Analysis of internal helically finned tubes for parabolic trough design by CFD tools

This paper has analysed the effect of the utilization of internal finned tubes for the design of parabolic trough collectors with computational fluid dynamics tools. Our numerical approach has been qualified with the computational estimation of reported experimental data regarding phenomena involved in finned tube applications and solar irradiation of parabolic trough collector. The application of finned tubes to the design of parabolic trough collectors must take into account features as the pressure losses, thermal losses and thermo-mechanical stress and thermal fatigue. Our analysis shows an improvement potential in parabolic trough solar plants efficiency by the application of internal finned tubes.     

Modelling of parabolic trough direct steam generation solar collectors

Solar electric generation systems (SEGS) currently in operation are based on parabolic trough solar collectors using synthetic oil heat transfer fluid in the collector loop to transfer thermal energy to a Rankine cycle turbine via a heat exchanger. To improve performance and reduce costs direct steam generation in the collector has been proposed. In this paper the efficiency of parabolic trough collectors is determined for operation with synthetic oil (current SEGS plants) and water (future proposal) as the working fluids. The thermal performance of a trough collector using Syltherm 800 oil as the working fluid has been measured at Sandia National Laboratory and is used in this study to develop a model of the thermal losses from the collector. The model is based on absorber wall temperature rather than fluid bulk temperature so it can be used to predict the performance of the collector with any working fluid. The effects of absorber emissivity and internal working fluid convection effects are evaluated. An efficiency equation for trough collectors is developed and used in a simulation model to evaluate the performance of direct steam generation collectors for different radiation conditions and different absorber tube sizes. Phase change in the direct steam generation collector is accounted for by separate analysis of the liquid, boiling and dry steam zones.     

Analytic modeling of a solar power plant with parabolic linear collectors

An analytic model for a solar thermal electric generating system with parabolic trough collectors was developed. The energy conversion of solar radiation into thermal power along the absorber tube of the parabolic collector is studied, taking into consideration the non-linearity of heat losses and its dependence on the local temperature. The coupling between the collector and the thermodynamic cycle is made up of three heat exchangers, yielding the characteristic temperatures of the cycle. The conventional Rankine cycle is treated as an endo-reversible Carnot cycle, whereby the mechanical and electric power is calculated. For comparison, we refer to the Solar Electric Generating System VI (SEGS VI), installed in the Mojave desert-CA, whose solar field is composed by LS2 parabolic trough collectors. We simulated the efficiency curves of collectors LS2 with evacuated and non-evacuated absorbers and compared with experimental results. A second simulation was carried out to estimate the optimum quantity of non-evacuated LS2 collectors in series in a collectors’ row, when friction losses along the absorber tubes are considered. Also, the performance of a 30 (MWe) power plant, composed of 50 rows with 16 LS2 collectors in series (total 800 collectors) was simulated. Three fields of different collectors were considered, the first field with evacuated absorbers, the second with non-evacuated absorbers and the third with bare absorbers. Finally, the output power of the plant is analyzed as a function of the evaporation temperature of the water-vapor fluid. A large maximum of the overall cycle efficiency is found for evaporation temperatures around 320 °C. Good agreement is obtained when comparing the results of this model with experimental data belonging to the Solar Electric Generating Systems (SEGS) installed in the Mojave desert. The analytic model developed combines simplicity, precision and flexibility, making it an attractive tool for simulation and design of solar power stations.     

A conceptual design of solar boiler

State-of-the-art concepts for solar thermal power systems are based on parabolic trough, tower or parabolic disks either heating molten salts, mineral oil, air or generating steam. We propose in this paper, a conceptual design of a solar boiler. This concept comes from the conventional thermal power plants boiler, with the difference that the heat comes from mirrors that concentrate the solar radiation on wall-type array of solar collectors, instead of coming from fuel flames and hot gases. In our preliminary performance, analysis of this innovative solar boiler applied to electricity production, we have found that overall efficiency of the conversion from direct solar irradiation energy to electricity is above 20%, which is comparable to the value of parabolic trough and central tower technologies. Besides that, the concept seems very robust and could overcome some drawbacks derived from pressure losses, control complexity and material thermo-mechanical stress.     

