Performance Analysis of an Electric Clothes Dryer

Improving the energy efficiency of clothes dryers has been the subject of numerous investigations. However, to date the clothes drying process has not been thoroughly tested or analyzed in a comprehensive study. Many of the techniques that have been proposed to improve energy efficiency add to dryer cost or are environmentally unacceptable. In the present study, a commercial Frigidaire dryer was instrumented and evaluated for energy performance by changing operating parameters including heater power, fan speed, drum speed, weight, and initial moisture content of the clothes. The total drying time and energy consumption was monitored as well as the effect of air leakage into the drum. The experimental results from 32 runs of the dryer were evaluated. The results from these tests are discussed and techniques are proposed in an attempt to improve the energy efficiency of this unit.     

Numerical Optimization of the Annual Cost of a Clothes Dryer

Optimization of the energy cost of clothes dryers saves on energy use without requiring additional installations. To optimize the cost of clothes dryers, a correlation has been developed for the evaporative mass flux produced in the drum. The correlation was used to determine the drying time and cost. An objective function for the drying cost was defined in terms of the total annual dryer costs for energy usage, material, and manufacturing. The objective function (Annual cost) was optimized for two cases relative to 8-10 of the dryer parameters subject to various operating constraints using the direct search and the variable metric methods. The optimization results indicate that there are optimum settings for the fan speed and the drum speed depending on the weight of the drying load and heater power. The results showed that the optimum lies at the highest drying load and the lowest (37.45% in Annual cost could be saved) or the highest value of heater power (19.7% in Annual cost and 52.6% in drying time could be saved), whichever satisfies the drying time constraint. The applications of the optimization results are discussed.     

Enhancing the Energy Efficiency of Domestic Dryer by Drying Process Optimization

The domestic tumble dryers are becoming indispensable household appliances and responsible for up to 10% of the total residential energy use in developed countries. However, their energy efficiency is low. In this paper, the development of a multi-sensor computer-controlled prototype platform for fabric drying is described for improving the efficiency of dryers. The prototype platform enables the real-time control and recording of key drying parameters including heater power, air flow velocity, rotating speed of drying drum, and drying cycle time. These parameters are automatically adjusted according to the exhaust air humidity instead of the temperature which is used traditionally. Additionally, a new drying model of dividing the drying process into four stages based on the humidity of the exhaust air has been investigated to further increase the energy saving. The performance of this staged drying model is experimentally evaluated in respect to energy consumption, drying time, and the smoothness of fabric after drying. The results clearly indicate that the staged controlling of heating power input not only decreases energy consumption by 21.5%, but also improves the fabric smoothness by 0.9 grade compared to using a single heating power input for the whole drying process. The research outcome can enable the design and production of new dryers that are more energy efficient and lead to dried clothes that require less ironing, which in turn further reduces energy consumption.     

Modeling and simulation of drying characteristics on flexible filamentous particles in rotary dryers

Experiments were conducted to demonstrate the effects of the drum wall temperature on the heat and mass transfer in rotary dryers. The drying characteristics of flexible filamentous particles in rotary dryers were further explored. In addition, the inlet and outlet temperatures and moisture contents of granular particles were measured. As a result, the good agreement between the simulations and experiments verified the rationale and feasibility of the numerical method. Therefore, the approach was adopted to evaluate the temperature and moisture content of wet granular particles in a rotary dryer in different conditions, for instance, drum wall temperature and rotational speed. The results revealed that the higher drum wall temperature led to hotter particles with lower outlet moisture content. Conversely, the higher rotational speed resulted in cooler particles with higher outlet moisture content due to the decrease of residence time in the rotary dryer.     

Performance Study of a Closed-Type Heat Pump Tumble Dryer Using a Simulation Model and an Experimental Set-Up

In the interests of competitiveness, manufactures of tumble dryers are seeking to reduce both their electricity use and the drying time. This study examines how the cylinder volume of the compressor and the total heat transfer of the condenser influence the drying time and electricity use in a heat pump tumble dryer. A transient simulation model was developed and compared to an experimental set-up with good similarity. The simulations show that increasing the cylinder volume of the compressor by 50% decreases the drying time by 14% without using more electricity.     

