Non-destructive thermal property measurements of an APS TBC on an intact turbine blade

The ability to measure the properties of thermal barrier coatings (TBCs) applied to engine components is challenging due to the complex geometry of parts and the difficulty of preparing samples suitable for conventional techniques. As a result, there is a shortage of information related to the morphology and thermal properties of coatings on engine components. Phase of photothermal emission analysis (PopTea) is a relatively new non-destructive technique that is suitable for measuring the thermal properties of coatings on serviceable engine parts. To demonstrate this capability, measurements are performed on an intact turbine blade coated with air plasma sprayed (APS) 7 wt.% Y₂O₃-stabilized ZrO₂ (7YSZ). The average thermal diffusivity of the coating applied to the blade was ~ 0.5 mm²/s which is typical for thermal diffusivity previously measured on 7YSZ APS coatings made on test coupons with PopTea and laser flash. Furthermore, trends in thermal properties over the blade are studied and compared. It is discovered that variations in thermal properties are the result of differences in coating porosity.     

Novel thermal barrier coatings based on La2(Zr0.7Ce0.3)2O7/8YSZ double-ceramic-layer systems deposited by electron beam physical vapor deposition

Double-ceramic-layer (DCL) thermal barrier coatings (TBCs) of La₂(Zr_0.7Ce_0.3)₂O₇ (LZ7C3) and yttria stabilized zirconia (YSZ) were deposited by electron beam-physical vapor deposition (EB-PVD). The thermal cycling test at 1373 K in an air furnace indicates the DCL coating has a much longer lifetime than the single layer LZ7C3 coating, and even longer than that of the single layer YSZ coating. The superior sintering-resistance of LZ7C3 coating, the similar thermal expansion behaviors of YSZ interlayer with LZ7C3 coating and thermally grown oxide (TGO) layer, and the unique growth modes of columns within DCL coating are all very helpful to the prolongation of thermal cycling life of DCL coating. The failure of DCL coating is mainly a result of the reduction-oxidation of cerium oxide, the crack initiation, propagation and extension, the abnormal oxidation of bond coat, the degradation of t′-phase in YSZ coating and the outward diffusion of Cr alloying element into LZ7C3 coating.     

Effects of Laser Remelting and Oxidation on NiCrAlY/8Y<Subscript>2</Subscript>O<Subscript>3</Subscript>-ZrO<Subscript>2</Subscript> Thermal Barrier Coatings

In this study, three groups of thermal barrier coatings (TBCs) samples were remelted by CO₂ laser with different laser energy densities (1, 5 and 10 J/mm²) to seal the surface of yttria-stabilized zirconia (YSZ) coatings. Microscopic observations showed that the cracks size and the remelted depth in YSZ coatings increased. A ~ 50-μm-thick dense layer was formed on the surface of YSZ coating in samples with 1 J/mm² energy density. Microindentation tests showed that the Vickers hardness of YSZ coatings increases with the increase in laser energy density. After isothermal oxidation at 1200 °C for 200 h, thinner thermally growth oxides were found in laser remelted YSZ samples under energy density of 1 J/mm² (6.32 ± 0.28 μm). Cyclic oxidation results showed that the weight gain per unit area of low energy density laser remelted TBCs was smaller than that of the high energy density laser remelted and as-sprayed TBCs.     

表面陶瓷层厚度对Sm2Zr2O7/8YSZ热障涂层热冲击性能的影响

稀土锆酸盐与8YSZ所组成的双陶瓷层涂层是目前热障涂层领域研究的热点,而陶瓷层厚度对其热冲击性能有着显著影响。采用有限元软件ANSYS研究了表层厚度对Sm2Zr2O7/8YSZ热障涂层淬冲击热应力的影响,并与单一Sm2Zr2O7涂层进行了比较。结果表明,在Sm2Zr2O7/8YSZ涂层的表面处具有最大的径向热冲击应力,最大轴向应力则存在于陶瓷层/金属粘结层界面处,涂层各处剪应力基本相当。涂层表面及两陶瓷层界面处的径向热应力随表层厚度的增加而减小,陶瓷层/粘结层界面处径向应力则随表层厚度增加而增大。每个界面处的轴向应力随表层厚度增加而降低,而剪应力绝对值则随表层厚度增加而增大。与单一Sm2Zr2O7涂层相比,Sm2Zr2O7/8YSZ涂层的热应力明显偏小,说明增加涂层的层数有利益改善涂层的抗热冲击性能。     

