide emissions among coal power plants is a very good candidate for CO₂ capture resulting in low energy penalties and minimised CO₂ avoidance costs. In this paper, the techno-economic characteristics of four different capture technologies, which are built upon a conventional reference case, are studied using the chemical process simulation package “ECLIPSE”. The technology options considered are: physical absorption, water gas shift reactor membranes and two chemical looping combustion cycles (CLC), which employ single and double stage reactors. The latter system was devised to achieve a more balanced distribution of temperatures across the reactors and to counteract hot spots which lead to the agglomeration and the sintering of oxygen carriers. Despite the lowest efficiency loss among the studied systems, the economic performance of the double stage CLC was outperformed by systems employing physical absorption and water gas shift reactor membranes. Slightly higher efficiencies and lower costs were associated with systems with integrated air separation units. The estimation of the overall capital costs was carried out using a bottom-up approach. Finally, the CO₂ avoidance costs of individual technologies were calculated based on the techno-economic data.     

燃烧尾气后处理的反应溶剂型大型工业CO2吸收塔工艺技术进展

介绍了工业化经济型CO₂吸收塔的实体案例,总结近十年来工业化CO₂吸收塔的化工装置以及工程技术进展。系统介绍了CO₂吸收塔的化工工艺装置在运行中经常遇到的技术问题以及相应的解决方案,并分析近十年来几类技术发展,分别是溶液降解和降解产物处理技术、气体排放尾气的采样和分析技术、吸收剂主体组分分析技术、降低总体能耗的催化吸收-解吸技术。通过分析可知,利用固体矿物和生物催化剂是降低能耗的有效方法,但存在大量技术问题有待完善和解决。总之,这一系列的化工工艺技术的发展和进步,会为完善经济型吸收塔提供更多可信的实际数据。因此,燃烧尾气后处理的溶剂型CO₂吸收化工工艺装置必然朝着更小的反应器(吸收塔)和更低的能耗发展目标前进,从而实现该装置的高效率和低成本运行。     

Crisp and fuzzy integer programming models for optimal carbon sequestration retrofit in the power sector

Carbon capture and storage (CCS) is one of the interim technologies to mitigate greenhouse gas emissions from stationary sources such as power plant and large industrial facilities. CCS allows for continued utilization of fossil fuels (e.g. coal, natural gas and oil), which are still relatively inexpensive and reliable in comparison to inherently low-carbon renewable resources (e.g. wind, solar etc.). On the other hand, retrofitting power plants for carbon capture (CC) entails major capital costs as well as reduction of thermal efficiency and power output. This paper presents integer programming optimization models for planning the retrofit of power plants at the regional, sectoral or national level. In addition to the base case (i.e., non-fuzzy or crisp) formulation, two fuzzy extensions are given to account for the inherent conflict between environmental and economic goals, as well as parametric uncertainties pertaining to the emerging CC technologies. Case studies are shown to illustrate the modeling approach.     

Modelling of CO2, CO, SO2, O2 and NOx emissions from the oxy-fuel combustion in a circulating fluidized bed

The paper presents a model of coal combustion in air and oxygen-enriched CFB environment. A computer program to calculate the CO₂, CO, SO₂, NO_x and O₂ emissions from the combustion of solid fuels in a circulating fluidized bed boiler was created. The validity of this program was verified by measurements on a 0.1MW_th OxyFuel-CFB Test Rig.The calculations have been carried out for air and so-called oxy-fuel conditions, i.e. when combustion runs in a gas mixture based on O₂ and N₂, with various fractions of oxygen.The comparison between measured and predicted by model CO, SO₂, NO_x and O₂ emissions is shown in this paper. The results of the calculation showed, that the kinetic equations of some reaction have to be modified. Authors propose to use the reaction surface area instead of the specific internal surface area of char in rate constant formulas as the combustion nature changes from internal-kinetic to external-diffusion controlling regime.