Dehydration process and structural development of cordierite ceramic precursors derived from FTIR spectroscopic investigations

 Cordierite precursors were prepared by a sol-gel process using tetraethoxysilane, aluminum sec.-butoxide, and Mg metal flakes as starting materials. The precursors were treated by 15-h heating steps in intervals of 100 °C from 200 to 900 °C; they show a continuous decrease in the analytical water content with increasing preheating temperatures. The presence of H₂O and (Si,Al)–OH combination modes in the FTIR powder spectra prove the presence of both H₂O molecules and OH groups as structural components, with invariable OH concentrations up to preheating temperatures of 500 °C. The deconvolution of the absorptions in the (H₂O,OH)-stretching vibrational region into four bands centred at 3584, 3415, 3216 and 3047 cm⁻¹ reveals non-bridging and bridging H₂O molecules and OH groups. The precursor powders remain X-ray amorphous up to preheating temperatures of 800 °C. Above this temperature the precursors crystallize to μ-cordierite; at 1000 °C the structure transforms to α-cordierite. Close similarities exist in the pattern of the 1400–400 cm⁻¹ lattice vibrational region for precursors preheated up to 600 °C. Striking differences are evident at preheating temperatures of 800 °C, where the spectrum of the precursor powder corresponds to that of conventional cordierite glass. Bands centred in the “as-prepared” precursor at 1137 and 1020 cm⁻¹ are assigned to Si–O-stretching vibrations. A weak absorption at 872 cm⁻¹ is assigned to stretching modes of AlO₄ tetrahedral units and the same assignment holds for a band at 783 cm⁻¹ which appears in precursors preheated at 600 °C. With increasing temperatures, these bands show a significant shift to higher wavenumbers and the Al–O stretching modes display a strong increase in their intensities. (Si,Al)–O–(Si,Al)-bending modes occur at 710 cm⁻¹ and the band at 572 cm⁻¹ is assigned to stretching vibrations of AlO₆ octahedral units. A strong band around 440 cm⁻¹ is essentially attributed to Mg–O-stretching vibrations. The strongly increasing intensity of the 872 and 783 cm⁻¹ bands demonstrates a clear preference of Al for a fourfold-coordinated structural position in the precursors preheated at high temperatures. The observed band shift is a strong indication for increasing tetrahedral network condensation along with changes in the Si–O and Al–O distances to tetrahedra dimensions similar to those occurring in crystalline cordierite. These structural changes are correlated to the dehydration process starting essentially above 500 °C, clearly demonstrating the inhibiting role of H₂O molecules and especially of OH groups. Received: 1 March 2002 / Accepted: 26 June 2002     

High-pressure Raman spectroscopic study of Fo90 hydrous wadsleyite

Raman spectra of monoclinic Fo₉₀ hydrous wadsleyite with 2.4 wt% H₂O have been measured in a diamond-anvil cell with helium as a pressure-transmitting medium to 58.4 GPa at room temperature. The most intense, characteristic wadsleyite modes, the Si–O–Si symmetric stretch at 721 cm⁻¹ and the symmetric stretch of the SiO₃ unit at 918 cm⁻¹, shift continuously to 58.4 GPa showing no evidence of a first order change in the crystal structure despite compression well beyond the stability field of wadsleyite in terms of pressure. The pressure dependence of these two modes is nearly identical for Fo₉₀ hydrous and Fo₁₀₀ anhydrous wadsleyite. A striking feature in the high-pressure Raman spectra of Fo₉₀ hydrous wadsleyite is the appearance of new Raman modes above 9 GPa in the mid-frequency range (300–650 cm⁻¹ at 1-bar and shifted to 500–850 cm⁻¹ at 58.4 GPa) accompanied by a significant growth in their intensities under further compression. In the OH stretching frequency range Fo₉₀ hydrous wadsleyite exhibits a larger number of modes than the Mg end-member phase. The higher number of modes may be due to either additional protonation sites or simply that we observe a different subset of all possible OH modes for each sample. The high-pressure behaviour of the OH stretching modes of Fo₉₀ and Fo₁₀₀ hydrous wadsleyite is consistent: OH stretching modes with frequencies <3,530 cm⁻¹ decrease with increasing pressure whereas the higher-frequency OH modes show a close to constant pressure dependence to at least 13.2 GPa. The approximately constant pressure dependence of the OH modes above 3,530 cm⁻¹ is consistent with protons being located at the O1···O edges around M3.     

