Comparative degradation data of polyesters and related poly(ester amide)s derived from 1,4‐butanediol,sebacic acid,and α‐amino acids

Two new sequential poly(ester amide)s (PEAs) derived from 1,4‐butanediol, sebacic acid, and L ‐alanine (PABA8) or glycine (PGBG8) are prepared and characterized. For comparative purposes the related polyesters (PEs) 4,10 and 6,10 are also studied. The calorimetric analysis shows that the inclusion of amino acids improves the thermal properties such as the melting temperature without a significant reduction in their thermal stability. All polymers show hydrolytic and enzymatic degradability. The degradation rates of the PEAs are higher for the alanine derivative (PABA8) because of its low crystallinity and the higher specificity of the essayed proteolytic enzymes. The PEs are only degraded faster when enzymes with esterase activity are employed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1815–1824, 2002     

Ring‐opening copolymerization of L‐lactide with ε‐caprolactone initiated by diphenylzinc

Copolymerization of mixtures of L ‐lactide and ε‐caprolactone has been initiated by diphenylzinc. The reaction conditions were investigated, to discover the effects on yield, molecular weight and microstructure of copolymers obtained. The temperature used varied between 50 and 120 °C, the molar ratio of monomer to initiator ranged between 90 and 1440 mol/mol, and the molar ratio of ε‐caprolactone to L ‐lactide employed was between 100/0 and 0/100 mol/mol. Copolymers were characterized by ¹H‐NMR, ¹³C‐NMR, DSC and gel permeation chromatography. The results indicate that incorporation of L ‐lactide to the growing chain is preferred and ε‐caprolactone is copolymerized after most of the L ‐lactide has been depleted. The microstructure of obtained copolyesters was affected considerably by transesterification reactions. It was observed that increasing reaction temperature, reaction time and concentration initiator was advantageous to the transesterification. The crystallinity of copolyester obtained was determined by differential scanning calorimetry. The results are in good agreement with both molar composition and sequence distribution of copolyesters. Copyright © 2006 Society of Chemical Industry     

Random polyesteramides based on ε‐caprolactone and glycine

A series of random polyesteramides (PEAs) based on ε‐caprolactone and glycine were synthesized by a direct melt polycondensation method. Their structure was fully characterized by NMR spectroscopy. High molar mass PEAs were obtained for glycine contents lower than 15 mol‐%. The resulting copolymers are semi‐crystalline and present increasing glass transition temperatures but decreasing melting points at increasing glycine contents. Some of these PEAs exhibit better thermal stability and higher Young's modulus and ultimate tensile strength than PCL homopolymer. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40573.     

Miscibility of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) with high molecular weight poly(lactic acid) blends determined by thermal analysis

An important strategy used in the polymer industry in recent years is blending two bio‐based polymers to attain desirable properties similar to traditional thermoplastics, thus increasing the application potential for bio‐based and bio‐degradable polymers. Miscibility of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) with poly(L ‐lactic acid) (PLA) were characterized using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). Three different grades of commercially available PLAs and one type of PHBV were blended in different ratios of 50/50, 60/40, 70/30, and 80/20 (PHBV/PLA) using a micro‐compounder at 175°C. The DSC and TGA analysis showed the blends were immiscible due to different stereo configuration of PLA polymer and two distinct melting temperatures. However, some compatibility between PHBV and PLA polymers was observed due to decreases in PLA's glass transition temperatures. Additionally, the blends do not show clear separation by SEM analysis, as observed in the thermal analysis. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Application of low loading of collagen in electrospun poly[(l‐lactide)‐co‐(ε‐caprolactone)] nanofibrous scaffolds to promote cellular biocompatibility

Electrospinning of various polymers has been used to produce nanofibrous scaffolds that mimic the extracellular matrix and support cell attachment for the potential repair and engineering of nerve tissue. In the study reported here, an electrospun copolymer of l ‐lactide and ε‐caprolactone (67:33 mol%) resulted in a nanofibrous scaffold with average fibre diameter and pore size of 476 ± 88 and 253 ± 17 nm, respectively. Blending with low loadings of collagen (<2.5% w/w) significantly reduced the average diameter and pore size. The uniformity of fibre diameter distributions was supported with increasing collagen loadings. The nanofibrous scaffolds significantly promoted the attachment and proliferation of olfactory ensheathing cells compared to cells exhibiting asynchronous growth. Furthermore, analysis of cell health through mitochondrial activity, membrane leakage, cell cycle progression and apoptotic indices showed that the nanofibrous membranes promoted cell vigour, reducing necrosis. The study suggests that the use of more cost‐effective, low loadings of collagen supports morphological changes in electrospun poly[(l ‐lactide)‐co‐(ε‐caprolactone)] nanofibrous scaffolds, which also support attachment and proliferation of olfactory ensheathing cells while promoting cell health. The results here support further investigation of the electrospinning of these polymer blends as conduits for nerve repair. © 2013 Society of Chemical Industry     