Influence of drum inlet air conditions on drying process in a domestic tumble dryer

This study examines how the inlet air temperature, relative humidity, and flow rate influence the textile drying process in an open cycle tumble dryer. An experimental setup was prepared by connecting a domestic tumble dryer to an external system for controlled heating, humidification, and transport of air. Experiments were conducted by drying cotton textiles (8?kg dry mass) at different air inlet conditions. On the basis of measured data, correlations for determination of the total drying time, the moisture evaporation rate during the constant drying rate, and the area-mass transfer coefficient were developed. The process in the drum was modeled by using an established moisture evaporation model, based on sorption isotherms. A commonly used and a recently reported sorption isotherm for cotton were used with the model. Agreement between calculated and measured drying curves was better in case of the commonly used sorption isotherm, but final moisture content was better predicted by the recently reported sorption isotherm.     

A Diffusion Model for a Drum Dryer Subjected to Conduction, Convection, and Radiant Heat Input

Drum dryers are commonly used for production of a flaky dry powder from thick suspensions. This article presents results of a simple diffusion-based model to predict the drying performance of a pilot-scale twin-drum dryer. Numerical results are compared with experimental data obtained for a biological sludge whose initial moisture content varied from 1.0 to 2.3 kg/kg db. The agreement of model predictions with the pilot-scale experimental data is favorable. Effects of film thickness, drum rotational speed, external air flow velocity, and its humidity are examined parametrically. Sludge film thickness is identified as the most critical operating parameter to control the final moisture content and productivity of the dryer. The validated model is used to predict performance of a drum dryer subjected to heat input by convection and radiation along with conduction through the drum wall. It is shown that dryer output can be enhanced significantly by increasing the film thickness and applying radiant heating in the initial period of drying. A simple mathematical model of this type can be used for the purpose of design and analysis as well as scale-up of industrial drum dryers based on simple laboratory-scale experiments.     

Calculation Steps for the Design of Different Components of Heat Pump Dryers Under Constant Drying Rate Condition

Heat pump–assisted dryers are an alternative method for drying heat-sensitive food products at low temperature and less relative humidity with lower energy consumption. The mathematical models of a heat pump dryer consist of three submodels; namely, drying models, heat pump models, and performance models. Heat and mass balance of both refrigerant and air circuits in all components of the system are used for development of mathematical models. The models are used for design of different components of heat pump dryers operating under constant drying rate condition. A simple stepwise design procedure for batch-type, closed-loop heat pump dryer is also presented.     

Saffron Drying with a Heat Pump–Assisted Hybrid Photovoltaic–Thermal Solar Dryer

Saffron is the most expensive spice and Iran is the largest producer of this crop in the world. Saffron quality is profoundly affected by the drying method. Recent research has shown that hybrid photovoltaic–thermal solar power systems are more efficient in comparison with individual photovoltaic and thermal systems. In addition, heat pump dryers are highly energy efficient. Furthermore, they are suitable for heat-sensitive crops such as saffron. Therefore, in the present study, the performance of a hybrid photovoltaic–thermal solar dryer equipped with a heat pump system was considered for saffron drying, in order to obtain a high-quality product and reduce fossil fuel consumption. The effect of air mass flow rate at three levels (0.008, 0.012, and 0.016 kg/s), drying air temperature at three levels (40, 50, and 60°C), and two different dryer modes (with and without the heat pump unit) on the operating parameters of the dryer was investigated. The results of the investigation showed that total drying time and energy consumption decreased as air flow rate and drying air temperature increased. Applying a heat pump with the dryer led to a reduction in the drying time and energy consumption and an increase in electrical efficiency of the solar collector. The average total energy consumption was reduced by 33% when the dryer was equipped with a heat pump. Maximum values for electrical and thermal efficiency of the solar collector were found to be 10.8 and 28%, respectively. A maximum dryer efficiency of 72% and maximum specific moisture extraction rate (SMER) of 1.16 were obtained at an air flow rate of 0.016 kg/s and air temperature of 60°C when using the heat pump.     