Synthesis of Ca-tourmaline in the system CaO-MgO-Al2O3-SiO2-B2O3-H2O-HCl

Summary. ?Ca-tourmaline has been synthesized hydrothermally in the presence of Ca(OH)₂ and CaCl₂-bearing solutions of different concentration at T = 300–700 °C at a constant fluid pressure of 200 MPa in the system CaO-MgO-Al₂O₃-SiO₂-B₂O₃-H₂O-HCl. Synthesis of tourmaline was possible at 400 °C, but only above 500 °C considerable amounts of tourmaline formed. Electron microprobe analysis and X-ray powder data indicate that the synthetic tourmalines are essentially solid solutions between oxy-uvite, CaMg₃- Al₆(Si₆O₁₈)(BO₃)₃(OH)₃O, and oxy-Mg-foitite, □(MgAl₂)Al₆(Si₆O₁₈)(BO₃)₃(OH)₃O. The amount of Ca ranges from 0.36 to 0.88 Ca pfu and increases with synthesis temperature as well as with bulk Ca-concentration in the starting mixture. No hydroxy-uvite, CaMg₃(MgAl₅)(Si₆O₁₈)(BO₃)₃(OH)₃(OH), could be synthesized. All tourmalines have < 3 Mg and > 6 Al pfu. The Al/(Al + Mg)-ratio decreases from 0.80 to 0.70 with increasing Ca content. Al is coupled with Mg and Ca via the substitutions Al₂□Mg₋₂Ca₋₁ and AlMg₋₁H₋₁. No single phase tourmaline could be synthesized. Anorthite ( + quartz in most runs) has been found coexisting with tourmaline. Other phases are chlorite, tremolite, enstatite or cordierite. Between solid and fluid, Ca is strongly fractionated into tourmaline ( + anorthite). The concentration ratio D = Ca(fluid)/Ca(tur) increases from 0.20 at 500 °C up to 0.31 at 700 °C. For the assemblage turmaline + anorthite + quartz + chlorite or tremolite or cordierite, the relationship between Ca content in tourmaline and in fluid with temperature can be described by the equation (whereby T = temperature in °C, Ca(tur) = amount of Ca on the X-site in tourmaline, Ca( fluid) = concentration of Ca²⁺ in the fluid in mol/l). The investigations may serve as a first guideline to evaluate the possibility to use tourmaline as an indicator for the fluid composition.

---

Zusammenfassung. ?Synthese von Ca-Turmelin im System CaO-MgO-Al ₂ O ₃ -SiO ₂ -B ₂ O ₃ -H ₂ O-HCl Im System CaO-MgO-Al₂O₃-SiO₂-B₂O₃-H₂O-HCl wurde Ca-Turmalin hydrothermal aus Ca(OH)₂ and CaCl₂-haltigen L?sungen bei T = 300–700 °C und einem konstanten Fluiddruck von 200 MPa synthetisiert. Die Synthese von Turmalin war m?glich ab 400 °C, aber nur oberhalb von 500 °C bildeten sich deutliche Mengen an Turmalin. Elektronenstrahl-Mikrosondenanalysen und R?ntgenpulveraufnahmen zeigen, da? Mischkristalle der Reihe Oxy-Uvit, CaMg₃Al₆(Si₆O₁₈)(BO₃)₃(OH)₃O, und Oxy-Mg-Foitit, □(MgAl₂)Al₆(Si₆O₁₈)(BO₃)₃(OH)₃O gebildet wurden. Der Anteil an Ca variiert zwischen 0.36 und 0.88 Ca pfu und nimmt mit zunehmender Synthesetemperatur und zunehmender Ca-Konzentration im System zu. Hydroxy-Uvit, CaMg₃(MgAl₅) (Si₆O₁₈)(BO₃)₃(OH)₃(OH), konnte nicht synthetisiert werden. Alle Turmaline haben < 3 Mg und > 6 Al pfu. Dabei nimmt das Al/(Al + Mg)- Verh?ltnis mit zunehmendem Ca-Gehalt von 0.80 auf 0.70 ab. Al ist gekoppelt mit Mg und Ca über die Substitutionen Al₂□Mg₋₂Ca₋₁ und AlMg₋₁H₋₁. Einphasiger Turmalin konnte nicht synthetisiert werden. Anorthit (+ Quarz in den meisten F?llen) koexistiert mit Turmalin. Andere Phasen sind Chlorit, Tremolit, Enstatit oder Cordierit. Ca zeigt eine deutliche Fraktionierung in den Festk?rpern Turmalin (+ Anorthit). Das Konzentrationsverh?ltnis D = Ca(fluid)/Ca(tur) nimmt von 0.20 bei 500 °C auf 0.31 bei 700 °C zu. Für die Paragenese Turmalin + Anorthit + Quarz mit Chlorit oder Tremolit oder Cordierit gilt folgende Beziehung zwischen Ca-Gehalt in Turmalin und Fluid und der Temperatur: (wobei T = Temperatur in °C, Ca(tur) = Anteil an Ca auf der X-Position in Turmalin, Ca(fluid) = Konzentration von Ca²⁺ im Fluid in mol/l). Die Untersuchungen dienen zur ersten Absch?tzung, ob Turmalin als Fluidindikator petrologisch nutzbar ist.

