常压等离子体改善高性能纤维粘结性的研究

以氦气为载气,氧气为反应气体,对高强度聚乙烯和Twaron 1000芳纶两种高性能纤维进行常压等离子体处理,来改善纤维的粘结性能;采用单纤维抽拔实验测定等离子体处理前后纤维与环氧树脂之间的界面剪切力;利用原子力显微镜和X射线光电子能谱仪分析等离子体处理前后纤维表面形态和化学成分的变化。结果表明:高强度聚乙烯纤维和芳纶经常压等离子体处理后,纤维表面粗糙度增加,纤维表面碳元素含量下降,羟基、羧基等含氧或氮的极性基团增加,纤维粘结性能得到提高,但其强度无明显变化。     

空气等离子体处理芳纶Ⅲ的性能研究

比较了国产芳纶Ⅲ与芳纶1414以及进口Twaron纤维的表面性能;采用空气等离子体处理技术对芳纶Ⅲ的表面进行改性,研究了空气等离子体处理工艺条件以及处理前后芳纶Ⅲ的结构与性能的变化。结果表明:国产芳纶Ⅲ的表面存在不均匀的浅沟槽,比芳纶1414和Twaron纤维表面粗糙,其表面浸润性较差,但却优于芳纶1414和Twaron纤维;空气等离子体处理芳纶Ⅲ的最佳条件为放电功率65 W,空气放电气压2 000 Pa,处理时间11 min,在此条件下处理的芳纶Ⅲ表面接触角由未处理时的55.8°降至41.5°,纤维的浸润性能得到改善,而其力学性能和大分子结构不受影响。     

水分对常压等离子体处理纤维结构与性能的影响

在空气相对湿度为5%,65%和95%的条件下,应用氦气/氧气常压等离子体处理芳纶和超高强度聚乙烯纤维,采用单纤维抽拔实验测定处理前后纤维与环氧树脂间的层间剪切强度,利用原子力显微镜和X射线光电子能谱仪分析等离子体处理前后纤维表面形态和化学成分的变化.结果表明:等离子体处理纤维随着处理环境湿度的增加,水分促进了芳纶表面的...     

空气等离子体处理芳纶纤维及其与天然橡胶/乳聚丁苯橡胶的黏合性能

考察了空气等离子体处理对芳纶纤维表面结构形态的影响,研究了空气等离子体和间苯二酚-甲醛-胶乳(RFL)浸胶处理芳纶纤维与天然橡胶(NR)/乳聚丁苯橡胶(ESBR)的黏合性能,并对经处理的芳纶纤维与NR/ESBR体系的界面层作了动态力学分析。结果表明,芳纶纤维经空气等离子体处理后,表面粗糙度增大,表面积增加,结晶度减小,但处理功率过大、处理时间过长时,芳纶纤维的表面又变得比较光滑、结晶度又呈增大趋势。随着等离子体处理时间的延长,芳纶纤维与NR/ESBR的黏合性能增强,但处理时间过长时,芳纶纤维与NR/ESBR的黏合性能下降;等离子体处理芳纶纤维经RFL进一步浸胶处理后,芳纶纤维与NR/ESBR的黏合性能大幅度提高。芳纶纤维与NR/ESBR的界面存在介于高模量芳纶纤维和低模量橡胶之间的过渡层。     

芳纶纤维等离子体接枝改性处理研究

采用等离子体接枝对芳纶纤维表面进行改性处理,采用XPS、浸润性、界面剪切强度对等离子体接枝处理前后的表面组成、复合材料界面粘接性能等进行了研究,结果表明:等离子体接枝处理可以有效地提高芳纶纤维表面的极性官能团,增加与基体树脂-环氧树脂的浸润性,进而提高芳纶/环氧复合材料的界面粘接强度.     