Hot corrosion behaviour of plasma sprayed YSZ/Al2O3 dispersed NiCrAlY coatings on Inconel-718 superalloy

Oxide dispersed NiCrAlY bond coatings have been developed for enhancing thermal life cycles of thermal barrier coatings (TBCs). However, the role of dispersed oxides on high temperature corrosion, in particular hot corrosion, has not been sufficiently studied. Therefore, the present study aims to improve the understanding of the effect of YSZ dispersion on the hot corrosion behaviour of NiCrAlY bond coat. For this, NiCrAlY, NiCrAlY + 25 wt.% YSZ, NiCrAlY + 50 wt.% YSZ and NiCrAlY + 75 wt.% YSZ were deposited onto Inconel-718 using the air plasma spraying (APS) process. Hot corrosion studies were conducted at 800 °C on these coatings after covering them with a 1:1 weight ratio of Na₂SO₄ and V₂O₅ salt film. Hot corrosion kinetics were determined by measuring the weight gain of the specimens at regular intervals for a duration of 51 h. X-ray diffraction, scanning electron microscopy and energy dispersive spectroscopy techniques were used to determine the nature of phases formed, examine the surface attack and to carry out microanalysis of the hot corroded coatings respectively. The results show that YSZ dispersion causes enhanced hot corrosion of the NiCrAlY coating. Leaching of yttria leads not only to the formation of the YVO₄ phase but also the destabilization of the YSZ by hot corrosion. For the sake of comparison, the hot corrosion behaviour of a NiCrAlY + 25 wt.% Al₂O₃ coating was also examined. The study shows that the alumina dispersed NiCrAlY bond coat offers better hot corrosion resistance than the YSZ dispersed NiCrAlY bond coat, although it is also inferior compared to the plain NiCrAlY bond coat.     

Hot corrosion behaviour of plasma sprayed YSZ/LaMgAl11O19 composite coatings in molten sulfate–vanadate salt

Hot corrosion studies of thermal barrier coatings (TBCs) with different YSZ/LaMgAl₁₁O₁₉ (LaMA) composite coating top coats were conducted in 50 wt.% Na₂SO₄ + 50 wt.% V₂O₅ molten salt at 950 °C for 60 h. Results indicate that TBCs with composite coating top coats exhibit superior oxidation and hot corrosion resistances to the TBC with the traditional YSZ top coat, especially for which has a LaMA overlay. The presence of LaMA can effectively restrain the destabilization of YSZ at the expense of its own partial degradation. The hot corrosion mechanism of LaMA coating and the composite coatings have been explored.     

Synthesis and characterization of Y3Al5O12 and ZrO2-Y2O3 thermal barrier coatings by combustion spray pyrolysis

Y₃Al₅O₁₂ and ZrO₂-Y₂O₃ (8 mol% YSZ) coatings for potential application as thermal barrier coatings were prepared by combustion spray pyrolysis. Thermal cycling of as deposited coatings on stainless steel and FeCrAlY bond coat substrates was carried out at 1000 °C and 1200 °C to determine the thermal fatigue response. Structural and morphological studies on Y₃Al₅O₁₂ and 8 mol% YSZ coatings before and after thermal cycling have been carried out. It has been noted that the coatings on FeCrAlY substrates remain intact after 50 cycles between room temperature and 1200 °C, whereas the coatings on stainless steel show some minor damage such as peeling off near the periphery after 50 cycles at 1000 °C. Thermal diffusivity values of Y₃Al₅O₁₂ and 8 mol% YSZ films were measured by using photo thermal deflection spectroscopy and the values are lower than those of coatings produced by conventional techniques such as EBPVD and APS.     