---

---

Received July 24, 1998;/revised version accepted October 21, 1999     

Chemical composition and species attribution of tourmalines from a rare-metal pegmatite vein with scapolite, Sangilen Upland, Tuva

A detailed study of the chemical composition and substitutions in calcium tourmalines from a scapolite-bearing rare-metal pegmatite vein from the Sol’bel’der River basin has shown that their species attribution is determined by occupancy of octahedral site Y. The composition of the yellow tourmaline most abundant in the central part of the pegmatite bodyis rather constant and characterized by the ideal formula Ca(Mg₂Li)Al₆(Si₆O₁₈)(BO₃)₃(OH)₃F. Variations in the chemical composition of zonal tourmaline crystals from the contact part of the pegmatite are controlled by abrupt change in the chemical medium during their formation. The yellow cores of these crystals are close in composition to tourmaline from the central part of the pegmatite vein. The Mg content abruptly decreases toward the crystal margin: Mg²⁺ → Fe²⁺, 2Mg²⁺ → Li⁺ + Al³⁺, and Mg²⁺ + OH → Al³⁺ + O²⁻. The composition of dark green marginal zones in tourmaline is characterized by the ideal formula Ca(Al_1.5Li_1.5)Al₆(Si₆O₁₈)(BO₃)₃ (OH₂O)(F). The results indicate specific formation conditions of pegmatite. The crystallochemical formulas of the studied tourmalines allow us to regard them as new mineral species in the tourmaline group.     

High-pressure and high-temperature Raman spectroscopic study of hydrous wadsleyite (β-Mg2SiO4)

In situ Raman spectra of hydrous wadsleyite (β-Mg₂SiO₄) with ~1.5 wt% H₂O, synthesized at 18 GPa and 1,400°C, have been measured in an externally heated diamond anvil cell up to 15.5 GPa and 673 K. With increasing pressure (at room temperature), the three most intense bands at ~549, 720 and 917 cm⁻¹ shift continuously to higher frequencies, while with increasing temperature at 14.5 GPa, these bands generally shift to lower frequencies. The temperature-induced frequency shifts at 14.5 GPa are significantly different from those at ambient pressure. Moreover, two new bands at ~714 and ~550 cm⁻¹ become progressively significant above 333 and 553 K, respectively, and disappear upon cooling to room temperature. No corresponding Raman modes of these two new bands were reported for wadsleyite at ambient conditions, and they are thus probably related to thermally activated processes (vibration modes) at high-pressure and temperature conditions.     

High-T phase transition of synthetic ANaB(LiMg)CMg5Si8O22(OH)2 amphibole: an X-ray synchrotron powder diffraction and FTIR spectroscopic study

The synthetic amphibole Na_0.95(Li_0.95Mg_1.05)Mg₅Si₈O₂₂(OH)₂ was studied in situ at high-T, using IR OH-stretching spectroscopy and synchrotron X-ray powder diffraction. At room-T the sample has P2₁ /m symmetry, as shown by the FTIR spectrum. It shows in the OH region two well-defined and intense absorptions at 3,748 and 3,712 cm⁻¹, respectively, and two minor bands at 3,667 and 3,687 cm⁻¹. The main bands are assigned to the two independent O–H groups in the primitive structure. The two minor bands evidencing the presence of small amount of vacant A-site (^A□_0.05). With increasing T, these bands shift continuously and merge into a unique absorption at high temperature. A change as a function of increasing T is revealed by the evolution of the refined unit-cell parameters, whose trend shows a transition to C2/m at about 320–330°C. The spontaneous scalar strain, fitted with a tricritical 2–6 Landau potential, gives a T _c of 325(10)°C (β parameter = 0.27). Comparison with the second-order P2₁ /m ⇔ C2/m phase transition at 255°C for synthetic amphibole ^ANa_0.8^B(Na_0.8Mg_1.2)^CMg₅Si₈O₂₂(OH)₂ indicates that the substitution of Na with Li at the B-sites strongly affects the thermodynamic character and the T _c of the phase transition. The comparison of LNMSH amphiboles with cummingtonitic ones shows that the high-T thermodynamic behaviour is affected by A-site occupancy.     