芳纶纤维的表面处理及其在橡胶工业中的应用

介绍了芳纶纤维的种类、性能、表面改性及其在橡胶制品中的应用。芳纶纤维高模量、高强度、低密度、耐氧化、耐腐蚀的性能使其在轮胎、软管、胶布等橡胶基体复合材料领域作为增强材料有着广泛的应用前景。由于表面的惰性限制了芳纶纤维的应用,因而其表面处理尤为重要,硝化／还原、氯磺化等化学改性和等离子体、电子束等物理改性均可改善芳纶纤维表面的物理和化学状态,提高其与基体间的粘合性能。     

低温等离子体处理对芳纶/环氧界面性能的影响

在采用低温等离子体对芳纶纤维进行表面处理后，用扫描电镜观察处理前后的纤维表面，测试了纤维的拉伸性能，并用单纤维抽拔法对芳纶纤维／环氧树脂的界面性能做了定量的表征。实验结果表明：经低温等离子体处理后，芳纶纤维表面变得粗糙，拉伸强度随处理时间延长而下降，纤维初始模量和断裂伸长率略有下降，而芳纶／环氧界面的粘结强度有所提高。     

高性能纤维的弯曲疲劳断裂研究

在自制弯曲疲劳装置上 ,对 3种高强对位芳纶及超高相对分子质量聚乙烯纤维 (Dyneema SK65 )进行双面弯曲疲劳试验。结果表明 ,Twaron 2 0 0 0弯曲疲劳寿命的自然对数与预加应力、弯曲角度呈线性关系 ,Dyneema SK65弯曲疲劳寿命明显长于对位芳纶 ,Twaron 2 0 0 0 ,Kevlar 12 9相近 ,都比Kevlar 2 9略长 ;高强型对位芳纶的弯曲疲劳断裂断口芯层呈现出“毛笔头”或“拔丝形”原纤化分裂形态 ,超高相对分子质量聚乙烯纤维弯曲疲劳断裂断口有明显的脆性折断形态 ,无原纤出现。     

常压等离子体处理芳砜纶的结构与性能研究

分别采用氦气和氦气/氧气对芳砜纶进行常压等离子体处理。采用滴水吸收实验测定处理前后纤维表面的润湿性,利用扫描电子显微镜和X射线光电子能谱仪分析处理前后纤维表面形态和化学成分的变化。结果表明:经常压等离子体处理后芳砜纶表面粗糙度增加,纤维表面碳元素含量下降,羟基、羧基等含氧或氮的极性基团增加,芳砜纶纱线的润湿性能提高,纱线强度没有明显变化,氦气/氧气等离子体处理比氦气等离子体处理效果更好。     

低温等离子体对UHMWPE纤维的表面改性

运用自行研制的常压低温等离子体设备对超高相对分子质量聚乙烯(UHMWPE)纤维进行了表面处理,选用正交试验法通过润湿性测试优化出不同工作气氛下的工艺条件,采用强力测试、扫描电镜(SEM)和光电子能谱仪(XPS)分析了等离子体处理前后UHMWPE纤维的性能变化。结果表明,常压低温等离子体在Ar携带丙烯酸和Ar／O2的气氛下处理UHMWPE纤维,表面改性效果良好。特别是选用Ar／O2流量比100:1,处理速度为5．8 m／min,输出功率189 W,可满足连续化生产。     

Influence of moisture regain of aramid fibers on effects of atmospheric pressure plasma treatment on improving adhesion with epoxy

One difference between a low‐pressure plasma treatment and an atmospheric pressure plasma treatment is that in the atmosphere, the substrate material may contain significant quantities of moisture, which could potentially influence the effects of the plasma treatment. To investigate how the existence of moisture affects atmospheric pressure plasma treatment, aramid fibers (Twaron 1000) with three different moisture regains (0.5, 4.5, and 5.5%) were treated by an atmospheric pressure plasma jet for 3 s at a gas flow rate of 8 L/min, a treatment head temperature of 100°C, and a power of 10 W. The scanning electron microscopy analysis showed no observable surface morphology change for the plasma treated samples. X‐ray photoelectron spectroscopy analysis showed the oxygen contents of the 0.5 and 4.5% moisture regain groups increased from that of the control, although the opposite was true for the 5.5% moisture regain group. The advancing contact angles of the treated fibers decreased about 8°–16° whereas their receding contact angles decreased about 17°–27°. The interfacial shear strengths of the treated fibers as measured using microbond pull‐out tests were more than doubled when the moisture regain was 4.5 or 5.5%, whereas it increased by 58% when the moisture regain was 0.5%. In addition, no significant difference in single fiber tensile strength was observed among the plasma treated samples and the control sample. Therefore, we concluded that moisture regain promoted the plasma treatment effect in the improvement of the adhesion property of aramid fibers to epoxy. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 242–247, 2006     