Modeling and optimizing parabolic trough solar collector systems using the least squares support vector machine method

Investigating the complicated thermal physics mechanisms of the parabolic trough solar collector systems plays a vital role in efficiently utilizing the solar energy. In this paper, the least squares support vector machine (LSSVM) method is developed to model and optimize the parabolic trough solar collector system. Numerical simulations are implemented to evaluate the feasibility and efficiency of the LSSVM method, where the sample data derived from the experiment and the simulation results of two solar collector systems with 30 m² and 600 m² solar fields, and the complicated relationship between the solar collector efficiency and the solar flux, the flow rate and the inlet temperature of the heat transfer fluid (HTF) is extracted. Some basic rules, such as the solar collector efficiency increases with the increase of the solar flux and the flow rate of the heat transfer fluid, and decreases with the increase of the inlet temperature of the HTF, are obtained, which indicates the LSSVM method is competent to optimize the solar collector systems. As a result, the new approach will provide meaningful data for developing the parabolic trough solar thermal power plant in China.     

Thermal enhancement of solar parabolic trough collectors by using nanofluids and converging-diverging absorber tube

Parabolic trough collectors are the most mature technology for utilizing the solar energy in high temperature applications. The objective of this study is the thermal efficiency enhancement of the commercial parabolic collector IST-PTC by increasing the convective heat transfer coefficient between the working fluid and the absorber. There are two main factors which influence on this parameter, the working fluid type and the absorber geometry. For this reason three working fluids are investigated, thermal oil, thermal oil with nanoparticles and pressurized water. Moreover, a dimpled absorber tube with sine geometry is tested because this shape increases the heat transfer surface and increases the turbulence in the flow. The final results show that these two techniques improve the heat transfer coefficient and the thermal efficiency of the collector. More specifically, the use of nanofluids increases the collector efficiency by 4.25% while the geometry improvement increases the efficiency by 4.55%. Furthermore, collector parameters such as the heat loss coefficient, the exergetic efficiency, the pressure losses and the absorber temperature are presented for all the examined cases. The model is designed with Solidworks and is simulated by its flow simulation studio.     

Performance evaluation of v-trough solar concentrator for water desalination applications

The working principle and thermal performance of a new v-trough solar concentrator are presented in this paper. Compared with the common parabolic trough solar concentrators, the new concentrator has two parabolic troughs which form a V-shape with the focal line at the bottom of the troughs. This is beneficial for the installation and insulation of the receiver, and the shadow on the reflective surface is avoided. The new v-trough collector does not require high precision tracking devices and reflective material. And therefore the cost of the system could be significantly reduced. Various experimental tests were carried out both outdoor and indoor using different types of receiver tubes. The results show that the collector system can have thermal efficiency up to 38% at 100 °C operating temperature. System modelling was used to predict the rate of fresh water produced by four different solar collector systems which include both static and one-axis solar tracking technologies. Comparison of the solar collectors at different temperature ranges for humidification/dehumidification desalination process using specific air flow rate were considered. At each temperature range, suitable solar collectors were compared in the aspect of fresh water production and area of solar collector required. Results showed that the new v-trough solar collector is the most promising technology for small to medium scale solar powered water desalination.     

槽式太阳能集热器热性能实验测试

针对天津市槽式太阳能集热系统性能测试平台,对不同太阳辐射强度、入口流体温度以及不同工质流量状况下集热效率和集热管压降变化规律进行实验测试,通过测试数据对槽式太阳能集热器热性能进行分析.试验结果表明:在天津地区槽式太阳能集热器集热效率可以达到66.1％;太阳辐射强度的增强,会提高集热效率,并且集热器进出口的压降会随之降低...     