Stability range and decomposition of potassic richterite and phlogopite end members at 5–15 GPa

Summary The phase relations of K-richterite, KNaCaMg₅Si₈O₂₂(OH)₂, and phlogopite, K₃Mg₆ Al₂Si₆O₂₀(OH)₂, have been investigated at pressures of 5–15 GPa and temperatures of 1000–1500 °C. K-richterite is stable to about 1450 °C at 9–10 GPa, where the dp/dT-slope of the decomposition curve changes from positive to negative. At 1000 °C the alkali-rich, low-Al amphibole is stable to more than 14 GPa. Phlogopite has a more limited stability range with a maximum thermal stability limit of 1350 °C at 4–5 GPa and a pressure stability limit of 9–10 GPa at 1000 °C. The high-pressure decomposition reactions for both of the phases produce relatively small amounts of highly alkaline water-dominated fluids, in combination with mineral assemblages that are relatively close to the decomposing hydrous phase in bulk composition. In contrast, the incongruent melting of K-richterite and phlogopite in the 1–3 GPa range involves a larger proportion of hydrous silicate melts. The K-richterite breakdown produces high-Ca pyroxene and orthoenstatite or clinoenstatite at all pressures above 4 GPa. At higher pressures additional phases are: wadeite-structured K₂Si^VISi^IV ₃O₉ at 10 GPa and 1500 °C, wadeite-structured K₂Si^VISi^IV ₃O₉ and phase X at 15 GPa and 1500 °C, and stishovite at 15 GPa and 1100 °C. The solid breakdown phases of phlogopite are dominated by pyrope and forsterite. At 9–10 GPa and 1100–1400 °C phase X is an additional phase, partly accompanied by clinoenstatite close to the decomposition curve. Phase X has variable composition. In the KCMSH-system (K₂CaMg₅Si₈O₂₂(OH)₂) investigated by Inoue et al. (1998) and in the KMASH-system investigated in this report the compositions are approximately K₄Mg₈Si₈O₂₅(OH)₂ and K_3.7Mg_7.4Al_0.6Si_8.0O₂₅(OH)₂, respectively. Observations from natural compositions and from the phlogopite-diopside system indicate that phlogopite-clinopyroxene assemblages are stable along common geothermal gradients (including subduction zones) to 8–9 GPa and are replaced by K-richterite at higher pressures. The stability relations of the pure end member phases of K-richterite and phlogopite are consistent with these observations, suggesting that K-richterite may be stable into the mantle transition zone, at least along colder slab geotherms. The breakdown of moderate proportions of K-richterite in peridotite in the upper part of the transition zone may be accompanied by the formation of the potassic and hydrous phase X. Additional hydrogen released by this breakdown may dissolve in wadsleyite. Therefore, very small amounts of hydrous fluids may be released during such a decomposition. Received April 10, 2000; revised version accepted November 6, 2000     

Location and quantitative analysis of OH in coesite

 The incorporation of hydrogen (deuterium) into the coesite structure was investigated at pressures from 3.1 to 7.5 GPa and temperatures of 700, 800, and 1100 °C. Hydrogen could only be incorporated into the coesite structure at pressures greater 5.0 GPa and 1100 °C . No correlation between the concentration of trace elements such as Al and B and the hydrogen content was observed based on ion probe analysis (1335 ± 16 H ppm and 17 ± 1 Al ppm at 7.5 GPa, 1100 °C). The FTIR spectra show three relatively intense bands at 3575, 3516, and 3459 cm⁻¹ (ν₁ to ν₃, respectively) and two very weak bands at 3296 and 3210 cm⁻¹ (ν₄ and ν₅, respectively). The band at 3516 cm⁻¹ is strongly asymmetric and can be resolved into two bands, 3528 (ν_2a) and 3508 (ν_2b) cm⁻¹, with nearly identical areas. Polarized infrared absorption spectra of coesite single-crystal slabs, cut parallel to (0 1 0) and (1 0 0), were collected to locate the OH dipoles in the structure and to calibrate the IR spectroscopy for quantitative analysis of OH in coesite (ɛ _{i ,tot}=190 000 ± 30 000 l mol⁻¹ _H2O cm⁻²). The polarized spectra revealed a strong pleochroism of the OH bands. High-pressure FTIR spectra at pressures up to 8 GPa were performed in a diamond-anvil cell to gain further insight into incorporation mechanism of OH in coesite. The peak positions of the ν₁, ν₂, and ν₃ bands decrease linearly with pressure. The mode Grüneisen parameters for ν₁, ν₂, and ν₃ are −0.074, −0.144 and −0.398, respectively. There is a linear increase of the pressure derivatives with band position which follows the trend proposed by Hofmeister et al. (1999). The full widths at half maximum (FWHM) of the ν₁, ν₂, and ν₃ bands increase from 35, 21, and 28 cm⁻¹ in the spectra at ambient conditions to 71, 68, and 105 in the 8 GPa spectra, respectively. On the basis of these results, a model for the incorporation of hydrogen in coesite was developed: the OH defects are introduced into the structure by the substitution Si^4+(Si2)+4O²⁻= ^[4]□^(Si2) + 4OH⁻, which gives rise to four vibrations, ν₁, ν_2a, ν_2b, and ν₃. Because the OH(D)-bearing samples do contain traces of Al and B, the bands ν₄ and ν₅ may be coupled to Al and/or B substitution. Received: 19 December 2000 / Accepted: 23 April 2001     