Opportunities for TBCs in the ZrO2-YO1.5-TaO2.5 system

An examination of the ZrO₂-YO_1.5-TaO_2.5 system reveals several promising attributes for use in thermal barrier coating applications. The rather unique presence of a stable, non-transformable tetragonal region in this ternary oxide system allows for phase stability to high temperatures (1500 °C). Selected compositions with high levels of yttria and tantala have also shown superior resistance to vanadate corrosion than the commercially utilized 7YSZ. In addition, Y + Ta stabilized zirconia compositions within the non-transformable tetragonal phase field exhibit toughness values comparable or somewhat higher than those of 7YSZ, which bodes well for their durability as TBCs. These promising attributes are discussed in this paper in the context of recent experimental work.     

Thermal cycling failure of new LaMgAl11O19/YSZ double ceramic top coat thermal barrier coating systems

New LaMgAl₁₁O₁₉ (LaMA)/YSZ double ceramic top coat thermal barrier coatings (TBCs) with the potential application in advanced gas-turbines and diesel engines to realize improved efficiency and durability were prepared by plasma spraying, and their thermal cycling failure were investigated. The microstructure evolutions as well as the crystal chemistry characteristics of LaMA coating which seemed to have strong influences on the thermal cycling failure of LaMA and the new double ceramic top coat TBCs based on LaMA/YSZ system were studied. For double ceramic top coat TBC system, interface modification of LaMA/YSZ by preparing thin composite coatings seemed to be more preferred due to the formations of multiple cracks during thermal cycling making the TBC to be more strain tolerant and as well as resulting in an improved thermal cycling property. The effects of the TGO stresses on the failure behavior of the TBCs were discussed through fluorescence piezo-spectroscopy analysis.     

Mechanical properties of solution-precursor plasma-sprayed thermal barrier coatings

The microstructure of thermal barrier coatings (TBCs) of 7 wt.% Y₂O₃ stabilized ZrO₂ (7YSZ) deposited using the solution-precursor plasma spray (SPPS) method has: (i) controlled porosity, (ii) vertical cracks, and (iii) lack of large-scale “splat” boundaries. An unusual feature of such SPPS TBCs is that they are well-adherent in ultra-thick forms (~ 4 mm thickness), where most other types of ultra-thick ceramic coatings fail spontaneously. Here a quantitative explanation is provided as to why as-deposited ultra-thick SPPS TBCs are so well-adherent. The mode II toughness of thin (0.2 mm) SPPS TBCs has been measured using the “barb” shear test, which is found to be 66 J m^− 2. Residual stresses in SPPS TBCs of thickness 0.2, 1.5, and 4.0 mm have been estimated using a microstructure-based object-oriented finite element (OOF) method. These stresses are found to be low, as a result of the strain-tolerant microstructure of the SPPS TBCs. The corresponding strain energy release rates that drive mode II cracks in the three different thickness SPPS TBCs have been found to be less than the mode II toughness.     

High rate deposition of thick CrN and Cr2N coatings using modulated pulse power (MPP) magnetron sputtering