Performance analysis of new-design solar air collectors for drying applications

This paper presents a performance analysis of four types of air heating flat plate solar collectors: a finned collector with an angle of 75°, a finned collector with an angle of 70°, a collector with tubes, and a base collector. In this study, the first and second laws of efficiencies were determined for the collectors and comparisons were made among them. The results showed that the efficiency depends on the solar radiation and the construction of the solar air collectors. The temperature rise varied almost linearly with the incident radiation. The first law of efficiency changed between 26% and 80% for collector-I, between 26% and 42% for collector-II, between 70% and 60% for collector-III, and between 26% and 64% for collector-IV. The values of second law efficiency varied from 0.27 to 0.64 for all collectors? The highest collector efficiency and air temperature rise were achieved by the finned collector with angle of 75°, whereas the lowest values were obtained for the base collector. The effectiveness order of the collectors was determined as the finned collector with angle of 75°, the finned collector with angle of 70°, the collector with tubes, and the base collector.     

Exergetic analysis of a solar thermal power system

This communication presents a second law analysis based on an exergy concept for a solar thermal power system. Basic energy and exergy analysis for the system components (viz. parabolic trough collector/receiver and Rankine heat engine, etc.) are carried out for evaluating the respective losses as well as exergetic efficiency for typical solar thermal power systems under given operating conditions. It is found that the main energy loss takes place at the condenser of the heat engine part, whereas the exergy analysis shows that the collector–receiver assembly is the part where the losses are maximum. The analysis and results can be used for evaluating the component irreversibilities which can also explain the deviation between the actual efficiency and ideal efficiency of a solar thermal power system.     

Heat losses from parabolic trough solar collectors

Parabolic trough solar collector usually consists of a parabolic solar energy concentrator, which reflects solar energy into an absorber. The absorber is a tube, painted with solar radiation absorbing material, located at the focal length of the concentrator, usually covered with a totally or partially vacuumed glass tube to minimize the heat losses. Typically, the concentration ratio ranges from 30 to 80, depending on the radius of the parabolic solar energy concentrator. The working fluid can reach a temperature up to 400°C, depending on the concentration ratio, solar intensity, working fluid flow rate and other parameters. Hence, such collectors are an ideal device for power generation and/or water desalination applications. However, as the length of the collector increases and/or the fluid flow rate decreases, the rate of heat losses increases. The length of the collector may reach a point that heat gain becomes equal to the heat losses; therefore, additional length will be passive. The current work introduces an analysis for the mentioned collector for single and double glass tubes. The main objectives of this work are to understand the thermal performance of the collector and identify the heat losses from the collector. The working fluid, tube and glass temperature's variation along the collector is calculated, and variations of the heat losses along the heated tube are estimated. It should be mentioned that the working fluid may experience a phase change as it flows through the tube. Hence, the heat transfer correlation for each phase is different and depends on the void fraction and flow characteristics. However, as a first approximation, the effect of phase change is neglected. Copyright © 2013 John Wiley & Sons, Ltd.     

Performance of Cylindrical Parabolic Collector with Automated Tracking System

Parabolic solar collector collects the radiant energy emitted from the sun and focuses it at a point. Parabolic trough collectors are the low cost implementation of concentrated solar power technology that focuses incident sun light on to a tube filled with a heat transfer fluid. However, the basic problem with the cylindrical parabolic collector without tracking was the solar collector does not move with the orientation of sun. Development of automatic tracking system for cylindrical parabolic collectors will increase solar collection as well as efficiency of devices. The main aim of this paper is to design, fabricate and analyze the performance of parabolic collector with automated tracking system. The automated tracking mechanism is used to receive the maximum possible energy of solar radiation as it tracks the path of sun. The performance of the parabolic trough collector is experimentally investigated with the water circulated as heat transfer fluid. The collector efficiency will be noted.     