OH in natural orthopyroxene: an in situ FTIR investigation at varying temperatures

In situ unpolarized and polarized Fourier transform infrared spectra of a natural orthopyroxene at varying temperatures were obtained using a heating stage attached on an Infrared microscope. The three main bands (3,595, 3,520 and 3,410 cm⁻¹) at room temperature are ascribed to OH fundamental stretching bands. With increasing temperature from room temperature to 500 °C, the 3,595 cm⁻¹ band shifts 20 cm⁻¹ to lower frequency. The total integral absorbance decreases with increasing temperature. These changes are reversible. Excluding the influences of dehydration, proton migration, thermal expansion, and changes in OH dipole direction, the change of integral absorbance with temperature reflects the temperature dependence of absorption coefficient due to the anharmonicity of OH vibration. Based on the integral absorption coefficient at room temperature (14.84 ppm⁻¹ cm⁻²) from Bell et al. (Am Mineral 80:463–474, 1995), the integral absorption coefficients at other temperatures are calculated. The variation of integral absorption coefficient between room temperature and 500 °C obtained in this study is about 18.5 % and may be greater at higher temperature according to the proposed linear relationship.     

Compositional limits and analogs of monoclinic triple-chain silicates

Growing recognition of triple-chain silicates in nature has prompted experimental research into the conditions under which they can form and the extent of solid solution that is feasible for some key chemical substitutions. Experiments were done primarily in the range of 0.1–0.5 GPa and 200–850 °C for durations of 18–1,034 h. A wide range of bulk compositions were explored in this study that can be classified broadly into two groups: those that are Na free and involve various possible chemical substitutions into jimthompsonite (Mg₁₀Si₁₂O₃₂(OH)₄), and those that are Na bearing and involve chemical substitutions into the ideal end-member Na₄Mg₈Si₁₂O₃₂(OH)₄. Numerous attempts to synthesize jimthompsonite or clinojimthompsonite were unsuccessful despite the type of starting material used (reagent oxides, magnesite + SiO₂, talc + enstatite, or anthophyllite). Similarly, the chemical substitutions of F⁻ for OH⁻, Mn²⁺, Ca²⁺, or Fe²⁺ for Mg²⁺, and 2Li⁺ for Mg²⁺ and a vacancy were unsuccessful at nucleating triple-chain silicates. Conversely, nearly pure yields of monoclinic triple-chain silicate could be made at temperatures of 440–630 °C and 0.2 GPa from the composition Na₄Mg₈Si₁₂O₃₂(OH)₄, as found in previous studies, though its composition is most likely depleted in Na as evidenced by electron microprobe and FTIR analysis. Pure yields of triple-chain silicate were also obtained for the F-analog composition Na₄Mg₈Si₁₂O₃₂F₄ at 550–750 °C and 0.2–0.5 GPa if a flux consisting of Na-halide salt and water in a 2:1 ratio by weight was used. In addition, limited chemical substitution could be documented for the substitutions of 2 Na⁺ for Na⁺ + H⁺ and of Mg²⁺ + vacancy for 2Na⁺. For the former, the Na content appears to be limited to 2.5 cations giving the ideal composition of Na_2.5Mg₈Si₁₂O_30.5(OH)_5.5, while for the latter substitution the Na content may go as low as 1.1 cations giving the composition Na_1.1Mg_9.4Si₁₂O_31.9(OH)_4.1 based on a fixed number of Si cations. Further investigation involving Mg for Na cation exchange may provide a pathway for the synthesis of Na-free clinojimthompsonite. Fairly extensive solid solution was also observed for triple-chain silicates made along the compositional join Na₄Mg₈Si₁₂O₃₂(OH)₄–Ca₂Mg₈Si₁₂O₃₂(OH)₄ where the limit of Ca substitution at 450 °C and 0.2 GPa corresponds to Na_0.7Ca_1.8Mg_7.8Si₁₂O_31.9(OH)_4.1 (with the OH content adjusted to achieve charge balance). Aside from the Na content, this composition is similar to that observed as wide-chain lamellae in host actinolite. The relative ease with which Na-rich triple chains can be made experimentally suggests that these phases might exist in nature; this study provides additional insights into the range of compositions and formation conditions at which they might occur.     