The effect of atmospheric‐pressure air plasma discharge power on adhesive properties of aramid fibers

After exposure to the atmospheric‐pressure air plasma at different discharge powers, the adhesion characteristics of Twaron aramid fibers were investigated. For the 12 s‐300 W plasma treatment, the interlaminar shear strength of Twaron fiber reinforced thermoplastic poly(phthalazinone ether sulfone ketone) was increased from 46.0 to 61.7 MPa by 34.1%, and the diffusion of water molecule into the resulting composites was proved to be effectively prevented. These results showed that surface adhesive properties of the plasma‐treated aramid fibers were improved. At the power level of 300 W, X‐ray photoelectron spectroscopy analysis revealed the increases in concentrations of oxygen and nitrogen polar groups on the fiber surface, and atomic force microscopy observations led to the conclusion that the fiber surface morphology was changed and the surface roughness was greatly increased. These new polar and irregular surface structures accounted for the better adhesion between the fiber and the matrix, while due to the reasonability of this discharge power level applied to the surface modification, the measured fiber tensile strength only decreased by 2.0%. POLYM. COMPOS., 37:620–626, 2016. © 2014 Society of Plastics Engineers     

Influence of temperature and relative humidity on aging of atmospheric plasma jet treatment effect on ultrahigh-modulus polyethylene fibers

The aging effects of atmospheric pressure plasma treated fiber surfaces are important for storage and processing of the fibers. One of the high-performance fibers, ultrahigh modulus polyethylene (UHMPE) fiber, was chosen as a model system to investigate the aging process of atmospheric pressure plasma jet (APPJ) treated fibers surfaces 0, 7, 15 and 30 days after initial plasma treatment. The fiber was first plasma-treated and then stored at temperatures varying from ?80 to 80°C on the same relative humidity (RH, 0%) and on RH of 0%, 65% and 100% at the same temperature of 20°C. Immediately after the plasma treatment, scanning electron microscope (SEM) showed the roughened fiber surface. X-ray photoelectron spectroscopy analysis showed changed surface chemical compositions. Contact-angle measurement showed increased surface wettability and microbond test showed an increase in IFSS. With increasing relative humidity or decreasing temperature, the IFSS value decreased and the contact angle increased more slowly. However, after 30 days, the IFSS values and contact angles reached a similar level for all groups. Moisture showed no effect on the single fiber tensile strengths during aging. The reasons for the observed aging behavior could be that decreasing temperature or increasing relative humidity hindered the surface rearrangement of polymer chains after plasma treatment.     

Wetting and adhesion behavior of armos fibers after dielectric barrier discharge plasma treatment

To investigate the influence of atmospheric plasma treatment on aramid fiber wetting and adhesion behavior, an air dielectric barrier discharge (DBD) was applied to the Armos aramid fiber surface at different discharge power densities. Dynamic contact angle analysis indicated that the total surface free energy was increased from 49.6 to 68.3 mJ/m 2 , an increment of 37.7%, whereas the single-fiber tensile strength testing showed that the mechanical properties of the Armos fibers were almost unaffected. With the enhancement of fiber surface wettability, the interlaminar shear strength, which was used to determine the interfacial adhesion in Armos-fiber-reinforced thermoplastic poly(phthalazinone ether sulfone ketone) composites, increased by 17.2% to 71.4 MPa. Scanning electron microscopy photos showed that the predominant failure mode of the composites changed from interface failure to matrix and/or fiber failure after the plasma treatment. Taken together, these results suggest that the air DBD plasma was an effective technique for improving the surface and interfacial performance of the Armos fibers without damaging their bulk properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

介质阻挡放电在芳纶表面改性中的应用

综述了介质阻挡放电应用于芳纶表面改性研究的最新进展;介绍了介质阻挡放电的机理、特点以及国内主要的介质阻挡放电等离子体的设备;阐述了介质阻挡放电对芳纶亲水性能和粘结性能等表面性能的改善。指出芳纶等离子体表面改性的时间效应限制了其广泛应用,应进一步加强纤维表面等离子体改性的机理研究。     