As a variation of high power pulsed magnetron sputtering technique, modulated pulse power (MPP) magnetron sputtering can achieve a high deposition rate while at the same time achieving a high degree of ionization of the sputtered material with low ion energies. These advantages of the MPP technique can be utilized to obtain dense coatings with a small incorporation of the residual stress and defect density for the thick coating growth. In this study, the MPP technique has been utilized to reactively deposit thick Cr₂N and CrN coatings (up to 55 μm) on AISI 440C steel and cemented carbide substrates in a closed field unbalanced magnetron sputtering system. High deposition rates of 15 and 10 μm per hour have been measured for the Cr₂N and CrN coating depositions, respectively, using a 3 kW average target power (16.7 W/cm² average target power density), a 50 mm substrate to target distance and an Ar/N₂ gas flow ratio of 3:1 and 1:1. The CrN coatings showed a denser microstructure than the Cr₂N coatings, whereas the Cr₂N coatings exhibited a smaller grain size and surface roughness than those of the CrN coatings for the same coating thickness. The compressive residual stresses in the CrN and Cr₂N coatings increased as the coating thickness increased to 30 μm and 20 μm, respectively, but for thicker coatings, the stress gradually decreased as the coating thickness increased. The CrN coatings exhibited an increase in the scratch test critical load as the thickness was increased. Both CrN and Cr₂N coatings showed a decrease in the hardness and an increase in the sliding coefficient of friction as the coating thickness increased from 2.5 to 55 μm. However, the wear rate of the CrN coatings decreased significantly as the coating thickness was increased to 10 μm or higher. The 10-55 μm CrN coating exhibited low wear rates in the range of 3.5-5 × 10⁻⁷ mm³ N⁻¹ m⁻¹. To the contrary, the Cr₂N coating exhibited relatively low wear resistance in that high wear rates in the range of 3.5 to 7.5 × 10⁻⁶ mm³ N⁻¹ m⁻¹ were observed for different thicknesses.     

Microstructural analysis of YSZ and YSZ/Al2O3 plasma sprayed thermal barrier coatings after high temperature oxidation

Air plasma sprayed TBCs usually include lamellar structure with high interconnected porosities which transfer oxygen from YSZ layer towards bond coat and cause TGO growth and internal oxidation of bond coat.The growth of thermally grown oxide (TGO) at the interface of bond coat and ceramic layer and internal oxidation of bond coat are considered as the main destructive factors in thermal barrier coatings.Oxidation phenomena of two types of plasma sprayed TBC were evaluated: (a) usual YSZ (yttria stabilized zirconia), (b) layer composite of (YSZ/Al₂O₃) which Al₂O₃ is as a top coat over YSZ coating. Oxidation tests were carried out on these coatings at 1100°C for 22, 42 and 100h. Microstructure studies by SEM demonstrated the growth of TGO underneath usual YSZ coating is higher than for YSZ/Al₂O₃ coating. Also cracking was observed in usual YSZ coating at the YSZ/bond coat interface. In addition severe internal oxidation of the bond coat occurred for usual YSZ coating and micro-XRD analysis revealed the formation of the oxides such as NiCr₂O₄, NiCrO₃ and NiCrO₄ which are accompanied with rapid volume increase, but internal oxidation of the bond coat for YSZ/Al₂O₃ coating was lower and the mentioned oxides were not detected.     

基于磁过滤技术的热障涂层表面Al2O3 覆盖层抗CMAS腐蚀性能

为了提高热障涂层（TBC）的抗沉积物（主要成分为CaO、MgO、Al₂O₃和SiO₂,简称CMAS）腐蚀性能,采用磁过滤阴极真空电弧（FCVA）技术在TBC表面上制备了致密的Al₂O₃覆盖层,比较和分析了Al₂O₃改性TBC和沉积态TBC的润湿行为和抗CMAS腐蚀性能。结果表明：使用FCVA技术制备Al₂O₃覆盖层的过程对7%（质量分数）氧化钇稳定的氧化锆（7YSZ）相的结构无明显影响,且经Al₂O₃改性的TBC综合性能均优于沉积态TBC。在1250 ℃、CMAS腐蚀条件下,Al₂O₃覆盖层有效地限制了熔融CMAS在TBC表面上的扩散行为。同时,Al₂O₃填充了7YSZ柱状晶之间的间隔并且阻碍了熔融CMAS的渗透,证明了FCVA可作为一种制备Al₂O₃涂层的新方法以提高TBC的抗CMAS腐蚀性能,且Al₂O₃涂层及其制备过程对TBC的热震性能均无消极影响。     