Influence of α′‐/α‐crystal polymorphism on properties of poly(l‐lactic acid)

Poly(l ‐lactic acid) (PLLA) is a biodegradable and biocompatible thermoplastic polyester produced from renewable sources, widely used for biomedical devices, in food packaging and in agriculture. It is a semicrystalline polymer, and as such its properties are strongly affected by the developed semicrystalline morphology. As a function of the crystallization temperature, PLLA can form different crystal modifications, namely α′‐crystals below about 120 °C and α‐crystals at higher temperatures. The α′ modification is therefore of special importance as it may be the preferred polymorph developing at processing‐relevant conditions. It is a metastable modification which typically transforms into the more stable α‐crystals on annealing at elevated temperature. The structure, kinetics of formation and thermodynamics of α′‐ and α‐crystals of PLLA are reviewed in this contribution, together with the effect of α′‐/α‐crystal polymorphism on the properties of PLLA. © 2018 Society of Chemical Industry     

Part 7. Effects of poly(L‐lactide‐co‐ϵ‐caprolactone) on morphology,structure, crystallization,and physical properties of blends of poly(L‐lactide) and poly(ϵ‐caprolactone)

Blended films of poly(L ‐lactide) [ie poly(L ‐lactic acid)] (PLLA) and poly(?‐caprolactone) (PCL) without or mixed with 10 wt% poly(L ‐lactide‐co‐?‐caprolactone) (PLLA‐CL) were prepared by solution‐casting. The effects of PLLA‐CL on the morphology, phase structure, crystallization, and mechanical properties of films have been investigated using polarization optical microscopy, scanning electron microscopy, differential scanning calorimetry and tensile testing. Addition of PLLA‐CL decreased number densities of spherulites in PLLA and PCL films, and improved the observability of spherulites and the smoothness of cross‐section of the PLLA/PCL blend film. The melting temperatures (T_m) of PLLA and PCL in the films remained unchanged upon addition of PLLA‐CL, while the crystallinities of PLLA and PCL increased at PLLA contents [X_PLLA = weight of PLLA/(weight of PLLA and PCL)] of 0.4–0.7 and at most of the X_PLLA values, respectively. The addition of PLLA‐CL improved the tensile strength and the Young modulus of the films at X_PLLA of 0.5–0.8 and of 0–0.1 and 0.5–0.8, respectively, and the elongation at break of the films at all the X_PLLA values. These findings strongly suggest that PLLA‐CL was miscible with PLLA and PCL, and that the dissolved PLLA‐CL in PLLA‐rich and PCL‐rich phases increased the compatibility between these two phases. © 2003 Society of Chemical Industry     

Enhanced crystallization of poly(L‐lactide‐co‐ε‐caprolactone) during storage at room temperature

Copolymer of L ‐lactide and ε‐caprolactone [P(LLA‐CL)] (50/50) was synthesized using stannous octoate and was stored at room temperature. The change in physical properties occurring during this storage at room temperature was investigated by differential scanning calorimetry (DSC), X‐ray diffractometry, polarizing optical microscopy, tensile and bending tests, and light absorbance measurements. It was concluded that the increase in mechanical properties and light absorbance during storage can be ascribed to gradual selective crystallization of the L ‐lactide sequence in P(LLA‐CL) at room temperature. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 947–953, 2000     

Synthesis and characterization of α‐amino acid‐containing polyester: poly[(ε‐caprolactone)‐co‐(serine lactone)]