Raman spectra of hydrous γ -Mg2SiO4 at various pressures and temperatures

 One well-defined OH Raman band at 3651 ± 1 cm⁻¹ and one weak feature near 3700 ± 5 cm⁻¹ are recognized for the hydrous γ-phase of Mg₂SiO₄. Like the hydrous β-phase, the H₂O content in the γ-phase shifts most of the corresponding silicate modes towards lower frequencies. Variations in Raman spectra of the hydrous γ-phase were investigated up to about 200 kbar at room temperature and in the range 81–873 K at atmospheric pressure. Unlike the anhydrous γ-phase, which remains intact up to at least 873 K, the hydrous γ-phase sometimes converts to a defective forsterite structure above 800 K. Although the hydrous γ-phase remains intact up to at least 800 K, Raman signals of the OH bands disappear completely above 423 K. The Raman frequency of the well-defined OH band decreases linearly with increasing temperature between 81 and 423 K. In the region of the silicate vibrations, the Raman frequencies of the two most intense bands increase nonlinearly with increasing pressure, and decrease with increasing temperature. The frequencies for all other weak bands, however, decreased linearly with increasing temperature. The latter most likely reflects the larger scatter of the data for the weak bands. Received: 27 April 2001 / Accepted: 12 September 2001     

The orientation and vibrational states of H2O in synthetic alkali-free beryl

 The polarized single-crystal Raman spectra of synthetic H₂O-containing alkali-free beryl were recorded at room and low temperatures, and the polarized single-crystal IR spectra at room temperature. The H₂O molecule in the channel cavities is characterized by a Raman-active symmetric stretching vibration (ν₁) at 3607 cm⁻¹ and an IR-active asymmetric stretch (ν₃) at 3700 cm⁻¹ at room temperature. At low temperatures this ν₃ mode is observed in the Raman. Weak ν₁ and ν₃ modes of a second type of H₂O are also observed in the Raman spectra but only at 5 K. The H⋯&middot;H vector of the most abundant type of H₂O is parallel to the channel axis of beryl along [0 0 0 1]. The components of the polarizability tensor of the ν₁ mode of H₂O are similar to, but not exactly the same as, those of a free H₂O molecule. The Raman measurements indicate that the H₂O molecule is rotationally disordered around [0 0 0 1]. External translation and librational modes of H₂O could be observed as overtones with the internal H₂O-stretching modes. In the case of the librational motions, normal modes could also be observed directly in the Raman spectra at ∼200 cm⁻¹. The energies of the translational modes can be determined from an analysis of the overtones and are about 9 cm⁻¹ in energy (i.e., T_z). The energies of the librational modes are about 210 cm⁻¹ for R_x and 190 cm⁻¹ for R_y. Received: 8 April 1999 / Accepted: 5 April 2000     

Single-crystal EPR and DFT studies of a [BO<Subscript>4</Subscript>]<Superscript>0</Superscript> center in datolite: electronic structure,formation mechanism and implications

A natural datolite CaBSiO₄(OH) (Bergen Hill, NJ, USA), before and after gamma-ray irradiation (up to ~70 kGy), has been investigated by single-crystal and powder electron paramagnetic resonance (EPR) spectroscopy from 10 to 295 K. EPR spectra of gamma-ray-irradiated datolite show the presence of a boron-associated oxygen hole center (BOHC) and an atomic hydrogen center (H⁰), both of which grow with increasing radiation dose. The principal g and A(¹¹B) values of the BOHC at 10 K are: g ₁ = 2.04817(3), g ₂ = 2.01179(2), g ₃ = 2.00310(2), A ₁ = −0.401(7) mT, A ₂ = −0.906(2) mT, A ₃ = −0.985(2) mT, with the orientations of the g ₁ and A ₁ axes approximately along the B–OH bond direction. These experimental results suggest that the BOHC represents hole trapping on the hydroxyl oxygen atom after the removal of the proton (i.e. a [BO₄]⁰ center): via a reaction O₃BOH → O₃BO^· + H⁰, where · denotes the unpaired electron. Density functional theory (DFT) calculations (CRYSTAL06, B3PW, all-electron basis sets, and 1 × 2 × 2 supercell) support the proposed structural model and yield the following ¹¹B hyperfine coupling constants: A ₁ = −0.429 mT, A ₂ = −0.901 mT, A ₃ = −0.954 mT, in excellent agreement with the experimental results. The [BO₄]⁰ center undergoes the onset of thermal decay at ~200°C and is completely annealed out at 375°C but can be restored readily by gamma-ray irradiation. Isothermal annealing experiments show that the [BO₄]⁰ center exhibits a second-order thermal decay with an activation energy of 0.96 eV. The confirmation of the [BO₄]⁰ center (and its formation from the O₃BOH precursor) in datolite has implications for not only understanding of BOHCs in alkali borosilicate glasses but also their applications to nuclear waste disposal.     