Investigation of interfacial properties of atmospheric plasma sprayed thermal barrier coatings with four-point bending and computed tomography technique

A modified four-point bending test has been employed to investigate the interfacial toughness of atmospheric plasma sprayed (APS) yttria stabilised zirconia (YSZ) thermal barrier coatings (TBCs) after isothermal heat treatments at 1150 °C. The delamination of the TBCs occurred mainly within the TBC, several to tens of microns above the interface between the TBC and bond coat. X-ray diffraction analysis revealed that the TBC was mainly tetragonal in structure with a small amount of the monoclinic phase. The calculated energy release rate increased from ~ 50 J/m^− 2 for as-sprayed TBCs to ~ 120 J/m^− 2 for the TBCs exposed at 1150 °C for 200 h with a loading phase angle about 42°. This may be attributed to the sintering of the TBC. X-ray micro-tomography was used to track in 3D the evolution of the TBC microstructure non-destructively at a single location as a function of thermal exposure time. This revealed how various types of imperfections develop near the interface after exposure. The 3D interface was reconstructed and showed no significant change in the interfacial roughness after thermal exposure.     

Novel thermal barrier coatings based on La2Ce2O7/8YSZ double-ceramic-layer systems deposited by electron beam physical vapor deposition

Novel thermal barrier coatings based on La₂Ce₂O₇/8YSZ double-ceramic-layer (DCL) systems, which were deposited by electron beam physical vapor deposition (EB-PVD), were found to have a longer lifetime compared to the single layer La₂Ce₂O₇ (LC) system, and even much longer than that of the single layer 8YSZ system under burner rig test. The DCL coating structure design can effectively alleviate the thermal expansion mismatch between LC coating and bond coat, as well as avoid the chemical reaction between LC and Al₂O₃ in thermally grown oxide (TGO), which occurs above 1000 °C as determined by differential scanning calorimetry (DSC) analysis. The failure mechanism of LC/8YSZ DCL coating is mainly due to the sintering of LC coating surface after long-term thermal cycling.     

Atmospheric plasma sprayed thermal barrier coatings with high segmentation crack densities: Spraying process, microstructure and thermal cycling behavior

Thermal barrier coatings (TBCs) with high strain tolerance are favorable for application in hot gas sections of aircraft turbines. To improve the strain tolerance of atmospheric plasma sprayed (APS) TBCs, 400 μm-500 μm thick coatings with very high segmentation crack densities produced with fused and crushed yttria stabilized zirconia (YSZ) were developed. Using a Triplex II plasma gun and an optimized spraying process, coatings with segmentation crack densities up to 8.9 cracks mm^− 1, and porosity values lower than 6% were obtained. The density of branching cracks was quite low which is inevitable for a good inter-lamellar bonding.Thermal cycling tests yielded promising strain tolerance behavior for the manufactured coatings. Samples with high segmentation crack densities revealed promising lifetime in burner rig tests at rather high surface (1350 °C) and bondcoat temperatures (up to 1085 °C), while coatings with lower crack densities had a reduced performance. Microstructural investigations on cross-sections and fracture surfaces showed that the segmentation crack network was stable during thermal shock testing for different crack densities. The main failure mechanism was delamination and horizontal cracking within the TBC near the thermal grown oxide layer (TGOs) and the TBC.     