MATHEMATICAL MODEL DEVELOPMENT AND SIMULATION OF HEAT PUMP FRUIT DRYER

ABSTRACT

A mathematical model of a heat pump fruit dryer was developed to study the performance of heat pump dryers. Using the moisture content of papaya glace' drying, the refrigerant temperature at the evaporator and condenser and the performance, was verified. It was found that the simulated results using closed loop heat pump dryer were close to the experimental results. The criteria for evaluating the performance were specific moisture extraction rate and drying rate. The results showed that ambient conditions affected significantly on the performance of the open loop dryer and the partially closed loop dryer. Also, the fraction of evaporator bypass air affected markedly on the performance of all heat pump dryers. In addition, it was found that specific air flow rate and drying air temperature affected significantly the performance of all heat pump dryers.     

低温热泵干燥装置的技术方案分析

低温热泵干燥装置在化学品、食品、药品、农副产品的干燥中具有广泛需要。给出了基本型、真空型和吸附剂型三类低温热泵干燥装置,对其结构、工作原理和特性进行了简要分析。分析表明,在初投资方面,基本型最低,真空型最高;在能源效率方面,真空型最高,基本型最低;吸附剂型在初投资和能源效率方面均居中。上述工作可为低温热泵干燥装置的设计提供较好的参考。     

一种衣物空气低温烘干循环系统的设计及分析

基于机械热泵除湿原理,同时结合洗衣机衣物烘干温度的要求,设计出一种衣物空气低温烘干循环系统。借助EES软件对该系统建立系统模型,通过理论模拟分析研究其热力学性能,并对影响其热力性能的关键操作参量影响进行分析。研究结果表明,在保证冷凝量均为1.02 kg/h的情况下,该设计系统的单位能耗除湿速率（moisture extraction rate,MER）为0.5018 kW?h/kg,较常规电加热热风烘干系统降低了16.5%;COP为0.79,较常规烘干系统提高了16.5%。此外,相比较常规电加热热风烘干系统方案烘干温度90 ℃,该方案设计的滚筒操作温度仅为57.68 ℃,有效地拓展了可烘干衣物的范围。     

回热式热泵干燥高湿稻谷的试验研究

应用带有嵌入回热器的热泵装置,对华南地区高湿稻谷进行干燥试验,测定其干燥速率、能耗和品质。并与同期作业的燃油低温循环稻谷干燥机进行对照。试验结果表明：回热式热泵干燥机的干燥速率较燃油低温循环干燥机提高20％,干燥周期缩短约12％,而干燥能耗及费用可节省30％以上,干燥品质两者无差异。     

Statistical analysis of clothing drying in a venting type dryer

An experimental study of the drying process using the prototype of a venting type dryer is presented. The machine has two motors: one for moving the drum and another for moving the turbine; electrical resistance is used as the heat source. The prototype operates under controlled test conditions in accordance with the Department of Energy (DOE) Standard 10 CFR 430. The aim of this study is to statistically determine the impact of the main factors and their interactions involved in the drying of clothing from a complete design of experiments. Statistical analyses for drying time and the energy consumption are determined from the studied factors. The factors studied are turbine motor frequency (to admit and expel air from the dryer); power supplied to the electric coil, amount and moisture of clothing and restriction of exhaust duct the gases. The results show that all of the studied factors and four of the interactions are statistically significant in the drying of clothes. The shortest drying time and the lowest energy consumption were obtained with the higher level of restriction and the lower initial moisture of clothing.     

热泵微波联合干燥系统研究

对热泵微波干燥的实用性及其性能进行了模拟分析和试验研究 ,试验及计算结果吻合较好。分析了空气旁通率、压缩机转速及空气质量流量等主要设计及运行参数对干燥性能的影响。与蒸汽加热干燥比较的结果表明 :通过精心设计热泵微波干燥系统 ,可使其能耗与蒸汽加热干燥相当。     

Efficient Energy Recovery with Wood Drying Heat Pumps

This article presents a 13-m³ wood dryer coupled with a 5.6-kW (compressor power input) heat pump. Drying tests with hardwood species such as yellow birch and hard maple were completed in order to determine the system's energy performance. Supplementary heating to compensate for the dryer heat losses was supplied using electrical coils or steam exchangers. The heat pump running profiles and dehumidification performance in terms of volumes removed and water extraction rates, coefficients of performance, and specific moisture extraction rates were determined for two all-electrical and two hybrid drying tests. The hardwood drying curves, share of the final moisture content, and final quality of the dried wood stacks, as well as total drying energy consumption and costs, were determined for each drying run. Finally, the total energy consumption of the drying cycles using a heat pump was compared with that of a conventional drying cycle using natural gas as a single energy source.     