Structural thermal behavior of paragonite and its dehydroxylate: a high-temperature single-crystal study

 The lattice constants of paragonite-2M₁, NaAl₂(AlSi₃)O₁₀(OH)₂, were determined to 800 °C by the single-crystal diffraction method. Mean thermal expansion coefficients, in the range 25–600 °C, were: α_a = 1.51(8) × 10⁻⁵, α_b = 1.94(6) × 10⁻⁵, α_c = 2.15(7) ×  10⁻⁵ °C⁻¹, and α_V = 5.9(2) × 10⁻⁵ °C⁻¹. At T higher than 600 °C, cell parameters showed a change in expansion rate due to a dehydroxylation process. The structural refinements of natural paragonite, carried out at 25, 210, 450 and 600 °C, before dehydroxylation, showed that the larger thermal expansion along the c parameter was mainly due to interlayer thickness dilatation. In the 25–600 °C range, Si,Al tetrahedra remained quite unchanged, whereas the other polyhedra expanded linearly with expansion rate proportional to their volume. The polyhedron around the interlayer cation Na became more regular with temperature. Tetrahedral rotation angle α changed from 16.2 to 12.9°. The structure of the new phase, nominally NaAl₂ (AlSi₃)O₁₁, obtained as a consequence of dehydroxylation, had a cell volume 4.2% larger than that of paragonite. It was refined at room temperature and its expansion coefficients determined in the range 25–800 °C. The most significant structural difference from paragonite was the presence of Al in fivefold coordination, according to a distorted trigonal bipyramid. Results confirm the structural effects of the dehydration mechanism of micas and dioctahedral 2:1 layer silicates. By combining thermal expansion and compressibility data, the following approximate equation of state in the PTV space was obtained for paragonite: V/V ₀ = 1 + 5.9(2) × 10⁻⁵ T(°C) − 0.00153(4) P(kbar). Received: 12 July 1999 / Revised, accepted: 7 December 1999     

Low-temperature single-crystal Raman spectrum of pyrope

 The single-crystal polarized Raman spectra of synthetic pyrope, Mg₃Al₂Si₃O₁₂, were measured at room temperature and 5 K, as were the room-temperature unpolarized spectra of two natural pyrope-rich crystals. No major differences in the spectra between room temperature and 5 K are observed or are present between the synthetic and the natural crystals. The spectra are consistent with the proposal that the Mg cation is dynamically disordered and not statically distributed over subsites in the large triangular-dodecahedral E-site in pyrope. A low-energy band at about 135 cm⁻¹ softens and shows a large decrease in its line width with decreasing temperature. The presence of a weak, broad band at about 280 cm⁻¹ may be due to anharmonic effects, as could the one at 135 cm⁻¹. The latter is assigned to the rattling motion of Mg in pyrope in the plane of the longer Mg-O(4) bonds (Kolesov and Geiger 1998). The successful modeling of the anisotropic motion of the Mg cation in pyrope, which has an anharmonic character, provides a valuable test of the validity of empirical or semi-empirical lattice-dynamic calculations for silicates. Received: 10 May 1999 / Accepted: 10 April 2000     

Experimental study of the system H3BO3–NaF–SiO2-H2O at 350–800 °C and 1–2 kbar by the method of synthetic fluid inclusions

The phase state of fluid in the system H₃BO₃–NaF–SiO₂–H₂O was studied at 350–800 °C and 1–2 kbar by the method of synthetic fluid inclusions. The increase in the solubility of quartz and the high reciprocal solubility of H₃BO₃ and NaF in water fluid at high temperatures are due to the formation of complexes containing B, F, Si, and Na. At 800 °C and 2 kbar, both liquid and gas immiscible phases (viscous silicate-water-salt liquid and three water fluids with different contents of B and F) are dispersed within each other. The Raman spectra of aqueous solutions and viscous liquid show not only a peak of [B(OH)₃]⁰ but also peaks of complexes [B(OH)₄]^–, polyborates [B₄O₅(OH)₄]^2–, [B₃O₃(OH)₄]^–, and [B₅O₆(OH)₄]^–, and/or fluoroborates [B₃F₆O₃]^3–, [BF₂(OH)₂]^–, [BF₃(OH)]^–, and [BF₄]^–. The high viscosity of nonfreezing fluid is due to the polymerization of complexes of polyborates and fluorine-substituted polyborates containing Si and Na. Solutions in fluid inclusions belong to P–Q type complicated by a metastable or stable immiscibility region. Metastable fluid equilibria transform into stable ones owing to the formation of new complexes at 800 ºC and 2 kbar as a result of the interaction of quartz with B-F-containing fluid. At high concentrations of F and B in natural fluids, complexes containing B, F, Si, and alkaline metals and silicate-water-salt dispersed phases might be produced and concentrate many elements, including ore-forming ones. Their transformation into vitreous masses or viscous liquids (gels, jellies) during cooling and the subsequent crystallization of these products at low temperatures (300–400 °C) should lead to the release of fluid enriched in the above elements.     