Novel polyesters, poly[(ε‐caprolactone)‐co‐(N‐trityl‐L ‐serine‐β‐lactone)]s, were prepared by copolymerizing ε‐caprolactone (CL) with N‐trityl‐L ‐serine‐β‐lactone (TSL) using ZnEt₂ as the catalyst. The number‐average molecular weights were determined which ranged from 2.7 × 10⁴ to 4.9 × 10⁴ Da with dispersity values ranging from 1.6 to 1.8. The structures of the copolymers were investigated by means of ¹H NMR, ¹³C NMR and infrared spectroscopies, thermogravimetric analysis and differential scanning calorimetry. The results indicated that CL and TSL monomer units were randomly distributed within the copolymer backbone structures and the ratios of TSL to CL in the copolymers were close to those in the feeds. After removal of the trityl group under mild condition, a new polyester with side amino groups provided by serine units was obtained. L929 cell culturing test indicated good biocompatibility of the polyester with or without protective groups. © 2012 Society of Chemical Industry     

Synthesis and characterization of degradable copoly(ester–amide)s: Poly(trans‐4‐hydroxy‐L‐proline‐co‐ε‐caprolactam)

Novel copolyesteramides were synthesized by reacting trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L ‐proline (N‐CBz‐Hpr) with ε‐caprolactam (CLM) in the presence of stannous octoate [Sn(II) Oct.] as a catalyst. Various techniques, including ¹H‐NMR, IR, DSC, and viscosity, were used to elucidate structural characteristics and thermal properties of the resulting copolymers. Data showed that the optimal reaction condition for the synthesis of the copolymers was obtained by using 3 wt % Sn(II) Oct. at 170°C for 24 h. The DSC analysis demonstrated amorphous structure for most of the copolymers. The glass‐transition temperature of the copolymers shifts to a higher temperature with increasing Hpr/CLM molar ratio. In vitro degradation of these poly(N‐CBz‐Hpr‐co‐CLM)s was evaluated by weight loss measurements. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1615–1621, 2002     

Effects of plasma treatment on biocompatibility of poly[(L‐lactide)‐co‐(ϵ‐caprolactone)] and poly[(L‐lactide)‐co‐glycolide] electrospun nanofibrous membranes

Poly[(l ‐lactide)‐co ‐(? ‐caprolactone)] (PLCL) and poly[(l ‐lactide)‐co ‐glycolide] (PLGA) copolymers are widely used in neural guide tissue regeneration. In this research, the surface modification of their hydrophilicity was achieved using plasma treatment. Attachment and proliferation of olfactory ensheathing cells on treated electrospun membranes increased by 26 and 32%, respectively, compared to the untreated PLCL and PLGA counterparts. Cells cultivated on both the PLCL and PLGA membranes showed high viability (>95%) and healthy morphologies with no evidence of cytotoxic effects. Cells grown on treated electrospun fibres displayed significant increases in mitochondrial activity and reductions in membrane leakage when compared to untreated samples. The results suggested that plasma treatment of the surface of the polymers enhanced both cell viability and growth without incurring any cytotoxic effects. © 2017 Society of Chemical Industry     

Synthesis and properties of non‐cytotoxic poly(l‐malic acid acetate‐co‐l‐lysine ester)s with thermo‐sensitivity as hydrophobic drug nanocarrier

In this investigation, a group of poly(l ‐malic acid acetate‐co‐l ‐lysine ester)s (PMALs) with excellent thermo‐sensitivity and non‐cytotoxicity were prepared by an optimized synthetic route from natural l ‐malic acid and l ‐lysine. The structure and properties of PMALs including monomers were systematically characterized by FTIR, ¹H NMR, UV, gel permeation chromatograph, scanning electron microscope, contact angle measurement, cell counting kit assess (CCK‐8), and confocal laser scanning microscopy (CLSM). Three PMALs show a reversible lower critical solution temperature of 8–36 °C depending on their chemical structure. The contact angle measurement revealed a considerable discrepancy in the hydrophilicity/hydrophobicity of PMALs and further influence on their thermo‐sensitivity. The viability of HeLa cells exposed to 0.2–100 μg/mL PMALs solution was found to be in a range 80–103% after 24, 48, and 72 h of incubation, indicating no cytotoxicity. Moreover, a spherical nanocarrier with core‐shell structure was facilely fabricated via the thermo‐sensitivity of PMALs and hydrophobicity of drug. CLSM observations manifested that the hydrophobic‐curcumin‐enwrapped nanocarriers can clearly internalize into the cellular inside. The sustained release of curcumin from nanocarriers in vitro provided a possibility of depressing fast hydrolytic degradation at physiological pH or other side‐effects. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45984.     