A SIMPLE DYNAMIC MODEL FOR SOLID TRANSPORT IN ROTARY DRYERS

The solid particle movement in a rotary drum plays an important role in drying processes. The solid distribution in the drum affects the amount of contact surface between the solid and the gas. The retention time of solids influences the time particles can stay in contact with the gas in order to transfer heat and mass. Any heat and mass transfer model for a solid particle dryer must be able to predict solid flowrate and solid hold-up. There have been several reports in the literature regarding the modelling aspects of solid transport in dryers. If the model is developed for model-based control, it must be simple and yet represent dynamics of the system accurately. This paper addresses solid motion modelling and the effects of different variables involved in solid transport phenomena. Sugar drying process is the case study in this work. A steady state semi-empirical model was modified to predict solid hold-up and flowrate in rotary dryers. This model was incorporated into a heat and mass transfer model ;o predict solid moisture and temperature for inferential and model-based control purposes. Results of several experiments that have been used to investigate dynamics of the system in terms of solid motion and to validate the model are also presented. The approach advocated in this paper is directly applicable to the transport of other solids in rotary drum equipment and can thus be regarded as a generalized model.     

A SIMPLE DYNAMIC MODEL FOR SOLID TRANSPORT IN ROTARY DRYERS

ABSTRACT

The solid particle movement in a rotary drum plays an important role in drying processes. The solid distribution in the drum affects the amount of contact surface between the solid and the gas. The retention time of solids influences the time particles can stay in contact with the gas in order to transfer heat and mass. Any heat and mass transfer model for a solid particle dryer must be able to predict solid flowrate and solid hold-up. There have been several reports in the literature regarding the modelling aspects of solid transport in dryers. If the model is developed for model-based control, it must be simple and yet represent dynamics of the system accurately. This paper addresses solid motion modelling and the effects of different variables involved in solid transport phenomena. Sugar drying process is the case study in this work. A steady state semi-empirical model was modified to predict solid hold-up and flowrate in rotary dryers. This model was incorporated into a heat and mass transfer model ;o predict solid moisture and temperature for inferential and model-based control purposes. Results of several experiments that have been used to investigate dynamics of the system in terms of solid motion and to validate the model are also presented. The approach advocated in this paper is directly applicable to the transport of other solids in rotary drum equipment and can thus be regarded as a generalized model.     

INDIRECT THERMAL DRYING OF LIGNITE: DESIGN ASPECTS OF A ROTARY DRYER

An investigation of the thermal drying of lignite has been carried out, by using an indirect heat pilot rotary drum. The process aims at the production of dry lignite and clean steam as part of a gasification procedure. Both flighted and bare drum modes have been employed. Temperature profiles along the dryer length, the amount of evaporation (moisture conversion) and the solids residence time distribution (RTD) were measured. A non-isothermal model was tested under three different regimes of solids flow. Model integration, by taking account of experimental amount of evaporation at dryer exit and temperature profiles along the dryer length, has been utilized in the validation of drying kinetics and heat transfer correlations. Model predictions compare satisfactorily with the operating data of an indirect heat industrial lignite dryer. Overall heat transfer coefficients of the pilot rotary dryer were found to agree well with those reported for direct heat dryers.     

EXPERIMENTAL STUDY ON DRYING OF CHILLI IN A COMBINED MICROWAVE-VACUUM-ROTARY DRUM DRYER

This paper presents new data on drying chilli in a microwave-vacuum-rotary drum dryer. This novel technique is designed to combine the advantages of vacuum drying and evenly dispersed microwave energy in a rotary drum. The drying kinetic and the specific energy consumption at particular product moisture content were measured experimentally. Moreover, the effect of pressure inside the chamber and the rotational speed of the drum were also determined.