ZrB2增韧Al2O3陶瓷制备工艺及其对复相陶瓷力学性能影响

Al₂O₃陶瓷因具有很高的强度和耐蚀性受到广泛关注。但由于相对较差的韧性限制了其广泛应用。Al₂O₃陶瓷增韧的方式很多,本文采用微米ZrB₂来增韧氧化铝陶瓷,探讨复相陶瓷烧结工艺,并研究工艺参数对复相陶瓷力学性能及韧性的影响。结果表明：采用单因素法得到两种陶瓷最佳工艺参数分别是纯α-Al₂O₃陶瓷烧结温度为1500℃,成型压力为450MPa,保温时间为8h,球料比为1/2,保压时间为10min;ZrB₂(wt,20%)+α-Al₂O₃ (wt,80%)复相陶瓷烧结温度为1450℃,成型压力为450MPa,保温时间为8h,球料比为1/2,保压时间为10min。其中成型压力、烧结温度和保温时间对复相陶瓷硬度及致密度影响最大。ZrB₂的加入,在降低陶瓷烧结温度的同时,可以将纯α-Al₂O₃陶瓷的断裂韧性由5.2±0.3MPa.m^_1/2提高到6.7±0.2MPa.m^_1/2。     

La2O3掺杂AgSnO2电接触材料的制备及性能研究

以Ag、Sn、La₂O₃粉为原料,采用机械合金法制备复合粉体。结合氧化法与粉末冶金工艺,对复合粉体进行氧化、压制、烧结。采用扫描电镜(SEM)和能谱仪、硬度计、金相显微镜、金属电导率测量仪等对复合粉体氧化前后的形貌以及电接触材料烧结前后的性能进行表征。结果表明：烧结后,电接触材料硬度较于烧结前明显下降。同时电接触材料随Sn含量增大,电阻率升高,密度反而下降。在一定的La₂O₃(0wt.%、0.75wt.%、1.5wt.%、2.25wt.%、3wt.%)含量范围内,La₂O₃掺杂量越高,密度越低。同时电接触材料经烧结后,随La₂O₃含量增加,其电阻率先降后升,在La₂O₃含量为0.75wt.%时,电接触材料的电阻率最低。     

La2O3含量对搅拌摩擦加工制备Ni /Al复合材料组织和性能的影响

采用搅拌摩擦加工方法在Al基体中添加不同La₂O₃含量的混合粉末(Ni+La₂O₃),制备 (Ni+La₂O₃)/Al复合材料。采用SEM、EDS、 EPMA及XRD对复合区微观结构及相组成进行分析,采用室温拉伸试验对 (Ni+La₂O₃)/Al复合材料力学性能进行了测试。结果表明,随着La₂O₃含量的增加,(Ni+La₂O₃)/Al复合材料的组织和性能先变好后变差。当La₂O₃添加量达到5%时,复合材料中Al₃Ni增强颗粒分布均匀、颗粒数量最多,块状的Ni粉团聚减少,其抗拉强度达到最大值215MPa,相比Ni/Al复合材料(抗拉强度176MPa),其抗拉强度提高了22%;当La₂O₃的添加量为7%时,复合材料中Al₃Ni增强颗粒含量减少,块状Ni粉团聚重新出现,抗拉强度下降至201MPa。     

三元共晶成分Al2O3/YAG/ZrO2粉体及陶瓷的制备与组织性能研究

本文采用醇水共沉淀法制备了三元共晶成分Al₂O₃/YAG/ZrO₂粉体,在600-1350_oC温度范围煅烧后研究其物相转变过程。经1300_oC煅烧后Al₂O₃/YAG/ZrO₂共晶成分粉体的物相由α-Al₂O₃、c-ZrO₂和YAG构成,且具有α-Al₂O₃相包裹c-ZrO₂相的特殊结构。将煅烧粉体在1550_oC下热压烧结,制备具有内晶型结构的共晶成分Al₂O₃/YAG/ZrO₂复相陶瓷,其致密度、室温抗弯强度、断裂韧性和高温(1000_oC)抗弯强度分别为98.8%、420 MPa、3.69 MPa.m_1/2和464 MPa,并对复相陶瓷组织结构的形成机理进行了探讨。     