SECOND LAW ANALYSIS OF A SOLAR THERMAL POWER SYSTEM

This communication presents second law analysis based on exergy concept for a solar thermal power system. Basic energy and exergy analysis for the system components (viz. parabolic trough collector/receiver and Rankine heat engine etc.) are carried out for evaluating the energy and exergy losses as well as exergetic efficiency for typical solar thermal power system under given operating conditions. Relevant energy flow and exergy flow diagrams are drawn to show the various thermodynamic and thermal losses. It is found that the main energy loss takes place at the condenser of the heat engine part whereas the exergy analysis shows that the collector-receiver assembly is the part where the losses are maximum. The analysis and results can be used for evaluating the component irreversibilities which can also explain the deviation between the actual efficiency and ideal efficiency of solar thermal power system.     

Control scheme for direct steam generation in parabolic troughs under recirculation operation mode

Electricity production using solar thermal energy is one of the main research areas at present in the field of renewable energies, these systems being characterised by the need of reliable control systems aimed at maintaining desired operating conditions in the face of changes in solar radiation, which is the main source of energy. A new prototype of solar system with parabolic trough collectors was implemented at the Plataforma Solar de Almería (PSA, South-East Spain) to investigate the direct steam generation process under real solar conditions in the parabolic solar collector field of a thermal power plant prototype. This paper presents details and some results of the application of a control scheme designed and tested for the recirculation operation mode, for which the main objective is to obtain steam at constant temperature and pressure at the outlet of the solar field, so that changes produced in the inlet water conditions and/or solar radiation will only affect the amount of steam produced by the solar field. The steam quality and consequently the nominal efficiency of the plant are thus maintained.     

A novel PVT/PTC/ORC solar power system with PV totally immersed in transparent organic fluid

A novel hybrid PVT/parabolic trough concentrator (PTC)/organic Rankine cycle (ORC) solar power system integrated with underground heat exchanger has been proposed. The evaporator unit consists of a transparent flat PVT solar collector and a PTC connected in series. The first transparent solar collector has transparent covers and consists of solar cells totally immersed within a pressurized transparent organic fluid that allows the solar radiation to reach the solar cells, cools them effectively, and captures all thermal losses from the solar cells. The second concentrator is a conventional one with opaque black receiver used to reheat the transparent organic fluid to higher temperatures. Both solar collectors (the PVT and PTC) perform as the boiler and superheater for the ORC. The performance of the proposed system is investigated by a steady‐state mathematical model. The results show that, at design conditions, the efficiency of the PV modules stabilizes around 12%, absorber efficiency varies within 64% to 75%, and the ORC efficiency varies within 7% to 17%.     

Utilizing the multi-objective particle swarm optimization for designing a renewable multiple energy system on the basis of the parabolic trough solar collector

Today, to preserve fossil resources, mankind has to search for new ways to respond to its ever-increasing energy needs. In this study, a hybrid system of energy and the use of a parabolic trough solar collector to attract solar radiation was investigated to produce clean electricity, cooling, and hydrogen from thermodynamic and economic aspects. The designed system consisted of a parabolic trough solar collector, organic Rankine cycle, lithium-bromide absorption refrigeration cycle, and proton exchange membrane electrolysis system. The evaporator input temperature, turbine inlet temperature, solar radiation intensity, mass flow rate of collector and parabolic trough collector surface area were set as decision variables and the effect of these parameters on system performance and system exergy loss were investigated. The objective functions of this research were exergy efficiency and cost rate. In order to optimize this system, multi-objective particle swarm optimization algorithm was employed. Optimization results with particle swarm optimization indicated that the best rate of exergy efficiency is 3.12% and the system cost rate is 16.367 US$ per hour, at the same time. The system is capable of producing 15.385 kW power, 0.189 kg/day hydrogen and 56.145 kW cooling in its optimum condition. The results of sensitivity analysis showed that increasing mass flow rate at the collector, temperature at the evaporator inlet, and temperature at the turbine inlet have positive effect on the performance of the proposed system.     