Synthesis and characterization of a new family of cationic amino acid‐based poly(ester amide)s and their biological properties

A new family of positively charged and water soluble amino acid‐based poly(ester amide)s (PEAs) consisting of nontoxic L ‐arginine, diols, and aliphatic dicarboxylic acids building blocks was synthesized and characterized. The L ‐arginine based PEAs (Arg‐PEAs) were prepared by a solution polycondensation of two monomers: tetra‐p‐toluenesulfonic acids salts or hydrochloride acid salts of bis‐(L ‐arginine) α, ω‐alkylene diesters (monomer II ), and di‐p‐nitrophenyl esters of saturated or unsaturated dicarboxylic acids (monomer I ). Optimal reaction conditions were studied as functions of type of solvents and acid acceptors, concentrations of reactants. The molecular weights (M_n and M_w) of Arg‐PEAs measured by GPC ranged from 20,000 to 60,000 g mol^?1 with a rather narrow molecular weight distribution below 1.5. The chemical structures were confirmed by IR and NMR spectra. Arg‐PEAs obtained were all amorphous materials with T_g from 33 to 125°C, depending on the number and the type (saturated vs. unsaturated) of methylene groups in diols or diacids, and the type of counter‐ions attached to the guanidine group of the Arg‐based PEAs. The Arg‐PEAs had a high solubility in all polar solvents, including water. Preliminary studies of cell morphology and DNA capture capability of Arg‐PEAs indicated that this new family of cationic PEAs was nontoxic and more biocompatible than a commercial transfection agent (Superfect®), and can successfully capture plasma DNA. The strong positive charge of Arg‐PEAs as well as their good water solubility could provide unique characteristics for potential gene transfection or other charge preferred biomedical applications. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Hydrolytic degradation and crystallization behavior of linear 2‐armed and star‐shaped 4‐armed poly(l‐lactide)s: Effects of branching architecture and crystallinity

“Linear” aliphatic polyesters composed of two poly(l ‐lactide) arms attached to 1,3‐propanediol and “star‐shaped” ones composed of four poly(l ‐lactide) arms attached to pentaerythritol (2‐L and 4‐L polymers, respectively) with number‐average molecular weight (M_n) = 1.4–8.4 × 10⁴g/mol were hydrolytically degraded at 37°C and pH = 7.4. The effects of the branching architecture and crystallinity on the hydrolytic degradation and crystalline morphology change were investigated. The degradation mechanism of initially amorphous and crystallized 2‐L polymers changed from bulk degradation to surface degradation with decreasing initial M_n; in contrast, initially crystallized higher molecular weight 4‐L polymer degraded via bulk degradation, while the degradation mechanism of other 4‐L polymers could not be determined. The hydrolytic‐degradation rates monitored by molecular‐weight decreases decreased significantly with increasing branch architecture and/or higher number of hydroxyl groups per unit mass. The hydrolytic degradation rate determined from the molecular weight decrease was higher for initially crystallized samples than for initially amorphous samples; however, that of 2‐L polymers monitored by weight loss was larger for initially amorphous samples than for initially crystallized samples. Initially amorphous 2‐L polymers with an M_n below 3.5 × 10⁴g/mol crystallized during hydrolytic degradation. In contrast, the branching architecture disturbed crystallization of initially amorphous 4‐L polymers during hydrolytic degradation. All initially crystallized 2‐L and 4‐L polymers had δ‐form crystallites before hydrolytic degradation, which did not change during hydrolytic degradation. During hydrolytic degradation, the glass transition temperatures of initially amorphous and crystallized 2‐L and 4‐L polymers and the cold crystallization temperatures of initially amorphous 2‐L and 4‐L polymers showed similar changes to those reported for 1‐armed poly(l ‐lactide). © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41983.     