SNDC/La2Mo2O9复合电解质材料的制备及性能表征

本文采用甘氨酸-硝酸盐法(GNP)和溶胶凝胶法分别合成了Sm_0.1Nd_0.1Ce_0.8O_1.9(SNDC) 和La₂Mo₂O₉(LAMOX)粉末,并用常压烧结的方法制备了不同比例的SNDC和LAMOX的复合材料,通过XRD和SEM等手段表征了不同复合比例样品的物相和表面形貌并测试了烧结样品的电导率。结果表明,复合样品的电导率在相变点前后随着复合量增加变化趋势相反,其中LAMOX含量为20mol%的样品在550℃时的电导率能达到0.01S/cm,高于同温度下SNDC电导率。     

Al2O3/Ti2AlN复合材料在900℃,1000℃和1100℃空气中的氧化行为

利用综合热分析仪、背散射扫描电镜(BSE)和能谱分析(EDS)对Al₂O₃/Ti₂AlN复合材料在900 ℃,1 000 ℃和1 100 ℃/20 h空气中连续氧化20h后的氧化增重及氧化层截面进行了研究。结果表明：Al₂O₃/Ti₂AlN复合材料在空气中的氧化行为符合抛物线规律,在900 ℃,1 000 ℃和1 100 ℃/20 h氧化增重分别为2.78×10_-2 kg/m₂、10.4 ×10_-2 kg/m₂、21.9 ×10_-2 kg/m₂,抛物线速率常数相应为1.08×10_-8 kg₂/m₄s、1.44×10_-7 kg₂/m₄s、6.56×10_-7 kg₂/m₄s,氧化激活能为274 kJ/mol。氧化层主要由TiO₂和Al₂O₃组成的,连续的Al₂O₃次外层可以提高其抗氧化性能。氧化层结构的改变是由于氧化温度对Ti₄₊、Al₃₊由基体表面向外扩散和O_2-向内扩散的影响,以及TiO₂和Al₂O₃在不同温度下的形核生长速率导致的。对Al₂O₃/Ti₂AlN而言,控制材料与氧化气氛的界面是提高该材料抗氧化性能的关键。     

Mn掺杂提高IrO2-Ta2O5 电极在硫酸溶液中析氧的电催化活性

制备了不同 Mn 含量的IrO₂-Ta₂O₅-MnO_x电极。揭示了Mn含量对该类电极的物理和电化学特性的影响。结果表明,涂??覆的IrO₂-Ta₂O₅-MnO_x层由于其凹凸不平的多孔结构而具有较大的比表面积。少量Mn的加入抑制了活性成分IrO₂的结晶,并将其转化为Ir³⁺。适当地用 Mn 代替Ir可以显著提高 IrO₂-Ta₂O₅-MnO_x 电极的电催化性能。高的电催化活性、长的寿命和低的成本得益于 Mn 掺杂的电极具有更大的活性表面积,从而促进了硫酸溶液中氧的析出。     

Fe2O3-CaO-TiO2 体系下铁酸钙的合成过程及TiO2 和CaTiO3 的影响

为了确定高钛型钒钛磁铁矿烧结过程中铁酸钙的生成是受TiO₂还是TiO₂和CaO形成的CaTiO₃影响,首先利用Fe₂O₃和CaO的纯试剂合成了铁酸钙,并研究了TiO₂和CaTiO₃对钛铁酸钙 （FCT） 形成的影响。在Factsage 7.0软件进行热力学计算的基础上,通过在空气气氛下进行烧结,获得了在1023~1423 K温度范围内、不同烧结时间的不同样品。通过X射线衍射和扫描电镜-能谱分析等表征手段,对烧结样品的物相转变和微观结构变化进行了表征。发现FCT的形成过程主要分为2个阶段：前一阶段为1023~1223 K温度范围内Fe₂O₃与CaO之间的反应,合成产物为Ca₂Fe₂O₅,反应方程式为“Fe₂O₃(s)+ 2CaO(s)= Ca₂Fe₂O₅(s)”;后一阶段为1223~1423 K温度范围内Ca₂Fe₂O₅和Fe₂O₃的反应,主要产物为CaFe₂O₄,反应为“Ca₂Fe₂O₅(s)+ Fe₂O₃(s)= 2CaFe₂O₄(s)”,该阶段尤其是温度为1423 K时,反应速率显著加快,随温度的升高CaTiO₃显著增加。然而,Ti元素在铁酸钙中的固溶很难实现,TiO₂与铁酸钙之间的反应不是形成FCT的有效途径。随着保温时间的延长,CaTiO₃和FCT相界中Fe元素含量增加。FCT主要是通过Fe组分在CaTiO₃中固溶形成的,主要反应是“Fe₂O₃+CaTiO₃(s)=FCT(s)”。     