High temperature stability limit of phase egg, AlSiO3(OH)

The stability relations of phase egg, AlSiO₃(OH), have been investigated at pressures from 7 to 20 GPa, and temperatures from 900 to 1700 °C in a multi-anvil apparatus. At the lower pressures phase egg breaks down according to the univariant reaction, phase egg = stishovite + topaz-OH, which extends from 1100 °C at 11 GPa to 1400 °C at 13 GPa where it terminates at an invariant point involving corundum. At pressures above the invariant point, the stability of phase egg is limited by the breakdown reaction, phase egg = stishovite + corundum + fluid, which extends from the invariant point to 1700 °C at 20 GPa. Stishovite crystallized in the Al₂O₃-SiO₂-H₂O system contains Al₂O₃, and the amount of Al₂O₃ increases with increasing temperature. It is inferred that the Al₂O₃ content is controlled by the charge-balanced substitution of Si⁴⁺ by Al³⁺ and H⁺. Aluminum-bearing stishovite coexisting with an H₂O-rich fluid may contain a certain amount of water. Therefore, phase egg and stishovite in a subducting slab could transport some H₂O into the deep Earth. Received: 14 October 1998 / Accepted: 19 May 1999     

Structure and cation disorder of hydrous ringwoodite, γ-Mg1.89Si0.98H0.30O4

The structure of a single crystal hydrous ringwoodite, Mg_1.89Si_0.98H_0.30O₄ synthesized at conditions of 1300?°C and 20?GPa has been analyzed. Crystallographic data for hydrous ringwoodite obtained are; Cubic with Space group: Fd3m (no. 227). a= 8.0693(5)?Å, V=526.41(9)?ų, Z=8, D_calc= 3.48?g?cm^?3. The results of site occupancy refinement using higher angle reflections showed the existence of a small degree of Mg²⁺-Si⁴⁺ disorder in the structure such as (Mg_1.84Si_0.05□_0.11)(Si_0.93Mg_0.05□_0.02)H_0.30O₄. The IR and Raman spectra were measured and OH vibration spectra were observed. A broad absorption band was observed in the IR spectrum and the maxima were observed at 3160?cm^?1 in the IR and at 3165?cm^?1 and 3685?cm^?1 in relatively sharp Raman spectra, which suggest that locations between O-O pairs around the octahedral 16c and 16d sites are possible sites for hydrogen.     

Phosphorus solubility mechanisms in haplogranitic aluminosilicate glass and melt: effect of temperature and aluminum content

The solubility behavior of phosphorus in glasses and melts in the system Na₂O-Al₂O₃-SiO₂-P₂O₅ has been examined as a function of temperature and Al₂O₃ content with microRaman spectroscopy. The Al₂O₃ was added (2, 4, 5, 6, and 8 mol% Al₂O₃) to melts with 80 mol% SiO₂ and ∼2 mol% P₂O₅. The compositions range from peralkaline, via meta-aluminous to peraluminous. Raman spectra were obtained of both the phosphorus-free and phosphorous-bearing glasses and melts between 25 and 1218 °C. The Raman spectrum of Al-free, P-bearing glass exhibits a characteristic strong band near 940 cm⁻¹ assigned to P=O stretching in orthophosphate complexes together with a weaker band near 1000 cm⁻¹ assigned P₂O₇ complexes. With increasing Al content, the proportion of P₂O₇ initially increases relative to PO₄ and is joined by AlPO₄ complexes which exhibit a characteristic P-O stretch mode slightly above 1100 cm⁻¹. The latter complex appears to dominate in meta-aluminosilicate glass and is the only phosphate complex in peraluminous glasses. When P-bearing peralkaline silicate and aluminosilicate glasses are transformed to supercooled melts, there is a rapid decrease in PO₄/P₂O₇ so that in the molten state, PO₄ units are barely discernible. The P₂O₇/AlPO₄ abundance ratio in peralkaline compositions increases with increasing temperature. This decrease in PO₄/P₂O₇ with increasing temperature results in depolymerization of the silicate melts. Dissolved P₂O₅ in peraluminous glass and melts forms AlPO₄ complexes only. This solution mechanism has no discernible influence on the aluminosilicate melt structure. There is no effect of temperature on this solution mechanism. Received: 7 October 1997 / Accepted: 11 May 1998     

Polarized single crystal absorption spectroscopy of the Pnam-P2 1/a transition of Ilvaite Ca(Fe2+, Fe3+)Fe2+Si2O8(OH) as measured between 300 K and 450 K

The temperature dependence of the absorption spectra of ilvaite, Ca(Fe²⁺,Fe³⁺)Fe²⁺Si₂O₈(OH), shows strongly one dimensional transport behaviour with no singularity at the Pnam-P2₁/a phase transition point near 335 K. Polarized single crystal transmission measurements were carried out between 300 K and 450 K in a frequency range between 600 and 23 000 cm⁻¹. No Drude —absorption at low energies was found at any temperature. A macroscopic, thermodynamic model based on Landau-Ginzburg theory is given which accounts for the observed macroscopic properties of the structural phase transition and its coupling with the Fe²⁺-Fe³⁺ ordering. This ordering scheme is discussed on an atomistic level and compared with the behaviour of magnetite and trans-(CH) _x .