等离子体射流载气流量大小对玻璃纤维改性效果影响的研究

通过大气压等离子体射流在玻璃纤维（GF）表面沉积氧化硅（SiO_x）纳米颗粒的方法改善玻璃纤维增强聚丙烯（GFRP）复合材料的界面结合性能,利用扫描电子显微镜、原子力显微镜和X射线光电子能谱等表征分析了改性纤维的表面形貌、化学成分、润湿性能和复合材料的界面结合性能,并考察了等离子体射流载气流量大小对GF改性效果的影响。结果表明,当载气流量为40 mL/min时,GF的改性效果最好,且此时GF的表面能相比对照组提高了43.18 %,GFRP复合材料的层间剪切强度提高了30.79 %;经过等离子体处理后,GF的表面粗糙度增大,极性官能团增多,复合材料的界面结合性能提升。     

Effect of interface on the morphology and properties of composites comprising poly(propylene) and short organic fibers

The effect of the fiber surface modification with an azide derivative on the morphology and properties of composites based on poly(propylene) (PP) and short poly(ethylene terephthalate) (PET) and nylon 66 (PA) fibers, has been investigated. Both organic fibers act as reinforcement of the PP, and the reinforcing effect increases with the introduction of azide groups on the chemical structure of the fibers. This effect is more sensible in PP/short PET fiber composites although PA fibers gives rise to higher improvements in toughness. Scanning electron microscopy (SEM) has shown that the azide treatment of PET fibers gives rise to a better wettability and adhesion at the fiber/matrix interface. A good correlation between SEM and mechanical behavior of the composites has been observed.     

Effect of Glycerol Coating on the Atmospheric Pressure Plasma Treatment of UHMWPE Fibers

In order to investigate how coatings of glycerol affects atmospheric pressure plasma treatment, ultra high molecular weight polyethylene (UHMWPE) fibers were first pretreated with 0.2 and 0.6 mol/l glycerol solutions, respectively, and then were modified by an atmospheric pressure plasma jet (APPJ) using helium as the carrier gas with a flow rate of 20 l/min, discharge power of 30 W and a radio frequency of 13.56 MHz. After the plasma treatment, scanning electron microscopy (SEM) and atomic force microscopy (AFM) analysis revealed that the glycerol coated-APPJ treated samples possessed smoother surface than the APPJ directly treated samples. The X-ray photoelectron spectroscopy (XPS) analysis indicated that the changed content of oxygen containing groups on the surface of the glycerol coated groups compared with the non-glycerol coated group was mainly due to the remaining glycerol on the fiber surfaces. The water contact angle test revealed that the wettability of the glycerol coated-APPJ treated fibers decreased slightly in comparison with the APPJ directly treated fibers. Furthermore, the microbond pull-out test indicated that the interfacial bonding of the fiber to epoxy resin decreased when the fiber was pretreated with glycerol before plasma treatment. Therefore, it was concluded that the presence of glycerol on fiber surface weakened the effectiveness of APPJ treatment of UHMWPE fibers in improving the interfacial bonding to epoxy. This was mainly attributed to the consumption of plasma energy in etching the glycerol layer on the fiber surface and a weak interfacial layer due to the presence of residual glycerol.     

Effect of ultrasound on wettability between aramid fibers and epoxy resin

Good wetting of reinforced fiber by resin was a main factor in the improvement of the interface adhesion of their composites. Ultrasound with a frequency of 20 kHz was used to improve the wettability between aramid fibers and epoxy resin during the winding process of the composites. The effects of ultrasound on the viscosity and surface tension of epoxy resin and on the surface characteristics of aramid fibers were investigated. The wettability of aramid fibers and treated epoxy resin under different conditions and of aramid fibers and epoxy resin under ultrasonic online treatment were compared. The results indicated that the main action of ultrasound was to force epoxy resin to impregnate aramid fibers, in addition to the influence of ultrasound on the properties of epoxy resin and aramid fibers. The results of microdebond testing showed that the interfacial shear strength (IFSS) of aramid/epoxy composites could be 26% higher than that of untreated composites because of the improved wettability between aramid fibers and epoxy resin subjected to ultrasonic online treatment. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006