溶胶凝胶法制备LaMn1-XVXO3及光催化氧化性能

以La(NO₃)₂、MnC₄H₆O₂、柠檬酸和乙二醇(EG)为主要原料,NH₄VO₃为掺杂试剂,采用溶胶凝胶法制备LaMnO₃和LaMn_1-XV_XO₃粉体。采用XRD进行晶体结构表征;采用甲基橙(MO)模拟污水,进行光催化降解实验。研究了煅烧温度、催化剂用量和掺杂量对光催化氧化降解率的影响,讨论MO降解的动力学规律。结果表明700-900 ℃煅烧温度不影响LaMnO₃晶体结构和光催化氧化降解率;掺杂量影响LaMn_1-XV_XO₃晶体结构,光催化氧化降解率随着掺杂量增加而呈下降趋势;光催化氧化实验中,LaMn_1-XV_XO₃粉体效果高于LaMnO₃,两者均符合一级动力学方程。     

BN/Al2O3 复合粉末及其聚合物基复合材料的制备与导热性能

采用固-液相共混法制备了多种BN/Al₂O₃复合粉末,通过冻融法和表面修饰法对BN进行了改性处理,改变表面修饰剂类型和摩尔比得到了前驱体和烧结态BN/Al₂O₃复合粉末,并利用机械混合法制备了聚合物基BN/Al₂O₃复合材料,并测试分析了其导热性能。结果表明,经冻融处理的BN分散性和界面相容性明显优于未经冻融处理的BN。多巴胺对BN的改性效果优于聚乙二醇。采用多巴胺作为表面修饰剂且BN与Al(NO₃)₃的摩尔比为1:1时,能够得到纳米Al₂O₃均匀包覆的微米BN粉末,即BN/Al₂O₃微纳复合粉末,其聚合物基复合材料的导热系数可达0.62 W·m^-1·K^-1,是纯聚合物导热系数的3倍,是采用纯微米BN粉末制备的聚合物基复合材料导热系数的1.5倍。在BN表面附着的Al₂O₃可以形成层状热传导通道,能够有效提高聚合物基BN/Al₂O₃复合材料的热导率。     

Effects of K2O-Li2O doping on surface and catalytic properties of Fe2O3/Cr2O3 system

The effects of K₂O and Li₂O-doping (0.5, 0.75 and 1.5 mol%) of Fe₂O₃/Cr₂O₃ system on its surface and the catalytic properties were investigated. Pure and differently doped solids were calcined in air at 400-600 °C. The formula of the un-doped calcined solid was 0.85Fe₂O₃:0.15Cr₂O₃. The techniques employed were TGA, DTA, XRD, N₂ adsorption at −196 °C and catalytic oxidation of CO oxidation by O₂ at 200-300 °C. The results revealed that DTA curves of pure mixed solids consisted of one endothermic peak and two exothermic peaks. Pure and doped mixed solids calcined at 400 °C are amorphous in nature and turned to α-Fe₂O₃ upon heating at 500 and 600 °C. K₂O and Li₂O doping conducted at 500 or 600 °C modified the degree of crystallinity and crystallite size of all phases present which consisted of a mixture of nanocrystalline α- and γ-Fe₂O₃ together with K₂FeO₄ and LiFe₅O₈ phases. However, the heavily Li₂O-doped sample consisted only of LiFe₅O₈ phase. The specific surface area of the system investigated decreased to an extent proportional to the amount of K₂O and Li₂O added. On the other hand, the catalytic activity was found to increase by increasing the amount of K₂O and Li₂O added. The maximum increase in the catalytic activity, expressed as the reaction rate constant (k) measured at 200 °C, attained 30.8% and 26.5% for K₂O and Li₂O doping, respectively. The doping process did not modify the activation energy of the catalyzed reaction but rather increased the concentration of the active sites without changing their energetic nature.     