Poly‐α,β‐(3‐hydroxypropyl)‐DL‐aspartamide: A new drug carrier

Poly‐α,β‐(3‐hydroxypropyl)‐DL ‐aspartamide (PHPA) was synthesized by the ring‐open reaction of polysuccinimide (PSI) and 3‐hydroxypropylamine. The polymer was characterized by ¹H‐NMR, ¹³C‐NMR, FTIR, and GPC. Mark–Houwink coefficients were obtained from viscometry and GPC measurements, K = 5.53 × 10⁻³ and α = 0.78 in water. The acute toxicity of PHPA was examined and it revealed no death in ICR mice up to the dose treated of 15.3 kg/kg, and hematological parameters showed no significant difference between treated and control animals. The potential use of PHPA as a drug carrier was also investigated. In a typical case, a contraceptive drug, norethindrone (NET), was bonded to PHPA, and the drug sustained released as long as 120 days an in vitro test. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2411–2417, 2000     

A robust affinity chromatography system based on ceramic monoliths coated with poly(amino acid)‐based polymeric constructs

Traditional chromatographic separation systems are disadvantaged by low flow rates, a high pressure drop across the column, low capacity and poor reusability. Searching for more efficient separation systems we introduced the use of a ceramic monolith as robust support in bioseparations. A coating consisting of l ‐asparagine as ligand, poly(l ‐lysine) as spacer arm and a commercial poly(ethylene acrylic acid) film forming copolymer network (Michem 4983‐40R) was developed as a coating for these ceramic monoliths. Poly(l ‐lysine) was synthesized by ring‐opening polymerization of ε‐trifluoroacetyl‐l ‐lysine N‐carboxyanhydride and coupled to a commercial film‐forming poly(ethylene acrylic acid) network. This construct was then ‘decorated’ with l ‐asparagine via the terminal amino functional groups of poly(L‐lysine) and coated onto the ceramic monolith to selectively bind l ‐asparaginase. Adsorption/elution experiments showed reversible binding between l ‐asparagine and l ‐asparaginase, and the subsequent release of l ‐asparaginase, and between 83% and 94% of the active enzyme was recovered by elution with d ‐asparagine and NaCl solutions. The functional activity of the eluted l ‐asparaginase was verified by a Nessler's assay. While traditional separation processes (adsorption and elution) using gel bead packings take many hours, the ceramic monolith system achieves the same of level of separation in about 1 h. This new system served as a proof of concept for its application in protein separation and purification. This work paves the way to a better understanding of the use of ceramic monoliths as stationary phase coated with a stable polymer construct for more robust and efficient supports in affinity chromatography. © 2020 Society of Industrial Chemistry     

Multi‐Enzymatic Synthesis of Optically Pure β‐Hydroxy α‐Amino Acids

A novel enzymatic production system of optically pure β‐hydroxy α‐amino acids was developed. Two enzymes were used for the system: an N‐succinyl L ‐amino acid β‐hydroxylase (SadA) belonging to the iron(II)/α‐ketoglutarate‐dependent dioxygenase superfamily and an N‐succinyl L ‐amino acid desuccinylase (LasA). The genes encoding the two enzymes are part of a gene set responsible for the biosynthesis of peptidyl compounds found in the Burkholderia ambifaria AMMD genome. SadA stereoselectively hydroxylated several N‐succinyl aliphatic L ‐amino acids and produced N‐succinyl β‐hydroxy L ‐amino acids, such as N‐succinyl‐L ‐β‐hydroxyvaline, N‐succinyl‐L ‐threonine, (2S,3R)‐N‐succinyl‐L ‐β‐hydroxyisoleucine, and N‐succinyl‐L ‐threo‐β‐hydroxyleucine. LasA catalyzed the desuccinylation of various N‐succinyl‐L ‐amino acids. Surprisingly, LasA is the first amide bond‐forming enzyme belonging to the amidohydrolase superfamily, and has succinylation activity towards the amino group of L ‐leucine. By combining SadA and LasA in a preparative scale production using N‐succinyl‐L ‐leucine as substrate, 2.3 mmol of L ‐threo‐β‐hydroxyleucine were successfully produced with 93% conversion and over 99% of diastereomeric excess. Consequently, the new production system described in this study has advantages in optical purity and reaction efficiency for application in the mass production of several β‐hydroxy α‐amino acids.