The effect of pre-oxidation atmosphere on the durability of EB-PVD thermal barrier coatings with CoNiCrAlY bond coats

The effects of pre-oxidation heat treatment on oxidation behavior and thermal cycle life of electron-beam physical deposited (EB-PVD) thermal barrier coatings (TBCs) with CoNiCrAlY bond coats were investigated as a function of the pO₂ of the pre-oxidation atmosphere. The pO₂ of the pre-oxidation atmosphere was controlled by using a solid-state electrochemical oxygen pump system. The purity and microstructure of the continuous Al₂O₃ layer formed on the bond coat during pre-oxidation at 1050 °C were highly influenced by the pO₂ of the atmosphere. High purity α-Al₂O₃ with large grain size was formed on the bond coats under a pO₂ of 10^− 12-10^− 9 Pa, which resulted in a lower growth rate of TGO and longer lifetime.     

等离子喷涂ZrO2热障涂层热冲击破坏研究

对比研究了等离子喷涂ZrO2梯度热障涂层及传统的双层结构热障涂层,选择NiCoCrAlTaY合金粉末作为热障涂层的粘结底层材料、7％Y2O3-ZrO2作为热障涂层的面层材料、不同比例的NiCoCrAlTaY与7％Y2O3-ZrO2(YPZ)复合粉末作为梯度过渡层材料,然后进行热冲击试验、金相分析及扫描电子显微镜形貌分析,结果表明梯度热障涂层热冲击寿命明显高于传统的双层结构热障涂层。     

Reaction, transformation and delamination of samarium zirconate thermal barrier coatings

The rare earth zirconates have attracted interest for thermal barrier coatings (TBCs) because they have very low intrinsic thermal conductivities, are stable above 1200 °C and are more resistant to sintering than yttria-stabilized zirconia (YSZ). Samarium zirconate (SZO) has the lowest thermal conductivity of the rare earth zirconates and its pyrochore structure is stable to 2200 °C but little is known about its response to thermal cycling. Here, columnar morphology SZO coatings have been deposited on bond coated superalloy substrates using a directed vapor deposition method that facilitated the incorporation of pore volume fractions of 25 to 45%. The as-deposited coatings had a fluorite structure which transformed to the pyrochlore phase upon thermal cycling between 100 and 1100 °C. This cycling eventually led to delamination of the coatings, with failure occurring at the interface between the TGO and a “mixed zone” that formed between the thermally grown alumina oxide (TGO) and the SZO. While the delamination lifetime increased with coating porosity (reduction in coating modulus), it was significantly less than that of similar YSZ coatings applied to the same substrates. The reduced life resulted from a reaction between the rare earth zirconate and the alumina-rich bond coat TGO, leading to the formation of a mixed zone consisting of SZO and SmAlO₃. Thermal strain energy calculations show that the delamination driving force increases with TGO and mixed layer thicknesses and with coating modulus. The placement of a 10 μm thick YSZ layer between the TGO and SZO layers eliminated the mixed zone and restored the thermal cyclic life to that of YSZ structures.     

Plasma spraying of functionally graded yttria stabilized zirconia/NiCoCrAlY coating system using composite powders

Pre-alloyed and plasma spheroidized composite powders were used as the feedstock in the plasma spraying of functionally graded yttria stabilized zirconia (YSZ)/NiCoCrAlY coatings. The ball milling parameters of the composite powders and the plasma spraying parameters for preparing functionally graded materials (FMGs) coatings were optimized to obtain the best performance for the thermal barrier coatings (TBCs). Microstructure, physical, mechanical, and thermal properties of YSZ/NiCoCrAlY FGMs coatings were investigated and compared with those of traditional duplex coatings. Results showed that the advantages of using pre-alloyed composite powders in plasma spraying were to ensure chemical homogeneity and promote uniform density along the graded layers. Microstructure observation showed the gradient distribution of YSZ and NiCoCrAlY phases in the coating, and no clear interface was found between two adjacent different layers. Oxidation occurred during plasma spray and the resultant aluminum oxide combines with YSZ in a wide range of proportions. The bond strength of functionally graded coatings was about twice as high as that of the duplex coatings because of the significant reduction of the residual stresses in the coatings. The thermal cycling resistance of functionally graded coating was much better than that of duplex coating.