国外多孔基体氧化铝/氧化铝复合材料工程应用进展

氧化铝/氧化铝复合材料(Al2O3/Al2O3)是20世纪90年代兴起的一类连续陶瓷纤维增强陶瓷基复合材料,已经发展为与SiC/SiC、C/SiC等非氧化物陶瓷基复合材料并列的一类陶瓷基复合材料。与非氧化物陶瓷基复合材料相比,Al2O3/Al2O3具有长时抗氧化、高温耐腐蚀、低成本等独特优势,已经在航空发动机、地面燃气轮机等军民两用热结构材料领域展现出广阔的应用前景。本文从材料应用的角度出发,系统分析阐述了目前在Al2O3/Al2O3占主导地位的多孔基体Al2O3/Al2O3(P-Al2O3/Al2O3)的增韧机制、成型工艺和性能特点,重点归纳了国外近年来P-Al2O3/Al2O3的工程化应用进展及前景,最后指出了P-Al2O3/Al2O3存在的局限性并展望了未来发展方向,旨在为国内Al2O3/Al2O3体系发展提供借鉴和参考。     

La2O3含量对Al2O3/Cu基复合材料组织与性能的影响

以La₂O₃粉、Al粉、CuO粉为反应物原料、纯铜为基体,采用原位合成技术和近熔点铸造法制备颗粒增强Cu基复合材料,研究La₂O₃对Al-CuO体系制备的Cu基复合材料组织及性能的影响。结果表明：添加La₂O₃可获得纳米Al₂O₃颗粒,且弥散分布于Cu基体中,制备的材料组织更加细小、均匀,其材料的电导率及摩擦磨损性能明显提高。当添加0.6%wtLa₂O₃,复合材料的电导率达到90.2%IACS,磨损量达到最小,相比未添加La₂O₃,其导电率提高10.1%,磨损量减小36.6%。     

Effect of Bi2O3 on structure and wetting studies of Bi2O3-ZnO-B2O3 glasses

Glasses with different Bi₂O₃ contents (37-42 mol%) have been prepared by conventional melt quench technique. The IR and Raman studies indicate that these glasses are made up of [BiO₆], [BiO₃], [BO₃] and [BO₄] basic structural units. The vibrations of [BiO₃] and [BO₃] become stronger as the content of Bi₂O₃ increases, which makes glass structure loosened. Viscosity of the glasses was measured by using a Rheotronic III paralleled plate rheometry, which shows that the viscosity of glass samples decreased when the content of Bi₂O₃ increased at the same temperature (400-460 °C). The temperature range which suits for glasses sealing was calculated by using the approximation of Arrhenian behaviour. The wetting performance of Bi₂O₃-ZnO-B₂O₃ glasses was described by using high-temperature microscope, which also proves that the structure of investigated Bi₂O₃-ZnO-B₂O₃ glasses become loosened due to the increasing of the content of Bi₂O₃.     

Al2O3包覆LiNi0.03Co0.05Mn1.92O4正极材料的制备及其电化学性能

以Al(NO3)3?9H2O为包覆原料,通过燃烧法制备得到LiNi0.03Co0.05Mn1.92O4@Al2O3正极材料。通过X射线衍射(XRD),场发射扫描电子显微镜(FESEM)和透射电镜(TEM)等表征手段对材料的结构和形貌进行分析,并通过恒电流充放电、循环伏安(CV)、交流阻抗(EIS)等测试分析材料的电化学性能。结果表明,Al2O3包覆没有改变LiNi0.03Co0.05Mn1.92O4的尖晶石型结构,包覆层厚度约10.6nm。LiNi0.03Co0.05Mn1.92O4@Al2O3正极材料电化学性能得到了明显改善,1 C和10 C倍率下初始放电比容量分别为119.9 mAh?g-1和106.3 mAh?g-1,充放电循环500次后容量保持率分别为88.4%和78.2%,而未包覆的LiNi0.03Co0.05Mn1.92O4在1 C和10 C倍率下初始放电比容量分别为121.2 mAh?g-1和104.0 mAh?g-1,500次循环后容量保持率分别为84.1%和67.6%。LiNi0.03Co0.05Mn1.92O4@Al2O3活化能为32.92 kJ?mol-1,而未包覆材料的活化能为36.24 kJ?mol-1,包覆有效降低了材料Li+扩散所需克服的能垒,提高了材料的电化学性能。     