     

Syntheses of poly(lactic acid‐co‐glycolic acid) serial biodegradable polymer materials via direct melt polycondensation and their characterization

The optimal synthetic conditions of poly(lactic acid‐co‐glycolic acid) (PLGA) via melt copolycondensation directly from L ‐lactic acid (L ‐LA) and glycolic acid (GA) with a feed molar ratio of 50/50 are discussed; the important drug‐delivery carrier PLGA50/50 is used as a special example. With reaction conditions of 165°C and 70 Pa and with 0.5 wt % SnCl₂ as the catalyst, 10 h of polymerization gave the L ‐PLGA50/50 with the biggest intrinsic viscosity ([η]), 0.1993 dL/g. The optimal synthetic conditions were verified by the synthesis of D,L ‐PLGA50/50 with D,L ‐lactic acid (D,L ‐LA) instead of L ‐LA, but the biggest [η] was 0.2382 dL/g. Under the same synthetic conditions with L ‐LA and D,L ‐LA as starting materials, serial PLGA with different molar feed ratios, including 100/0, 90/10, 70/30, 50/50, 30/70, 10/90, and 0/100, were synthesized via simple and practical direct melt copolycondensation, and their solubilities were investigated. When the glycolic acid feed molar percentage was equal to or more than 70%, solubilities in tetrahydrofuran and CHCl₃ became worse, and some samples were even wholly insoluble. These biodegradable polymers were also systematically characterized with gel permeation chromatography, Fourier transform infrared spectroscopy, ¹H‐NMR spectroscopy, differential scanning calorimetry, and X‐ray diffraction. PLGA synthesized from L ‐LA and D,L ‐LA had many differences in weight‐average molecular weight (M_w), glass‐transition temperature, crystallinity, and composition. When the molar feed ratio of LA to GA was 50/50, both the [η] and M_w values of D,L ‐PLGA were higher than those of L ‐PLGA. With D,L ‐LA as the starting material, the structure of the PLGA copolymer was relatively simple, and its properties were apt to be controlled by its GA chain segment. When the feed molar percentage of the monomer (LA or GA) was more than or equal to 90%, the copolymer was apt to be crystalline, and the aptness was more obvious for the L ‐LA monomer. The composition percentage of GA in PLGA was not only higher than the feed molar percentage of GA, but also, the GA percentage in D,L ‐PLGA was higher than in L ‐PLGA. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 244–252, 2006     

Effects of copolymer microstructure on the properties of electrospun poly(l‐lactide‐co‐ε‐caprolactone) absorbable nerve guide tubes

The main objective of this work has been to study the effects of copolymer microstructure, both chemical and physical, on the microporosity, in vitro hydrolytic degradability and biocompatibility of electrospun poly(l ‐lactide‐co‐ε‐caprolactone), PLC, copolymer tubes for potential use as absorbable nerve guides. PLC copolymers with L : C compositions of 50 : 50 and 67 : 33 mol % were synthesized via the ring‐opening copolymerization of l ‐lactide (L) and ε‐caprolactone (C) at 120°C for 72 h using stannous octoate (tin(II) 2‐ethylhexanoate) and n‐hexanol as the initiating system. Electrospinning was carried out from solution in a dichloromethane/dimethylformamide (7 : 3 v/v) mixed solvent at room temperature. The in vitro hydrolytic degradation of the electrospun PLC tubes was studied in phosphate buffer saline over a period of 36 weeks. The microporous tubes were found to be gradually degradable by a simple hydrolysis mechanism leading to random chain scission. At the end of the degradation period, the % weight retentions of the PLC 50 : 50 and 67 : 33 tubes were 15.6% and 70.2%, respectively. Pore stability during storage as well as cell attachment and proliferation of mouse fibroblast cells (L929) showed the greater potential of the PLC 67 : 33 tubes for use as temporary scaffolds in reconstructive nerve surgery. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4357–4366, 2013     

Synthesis and characterization of well‐defined random and block copolymers of ε‐caprolactone with l‐lactide as an additive for toughening polylactide: Influence of the molecular architecture

Well‐defined multiarmed star random and block copolymers of ε‐caprolactone with l ‐lactide with controlled molecular weights, low polydispersities, and precise numbers of arms were synthesized by the ring‐opening polymerization of respective cyclic ester monomers. The polymers were characterized by ¹H‐NMR and ¹³C‐NMR to determine their chemical composition, molecular structure, degree of randomness, and proof of block copolymer formation. Gel permeation chromatography was used to establish the degree of branching. Star‐branched random copolymers exhibited lower glass‐transition temperatures (T_g's) compared to a linear random copolymer. When the star random copolymers were melt‐blended with poly(l ‐lactic acid) (PLA), we observed that the elongation of the blend increased with the number of arms of the copolymer. Six‐armed block copolymers, which exhibited higher T_g's, caused the maximum improvement in elongation. In all cases, improvements in the elongation were achieved with no loss of stiffness in the PLA blends. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43267.