Eulerian multiphase study of direct steam generation in parabolic trough with OpenFOAM

Direct steam generation (DSG) in parabolic trough solar collectors is a feasible option for economic improvement in solar thermal power generation. Three-dimensional Eulerian two-fluid simulations are performed under OpenFOAM to study the turbulent flow in the evaporation section of the parabolic trough receiver and investigate the phase change, and pressure drop of water as a heat transfer fluid. First, the model's validity has been tested by comparing the numerical results of a laboratory scale boiler with the available correlations and semi-correlations of boiling flows from the literature. Simulations agreed well with Rouhani–Axelsson correlation for horizontal tubes, with a mean relative error of less than 7.1% for all studied cases. However, despite a mean relative error of less than 13.19% compared to the experimental data in the literature, the reported pressure drop factor remains valid; overprediction remains tolerable for most engineering applications. Second, the scaling effect on the mathematical model, from laboratory to commercial-scale configuration, was tested with experimental data of the DISS test loop in Platforma Solar de Almeria, Spain. The Monte Carlo Ray Tracing method under the Tonatiuh package allowed for obtaining the nonuniform heat flux distribution. Due to the large size of the evaporation section in the DISS loop (eight collectors), each collector is considered independently in the simulations. Thus, simulations follow each other, taking the numerical results of each collector output as input data in the next collector and so on until the last. The numerical results showed an excellent agreement for the void fraction with 3.53% against the Rouhani–Axelsson correlation. Frictional pressure losses are within a 17.06% error of the Friedel correlation, in the range of previous work in the literature, and the heat loss is less than 4.69% error versus experimental correlation.     

Design, manufacture and testing of fiberglass reinforced parabola trough for parabolic trough solar collectors

The design and manufacture of a smooth 90° rim angle fiberglass reinforced parabolic trough for parabolic trough solar collector hot water generation system by hand lay up method is described in this paper. The total thickness of the parabolic trough is 7 mm. The concave surface where the reflector is fixed is manufactured to a high degree of surface finish. The fiberglass reinforced parabolic trough was tested under a load corresponding to the force applied by a blowing wind with 34 m/s. Distortion of the parabola due to wind loading was found to be within acceptable limits. The thermal performance of the newly developed fiberglass reinforced parabolic collector was determined according to ASHRAE Standard 93 [ASHRAE Standard 93, 1986. Method of testing to determine the thermal performance of solar collectors. American Society of Heating, Refrigerating and Air-Conditioning Engineers, Atlanta, GA]. The standard deviation of the distribution of the parabolic surface errors is estimated as 0.0066 rad from the collector performance test according to ASHRAE Standard 93 (1986), which indicates the high accuracy of the parabolic surface.     

金属直通型集热管非选择性吸收涂层段热性能研究

考虑金属连接裸管和膨胀节的影响,建立了太阳能槽式集热器能量转换数学模型,分析其吸热、散热和光热转换效率并与常规计算方式进行了对比。计算表明金属连接裸管段的热损失较大,其对集热器性能的影响较膨胀节更为显著。随着太阳直射辐射强度的降低和金属集热管温度的升高,太阳能槽式集热器光热转换效率逐渐降低。对比等同计算方式,本文所采用的差异化计算所得的吸热量较低,集热器热效率与文献中的实测值相比误差在3%左右,更加贴近实际情况。     

CPC Solar Collectors With Flat Bifacial Absorbers

The design, construction and test results of non-evacuated stationary CPC solar collectors with flat absorbers are presented and discussed. The proposed collector design is based on a truncated asymmetric CPC reflector, consisting of a parabolic and a circular part. A flat bifacial absorber is installed at the upper part of the collector, parallel to the glazing to form a thermal trap space between the reverse absorber surface and the circular part of the mirror. Two prototypes based on the same collector geometry were constructed and tested. The first model consists of one mirror–absorber unit and the second of three smaller units integrated in one collector device. The truncated CPC mirror and the installation of the absorber parallel to the glazing keep the optical efficiency at a satisfactory level. The reduction of radiative thermal losses by using selective absorbers and the suppression of convection thermal losses from the reverse absorber surface to the collector cover result to a significant decrease of the total collector thermal losses. The experimental results showed that the proposed CPC collector could achieve a maximum efficiency of 0.71 and a stagnation temperature of about 180°C, with the multiunit collector device being more efficient and practical.