纳米级和微米级稀土氧化物掺杂W-La2O3-Y2O3-ZrO2 阴极尖端的组织和性能

使用粉末冶金法将纳米级(70–80 nm)和微米级(500–600 nm)稀土氧化物(La₂O₃,Y₂O₃)与钨粉混合,随后通过冷等静压、中频感应烧结、旋锻、拉拔等一系列工艺制备了W-1.5La₂O₃-0.1Y₂O₃-0.1ZrO₂(质量分数,%)材料。对含有纳米和微米尺寸稀土氧化物的阴极样品使用相同的焊接电流,分别进行了0.5、1、2 h的氩弧焊。结果表明,具有纳米级稀土氧化物的样品在焊接过程中表现出更高的工作稳定性,烧损同比降低了近85.4%。此外,随着工作时间的延长,阴极尖端不同区域的稀土氧化物聚集度显著增加。结合COMSOL Multiphysics温度模拟发现,第二相的扩散活化能降低了近34%。这是因为更为细小的第二相有效地控制了钨基体组织的演变,保留了大量晶界作为通道,促进了活性物质在电子发射过程中的扩散。     

Synthesis and characterization of Y3Al5O12 and ZrO2-Y2O3 thermal barrier coatings by combustion spray pyrolysis

Y₃Al₅O₁₂ and ZrO₂-Y₂O₃ (8 mol% YSZ) coatings for potential application as thermal barrier coatings were prepared by combustion spray pyrolysis. Thermal cycling of as deposited coatings on stainless steel and FeCrAlY bond coat substrates was carried out at 1000 °C and 1200 °C to determine the thermal fatigue response. Structural and morphological studies on Y₃Al₅O₁₂ and 8 mol% YSZ coatings before and after thermal cycling have been carried out. It has been noted that the coatings on FeCrAlY substrates remain intact after 50 cycles between room temperature and 1200 °C, whereas the coatings on stainless steel show some minor damage such as peeling off near the periphery after 50 cycles at 1000 °C. Thermal diffusivity values of Y₃Al₅O₁₂ and 8 mol% YSZ films were measured by using photo thermal deflection spectroscopy and the values are lower than those of coatings produced by conventional techniques such as EBPVD and APS.     

Fe3O4/SiO2/Bi2WO6磁性复合光催化剂的制备及其光催化性能

钨酸铋(Bi₂WO₆),结构最简单的Aurivillius相化合物,是近期受到研究者关注的新型光催化材料。然而,光催化剂粉末在反应介质中难被回收,工业化应用成本较高。本文用三步方法合成了可回收的Fe₃O₄/SiO₂/Bi₂WO₆磁性复合光催化剂,通过溶剂热法合成具有磁性的Fe₃O₄,用溶胶凝胶法在Fe₃O₄表面覆盖SiO₂层,后将磁性颗粒与Bi₂WO₆纳米片相结合。光催化剂的形貌结构及性能通过XRD、SEM、PL、UV-vis进行表征测试。结果表明,直径约500 nm的Fe₃O₄微球附着在边长约500 nm的Bi₂WO₆纳米片的表面,SiO₂在两者之间起到了粘连作用。光催化剂Fe₃O₄/SiO₂/Bi₂WO₆对于罗丹明B的光降解活性较好,且有一定磁性,可以通过外加磁场将其从溶液中分离,有较大的应用潜力。     

Mechanochemical synthesis of Al2O3-TiB2 nanocomposite powder from Al-TiO2-H3BO3 mixture

Alumina-titanium diboride nanocomposite (Al₂O₃-TiB₂) was produced using mixtures of titanium dioxide, acid boric and pure aluminum as raw materials via mechanochemical process. The phase transformation and structural characterization during mechanochemical process were utilized by X-ray diffractometry (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and thermogravimetric analyses (TG-DTA) techniques. A thermodynamic appraisal showed that the reaction between TiO₂, B₂O₃ and Al is highly exothermic and should be self-sustaining. XRD analyses exhibited that the Al₂O₃-TiB₂ nanocomposite was formed after 1.5 h milling time. The results indicate that increasing milling time up to 40 h had no significant effect other than refining the crystallite size.     

In-situ TiB2 and Al2O3 formation by DC plasma spraying

In-situ plasma spraying (IPS) is a promising process to fabricate composite coatings with in-situ formed thermodynamically stable phases. In the present study, mechanically alloyed Al-12Si, B₂O₃ and TiO₂ powder was deposited onto an aluminum substrate using atmospheric plasma spraying (APS). It has been observed that, during the coating process, TiB₂ and Al₂O₃ are in-situ formed through the reaction between starting powders and finely dispersed in hypereutectic Al-Si matrix alloy. Also, obtained results demonstrate that in-situ reaction intensity strongly depends on spray conditions.